Availability
Showing In Stock Items. Show All 4 Items.
DIYAutoTune MegaSquirt Gen 2 plug-and-play engine management systems are standalone units designed as direct-fit, factory ECU replacements offered for a variety of foreign and domestic vehicles. These powerful and cost-effective options typically require an hour or less for installation, and each includes a base map to get the motor fired up easily and ready for fine-tuning to match your engine's needs--from mild to wild. MegaSquirt Gen 2 ECUs get the job done with an impressive feature list that will let you do a lot more than you'd expect anywhere near this price point. DIY AutoTune MSPNP Gen 2 ECUs typically feature: * Fully plug-and-play installation--no wiring required for basic functionality * Base map is pre-loaded to help your engine start on the first turn of the key * Real-time tuning and data-logging with a laptop connection * Supports most aftermarket wideband sensors * 16 x 16 fuel tables allow high-resolution tuning * 12 x 12 ignition tables * Multiple acceleration enrichment strategies * Closed-loop idle speed control * Air conditioner control * Onboard peak and hold drivers support both high and low impedance injectors--no external ballast resistor is needed * Allows removal of stock airflow meter or stock MAF sensor, if so equipped * 12 x 12 air fuel ratio target tables for use with wideband oxygen sensor for precise tuning and table trim * Built-in 2-step rev limiter/launch control with flat shift * Real-time barometric correction * Internal 4-bar MAP sensor reads up to 44 psi of boost * Over-boost protection * Closed-loop boost control (requires boost solenoid kit) * Knock sensor input with adjustable sensitivity * Headphone output for knock sensor--listen for knock while you tune! * Table switching input--change fuel and spark maps on the fly for different fuels, nitrous activation, etc. * Input for flex fuel sensor--switch between E85 and gasoline on the fly! * CAN Bus connector allows interconnection of other MegaSquirt-compatible devices for additional functions, like: EGT input, automatic transmission controller, additional sensors ... the possibilities are limitless! * MegaSquirt Gen 2 plug-and-play ECU * MSPNP RS232 serial tuning cable, 6 ft. (USB adapter sold separately, if needed) * Tuning software and documentation USB stick * 6 ft. vacuum hose for MAP signal and "T" fitting * Four screws for ECU mounting
( 2 )
$869.99
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 21 )
$999.95
MSD Digital E-Curve distributors will drop right into your engine and fire up with three simple connections! Not only are there no external controls or boxes to mount and connect, but you can set a timing curve with the twist of a rotary dial! That's right, no more springs or stop bushings to fumble with. A new digital module lets you select from 20 different "centrifugal" curves and five vacuum curves--that's 100 combinations! Simply remove the cap to access the rotary dials and select a curve to match your application. You can also set an rpm limit that will protect your engine from over-rev damage caused by a missed shift or driveline failure.
( 35 )
$849.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
