Availability
Showing In Stock Items. Show All 8 Items.
On Sale
PerTronix Flame-Thrower Ceramic Hi-Temp universal spark plug boots protect against direct heat, withstanding up to 2,000 degrees F. These universal boots provide the very best protection for applications with tight fitting headers or exhaust manifolds, and they fit typical 8mm spark plug wires. Pertronix offers the Flame-Thrower Ceramic Hi-Temp boots in several boot angle configurations individually and in sets of 8 to retrofit an entire spark plug wire set. Each kit includes pure silicone plug(s), wire bushing(s), spark plug terminal(s), and high-temperature ceramic boot(s).
( 36 )
$123.60
$111.24
On Sale
Holley EFI Gen III Hemi VVT and SRV harnesses offer control. 2009+ Gen III Hemi engines rolled off the showroom floor with Variable Valve Timing (VVT). Now, both Holley Terminator X and Terminator X Max ECUs will allow you to control and tune the VVT with the use of the plug-and-play VVT harness. But the fun does not stop there! If you are using a stock intake manifold that came from the factory with the Short Runner Valve (SRV), Holley also has a plug-and-play sub harness that will allow you to utilize the SRV actuator and capitalize on its low rpm torque benefits. Features: * Plug-and-play with the factory Gen III HEMI VVT sub-harness, and any Holley EFI HEMI main harness connecting to the power tap and input/output connectors * Provides control of VVT solenoid under the intake manifold * SRV (Short runner valve) connector pre-wired into the sub harness allowing you to simply plug into the factory SRV actuator in the intake manifold
Not Yet Reviewed
$163.95
$147.55
On Sale
The pressure inside your intake manifold is extremely important input to the ECU—so a quality MAP sensor from MSD is crucial to your engine's performance. These replacement sensors will respond to changes in manifold pressures and relay the information to the ECU in the form of a voltage signal ranging from about 1 to 5 V. They're available in several different versions for naturally aspirated engines, as well as engines with forced induction.
( 11 )
$184.95
$166.45
On Sale
These V-Force Plus power control modules are designed for the performance enthusiast who wants improved performance, acceleration, and the ability to monitor vehicle information. V-Force Plus power control modules are designed around a 20 MHz RISC processor. V-Force Plus power control modules optimize ignition advance and fuel maps for optimum horsepower and drivability. In addition, the software in the program allows you to select from 14 different screens to monitor throttle position, mass airflow, manifold pressure, fuel economy, and air/fuel ratio. This allows you to monitor your driving habits for the best fuel economy and performance.
( 12 )
$299.96
$269.96
On Sale
MSD 8.5mm Super Conductor spark plug wire sets feature a special helically wound core that has just 40-50 ohms of resistance per foot—but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire includes 40 ft. of tightly wound copper for superior conductivity. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference "choke." This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Each set comes with clip-on cylinder markers for easy identification. MSD's 8.5mm Super Conductor wire sets are available in custom or universal-fit applications, assembled or not, with a variety of terminal and boot end options.
( 1972 )
$118.95
—
$167.95
$107.05
—
$151.15
On Sale
MSD 8.5 mm Race Tailored Super Conductor Wire Sets are designed to specifically fit race engines equipped with headers or MSD distributors. They feature wires that are custom cut to route behind the block, under the headers, and to the spark plugs. This routing gives the engine an extra clean appearance as well as protecting the wires from making contact with the engine. The wires have a special helically-wound core that has just 40-50 ohms of resistance per foot--but with the RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire features 40 feet of tightly wound copper for superior conductivity. A tough 8.5 mm synthetic/silicone jacket over an extra heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, stainless steel terminals feature snap locks to assure a secure fit.
( 13 )
$210.95
$116.95
On Sale
ThunderVolt 8.2mm wires from Taylor are an easy, proven, dyno-tested way to gain more power—simply by changing your spark plug wires! These factory replacement, ultra-high performance ignition wire sets are loaded with features and benefits, including: * 50 ohms of resistance per foot * 100 percent silicone 2-layer jacket * Ferrite spiral-wound coated core * RFI and EMI-compatible for all ignition systems * Dyno-tested to outperform the competition * Superior spark energy * Increased horsepower * Significant torque gains * Smoother idle * Improved fuel economy * Universal, race, and custom fit sets available
( 649 )
$226.50
$203.85
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
