Availability
Showing In Stock Items. Show All 20 Items.
Lingenfelter PWM output module controllers provide the PWM speed control signal needed to operate variable speed OEM and aftermarket DC brushless cooling fans and fluid circulation pumps. The speed is controlled based on a temperature sensor input signal or a simple switched input for on/off type control. They can be used to control primary engine cooling fans, auxiliary engine cooling, or other fluid cooling fans, or to control variable speed pumps for engine coolant, intercooler fluid, or other related fluid circulation applications. Features: * Two sets of easily adjustable device control switches * Start temperature option sets the initial on temperature for the devices * Maximum output temperature option sets the temperature for the maximum device speed * Module provides a linear output speed control between these two settings * The same switches are also used to set speed percent in direct device speed control mode * Can be used to control multiple devices when all devices are the same input type * Override input available for AC system related activation, manual override, etc. * High setting output indicator to trigger a warning light or auxiliary systems * 0 to 5 V output of temperature sensor or fan/pump target speed percent * Send temperature or pump speed to an ECM, data acquisition system, or a gauge * Provides a wide temperature control range allowing these fans to be used in a broad range of applications without having to purchase different sensors or modules for each application * Uses readily available and durable OEM or common PT200 platinum RTD sensors * Activation is adjustable from 0 to 350 degrees F in 10 degree increments for IAT, ECT, TFT * Activation is adjustable from 0 to 1,800 degrees F (0 to 990 degree C) in 10 degree increments for EGT/RTD sensor * Speed percentage adjustable in 1 percent increments, when in speed control mode * High-temperature, glass-filled nylon enclosure and fully epoxy potted circuit board for increased durability
( 6 )
$227.95
Lingenfelter temperature-based relay controllers are designed to control relays based on temperature sensor readings. They can be used to independently activate two relays to control fans, pumps, or other devices. These relays can also be used to activate intercooler water spray based on air temperature or alcohol injection based on intercooler temperature. Lingenfelter temperature-based relay controllers reduce noise and increase component life in your auxiliary cooling systems.
Not Yet Reviewed
$180.45
Consider these brackets to be convenient problem-solvers! Lingenfelter Performance Engineering idler pulley relocation brackets enable you to install a larger-diameter supercharger pulley on the harmonic balancer or damper, if the stock idler does not have enough clearance. Each kit includes a black hard-coat anodized 6061 billet aluminum bracket and stainless fasteners. These brackets are designed to work with the stock idler pulley and can also be used with certain Lingenfelter idlers.
( 3 )
$113.95
The Lingenfelter Performance Engineering STOV-004 is a vehicle speed-based switch that can be used to enable or disable devices based on vehicle speed—much like an RPM switch or RPM window switch, but instead based on vehicle speed. The STOV-004 also provides a 0-5 volt analog output corresponding to vehicle speed that can be used to provide a vehicle speed signal to many other add-on devices. These switches can accept the vehicle speed output signal from most engine control modules and can also connect directly to many common speed sensors. The Lingenfelter STOV-004 can also provide a stage/gear shift output for boost controllers and other devices that need to see a gear shift position switch output to change stages. Product features: * Accepts a wide range of pulse count frequencies from 100 to 60,000 pulses per mile (PPM) * Works with ECM output signals and stand-alone Hall effect-type speed sensors * Easy-to-use vehicle speed learning mode using push-button switch in the back of the module * Set the PPM count even when you do not know the PPM configuration of the vehicle * Built-in vehicle speed sensor signal pull-up resistor that is enabled by a DIP switch setting inside the back cover for applications that require a pull-up resistor * Simplifies wiring * Easy to adjust high and low vehicle speed settings via four front-mounted 10-position switches * Provides switched outputs or window switch outputs based on vehicle speed * Provides ECM/PCM vehicle speed frequency to analog voltage conversion Available output types: * Normally ON ground * Normally OFF ground * Normally ON +12vdc * 0-5vdc/0-250 mph linear analog output Stage/gear shift output mode works with multi-stage boost and nitrous controllers including: * Turbosmart eBoost2 * NLR AMS1000 * Leash Electronics Boost Leash Gear-Based controller Benefits: * Easily adjustable activation point in 1 mph increments * Enable nitrous or an additional stage of nitrous-based on vehicle speed * Enable a boost controller for increased boost above a certain vehicle speed * Disable fans above a certain vehicle speed * Lock a torque converter clutch above a certain vehicle speed * Disable a 2-step once the vehicle is moving so that it does not activate on each gear change
( 2 )
$140.55
With Lingenfelter Performance Engineering LS engine valve spring compressor tools, in-car valve spring changes have never been easier for the home hot rodder. Designed to work on C6, C5, F-bodies and all LS1 powered vehicles, they are crafted of billet aluminum and incorporate a steel roller bearing trunion for ease of operation. They work with any 3/8 in. hand ratchet; simply add a 3/8 in. extension for valve springs which are difficult to reach (under cowl), and will work on factory conical valve springs, along with aftermarket 1.25 O.D. spring/retainer sets. For anyone changing camshafts with more than .500 valve lift, Lingenfelter Performance Engineering LS engine valve spring compressors are a must!
( 3 )
$103.50
Install an earlier-style camshaft with a 3-bolt sprocket using Lingenfelter 3-bolt camshaft installation kits. Newer Chevy engines have a single-bolt camshaft sprocket design with a spring-loaded chain tensioner, so you will need these kits. They will include a 3-bolt sprocket, three camshaft bolts, a chain damper, and special bolts with sleeves required for the install.
( 3 )
$113.95
Make boost adjustments by running Lingenfelter Performance Engineering supercharger pulleys. These aluminum pulleys are black powdercoated for added durability and lasting good looks. They are offered in a choice of smaller sizes to help you get the percentage of overdrive you're looking for. The proper amount of boost is good. Look to Lingenfelter Performance Engineering supercharger pulleys for the right choices for your application.
( 5 )
$145.30
—
$170.95
Lingenfelter Performance Engineering idler pulleys correct belt length when changing supercharger pulleys or harmonic balancer sizes. They are made from anodized aluminum and can be used on many supercharged engine applications.
( 1 )
$180.45
Increase boost with Lingenfelter Performance Engineering overdrive balancer pulleys. They are crafted from lightweight but strong aluminum and are black anodized for lasting durability and good looks. These pulleys are available in several sizes to use with your harmonic balancer. Overdrive your supercharger to get the boost you're looking for with Lingenfelter overdrive balancer pulleys.
( 3 )
$209.90
Lingenfelter Performance Engineering LSX valve springs are premium single beehive-style valve springs. They are offered in sets of 16 and can be used with stock LS valve spring retainers.
Not Yet Reviewed
$199.45
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
