Free Shipping on Orders Over $125 at Summit Racing

Summit Racing™ Gen III Hemi MDS Delete Kits

Wanting to deactivate the Multi-Displacement System of your Hemi vehicle will require a few things, including a non-MDS camshaft and components. Summit Racing™ Gen III Hemi MDS delete kits are offered in versions designed for engines with or without Variable Valve Timing (VVT). They contain premium components (except programmer) to help you complete the job. Each Summit Racing™ delete kit will include a head gasket set, timing cover gasket, non-MDS lifters, replacement cylinder head fasteners, non-MDS solenoid plug, and camshaft, along with valve springs and/or camshaft phaser limiters. Choose the combo designed for your vehicle.

4.5 out of 5 stars ( 2 )

$1,301.90

—

$1,733.79

Melling AFM/MDS Delete Combo

Melling offers their engine cylinder deactivation kits for converting active fuel management engines to non-active fuel management versions. These AFM (active fuel management) or MDS (multi-displacement system) delete combos include a variety of components to help complete the changeover. Order the Melling AFM/MDS delete combo best suited for your application. Each kit includes: * MDS delete camshaft (1) * Non-MDS hydraulic roller lifters (16) * Lifter guides for Non-MDS engines (4) Application dependent components include: * AFM/MDS solenoid plugs (4) * Camshaft thrust plate (1) * Variable Valve Tming (VVT) oil control valve (1) Notes: * When installing a delete cam, the active fuel management lifters must be replaced using non-active fuel management lifters. * The valve lifter guides used in non-active fuel management engines differ from those used in active fuel management engines and must be replaced for this application. * The AFM/MDS solenoids must be replaced using non-MDS plugs. * The vehicle engine control module/powertrain control module must be reprogrammed to turn off the active fuel management system in the operating software. * Pushrod length must be checked during installation to verify the correct length.

4.5 out of 5 stars ( 6 )

$640.99

—

$1,394.99

COMP Cams HRT Max Power Master Camshaft Kits

COMP Cams HRT Max Power Master camshaft kits take the guesswork out of choosing the right valvetrain-upgrade package to achieve your desired performance with your Dodge Gen III Hemi. These Max Power kits feature the "low shock technology" of COMP's HRT camshafts with lobe profiles designed to maximize horsepower and improve stability at higher rpms. The profiles are also easier on valve springs, enhancing durability and reducing load loss. By dyno testing with many combinations of valvetrain components, COMP Cams' engineers have created these more complete, perfectly matched engine camshaft packages for your Hemi application in three different stages of performance. COMP HRT Max Power MK-kits include: * HRT Cam * Lifters * Pushrods * Conical or Beehive springs * Steel retainers * Locks * Spring seats * Valve seals * Phase limiter (VVT Hemi kits only)

4.17 out of 5 stars ( 6 )

$1,839.95

McLeod RST Street Twin Clutch Kits

Intended for high-horsepower street fans, the McLeod RST Street Twin clutch kits are economically priced twin disc clutches that use your existing flywheel. Able to handle up to 800 hp, the RST Street Twin clutches remain completely street-drivable. The organic lined clutch discs provide smooth engagement with a soft pedal effort, making these clutch kits ideal for the street performance enthusiast. (For select vehicles where these clutches are not adaptable to your existing flywheel, a new flywheel is included in the kit.) Here are some additional features of the McLeod RST Street Twin clutch kits: * Alignment tool included * Lighter-than-stock pedal feel * Will bolt to factory flywheel * CNC-machined and anodized flywheel adapter ring * Organic disc facing for smooth and even clutch engagement with excellent release qualities * Low rotating mass for quick revs * Blanchard ground floater with multiple straps to reduce noise for streetability

4.51 out of 5 stars ( 87 )

$925.00

Corsa Resonator Delete X- Pipe Kits

Open up the sound of your cat-back exhaust with Corsa resonator delete X-pipe kits. High-quality mandrel-bent stainless steel tubing is used to create these kits to replace restrictive factory pieces. You do not need a whole need system to get the desired sound. All you need is Corsa resonator delete X-pipe kits.

Not Yet Reviewed

$771.99

Hays Street 650 Clutch Conversion Kits

Hays Street 650 clutch conversion kits are designed to handle highly modified engines up to 650 hp naturally aspirated (600 hp for forced induction and nitrous combinations). The new 26-spline versions work in conjunction with a modern 5- or 6-speed transmission swap. These are true street/strip clutches for spirited high performance driving or frequent track use. The high performance dual-friction disc utilized in the Street 650 has an upgraded spring hub with heavy-duty damper springs to handle greater shock loads versus a standard damper spring. The disc features a sintered metallic friction surface and an organic friction surface. It does a great job at dissipating heat and fighting the slippage found in ordinary discs, along with providing the smooth engagement characteristics of a street-style clutch. These conversion kits also provide an upgraded heavy-duty pressure plate to round out the performance clutch. The Street 650 is a great choice if you visit the track often. Order the model recommended for your vehicle application. Features and benefits: * Upgraded damper springs deliver up to 30 percent more clamping pressure than stock OE clutch * Dual-friction disc offers the best of both worlds—smooth engagement and excellent holding capacity * All Street 650 clutch kits come complete with pressure plate, disc, throwout bearing, and alignment tool

4.67 out of 5 stars ( 6 )

$578.95

—

$716.95

Holley Sniper 2 EFI Fuel Injection Upgrade Kits

Want to make the switch from the original Sniper EFI to Sniper 2 and don't want to rewire your system? The new Holley Sniper 2 fuel injection upgrade kits are designed to do exactly that! Included with each Sniper 2 plug-and-play upgrade system is an adapter solution that connects your existing Sniper EFI wiring harness to a Sniper 2 throttle body in minutes. Simply remove your Sniper EFI throttle body from the intake manifold, unplug all connectors, reinstall the Sniper 2 throttle body, and plug the Sniper EFI 2 adapter harness into your existing main harness. Cycle your ignition key, run a fresh wizard on the display of your choice, and enjoy the benefits of Sniper 2 EFI. The #1 EFI conversion system just got better! Introducing Sniper 2 EFI—a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion simpler, more reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will self-tune with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Four total upgrade kits are available: polished and black, with or without external fuel pressure regulator (required for Sniper 2). Upgrade kit features: * Update your Sniper EFI to the new, improved Sniper 2 in less than one hour! * Eliminates the need to rewire your existing installation; one step, plug-and-play upgrade to a Sniper 2 * Improve your ride with the Sniper 2, including wireless connectivity, smooth throttle feel, improved RF resistance, and a hidden wiring harness. * Reuses existing coolant temperature and oxygen sensors * Female -6 AN O-ring fittings for a tight seal * Overall height is only 3.280 in. to fit under most hoods * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI of regulated fuel supply * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Sniper 2 is part of the Sniper EFI complete ecosystem * Available with fuel system kits: that include an adjustable external regulator, fittings, and a 3 ft. section of fuel hose, allowing you to easily mount your regulator in the engine bay Additional NEW features: * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

3.82 out of 5 stars ( 22 )

$1,024.95

—

$1,449.95

BluePrint Engines Pro Series Mopar 426 C.I.D. 872 HP EFI Deluxe Dressed Long Block Crate Engines

BluePrint Engines Pro Series Mopar 426 c.i.d. EFI Deluxe dressed long block crate engines feature Gen III Hemi Apache aluminum cylinder heads—and can generate up to 872 hp and 764 lbs.-ft. of torque. These engines are available with a polished or black anodized accessory drive pulley kit. --- BLOCK: NEW "BGE" Hellcat / Apache engine block 4-bolt main 4.090 in. bore One-piece rear main seal Compression ratio: 10.48:1 --- ROTATING ASSEMBLY: Forged steel crank 4.050 in. stroke 6.125 in. connecting rods Forged pistons Internal balance - front Internal balance - rear --- CYLINDER HEADS: Gen III Hemi Apache aluminum cylinder heads 73cc chamber 2.140 in. intake/ 1.650 in. exhaust valves --- CAM SPECS: Hydraulic roller cam .610 intake/ .611 exhaust lift 231 intake/ 255 exhaust duration at .050 – 113 degrees LSA --- IGNITION TIMING: Controlled by ECU --- ALSO INCLUDES: Whipple 3.0L supercharger Supercharger fluid reservoir Hellcat throttle body Harmonic balancer Muscle car style - mid sump swap oil pan Spark plugs and coils Timing cover Valve covers Water pump Installed complete front accessory drive: water pump, alternator, power steering, A/C, all belts and pulleys Holley Terminator ECU controller kit and wiring harness All sensors required for engine to run --- NOTES: Features 2013+ 58X reluctor wheel 2009+ crankshaft spacing 2009+ car timing cover VVT locked out MDS – eliminated ** Engine Accessory Specifications: These BluePrint engines were dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet. -- Fuel Delivery Type: Whipple 3.0L supercharger -- Spark Plug: NGK 5107 -- Spark Plug Gap: .025 in. -- Harmonic Balancer: Non-Weighted -- Flex Plate/ Flywheel: Non-Weighted -- Stall Converter: 2500+ -- Intake Manifold: Supercharger -- Fuel Recommendation: 91 - 93 Octane -- Timing: Controlled by ECU -- Firing Order: 1-8-4-3-6-5-7-2

Not Yet Reviewed

$27,799.00

Ridetech Ridepro E5 Ride Height Sensor Kits

Ridetech Ridepro-HP Ride Height sensor kits upgrade your existing Ridepro E5 pressure-based system. They work together to deliver the ultimate air suspension management systems measuring both pressure and ride height accurately. With the addition of Ridepro-HP, ride height and spring balance (loads) are established by comparing the position of the ride height sensor to the air pressure within each air spring. Your car is leveled with no cross loading, which is especially important for dynamic driving scenarios where quick transitions occur, such as high performance driving, sudden directional changes, and panic stops. Ridetech complete Ridepro-HP kits include and feature: * Four ride height sensors * Four ride height sensor linkage kits * Group harness * 1/4 in. sensor bolts with Nyloc nuts and flat washers * Mounting tabs, heat shrink tubes, and installation guide * Easy installation * Heavy-duty ride height sensors * Bendable linkage rods with rubberized rod ends * Weatherproof connectors and wiring harnesses

2.0 out of 5 stars ( 1 )

$695.00

BluePrint Engines Pro Series Mopar 426 C.I.D. 610 HP EFI Deluxe Dressed Long Block Crate Engines

BluePrint Engines Pro Series Mopar 426 c.i.d. EFI Deluxe dressed long block crate engines feature Gen III Hemi Apache aluminum cylinder heads—and can generate up to 610 hp and 525 lbs.-ft. of torque. The engines are available with a polished or black anodized accessory drive pulley kit. --- BLOCK: NEW OEM Hellcat engine block 4-bolt main 4.090 in. bore One-piece rear main seal Compression ratio: 10.48:1 --- ROTATING ASSEMBLY: Forged steel crankshaft 4.050 in. stroke 6.125 in. connecting rods Forged pistons Internal balance - front Internal balance - rear --- CYLINDER HEADS: Gen III Hemi Apache aluminum cylinder heads 73cc chamber 2.140 in. intake/ 1.650 in. exhaust valves --- CAM SPECS: Hydraulic roller cam .610 intake/ .611 exhaust lift 231 intake/ 255 exhaust duration at .050 – 113 degrees LSA --- IGNITION TIMING: Controlled by ECU --- ALSO INCLUDES: Holley Terminator engine harness Fuel injection Throttle body Harmonic balancer Fabricated intake Manifold Muscle car style - mid sump swap oil pan Spark plugs and coils Timing cover Valve covers Water pump Installed complete front accessory drive: water pump, alternator, power steering, A/C, all belts and pulleys Holley Terminator ECU controller kit and wiring harness All sensors required for engine to run --- NOTES: Features 2013+ 58X reluctor wheel 2009+ crankshaft spacing 2009+ car timing cover VVT locked out MDS – eliminated ** Engine Accessory Specifications: These BluePrint engines were dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet. -- Fuel Delivery Type: Fuel Injected -- Spark Plug: NGK 97408/ LZTR6AP11EG -- Spark Plug Gap: .043 in. -- Harmonic Balancer: Non-Weighted -- Flex Plate/ Flywheel: Non-Weighted -- Stall Converter: 2500+ -- Intake Manifold: Fabricated Aluminum Gen III HEMI -- Fuel Recommendation: 91 - 93 Octane -- Timing: Controlled by ECU -- Firing Order: 1-8-4-3-6-5-7-2

Not Yet Reviewed

$19,399.00

—

$19,499.00

Holley Sniper 2 EFI 650 HP Base Fuel Injection Systems

Holley Sniper 2 EFI Base Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * For applications using a vehicle specific EFI conversion tank and fuel pump, or already having a fuel system capable of the required 55-65 psi, these systems are offered without a pump and fuel lines * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

4.13 out of 5 stars ( 32 )

$1,299.95

—

$1,549.95

Holley Sniper 2 EFI 650 HP Inline Pump Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Inline Pump Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters for before and after the pump, fittings and hardware, cushioned mounting brackets, and an external, inline pump * Can be used with 3/8 in. factory sending units or add a dedicated bulkhead fitting * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

4.33 out of 5 stars ( 21 )

$1,799.95

—

$2,049.95

Holley Sniper 2 EFI 650 HP Inline Pump Fuel Injection Systems

Holley Sniper 2 EFI Inline Pump Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters for before and after the pump, fittings and hardware, cushioned mounting brackets, and an external, inline pump * Can be used with 3/8 in. factory sending units or add a dedicated bulkhead fitting * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

3.64 out of 5 stars ( 25 )

$1,699.95

—

$1,949.95

BluePrint Engines Pro Series Mopar 426 C.I.D. 872 HP Base Long Block Crate Engines

BluePrint Engines Pro Series Mopar 426 c.i.d. Base dressed long block crate engines feature Gen III Hemi Apache aluminum cylinder heads—and can generate up to 872 hp and 764 lbs.-ft. of torque. --- BLOCK: NEW "BGE" Hellcat / Apache engine block 4-bolt main 4.090 in. bore One-piece rear main seal Compression ratio: 10.48:1 --- ROTATING ASSEMBLY: Forged steel crank 4.050 in. stroke 6.125 in. connecting rods Forged pistons Internal balance - front Internal balance - rear --- CYLINDER HEADS: Gen III Hemi Apache aluminum cylinder heads 73cc chamber 2.140 in. intake/ 1.650 in. exhaust valves --- CAM SPECS: Hydraulic roller cam .610 intake/ .611 exhaust lift 231 intake/ 255 exhaust duration at .050 – 113 degrees LSA --- IGNITION TIMING: Controlled by ECU --- ALSO INCLUDES: Whipple 3.0L supercharger Supercharger fluid reservoir Hellcat throttle body Harmonic balancer Muscle car style - mid sump swap oil pan Spark plugs and coils Timing cover Valve covers Water pump Holley Terminator ECU controller kit and wiring harness --- NOTES: Features 2013+ 58X reluctor wheel 2009+ crankshaft spacing 2009+ car timing cover VVT locked out MDS – eliminated ** Engine Accessory Specifications: These BluePrint engines were dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet. -- Fuel Delivery Type: Whipple 3.0L supercharger -- Spark Plug: NGK 5107 -- Spark Plug Gap: .025 in. -- Harmonic Balancer: Non-Weighted -- Flex Plate/ Flywheel: Non-Weighted -- Stall Converter: 2500+ -- Intake Manifold: Supercharger -- Fuel Recommendation: 91 - 93 Octane -- Timing: Controlled by ECU -- Firing Order: 1-8-4-3-6-5-7-2

Not Yet Reviewed

$25,099.00

BluePrint Motorsports Pro Series Mopar 426 C.I.D. 610 HP EFI Base Long Block Crate Engines

BluePrint Engines Pro Series Mopar 426 c.i.d. EFI base long block crate engines feature Gen III Hemi Apache aluminum cylinder heads—and can generate up to 610 hp and 525 lbs.-ft. of torque. --- BLOCK: NEW "BGE" Hellcat / Apache engine block 4-bolt main 4.090 in. bore One-piece rear main seal --- ROTATING ASSEMBLY: Forged steel crankshaft 4.050 in. stroke 6.125 in. connecting rods Forged pistons Internal balance - front Internal balance - rear --- CYLINDER HEADS: Gen III HEMI Apache aluminum cylinder heads 73cc chamber 2.140 in. intake/ 1.650 in. exhaust valves --- CAM SPECS: Hydraulic roller cam .610 intake/ .611 exhaust lift 231 intake/ 255 exhaust duration at .050 – 113 degrees LSA --- IGNITION TIMING: Controlled by ECU --- PS426CTF ALSO INCLUDES: Fuel injection Throttle body Harmonic balancer Fabricated intake manifold Muscle car style - mid sump swap oil pan Spark plugs and coils Timing cover Valve covers Water pump Holley Terminator ECU controller kit and wiring harness All sensors required for engine to run --- NOTES: Compression ratio: 10.48:1 Features 2013+ 58X reluctor wheel 2009+ crankshaft spacing 2009+ car timing cover VVT locked out MDS – eliminated ** Engine Accessory Specifications: These BluePrint engines were dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet. -- Fuel delivery type: Fuel injected -- Spark plug: NGK 97408/ LZTR6AP11EG -- Spark plug gap: .043 in. -- Harmonic balancer: Non-weighted -- Flexplate / Flywheel: Non-weighted -- Stall converter: 2500+ -- Intake manifold: Fabricated aluminum Gen III HEMI -- Fuel recommendation: 91 - 93 Octane -- Timing: Controlled by ECU -- Firing Order: 1-8-4-3-6-5-7-2

Not Yet Reviewed

$17,499.00

Holley Sniper 2 EFI 650 HP Base Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Base Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * For applications using a vehicle specific EFI conversion tank and fuel pump, or already having a fuel system capable of the required 55-65 psi, these systems are offered without a pump and fuel lines * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

4.36 out of 5 stars ( 11 )

$1,399.95

—

$1,649.95

Holley Sniper EFI Stealth 4150 Fuel Injection Systems

Holley Sniper EFI Stealth 4150 fuel injection systems feature four 100 lb.-hr. fuel injectors capable of supporting up to 650 hp naturally aspirated. The Sniper Stealth 4150 ECU is capable of fuel map self-learning and ignition timing control--improving idle stability, drivability, and wide-open throttle horsepower! These systems also include transmission kickdown provisions for GM TH350/400, 200R4/700R4 and Ford C4/C6 applications. The 4150 is available individually or in a complete Master Kit (see contents listed below). ALL Sniper EFI Stealth 4150 systems feature: * Bolt-on 4150 flange carburetor replacement * Throttle body mounted ECU; no extra boxes to mount * Supports up to 650 hp with four 100 lb.-hr. injectors * All of the wiring exits below the rear fuel injector cover—for a completely stealth installation * Timed spark part for vacuum advanced distributors located under the front fuel bowl—for easy access to the distributor * Air entry is machined to fit most stock-style air cleaners with air cleaner locator provisions * Only four wiring connections required (battery +, battery -, switched ignition, and RPM) * External fuel pressure regulator required, set to a base pressure of 58.5 psi, such as 12-886 * Integrated ignition timing control * High-resolution full-color touch screen for initial setup, tuning, and gauge displays * Simple calibration wizard (answer a few questions about your engine and it creates the base map, then starts tuning on its own); NO laptop required * Self-tuning ECU means you don't have to be a computer/tuning wiz to have EFI * The included genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learn * OEM-style TPS/IAC and fuel pressure regulator, for years of dependable service * Included clamp-on oxygen sensor kit for 2.25 in. exhaust ensures a leak-free oxygen sensor installation, with stainless steel T-bolt clamps and a stainless steel (weldable) oxygen sensor flange * Available in three finishes: shiny, ceramic black, and classic gold MASTER KITS also include complete fuel system with an external fuel pressure regulator preset to 58.5 psi, 20 ft. of 3/8 in. Vapor Guard fuel hose, fuel pump, filters, necessary hardware, and bulkhead fitting to return fuel into the tank.

4.27 out of 5 stars ( 41 )

$1,499.95

—

$1,849.95

Clearance

Kooks Headers Exhaust Systems

Kooks Headers offers a variety of exhaust systems designed for specific vehicles. They feature large diameter 304 stainless steel construction with smooth-flowing mandrel-bent tubing for maximum exhaust flow. Among the options are street and OEM-style replacements, or high-rpm performance and race applications. Choose from styles such as header-back, cat-back, rear axle-back, and full-length. Look over the available options and select the model designed for your vehicle. Depending on the system you order, specs/configurations may include: * One or two mufflers, or a muffler-delete system * Muffler style: wrapped perforated core, turbo, perforated tube, glasspack * Components with a natural or polished finish * Single or dual inlet/outlet * Catalytic converter (where applicable) * Intermediate pipe (where applicable) * Tailpipe; different diameters available * Round tip(s), polished or black coated, various styles Some Kooks Headers exhaust systems are offered in one of three versions: * Off-road (non-catted) for full track use with no horsepower loss and the loudest exhaust tone * With high-flow catalytic converters; recommended for street driving with little or no horsepower loss and a deeper exhaust tone * With Kooks ultra-high performance GREENCATS catalytic converters that eliminate 90 percent of "Check Engine Light" warnings; designed for naturally aspirated and forced induction engines up to 900 hp Note: Certain exhaust systems may not be legal for sale, installation, or use in certain locales. Check your state and local laws.

4.75 out of 5 stars ( 8 )

$1,872.67

$1,349.50

Holley Sniper 2 EFI 650 HP Returnless Fuel Injection Systems

Holley Sniper 2 EFI Returnless Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters before/after the pump, fittings/hardware, and a low profile returnless drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Pre-set, internally regulated pump only requires a single feed line to the Sniper 2 unit * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

5.0 out of 5 stars ( 2 )

$1,899.95

—

$2,149.95

Summit Racing™ Battery Pro Packs

Summit Racing™ battery Pro Packs combo an Optima RedTop battery, Painless battery cable kit, and a tray/hold-down kit for a complete install in your vehicle. The high performance AGM RedTop is Optima's ultimate starting battery designed to deliver a strong burst of ignition power for a reliable start-up every time. The batteries offer longer life, more vibration resistance, no maintenance, and are virtually spill proof and mountable in most any position. Painless Performance battery cable kits include a red 1-gauge positive and a black 1-gauge negative cable with lightweight abrasion-resistant insulation capable of handling over 250 amps and heavy-duty terminals already installed, side post adapters, and high-amp crimp ring terminals. Their 16 ft. length make them ideal for trunk-mounted batteries and custom installs. The battery tray/hold-downs are made from premium aluminum and chosen to match the battery in the Summit Racing™ Pro Pack selected.

Not Yet Reviewed

$550.97

Holley Sniper 2 EFI 650 HP Return-Type Fuel Injection Systems

Holley Sniper 2 EFI Return-Type Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, return line, external regulator, filters before/after the pump, fittings/hardware, and a low profile return-type drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

Not Yet Reviewed

$1,899.95

—

$2,149.95

Holley Sniper 2 EFI 650 HP Returnless Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Returnless Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters before/after the pump, fittings/hardware, and a low profile returnless drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Pre-set, internally regulated pump only requires a single feed line to the Sniper 2 unit * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

4.0 out of 5 stars ( 2 )

$1,999.95

—

$2,249.95

Holley Terminator X Engine Management Systems

Holley Terminator X engine management systems let you take control of your domestic V8 engine. These kits give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X features real-time fuel learn, high impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. All systems come fully loaded with base maps for common engine combinations to get you out of the garage and onto the road or track fast. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors. (Will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables: 4 x 1D tables, 1 x 1D per gear table, 4 x 2D tables, 1 x 2D per gear table * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most domestic V8 engines, as well as tuning and gauge display functions (not available with every kit)

4.48 out of 5 stars ( 96 )

$1,949.95

Holley Sniper 2 EFI 650 HP Return-Type Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Return-Type Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, return line, external regulator, filters before/after the pump, fittings/hardware, and a low profile return-type drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

Not Yet Reviewed

$1,999.95

—

$2,249.95

28 Results Found For "Mopar MDS Delete Kit (Complete)"