Availability
Has it been a while since you serviced your knuckles? Trail-Gear knuckle rebuild kits contain all standard replacement parts, including gaskets, felts, seals, washers, and shims to do the job done right. They even include outer felt covers--a Trail-Gear exclusive! If you're using your truck in the rocks you will want to replace these covers when you service the knuckles. Kits are offered with or without wheel bearings. Service your knuckles with Trail-Gear knuckle rebuild kits.
( 4 )
$127.49
—
$199.99
Trail-Gear Power Flow power steering pump upgrade kits remedy a common flaw in Toyota trucks. The stock pump is just barely able to supply the volume and pressure needed to run hydraulic-assist steering—putting out 1,300 psi at only one gallon per minute. The original pump is not able to provide enough fluid to run both the stock steering and the demands of a ram, especially at low rpm. Drilling out the restrictor plates in a stock pump for more volume often leads to pump failure. The answer is a replacement "TC" style pump. This provides the full fluid volume your steering box and ram are looking for, even at idle. These kits include a 1,650 psi pump, pump bracket, reservoir, reservoir bracket, belt, fittings, hoses, and hardware. The pump kits are designed to work with stock or ram drilled IFS power steering boxes. Additional notes: * The pump and bracket are designed to fit all Toyota 4-cylinder 4WD motors from 1979-95 * A large power steering fluid cooler (included) is required on the low-pressure side of the system * Pump bracket works in conjunction with stock idler bracket * If your truck is not currently equipped with power steering, you will need to purchase the idler bracket and replace the steering gearbox with one designed for use with power steering * The stock fan belt will not work with this pump and will need to be replaced with a Napa 9430 belt. Belt is included with kit. * Note: Never use ATF fluid or a semi-synthetic blend. This will void the warranty. It's okay to use standard power steering fluid or a full synthetic.
( 2 )
$899.99
Trail-Gear pitman arms are designed from solid forged steel construction, and are ideal for use with crossover steering. Replacing your pitman arm is recommended if the original is worn-out or, in most cases, if your steering box is being changed out. These strong, extra-wide one-piece arms will allow the use of FJ80 tie rod ends. They're available in flat style or with the same drop as the factory pitman arm.
( 1 )
$110.49
—
$129.99
With all of the choices on the market for solid axle conversion, you're probably wondering what makes Trail-Gear IFS Eliminator kits stand out? These kits contain the highest quality and most complete parts roster at an affordable price. Plus, Trail-Gear offers the package in three different ride heights! Kits include: * Front leaf springs (your choice of 3, 4, or 5 in. spring) * High Steer crossover steering kit * Front drop hanger with greasable bolts * Greasable 5 in. shackles * Frame tubes and jigs * Steering stabilizer kit * U-bolt flip kit * (2) Shock hoops * (2) Bilstein shocks * (2) Front brake lines * (2) Vented rotors * (2) Bump stop extensions * (2) Wheel spacers * (2) Bump stops * Front axle gusset * Axle diff armor * Knuckle service kit * Wheel bearing kit * Motor mount cover plates * Spring pad * Instructions
( 1 )
$1,799.99
It's all about the springs! Trail-Gear IFS Eliminator heavy-duty kits offer front springs in a more durable version with 20 percent higher spring rate. They have added a 7th leaf and readjusted the length of the leaves to match. So, if you're running a larger V6 or V8 motor, you'll appreciate these muscular springs. Trail-Gear IFS Eliminator heavy-duty kits are available in different configurations to best suit your specific vehicle application needs. Kits include: * Front leaf springs (your choice of 3, 4, or 5 in. spring) * High Steer crossover steering kit * Front drop hanger with greasable bolts * Greasable 5 in. shackles * Frame tubes and jigs * Steering stabilizer kit * U-bolt flip kit * (2) Shock hoops * (2) Bilstein shocks * (2) Front brake lines * (2) Vented rotors * (2) Bump stop extensions * (2) Wheel spacers * (2) Bump stops * Front axle gusset * Axle diff armor * Knuckle service kit * Wheel bearing kit * Motor mount cover plates * Spring pad * Instructions
Not Yet Reviewed
$1,799.99
It's always a plus when we get something that exceeds our normal expectations. Many off-road enthusiasts buy Trail-Gear Creepy Twin transfer case shifters in order to drive in 2WD low—not realizing how much easier the twin sticks make it to shift in and out of 4-low. Access to 2WD low comes in extremely handy in tight switchbacks and other places on the trail where gear reduction is necessary, but 4WD isn't. These shifters are built to impress, with polished cast aluminum bases, black wavy heat-treated 1020 steel shifters, chromoly internal crosspin, and two shift knobs—one for 4.70 and the other for 2WD/4WD. Creepy Twin shifters also feature a splash-resistant oil breather, O-ring seal around each lever, and shifter gasket. To allow independent operation of the shift rails, you'll need to remove the interlock pin from the transfer case. Make 4-wheeling easier with Trail-Gear Creepy Twin transfer case shifters.
( 4 )
$299.99
Truck owners are very impressed by the lineup of Trail-Gear Rock Assault Ram steering assist kits. For example, the Toyota kits feature a selection of various-sized stroke hydraulic rams--with high-temperature inner and outer seals for long life and no leaks. Each ram includes a 3/4 in. rod that's a full 50 percent stronger than other rods on the market. The specially formed 1/4 in. heavy-duty plate steel brackets make installation a snap. Here are the parts included in most Trail-Gear Rock Assault Ram steering assist kits: * Ram with high-temperature inner and outer seals * Rod ends with jam nut * Ram bracket for axle housing * Ram bracket for tie rod * Two hoses * Two JIC 90 degree elbows * Two 1/4 in. NPT x #6 JIC steering box fittings * Mounting hardware * Instructions with photos These kits do require: * Trail-Gear High Steer crossover steering with 1.25 in. tie rod * Tapped steering box
( 3 )
$449.99
Trail-Gear heavy-duty transfer case mounts can handle the abuse of rock crawling and the ultra-low torque of dual cases. Stamped out of 1/4 in. thick steel plate and then welded on a jig to ensure the best fit possible, these mounts are fitted with polyurethane bushings and coated with zinc for lasting performance and durability. Eliminate the worries of a busted T-case mount on the trails with the installation of bomb-proof Trail-Gear heavy-duty transfer case mounts.
( 5 )
$149.99
Trail-Gear wheel spacers are an inexpensive way to gain a little more width out of your axle housing or space your wheels for modifications and/or tire clearance. They're manufactured from 6061-T6 billet aluminum and packaged with studs and matching nuts for a proper fit. There's no need to change out your axle for a wider one when you order the pair(s) of Trail-Gear wheel spacers designed to fit your application.
( 120 )
$135.99
—
$159.99
Trail-Gear Rock Ripper headers offer rip-roaring performance! They are made from thick stainless steel for strength, plus they will not rust, corrode, or need to be wrapped or ceramic coated. They feature 1/16 in. thick tubes going into a 1/2 in. thick header-to-head mounting flange and are TIG-welded and then polished to give them a clean look. Whether you're looking for off-road headers or 49-state legal ones, maybe you have to go 50-state legal--Trail-Gear Rock Ripper headers offer the style and performance you want and need.
( 15 )
$599.99
No weak links. Trail-Gear plus ARP equals strength! These TG hub stud kits offer precision-machined 6mm hex heads to make installation and maintenance easier. You've beefed up your rig with 30 spline birfields, 6-stud knuckles, and chromo hub gears or drive flanges. Finish the job right with Trail-Gear hub stud kits—weakness eliminated! The fasteners are available for a variety of vehicle applications.
( 7 )
$9.99
—
$139.99
Clearance is the key word for off-road enthusiasts. Navigating rocks and rugged terrain leaves your thin steering mechanism vulnerable to damage--which makes Trail-Gear high steer arms invaluable to your vehicle. These pressure-forged steel brackets provide solid mounting points to raise your pitman arm and steering rods a few more inches off the ground. This additional height can mean the difference between safe adventures … or a bent and useless steering component. Trail-Gear steer arms feature tapered tie rod holes for secure contact between parts, and they compensate for angles so your rod ends can ride at the OE-standard 90 degrees. For trucks, 4Runners, Land Cruisers, and other solid front axle rides, TG high steer arms are essential equipment when you venture off the beaten path.
( 3 )
$299.99
—
$349.99
Trail-Gear disc brake kits are strong and easy to install. They started with 3/8 in. CNC laser-cut caliper brackets with Grade 10.9 bolts. The kits utilize larger GM-style calipers that are shipped fully loaded and custom-made, GM-style vented rotors. DOT-approved brake lines are included and designed so that no new fittings are required--one end fits the calipers, and the other end attaches to your OEM brake lines. They also include full-color instructions. Trail-Gear disc brake kits are complete with the strength to keep your stopping power strong.
( 8 )
$594.99
Trail-Gear alternator brackets allow you to upgrade your power and secure it properly to your motor with no major modifications. These TG brackets are designed to bolt a GM-style one-wire alternator to your 20R, 22R or 22RE motor, and will work with your stock alternator belt. Made from heavy-duty steel, the brackets will work with many GM-style alternators. Say goodbye to your small, underpowered OEM Toyota alternator; bolt on the ample power needed with the strength and fit of Trail-Gear brackets.
( 13 )
$99.99
Got a broken OE rubber motor mount? Trail-Gear Bomb Proof engine mount kits offer the quality and strength you need. The base of these motor mounts is made from 1/4 in. plate. The surface plate that the motor sits on is made out of 3/8 in. material and has a Class 10.9 bolt that is mechanically locked to the engine mount plate--not just threaded in. Bomb Proof mounts are given a silver zinc plating that looks sharp and will last a lifetime. The bushings are made out of high-grade polyurethane for added durability, and the mount holes are slotted so that your install is easy. Upgrade your vehicle to Trail-Gear Bomb Proof engine mount kits.
( 9 )
$189.99
If you're installing crossover steering, the time you'll save with one of these mounting kits is well worth the investment. They make swapping to the Trail-Gear IFS steering box much easier. The heavy-duty kits feature 3/16 in. inner and 1/4 in. outer frame reinforcing plates, with angled leading and trailing edges to avoid frame cracking. You'll also receive Grade 8 bolts, crimp nuts, and dependable DOM tubing to complete the project.
( 3 )
$89.99
Trail-Gear Toyota high steer kits feature unbeatable quality at an attractive price. Crossover steering is critical for rock crawling. The stock steering just can't keep pace with today's super-flexible suspension systems. This results in broken stock steering arms and loss of steering. These kits include super-beefy, solid forged steering arms, a heavy-duty pitman arm, heavy-duty 0.250 in. wall steering rods, and rod ends. The kits are precision-fit for easy assembly.
( 3 )
$549.99
—
$749.99
Get rock-crawling control with the addition of Trail-Gear reduction gears. Lower case gears can provide the enhanced trail performance you want, and these reduction gears are precision-ground and micro-polished to do just that—at an affordable price. Gears, gaskets, seals, and possibly more (depending on the gear set chosen) are available, as well as a choice of spline configurations. Keep your rig in high performance with Trail-Gear low-range climbing reduction gears.
( 7 )
$599.99
Trail-Gear universal shock hoop kits are long enough to accommodate extended-length shocks. They're made from 1035 DOM and precision CNC-bent to ensure the highest quality product. The shock hoops are available in different sizes for fitment on specific applications. A universal model measures 16 in. from top to bottom, and 13 in. from the weldment mounting surface to the shock eye bracket.
( 6 )
$99.99
Trail-Gear Trail Safe wiper seals keep your knuckle balls cleaner, ride after ride. How? With engineering innovation! Each of these knuckle ball wiper seals feature a double-sided design—with a grease seal lip and a wiper seal lip that efficiently keep the dirt out and the grease in. They're constructed in one-piece of high-grade polyurethane, not UHMW, which means they're more durable and pliable for easier installation and a lifetime of dependability. Tired of wiping the clumps of dirty, sandy grease off your knuckle balls? Toss the factory felt and rubber … and replace them with innovative Trail-Gear Trail Safe wiper seals. Your kit includes: * Trail Safe knuckle ball seal wipers * Rock ring kit * Rock ring bolts * M6 lock washers
( 1 )
$119.99
Need a replacement alternator for your Toyota Pickup or 1st Gen 4Runner? Need both the alternator and the perfect bracket kit? You've come to the right place. Trail-Gear's GM 3-wire alternator is a remanufactured 78 amp 3-wire Delco 12si alternator with a pigtail harness—great for Toyota alternator swaps. The optional GM alternator bracket allows you to bolt your GM style 3-wire alternator to your 20R, 22R, or 22RE motor with no major modifications—and it works with your stock alternator belt. Say goodbye to your small, underpowered OEM Toyota alternator and upgrade to a GM-style unit to supply ample power for rock lights, stereo, GPS and all the other gadgets you're running. AVAILABLE OPTIONS: * TGI-308845 - GM 3-Wire Alternator - with GM Alternator Bracket Kit * TGI-309407 - GM 3-Wire Alternator - without GM Alternator Bracket Kit
( 2 )
$269.99
If you need to relocate your rear shackle mounts in order to install longer suspension springs, it's the perfect time to upgrade to Trail-Gear leaf spring shackles. These 1/4 in. steel plate units are stronger than the original factory shackles, offering more security when scaling rough terrain. Trail-Gear leaf spring shackles will use your OEM bushings or stock replacements. Order the pair designed for your vehicle application.
( 5 )
$129.99
Trail-Gear speedometer adapters remedy issues with adapting your electrical speedometer to the transfer case. These cable adapters convert a Toyota mechanical speedometer sensor to an electrical speedometer sensor—by just screwing it onto your mechanical speedometer sensor and plugging it into the sensor wiring harness on your vehicle. Trail-Gear speedometer adapters accept standard Toyota 3-pin speedometer sensor plugs. Order the model designed for your vehicle application.
( 1 )
$49.99
Trail-Gear differential armor is the perfect addition in order to help you protect your differential gears from unnecessary damage. They are precision laser-cut from 1/4 in. A36 steel, and then CNC-formed to provide a perfect fit and finish for the best protection available. Help yourself save valuable time and money when riding with Trail-Gear differential armor. It's one of the best investments you can make.
( 6 )
$79.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
