Free Shipping on Orders Over $109 at Summit Racing

BendPak HD-9XW Standard Width Extra-Tall Lifts

The space saving design of the 9,000 lb. capacity BendPak HD-9XW is ideal for vehicle storage in residential garages or commercial buildings. It also happens to make a great service lift for smaller shops who still want to do a big business. These lifts are about the size of a typical parking space, helping to maximize floor space. The BendPak HD-9XW is great for storing ATVs, snowmobiles, jet skis, golf carts, boats or just about anything else that needs to be off the ground. You can finally make use of that wasted vertical space above your car. Additional features include the following: * 9,000 lbs. maximum lifting capacity * Freestanding design * Runways accommodate narrow and standard vehicles * Electric / hydraulic power system * Single hydraulic cylinder mounted underneath runway * Fully enclosed lifting cables, safety locks and sheaves * Internal anti-sway slider blocks in each column * Oversized self-lubricating cable rollers * Features heavy-duty 3/8 in. aircraft cable * Rugged 1 1/4 in. roller axles * Multi-position safety locks in each column * Adjustable lock ladders * Runways feature non-skid surface * Push-button pneumatic safety release * Independent backup slack-cable safety latches * Removable approach ramps for additional drive-under clearance

4.86 out of 5 stars ( 14 )

$6,495.00

Heidts 1964-70 Ford Mustang PRO-G Independent Rear Suspension Kits

Heidts Pro-G IRS suspension kits are designed to bring the superior ride and handling of independent rear suspension to your muscle car. Out-handle the competition and put all of that horsepower to the ground. Heidts Pro-G IRS suspension kits produce 1/2 degree of camber curve at 3/4 of bump, especially during very high cornering loads. Features include: * Cast iron Ford 9 in. center section mounted in an aluminum housing * 31-spline posi-traction hooked up to heavy-duty half shaft CV joint axle shafts * Tubular upper and lower control arms * Steel outer uprights * Top crossmember * Frame mounting brackets * Wilwood rear brake rotors and calipers * Billet aluminum single adjustable coilover shocks with silver powdercoated springs

Not Yet Reviewed

$14,973.00

EMAX Industrial Piston Compressors

Offering the same quality and durability as their Industrial Plus Series (without the extra cost of some features), EMAX Industrial piston compressors are designed for up to 50,000 hours of commercial or industrial use with proper maintenance. At the core of these extremely durable compressors are super-quiet pumps featuring cast iron crankcases, precision-balanced cast iron crankshafts, and high-quality stainless steel roller bearings to ensure smooth, efficient operation. For long life and rebuildability, EMAX adds steel connecting rods with replaceable rod bearing inserts, removable cast iron cylinders and cylinder heads, disc intake and exhaust valves, and cast iron flywheels with built-in fans. These bigger low-rpm pumps have a larger bore and stroke, so you get big cfm output with reduced friction and heat buildup. Industrial Series compressors have name brand, open-drip (OPD), low-rpm motors (1,750 rpm). Because of their higher torque factor, compared to the 3,450 rpm motors most manufacturers use, they run much cooler. With low harmonic distortion, these motors provide much higher torque in cold weather starting, and require less electricity to start. Other features include large starting and running capacitors, and dynamically balanced armatures. Running and starting windings are all copper-wound for premium efficiency, reliable performance, and durability. These motors meet all UL and CSA requirements and include pre-wired Condor combination starter and pressure switches with actuation-type diaphragms. EMAX uses only taper-lock style, 2-groove pulleys with dual 2-groove, B-style belts to drive their pumps. Dual belts ensure long belt life with low vibration for smoother, quieter operation because dual belts do not have to be as tight as a single belt. Tighter belts put more load on the compressor pump and the motor bearings; that decreases the life of both. Much better than a fixed bore pulley with a set screw; the taper-lock design locks the pulley in position on the motor shaft preventing it from loosening or moving. EMAX piston compressors also feature: * Head unloaders allow for load-less starting and can help cool the pump in high-duty cycle applications * Built-in inter-coolers and after-coolers * OSHA-approved, 13-gauge steel, expanded metal belt guards * ASME code-compliant tanks * Extended tank water drain pipes plumbed to the front with 1/4 in. ball valve handles * 100 percent brass check valves, safety valves, and ball valves * Top-quality plumbing fittings * Big 1 3/8 in. output shafts * 15 Service Factor motors can be pulled 15 percent over full load

4.5 out of 5 stars ( 2 )

$8,394.60

FTI Performance Pro Powerglide Level 5.5 Transmissions

Delivering big power for racers, FTI Performance Pro Powerglide Level 5.5 transmissions are an unbreakable unit. Equipped with the FTI creatively designed spiral springs and valve body, these units don't creep when the brake is set—a must in today's racing world. With in-house machining, the transmissions are hand-assembled by one builder, and every clearance is set to exacting tolerances. FTI automatic transmissions house the greatest advances in Powerglide racing technology, and are designed to withstand the rigors of today's high performance engines in an extremely demanding environment. Other features include: * 2200 advertised horsepower rating * Protree transbrake 265 lbs. * Lightened steel clutch hub * 1.80 or 1.69 straight cut planetary * Vasco input shaft * 10-clutch drum * Pro mod wideband * High-flow pump * 300M output shaft

Not Yet Reviewed

$5,349.00

BendPak PCL-18B Cross Beams

BendPak's PCL-18B cross beams for their portable column lifting systems connect two mobile column lifts, allowing you to lift most heavy-duty commercial vehicles safely and securely. Featuring single-piece construction, these chassis support beams have rugged stainless steel frames with a rust-, chemical-, and abrasion-resistant finish. Each BendPak cross beam has an 18,000 lb. capacity and lifts vehicle from the chassis frame, giving you complete wheels-free access to perform a variety of wheel maintenance.

Not Yet Reviewed

$5,595.00

BendPak MDS-6EXT Mid-Rise Open-Center Car Lifts

The BendPak MDS-6EXT mid-rise open-center car lifts are the ideal solution for quick-lube stations looking to install a car lift flush over their work pits. You haven't experienced state-of-the-art portable lifting convenience until you've used a BendPak MDS-6EXT mid-rise scissor lift. This family of 6,000-lb. capacity mid-rise lifts comes loaded with adjustable arm assemblies, safety lock bars with multiple lock positions. The next generation of electric vehicles has arrived, and it didn't go unnoticed by BendPak that the lifting points of these vehicles are very different. Using long-wheelbase vehicles, which includes some very popular electric cars, as BendPak's point of reference, they designed the MDS-6EXT mid-rise open-center car lift to accommodate longer lifting points that better reach the extreme edges of the vehicle underbody. If your shop wants to be ready for longer-wheelbase vehicles, no matter how low the suspension, you can't do better than this BendPak model. Specifications for the BendPak MDS-6EXT mid-rise open-center car lifts: * Each lift platform features four solid steel-scissor frame support bars, making it one of the strongest mid-rise lifts in its class * Powdercoat finish provides a long-lasting durable finish * Comes standard with four durable cushioned and rubber contact blocks, permitting fast vehicle setup * Three locking positions allow technicians to work at different working heights to increase productivity and minimize fatigue * Dual master hydraulic cylinder combines with dual equalizing cylinders to provide a safe and level 6,000 pound lifting capacity * Solid steel safety lock bars engage automatically during ascent * Convenient stainless steel pneumatic cylinders simultaneously release safety locks during descent with a simple push of a button (requires min. 50 psi, 10 cfm air source at time of installation) * A push-button safety lock release system is operated away from the lift and allows operators to safely deactivate the locks without the need to push or pull cumbersome release bars or lock release handles * Hinge point features Zerk grease fitting to allow lubrication at critical wear areas

Not Yet Reviewed

$8,295.00

BendPak Add-On Shared Column and Platform 2-Post Parking Lifts

The BendPak PL-6000DC is an add-on shared column and platform two-post parking lift specifically designed to accommodate the needs of real estate developers, architects, engineers, automotive dealers, and commercial parking operators. They can be ganged together with shared columns allowing you to fit more units into a smaller space. The PL-6000DC dual-column parking lift can accommodate a wide array of vehicles including SUVs, sedans, and sports cars and offers the perfect combination for both long-term and short-term parking. Typically, long-term parking is the upper level and short-term parking below. They can be installed inside a typical 8-foot parking space to accommodate most cars and light trucks and operate in both indoor and outdoor locations. Product specs and advantages: * Low operating cost—platform driven by gravity when lowered, no electric motor consumption is required * Designed for installation on typical parking surfaces—detailed installation manual is provided along with floorplan and foundation drawings and video attached with products will help customers have easier installation work * Ganged column design allows multiple installations in minimum space * Commercial grade design and construction—add-on column for PL-6000DC lifts; lifting capacity: 6,000 lbs. (2,722 kg) * Galvanized and corrugated anti-slip platform * Freestanding design when ganged two or wide * Overhead power unit provides smooth quiet hydraulic operation * Platform can be stopped at different heights to fit various vehicles and ceiling heights * Full-width channel-locked center panels protect lower vehicle * Wide deck platform accommodates pickups, vans, and cars * Dual direct-drive hydraulic cylinders * Automatic safety lock combined with anti-fall device to hold platform securely * Virtually maintenance-free composite carriage bearings * Electric key switch for security and safety * Automatic shut-off when operator releases key switch * Manual lock release available in case electricity failure (optional) * Hydraulic overloading protection * Photocell sensor prohibits lift to be lowered if vehicle is parked below Safety features: * Mechanical safety locks are spaced every 4 inches * 24 V operator controls and lock release * Photocell sensor prohibits lift to be lowered if vehicle is parked below * Electric protection for power overload or improper voltage * Automatic locking system during power outage * Emergency stop button * Upper limit switch * Pressure relief valve and pressure compensated flow control valve to ensure safe operation and level lifting * Industrial-grade hydraulic cylinders feature a single-piece, pilot fitted, machined steel piston, wrapped with specially designed, pressure loaded U-cup piston seals, backups, and wear bands to virtually eliminate fluid bypass Important Note: BendPak lifts are supplied with concrete fasteners that meet the criteria of the American National Standard ANSI/ALI ALCTV-(Current). The buyer is responsible for all charges relating to any special regional structural or seismic anchoring requirements specified by any other agencies or codes such as the Uniform Building Code (UBC) or International Building Code (IBC).

Not Yet Reviewed

$9,395.00

On Sale

BendPak LR-1000 Low-Rise Lifts

BendPak LR-1000 low-rise lifts are your solution for quick maintenance and increased productivity when servicing today's passenger cars and light trucks. From tire and brake service … to vehicle detailing and body repair, these lifts will facilitate your work on a wide variety of vehicles. Additional facts and specs: * Low-profile height that accommodates most vehicles, including sports cars, race cars, and larger trucks and SUVs * Single-point safety release make this lift easy to operate and very safe to use * Dropped crossbar in the center provides added vehicle drive-over clearance. Suspension work, oil changes, wheel and brake service, and detailing are easier than ever * Industrial-grade hydraulic cylinder * Solid rubber lift blocks

Not Yet Reviewed

$5,495.00

$5,095.00

BendPak MDS-6EXTF Mid-Rise Open-Center Car Lifts

Using long-wheelbase vehicles as BendPak's point of reference, they designed the MDS-6EXT mid-rise open-center car lifts to accommodate longer lifting points that better reach the extreme edges of the vehicle underbody. Along with the flush-mount MDS-6EXTF, these two extended mid-rise lift models maintain their open-center design, just like their standard length MDS-6LP and MDS-6LPF models. The MDS-6EXTF extended-length, flush-mount, mid-rise lifts provide quick-lube stations looking to install a car lift flush over work pits. If your shop wants to be ready for longer-wheelbase vehicles and minimize the lift's footprint, you can't do better than BendPak's MDS-6EXTF mid-rise open-center car lift. Key features: * 6,000-lb. lifting capacity * Open-center design/flush-mount * Adjustable arm assemblies * Solid-steel safety lock bars * Multiple lock positions * Hinge-point with Zerk grease fittings * Low-profile design * Rubber blocks included * Removable ramps

Not Yet Reviewed

$8,195.00

Hughes Performance Muscle Car Transmission Packages

Hughes Performance Muscle car transmission packages are designed and built to give customers the option to choose the transmission and converter package best suited for their needs. The transmission packages come complete with everything you need—transmission, converter, transmission cooler, transmission fluid, and more. So, whether you have a radical cam in your hot rod, or need to haul or tow a heavy load, Hughes Performance offers high-quality transmission packages to match your application needs. Note: Contents of kits vary based on transmission type and your vehicle.

5.0 out of 5 stars ( 1 )

$5,061.99

Heidts 1970-74 Mopar Challenger and Barracuda PRO-G Independent Front Suspension Kits

Heidts 1970-74 Mopar Challenger and Barracuda PRO-G independent front suspension kits are a comprehensive, bolt-in upgrade designed to replace the stock factory torsion bar suspension with a modern, high-performance, double A-arm front suspension system. Specifically engineered for 1970-1974 E-body vehicles, these kits improve handling and cornering using adjustable coilovers, rack-and-pinion steering, and Wilwood brakes. Key features: * Complete system: Hub-to-hub kit includes a new crossmember, tubular control arms, spindles, and power rack-and-pinion steering * Performance upgrades: Features QA1 adjustable coilover shocks and springs for height and ride tuning * Improved geometry: Designed to eliminate bump steer and allow for significant caster and camber adjustments * Braking: Comes standard with 11 in. Wilwood rotors and 4-piston calipers * Engine fitment: Accommodates Mopar small block, big block, and Gen 3 Hemi engines, usually requiring a rear-sump oil pan * The kit is tailored to bring modern handling capabilities to classic Mopar muscle cars, reducing unsprung weight and increasing overall torsional rigidity

Not Yet Reviewed

$7,623.00

EMAX Industrial Plus Silent Air Piston Compressors

EMAX Industrial Plus Silent Air piston compressors are quiet. The most common complaints about compressors are their high noise levels. EMAX Silent Air units not only still the noise, but they also do it with a big cfm output and lower rpm. Featuring their Whisper 100 system installed on the back of the tanks, stationary compressor dB ratings are reduced by as much as 25 percent. The Whisper dissipates compressor intake noise by channeling intake air through a series of baffle plates and prefilter media inside the silencer cabinet. Piston intake noise is trapped and dissipated within the silencer structure; plus, it also provides secondary filtration for cleaner air. Industrial Plus Silent Air piston compressors are designed for up to 50,000 hours of commercial or industrial use with proper maintenance. At the core of these extremely durable compressors are super-quiet pumps featuring cast iron crankcases, precision-balanced cast iron crankshafts, and high-quality stainless steel roller bearings to ensure smooth, efficient operation. For long life and rebuildability, EMAX adds steel connecting rods with replaceable rod bearing inserts, removable cast iron cylinders and cylinder heads, disc intake and exhaust valves, and cast iron flywheels with a built-in fan. These bigger low-rpm pumps have a larger bore and stroke, so you get big cfm output with reduced friction and heat buildup. All EMAX Industrial Plus compressors have low-rpm motors (1,750 rpm). Because of their higher torque factor, compared to the 3,450 rpm motors most manufacturers use, they run much cooler. They also yield low harmonic distortion, provide much higher torque in cold weather starting, and require less electricity to start. Other features include big 1 3/8 in. output shafts, large starting and running capacitors, and dynamically balanced armatures. Their 15 Service Factor means the motors can be pulled 15 percent over full load. Depending on the application, many Silent Air piston compressors feature totally enclosed, fan-cooled (TEFC) motors that keep harmful dust and particulates out of the motor. This allows them to be used in dusty commercial and industrial environments without worrying about maintenance. They have 100 percent copper windings with pre-wired magnetic starters (necessary on any motor over 15 amps). These are high-quality, name brand, premium efficiency motors that meet all UL and CSA requirements. Some lower horsepower models are equipped with name brand, open-drip (OPD) motors. The running and starting windings on these motors are all 100 percent copper-wound for premium efficiency, reliable performance, and durability. These units also meet all UL and CSA requirements and include pre-wired Condor combination starter and pressure switches with actuation-type diaphragms. EMAX Industrial Plus Silent Air piston compressors also feature: * Head unloaders allow for load-less starting and can help cool the pump in high-duty cycle applications * Built-in inter-coolers and after-coolers * Raised-pump mounting platforms that open the underside of the crankcase to cooling air flow * Automatic belt tensioners for much easier and quicker adjustments and alignment * Selectable continuous-run or automatic start/stop operation to maximize performance and reduce wear * OSHA-approved belt guards for your safety * ASME code-compliant tanks * Dual-timer automatic tank drains eliminate maintenance * Taper lock 2-groove pulleys * Dual 2-groove belts for long life and low vibration * Extended tank water drain pipes plumbed to the front with 1/4 in. ball valve handles * 100 percent brass check valves, safety valves, and ball valves * Top-quality plumbing fittings

4.75 out of 5 stars ( 16 )

$5,356.30

—

$5,892.10

American Powertrain Tremec T-56 Magnum Manual Transmissions and Installation Kits

American Powertrain Tremec T-56 Magnum manual transmissions and installation kits are designed to withstand up to 700 lbs.-ft. of torque. Their gears feature substantially increased face widths and 2-piece laser-beam welded construction, allowing for greater control of the tooth angles, pitch, and alignment. The transmissions also include a bolstered one-piece countershaft to resist distortion, and a stronger input shaft. Magnum's new synchronizers are built with fine-tooth angles, redesigned shift forks—and an extensively modified transmission case to prevent leaks under high-stress conditions and increase overall power-handling capabilities. Nearly two dozen models are available; choose the kit recommended for your vehicle application. Kits include: * Cryo-hardened steel driveshaft slip yoke with 1330 style U-joint * Mechanical speedometer conversion * VSS wiring harness for electronic speedometer of EFI ECU * Reverse light wiring, weather seal harness, non-polar * Reverse lockout wiring harness * ISO-X ballistic, low-profile transmission mount * Steel roller pilot bearing * White shift knob with black 6-speed shift pattern

Not Yet Reviewed

$5,025.00

—

$5,025.95

On Sale

Ranger R76ATR Tire Changers

Ranger R76ATR tire changers are versatile time-savers. They have tilt-back towers that allow you to work different tire-and-wheel combos without adjusting the duck head, and the swing-arm design with tower assist ensures stiff sidewalls are never a problem. They are easy to operate and rugged enough to stand up to demanding workloads. The large 30 in. capacity turntable features adjustable, hardened-steel RimGuard wheel clamps, providing an internal clamping capacity of 9 in. to 28 in. and external clamping capacity of 10 in. to 30 in. Features: * Traveling drop-center hold-down device * Inflation system * Inflation gauge and air dump valve * Inflation pressure regulator/limiter * Oiler/lubricator * Air regulator * Bead tool/tire iron * Alloy steel mount/demount head * Nylon mount/demount head * Large soap bucket * Soap brush

Not Yet Reviewed

$7,395.00

$6,995.00

On Sale

Ranger RL-8500 Brake Lathes

The revolutionary Ranger RL-8500 combination brake lathes use independent DC servo motors to control the cross feed and spindle feed drives, eliminating the need for complex mechanical gear boxes and transmissions typically found on mechanically-driven lathes. The ruggedly built RL-8500 brake lathes are capable of faster, easier, and more accurate rotor/flywheel and drum/flywheel resurfacing than any other brake lathe in its class. Infinitely adjustable feed rates allow you to easily modify cut speeds with the simple turn of a dial. Now you can reduce or increase the cut time for the best finish results, whether you're speeding through an initial rough cut or a single-pass micro-finish. These Ranger lathe packages include the lathe, a sturdy bench and large tool storage backboards, so you can hang all your adapters within close reach. One of the common problems that plague other brake lathes is the vibration and chatter transfer that directly affects the tool-tip and leaves an imperfect cut on the machined surface. The RL-8500 brake lathes by Ranger are specifically designed to address this issue by eliminating the need for gear-driven mechanical drives and variable-speed transmission devices.

Not Yet Reviewed

$11,395.00

$10,790.00

On Sale

Ranger RP-50FC Oil Filter Crushers

Need a great way to crush used oil filters so they can be easily disposed of? Ranger RP-50FC oil filter crushers are perfect for you. Environmental agencies all over the world require oil filters be crushed before they are recycled to ensure all of the oil has been removed. Harnessing 50,000 lbs. of crushing power the RP-50FC units make quick work of both car and truck filters, crushing them to about 20 percent of their original height and squeezing out 95 percent of the residual oil in the process. Oil is gravity fed out the bottom of the machine through a transparent downspout tube into the container of your choice (up to a 55 gallon drum) to recycle later. The automatic cycle allows you to press a button and walk away, the machine will do the rest. They are capable of handling automotive and heavy-duty filters up to 15.250 in. long and 6 in. in diameter. Save on waste disposal and storage space with the Ranger RP50FC 25 ton oil filter crushers.

Not Yet Reviewed

$5,895.00

$5,595.00

On Sale

Ranger RS-750DS Parts Washers

The Ranger RS-750DS parts washers have a 53-gallon tank and come with the latest features for rapidly degreasing the biggest car parts around—making it the ultimate answer to degreasing car parts of any shape or size. Built to last, these stainless steel spray wash cabinets allow for more space to fit more parts in at a time. With the extra room, you can clean and degrease automotive parts faster than ever before! Features and specs: * 53-gallon tank with heavy-duty stainless steel construction and powdercoat finish to resist rust * Commercial-grade pump/motor combination provides washing power—made of high-quality parts like the rust-resistant stainless steel impellers—while the centrifugal pump does all the heavy lifting (a protective covering comprised of 100 percent ductile cast iron and silicon carbide seals keep the machinery inside safe and dry) * Wash cabinet is sealed with a leak-proof neoprene door—creates an edge-to-edge seal and prevents water and steam from escaping to create better water retention which improves cleaning efficiency * Heated cabinet with adjustable set point thermostat allows you to adjust the heating range up to 175 degrees F * Safety switch and timer dial for a functional machine that is both safe and efficient * A nickel-based, alloy-sheathed heater element is specifically designed for heated parts washing—ensures that your parts washer is hot and ready to go at the press of a button * Contamination-proof interior welds prevents even microscopic debris from getting into the recirculating tank to help ensure nozzles and pumps remain unclogged, redirecting unwanted debris to the trap and filter * Stainless steel nozzles are resistant to wear and clogging—sprayer nozzles have a sharply articulated spray grid to provide a powerful wash, blasting away dirt and grime * Full opening octagonal door and stainless steel handles * Dual water heaters for quick startup—water temperature is raised within seconds thanks to the dual water heaters that keep water primed and ready at all times * High-power spray jets clean parts fast—attacks dirt and grime from all angles, ensuring an even powerful wash * Automatic low water shutoff feature cuts the power when the water level gets too low, saving your dual heaters from any potential damage—switch is made from an industrial-grade stainless steel float located in the detergent tank that rises and falls with the water level * Stainless steel oil skimmer—separates oil and grime from the water which further increases the longevity of your detergent solution (oil is directed outside the cabinet into a holding container for disposal) * Removable tree rack and components basket is essential for small parts and for maximizing parts washing space, the tree rack installs and removes easily instantly extending tank space and provides space for smaller parts like bolts, nuts, and screws * Convenient tank drain pipes help you maintain your spray wash cabinet by preventing debris from accumulating on the bottom * Moveable filter basket traps any particle larger than 1/8 in., so you can be sure that your tank water remains free of any build up that could cause harm and can be easily removed to gain access to the cleansing tank for maintenance * Non-marring casters make maneuvering even this bulky piece of equipment a breeze and the urethane casters ensure that your floor remains safe * Convenient drain tank—large built-in pipe drains that redirect and remove sludge from the parts washer floor, which helps keep the washer clean and functioning smoothly * A friction-drive turntable is the system behind the parts washer, and it cuts out the risk of motor damage by preventing jams that might otherwise occur within the cabinet and tank

Not Yet Reviewed

$15,895.00

$15,295.00

iDEAL Equipment Open Front Paint Spray Booths

iDEAL 'A-Frame' Open Front Paint Spray Booths are economic, commercial-grade open front units designed to provide optimal 'airflow' with superior lighting for high-quality spray painting and finishing applications. They're a great solution for industrial batch-type and automated production-type finishing systems. Air flows through the open front section of the booth, then passes through the work area toward the rear of booth into the filtered exhaust chamber. Filtered exhaust air is then drawn through the exhaust plenum and discharged upward through the exhaust fan and ducting. The booths are easily installed with heavy-duty, precision-punched 18-gauge panels, allowing for quick nut and bolt assembly. Each booth is standard with a bright white powdercoat finish, deluxe control panel, premium exhaust filters, hinged glass light fixtures, and high-quality tube-axial exhaust fan. Features and specs: * Commercial-grade design for optimal airflow and lighting coverage * Deluxe control panel included * White powdercoat panel finish (inside and outside) * Heavy-duty, precision-punched 18-gauge panel construction * Convenient 5/16 in. bolt and serrated lock nut assembly * UL Listed Dayton 24 in. tube-axial exhaust fan with spark-resistant fan blades * NEMA rated 2 hp, 3 phase, 230/460 V AC 60hz motor standard * Premium AFC exhaust filters * LDPI industrial light fixtures with inside access hinged glass door * (2) LPDI industrial (CLS1 / Div. 2) light fixtures – UL and ETL (Groups A, B, C, and D) * True 'daylight color' with GE T8 48 in. fluorescent lamps 32 watts, 2900 lumens, 5000K * Optimal airflow with CFM 7,983 at .5 static pressure * Inside dimensions: 13 ft. wide x 8 ft. 6 in. high x 7 ft. 6 in. deep * All assembly hardware, manometer, and sealant included * Meets or exceeds all applicable OSHA and HFPA 33 regulations * Easy to install, operate, and maintain

Not Yet Reviewed

$9,050.00

Heidts Superide Independent Front Suspension Kits

Independent front suspension gives you twice the ride of a new 4-link dropped axle at a comparable cost. These Heidts Superide independent front suspension packages have been engineered for a correct, safe ride, while providing the ultimate stance. They feature a one-piece crossmember with upper control arms that clear the fenders, and their 56 in. hub-to-hub tread width gives you the narrow look without any tire-to-fender clearance problems. The packages include specially designed one-piece 1045 heat-treated alloy steel spindles to give you the lowest possible ride available, the high-tech appearance you want, and assurance of the right geometry, right fit, and a great ride. Nearly a hundred packages are available to fit applications from the 1920s and up. Components include: * Heidts one-piece crossmember * Superide spindles * Tubular upper and lower control arms * Front disc brake kit with 11 in. diameter brake rotors and 4-piston brake calipers * Manual rack and pinion steering, rear mounted * Billet single adjustable coilover shocks with silver powdercoated springs

Not Yet Reviewed

$5,213.00

—

$6,154.00

Heidts Superide II Independent Front Suspension Kits

Enjoy driving your fat-fendered cruiser with the smooth ride and handling of independent suspension. Heidts Superide II independent front suspension kits utilize a Mustang II spindle to allow for a front mount rack and pinion unit, making engine installation much easier. The upper control arms use threaded adjusters for the wheel alignment. Unlike eccentric adjusters, they will never slip or lose alignment when hitting bumps in the road. Dozens of packages are available for applications from 1935 and up. Components include: * Heidts 3-piece crossmember * Mustang II stock spindles * Tubular upper and lower control arms * Front disc brake kit with 11 in. diameter brake rotors and 4-piston brake calipers * Manual rack and pinion steering, front mounted * Billet single adjustable coilover shocks with silver powdercoated springs

4.0 out of 5 stars ( 1 )

$5,317.00

—

$5,854.00

Heidts 1962-67 Nova Superide II Independent Front Suspension Kits

Enjoy driving your fat-fendered cruiser with the smooth ride and handling of independent suspension. Heidts Superide II independent front suspension kits utilize a Mustang II spindle to allow for a front mount rack and pinion unit, making engine installation much easier. The upper control arms use threaded adjusters for the wheel alignment. Unlike eccentric adjusters, they will never slip or lose alignment when hitting bumps in the road. Dozens of packages are available for applications from 1935 and up. Components include: * Heidts 3-piece crossmember * Mustang II stock spindles * Tubular upper and lower control arms * Front disc brake kit with 11 in. diameter brake rotors and 4-piston brake calipers * Manual rack and pinion steering, front mounted * Billet single adjustable coilover shocks with silver powdercoated springs

Not Yet Reviewed

$6,154.00

Ranger R26FLT Super-Duty Truck Tire Changers

Ranger R26FLT Super-Duty truck tire changers are efficient tools for changing tubeless truck, agricultural, and off-road tires from 14 in. to 26 in. diameter in just minutes. A portable remote control unit allows multiple functions for time-saving convenience. Ranger explored all aspects of truck wheel service to devise the fastest floor-to-floor service, making your job easier and more profitable. The tire changers are built with forged, hardened, and ground components designed to resist scoring, grooving, and wear. This equipment is simple to operate, and engineered for speed and safety. Features include: * Super-duty electric motor and hydraulic drive for superior torque and wheel-holding power * Self-centering hydraulic clamping chuck * Heavy, tapered roller bearings and a dual-direction hydraulic motor provide smooth torque * Quick positioning and locking mount/demount arm * Hydraulic sled carriage for positioning, bead loosening, mounting, and demounting procedures * Single-piece frame for superior rigidity * Hydraulically operated spreader-type jaws ensure secure clamping of virtually all rims and off-road style wheels * Massive chuck spindle handles the heaviest loads * Sturdy spindle, chuck, and mount/demount head hydraulically rotates, raises, and lowers with simple operator controls * Very gentle on over-the-road tires and tubeless tires mounted on aluminum wheels

Not Yet Reviewed

$12,795.00

Ranger R80EX Tire Changers

If you're looking to save time, the Ranger R80EX tire machine is a must-have for busy shops. The R80EX tire changers feature a dual-assist, tilt-back tower design, so it's outfitted with the industry's best and most powerful tools. With this equipment, you get the classic rugged reliability Ranger is known for, plus dozens of standard features. A multi-profile traveling drop-center tool, top bead assist rollers, dual lower bead lifting discs and a nylon non-marring wheel restraint device are important tire shop tools designed to dramatically reduce effort, increase safety, and help minimize operator fatigue. If your shop life demands a tool that will generously handle round-the-clock use and abuse, the R80EX delivers! Key features and specifications: * Sealed electronic components for air-tight, dust-free, and contamination-proof protection of terminal leads * Updated electric motor features the best of proven technologies, including rugged copper rotor construction, high-quality bearings, thermal-cool epoxy insulation and durable rolled steel frames * Balanced flywheel helps machine run smoothly, reduces vibration, and helps minimize associated stress on other machinery components * Table clamping system * Dual pneumatic cylinders * Simple foot-pedal control—durable forged steel (instead of cast iron) and features multi-link rod connections for non-binding plunger movement and precise bilateral control * Adjustable RimGuard wheel clamps feature internal/external multi-teeth jaws * Variable clamp positioning makes wheel service simple, perfectly controlling the wheels when clamping them * Adjustable bead loosener system and pneumatic blade—bead loosener control single-lever control on shovel handle * Bi-lateral power-controlled bead loosener features single-lever control on the shovel handle—this ergonomic design eliminates traditional foot-pedal controls that often force technicians into unbalanced working stances when loosening beads * Dual left and right power assist towers * Tower design tilt-back—provides greater clearance and access for tire removal and inflation * Pneumatic-lock tool head stays positioned on the tower return for instant set up for like sets of tires and wheels * Upper bead assist roller * Standard/Dual power-drop * Traveling drop-center hold-down device * Wheel centering tool/Inflation restraint device * Turbo-Blast bead seating system * Tool tray/Bin storage * Inflation gauge with integrated air dump valve * Inflation pressure regulator/limiter * Water filter/Oiler/Lubricator * Air regulator * Tire iron/Bead lever tool * Large soap/Lubricator bucket * Brush * Motorcycle turntable clamps (optional)

Not Yet Reviewed

$11,095.00

On Sale

Ranger RL-8500XLT Brake Lathes

Ranger RL-8500XLT brake lathes feature an extended capacity spindle and can turn a drum that's up to 10 in. deep. The longer spindle and the relocated rear bushing provide the arbor with enough support to handle your heaviest drums, rotors, and flywheels. Durably crafted, RL-8500XLT brake lathes resurface brakes quicker and more precisely than any other lathing unit on the market today. They feature unlimited feed rate settings, allowing the user to modify resurfacing rates with an easy turn of the dial. Now you can decrease or amplify the cut duration for the perfect finish, whether you're rushing through the first rough cut or performing a single-pass micro-finish. Features include: * RL-8500XLT uses precision electric DC servo motors designed to meet the demanding requirements of industrial motion control * Quick-Change Adapter-Plus system with built-in springs eliminates the need for conventional bell clamps and cones * Works on all cars or trucks, both foreign and domestic, with hubless drums, rotors (center hole sized 2 5/32 in. to 4 in.) and composite rotors (center hole sized 4 in. to 6 1/4 in.) * Precision twin cutter tools and a quick drum-to-rotor changeover

Not Yet Reviewed

$13,095.00

$12,495.00

Parts and Accessories