Availability
Shop limited-time discounts on parts, tools, and accessories from your favorite brands!
Shop limited-time discounts on parts, tools, and accessories from your favorite brands!
Shop limited-time discounts on parts, tools, and accessories from your favorite brands!
Showing In Stock Items. Show All 954 Items.
On Sale
Stock intake manifolds in electronic fuel injection vehicles often fall short of lasting for the life of the vehicle. Being molded from polymers they tend to warp or crack and start leaking vacuum or coolant over the years. Summit Racing™ Premium EFI intakes are just what you need when it's time to replace your manifold as our design improvements address the failures that occur with existing manifolds for this application on the market today. These units are made to fit your specific vehicle and come complete with the necessary hardware for an easy OE type installation. Make this the last manifold you ever buy for your car or truck. Check out these features and benefits below: • Made in USA by OE Tier 1 Supplier • Aluminum crossover design improvement to mount direct to the cylinder head eliminating coolant exposure and eventual failure at the plastic interface of existing manifolds on the market. • High grade coolant resistant material used in coolant fitting and block out locations to coolant system. All coolant exposure areas are addressed with appropriate material. • Heat staked inserts for coil mounting. • Includes alternator brackets, throttle body adapter (application specific), thermostat, gaskets or O-ring seals, and mounting hardware.
( 56 )
$204.99
—
$379.99
$199.99
—
$339.99
On Sale
Holley EFI LS Hi-Ram intake manifolds are designed for your high performance race engine. Big cube and high-rev applications without height limitations are the intent for these manifolds. The modular design of these Holley Hi-Ram intake manifolds offers a runner length and as-cast tapered cross-section design that works for a wide range of engine configurations. The included fuel rails are machined for -8 AN O-ring fittings with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. Build maximum performance with EFI LS Hi-Ram intake manifolds from Holley.
( 39 )
$1,149.95
—
$1,299.95
$1,033.95
—
$1,168.95
On Sale
When you're serious about power for your LS or new LT1 engine, call in the AirForce! MSD Atomic AirForce intake manifolds have been designed using Computational Fluid Dynamic Modeling to create optimal plenum volume and efficient paths for improved airflow and distribution to stock and modified engines. Their unique bell-mouthed runner entrances maximize airflow and minimize shrouding--efficiently using the available plenum volume for an unobstructed flow path over opposing runners. The 2-piece molded polymer design resists heat soak, minimizes weight, and allows easy access to the runners for porting. MSD Atomic AirForce intake manifolds accept an OEM or 103mm throttle body, as well as stock, aftermarket, or Atomic LS EFI fuel rails. They are supplied with new gaskets and hardware for a direct bolt-on package. The 103mm throttle bore allows the use of large throttle bodies for greater airflow, and a direct-flow path runner design promotes maximum airflow.
( 19 )
$1,349.95
—
$1,649.95
$1,213.95
—
$1,483.95
On Sale
Weiand Street Warrior intake manifolds are designed for use on stock or stroker combinations and more efficient cylinder heads. With new cam designs came the need for Street Warrior intake manifolds to support these combinations. Designed with Computational Fluid Dynamics software, Street Warrior intake manifolds rise to the challenge and deliver the performance to conquer the competition. Do you want maximum horsepower and torque from today's engines? Then choose Street Warrior intake manifolds.
( 140 )
$279.95
—
$499.95
$251.95
—
$448.95
On Sale
Weiand dual plane Stealth intake manifolds feature long, separated runners for bottom-end and mid-range power, plus a special runner design and larger plenum to flow the air needed for high-rpm horsepower. They mount single, square-mount 4-barrels and make power from idle all the way to 6,000 rpm. That makes Stealth manifolds the perfect choice for your street/strip vehicle. Order the size and style needed for your cylinder head application.
( 154 )
$323.95
—
$449.95
$291.55
—
$403.95
On Sale
Weiand Action Plus intake manifolds are designed for use as stock replacements, with improved power and torque characteristics. They're 180 degree, dual plane types, with a carburetor flange that'll accept either stock or aftermarket performance carburetors. Their effective rpm range runs from idle to 6,000 rpm. With their high-flow runner design and ability to produce increased power with little modification, it's no wonder these manifolds are so popular.
( 65 )
$377.95
—
$412.95
$268.95
—
$340.15
On Sale
Holley LS Modular Lo-Ram EFI intake systems have a top-feed plenum entry configuration, designed to allow the currently available Hi-Ram 105mm plenum tops to be fitted to a low-profile base intake manifold. The short runner, low-profile base intake manifold intended for forced induction applications and was conceived to package with an air-to-water plenum-mounted intercooler—with a shorter overall height than is possible with other existing intake manifolds. Using a modular design, the top-feed plenum configuration with 105mm top keeps the overall height at just 9.07 in.! Additional features and specs include: * Cast aluminum construction * Modular design allows the use of the included top-feed plenum entry * Designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads * Will also work with OE or aftermarket cylinder heads * Designed for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000 to 8,000 rpm, depending on application * Low height to aid the packaging of a plenum-mounted air-to-water intercooler in a top-feed configuration (or to fit under a stock or mildly modified hood in the front-feed configuration) * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits come with two sets of brackets—a set for long (usually standard length) fuel injectors, and a set for short (such as Pico or LS7) fuel injectors
( 1 )
$1,099.95
$988.95
On Sale
The Trinity Series intake manifolds is BTR's latest offering in high-quality cast aluminum intake manifolds for LS7 engines. Their short runner, 3-piece design allows for the ultimate in application flexibility and is similar in concept to billet intakes costing thousands more. Optimum operating range is 6000-8500 rpm and is primarily intended to bridge the gap between N/A and Boosted applications. These intake manifolds utilize the high LT1 throttle body position and accepts DBW or cabled throttle bodies, yet will fit in the tight confines of the C7, C6, C5 Corvette, as well as the popular F-body platforms. BTR Trinity Series intake manifolds come semi-assembled and includes all hardware required to bolt it on. Additional features: * Available in choice of silver or black satin texture powdercoat finishes * Design incorporates two runners and an interchangeable plenum * Both the port mouth radius and the port match are CNC-machined * Seal is generated by eight entrapped O-rings at the runner/plenum interface and is clamped by M6 stainless steel socket head cap screws * Port seals are achieved SAE O-rings seated in a dovetailed O-ring groove * Incorporates two ports on the side of the throttle body boss and on the rear * Runners and plenums can be purchased separately
( 1 )
$824.99
—
$999.99
$742.49
—
$899.99
On Sale
Corsa carbon fiber DryTech 3-D air intakes blend aesthetics and engineering to deliver in a single package. The intakes efficiently direct airflow from the filter to the throttle body. Streamlining the airflow eliminates any calibration concerns, and helps increase throttle response. Features include: * 100 percent carbon fiber construction * Outflows stock intake creating more horsepower and torque * DryTech 3-D synthetic dry filter
( 6 )
$675.99
—
$758.99
$608.39
—
$683.09
On Sale
The next generation of air intakes is here! aFe Momentum GT Pro 5R air intake systems use the most up-to-date engineering tools and techniques to provide you with the perfect blend of power and protection. Their one-piece sealed housing with an auxiliary air scoop is designed to eliminate the use of multiple housings and ensure the coolest air intake charge available. A urethane plug is also included for those cold-weather applications where you want to block off the auxiliary air scoop. These systems feature premium stainless steel T-bolt clamps and a 2-ply, reinforced silicone coupler at the throttle body for increased strength and durability. They also include a 5-layer washable and reusable Pro 5R air filter. Experience maximum horsepower gains, huge low-end towing power, increased torque, and a throaty, mean growl for your performance machine with the Momentum GT Pro 5R air intake systems from aFe.
( 100 )
$350.00
—
$959.00
$315.00
—
$863.10
On Sale
Holley EFI LS Mid-Rise intake manifolds are designed for your high performance race engine. They're an excellent choice for street and performance street/strip applications. They're intended for big cube and high-rev applications without height limitations. The modular design of these manifolds offers a runner length and as-cast tapered cross-section design that works for a wide range of engine configurations. The included fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. Build maximum performance with EFI LS Mid-Rise intake manifold bases from Holley.
( 7 )
$1,099.95
—
$1,149.95
$988.95
—
$1,033.95
On Sale
BTR Equalizer 1 intake manifolds are low-profile, high performance intakes. Cast from 319 aluminum, these Brian Tooley Racing manifolds are designed for combinations that are looking to make peak power between 6,000 and 8,000 rpm. Boosted engine combinations are actually more reliable making peak power in this higher rpm range, compared to making peak power around 6,500 rpm like most stock style intakes, provided the valve train is engineered properly. These units are available for a variety of applications from 1997 and up. Features and specifications for Equalizer 1 manifolds: * O-ringed port openings and lid surface * Easy insert steep chamfer injector bores for trouble-free injector O-ring insertion * Underslung plenum design for maximum hood clearance * 102mm profiled throttle bore * One map sensor location in rear, with two additional user optional locations * Additional user-defined LS3 and LS1, LS2, and LS6 map sensor bores * ISO9001:2015 certified machining * 2-piece design for easy porting access * Lightweight CAD-generated design * Profiled port openings for optimum out-of-the-box performance * All threads are roll form aircraft standard DSDV * Clears F-body cowls * Clears C5 cowls with minimal massaging to intake
( 5 )
$749.99
—
$799.99
$674.99
—
$719.99
On Sale
Holley offers EFI Hi-Ram intake manifolds for a variety of applications, including many vehicles from the 1950s, '60s, '70s, and '80s with a Chevy small block Gen I engine. Fuel rail kits are provided and have mounting for both long and short type fuel injectors. These manifolds offer the performance potential and the appearance of professionally prepared billet and fabricated racing intake manifolds at the affordable price of a cast-aluminum product. They deliver 21st century performance for the iconic small-block Chevy engine. * Model 300-950 is of standard Hi-Ram configuration with a "top-feed" plenum and a plenum top designed to accept up to an 105mm Gen IV LS 4-bolt throttle body, including drive-by-wire throttle bodies. * Model 300-951 is a hood-height friendly Hi-Ram variation which has a "front-feed" plenum and a forward-facing throttle body flange which accepts an up to 95mm LS 4-bolt throttle body, also, including DBW throttle bodies. It's an upgrade replacement for the Holley/Weiand Stealth-Ram intake manifold which was a popular manifold used to significantly improve the performance of 1985-92 GM 5.7L TPI fuel-injected engines. The 300-951 system installs under the OE hood for Gen 1, 2, and 3 Camaros and Firebirds. It should be compatible with most applications with a mild cowl induction hood. * Uses drive-by-wire or cable-actuated GM Gen IV LS 4-bolt throttle bodies * Throttle cable bracket is supplied in the kit * GM Gen IV LS MAP sensor port. Also has provisions for (1) 1/8 NPT, (1) 1/4 NPT, (1) 3/8 NPT fittings to the plenum * Power band: 1,500-8,000 rpm * Black anodized EFI fuel rails are machined for -6 AN O-ring fittings and come included with these EFI Hi-Ram kits * Plenum top gasket type – 3/32 in. round O-ring cord * Cast 356-T6 aluminum construction, natural, satin as-cast aluminum finish * Requires the use of early type GM or small cap MSD or Holley distributors. Not compatible with HEI distributors * 1.95 in. tall x 1.25 in. wide port flange openings
( 2 )
$999.95
$898.95
On Sale
Momentum Pro 5R air intake systems from aFe are designed around a large pre-oiled 7.5 in. tall, oval, cotton media filter with five layers of progressively finer mesh to maximize performance. These incredible filters fit into equally impressive one-piece housings with auxiliary air scoops and large clear sight windows. When combined with the housings, these aFe air intake systems outflow the factory unit by 31 percent—yielding average gains of 11 hp and 13 lbs.-ft. of torque. They also include a urethane plug to block the scoop if not used. Give your engine more go power with aFe Momentum Pro 5R air intake systems.
( 12 )
$361.00
—
$729.00
$324.90
—
$656.10
On Sale
Spectre Performance cold air intake kits provide better acceleration and fuel economy for your truck or SUV. They're designed to replace your factory air filter and air box assembly, eliminating the restriction as they smooth and straighten airflow. The high-flow design of these intakes enables your engine to breathe in a larger volume of air, resulting in more usable power throughout the engine's entire rpm range. Hundreds of models are available, with various tube and filter options. Choose the kit tailored for fitment and performance on your make/model application.
( 833 )
$198.99
—
$199.99
$174.99
On Sale
Holley LS Modular Lo-Ram EFI intake manifolds are designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications and a 105 mm throttle or similar models. The base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood in the front-feed configuration. The modular design allows the use of front-feed plenum entry, while intake design facilitates custom inlet duct and throttle body placement. Additional features and specs: * Cast aluminum construction with satin silver finish * Modular design allows the use of front-feed plenum entry * Clears 4th Gen Camaro and C5 Corvette cowls and hoods without modification * With forced-induction and the short runner length the engine rpm at which peak power occurs is more likely to be coupled to the supercharger or turbocharger being used * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits include two sets of brackets; a set for long (usually standard length) fuel injectors and a set for short (such as Pico, or LS7) fuel injectors
( 8 )
$649.95
—
$1,249.95
$583.95
—
$1,123.95
On Sale
Holley Sniper EFI fabricated intake manifolds are budget-friendly and performance laden! These durable Holley hi-ram manifolds feature 3mm (1/8 in.) thick T-6061 sheet aluminum construction with 100 percent TIG welds. The EFI versions have 92mm or 102mm throttle body openings, as well as runners with tapered tops to increase velocity and evenly distribute airflow. They also include 3/8 in. fuel rail kits and, of course, are branded with the Holley Sniper EFI logo. Budget and performance go hand-in-hand when it comes from Holley in the form of their Sniper EFI fabricated intakes. Order the model and options recommended for your make/engine application.
( 17 )
$786.95
—
$949.95
$467.95
—
$853.95
On Sale
Holley EFI LS Hi-Ram intake manifold bases are cost-effective alternatives to fabricated sheet metal for high performance applications where induction system height is not limited. Coupling these cast aluminum Hi-Rams with the high flowing LS-style cylinder heads has outstanding potential for N/A and forced induction applications at a budget-minded cost. These modular lower manifolds accept a wide range of carbureted and EFI tops, making them attractive to builders and fabricators as the perfect foundations for custom induction systems. Fuel rails are included and machined for -8 AN O-ring fittings with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. The aggressive, bold, race-bred styling of Holley GM LS modular Hi-Ram lower manifolds will make bad intentions clear for drag race, muscle car, marine, off-road, sand rails, pulling trucks, track, and street-rod applications.
( 1 )
$899.95
—
$999.95
$808.95
—
$898.95
On Sale
Revolutionize the way your engine performs with power-boosting Weiand Track Warrior intake manifolds! Designed for high performance engine applications, they are ideal for mean street machines as well as for competition super-class big block powerplants. They are computer engineered and dyno-proven to produce more horsepower and torque as a result of superior cylinder-to-cylinder distribution, giving the Track Warriors the edge over the competition and ensures safe, consistent air/fuel ratios for your engine. Plus, permanent mold castings provide weight savings of 10 to 20 percent over traditional sand cast pieces while maintaining inform wall thickness for porting. So, when you look for the pinnacle of performance, price and quality, just look to Weiand.
( 26 )
$463.95
—
$549.95
$302.95
—
$493.95
On Sale
K&N 63 Series Aircharger high performance cold air intake kits are designed to eliminate air path restriction and deliver a massive amount of air into your engine, resulting in more power. These kits are guaranteed to increase horsepower. They are engineered for specific vehicles to replace the OEM setup, including those with computer systems. The air filter element is washable and reusable, lasting up to 100,000 miles before service is required (driving conditions dependent). Where applicable, protective heat shields and hardware are included with installation designed to use factory holes and mounting points for easy installation. The air must flow—and it will when you order the K&N 63 Series Aircharger cold air intake kit best suited for your application!
( 602 )
$345.99
—
$682.99
$317.99
—
$632.99
On Sale
Holley EFI LT1 Gen V Hi-Ram intake manifolds provide the ultimate performance with GM direct-injected Gen V 6.2L LT1 engines. The modular design allows easy disassembly for custom porting, multiple tops, or custom induction systems. Each runner has a large radius where it meets the plenum, and optimized taper and cross-sectional area to perform in a wide variety of engine configurations. When you look for the pinnacle of performance, price, and quality, look to Holley Hi-Ram intake manifolds for your LT1 application. Features include: * Available with injector bosses on the intake runners that provide increased performance potential by using additional injectors and the factory direct injection * Removable top * Large plenum volume * Intakes with injector ports include fuel rails with dual mounting * Fuel rails are anodized, laser-etched, and machined for -8 AN O-ring fittings at each end * Rear of plenum machined for MAP sensor and three vacuum ports * Head flange has clearance for fuel supply to a high-pressure pump * Increased runner wall thickness for custom porting at the plenum to runner entry on each runner * O-ring seals at cylinder heads and plenum top * Easy assembly with top-mounted screws on plenum top (except front two screws) * Several top options: 1 x 95mm, 1 x 105mm, 2 x 4150, 2 x 4500, or blank flange for custom throttle bodies * 3,500 to 8,000-plus rpm power band
( 2 )
$949.95
—
$1,299.95
$853.95
—
$1,168.95
On Sale
Flowmaster Delta Force cold air intakes are the elite kits you can call upon to help attain maximum performance and efficiency for your vehicle. All systems feature ultra-trick looking durable cross-linked polyethylene intake tubes with a large high-flow conical shaped air filter ensuring it will trap more dirt/dust particles than the typical filter. They are highlighted with Flowmaster logos to show others you're serious about quality and performance. Installation is easy utilizing factory mounting points. Take "operation cool airflow" to the next level with the addition of Delta Force cold air intake kits. Flowmaster Delta Force cold air intakes feature: * Roto-molded cross-linked polyethylene (XLPE) high-flow intake tube * Custom-designed black powdercoated air dam with foam rubber seal * Reusable/cleanable air filter * Multi-layer reinforced silicone couplers * Anodized aluminum fittings * Stainless steel hardware * No tuning required
( 8 )
$362.95
—
$549.95
$274.95
—
$470.95
On Sale
Holley EFI intake manifolds feature port-matched upper and lower runners for reduced restrictions. Plus, the EGR passages have been relocated to the outside of the manifold to allow for the use of larger intake ports. The result is greater air capacity, which makes these manifolds the perfect choice for supercharged engines. They're available in a variety of styles and options; select the model designed for your vehicle and/or engine application.
( 6 )
$599.95
—
$682.95
$538.95
—
$613.95
On Sale
Maximize your engine's performance with Airaid SynthaMax CAD cold air intake kits. The cold air dam design seals directly to the hood and isolates engine heat away from your intake, allowing cooler air to run through the system. These cold air intake kits feature dual-layered SynthaMax filters, constructed using the finest 100 percent synthetic materials for unrivaled filtering efficiency. Servicing the filters is easy with oil-free maintenance—simply wash them in a mild household detergent and rinse. Airaid SynthaMax cold air intake kits are built with a hand-poured urethane body that won't crack, curl, or shrink. They use the stock air filter location, but add a boost with a huge air inlet that keeps more cold air flowing through the 360 degree filter. Hundreds of models are available for a wide range of vehicle applications. Maximize your horsepower, torque, and fuel efficiency with Airaid SynthaMax CAD cold air intake kits.
( 28 )
$367.99
—
$472.99
$317.99
—
$422.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
