Availability
On Sale
Holley LS Modular Lo-Ram EFI intake manifolds are designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications and a 105 mm throttle or similar models. The base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood in the front-feed configuration. The modular design allows the use of front-feed plenum entry, while intake design facilitates custom inlet duct and throttle body placement. Additional features and specs: * Cast aluminum construction with satin silver finish * Modular design allows the use of front-feed plenum entry * Clears 4th Gen Camaro and C5 Corvette cowls and hoods without modification * With forced-induction and the short runner length the engine rpm at which peak power occurs is more likely to be coupled to the supercharger or turbocharger being used * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits include two sets of brackets; a set for long (usually standard length) fuel injectors and a set for short (such as Pico, or LS7) fuel injectors
( 8 )
$649.95
—
$1,249.95
$583.95
—
$1,123.95
On Sale
When you're serious about power for your LS or new LT1 engine, call in the AirForce! MSD Atomic AirForce intake manifolds have been designed using Computational Fluid Dynamic Modeling to create optimal plenum volume and efficient paths for improved airflow and distribution to stock and modified engines. Their unique bell-mouthed runner entrances maximize airflow and minimize shrouding--efficiently using the available plenum volume for an unobstructed flow path over opposing runners. The 2-piece molded polymer design resists heat soak, minimizes weight, and allows easy access to the runners for porting. MSD Atomic AirForce intake manifolds accept an OEM or 103mm throttle body, as well as stock, aftermarket, or Atomic LS EFI fuel rails. They are supplied with new gaskets and hardware for a direct bolt-on package. The 103mm throttle bore allows the use of large throttle bodies for greater airflow, and a direct-flow path runner design promotes maximum airflow.
( 19 )
$1,349.95
—
$1,649.95
$1,213.95
—
$1,483.95
On Sale
Holley EFI LS Hi-Ram intake manifolds are designed for your high performance race engine. Big cube and high-rev applications without height limitations are the intent for these manifolds. The modular design of these Holley Hi-Ram intake manifolds offers a runner length and as-cast tapered cross-section design that works for a wide range of engine configurations. The included fuel rails are machined for -8 AN O-ring fittings with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. Build maximum performance with EFI LS Hi-Ram intake manifolds from Holley.
( 39 )
$1,149.95
—
$1,299.95
$1,033.95
—
$1,168.95
On Sale
Weiand Action Plus intake manifolds are designed for use as stock replacements, with improved power and torque characteristics. They're 180 degree, dual plane types, with a carburetor flange that'll accept either stock or aftermarket performance carburetors. Their effective rpm range runs from idle to 6,000 rpm. With their high-flow runner design and ability to produce increased power with little modification, it's no wonder these manifolds are so popular.
( 65 )
$377.95
—
$412.95
$268.95
—
$340.15
On Sale
Weiand dual plane Stealth intake manifolds feature long, separated runners for bottom-end and mid-range power, plus a special runner design and larger plenum to flow the air needed for high-rpm horsepower. They mount single, square-mount 4-barrels and make power from idle all the way to 6,000 rpm. That makes Stealth manifolds the perfect choice for your street/strip vehicle. Order the size and style needed for your cylinder head application.
( 154 )
$323.95
—
$449.95
$291.55
—
$403.95
On Sale
Holley LS Modular Lo-Ram EFI intake systems have a top-feed plenum entry configuration, designed to allow the currently available Hi-Ram 105mm plenum tops to be fitted to a low-profile base intake manifold. The short runner, low-profile base intake manifold intended for forced induction applications and was conceived to package with an air-to-water plenum-mounted intercooler—with a shorter overall height than is possible with other existing intake manifolds. Using a modular design, the top-feed plenum configuration with 105mm top keeps the overall height at just 9.07 in.! Additional features and specs include: * Cast aluminum construction * Modular design allows the use of the included top-feed plenum entry * Designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads * Will also work with OE or aftermarket cylinder heads * Designed for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000 to 8,000 rpm, depending on application * Low height to aid the packaging of a plenum-mounted air-to-water intercooler in a top-feed configuration (or to fit under a stock or mildly modified hood in the front-feed configuration) * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits come with two sets of brackets—a set for long (usually standard length) fuel injectors, and a set for short (such as Pico or LS7) fuel injectors
( 1 )
$1,049.95
—
$1,149.95
$747.95
—
$988.95
On Sale
These CrossWind intake manifolds from Professional Products feature identical plenum and runner designs to the Typhoon. The main difference is that there is an open area under the plenum chamber. This feature is sometimes called an air gap design. The air flowing under the plenum provides a cooler charge for the incoming air with less heat transfer from the engine. This cooler air charge provides additional power.
( 43 )
$171.99
—
$339.99
$154.79
—
$305.99
On Sale
Holley EFI LS Mid-Rise intake manifolds are designed for your high performance race engine. They're an excellent choice for street and performance street/strip applications. They're intended for big cube and high-rev applications without height limitations. The modular design of these manifolds offers a runner length and as-cast tapered cross-section design that works for a wide range of engine configurations. The included fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. Build maximum performance with EFI LS Mid-Rise intake manifold bases from Holley.
( 7 )
$1,099.95
—
$1,149.95
$988.95
—
$1,033.95
On Sale
Holley EFI LS single plane mid-rise intake manifolds are great for your higher horsepower engine. Featuring cast aluminum construction, these manifolds are also great for centrifugal blower, turbocharged, or NOS mild power adder applications. The efficient casting design is lightweight--11.5 lbs.--with consistent wall thickness and strong mounting flanges. The optimized runner layout and constant cross sectional area offer a broad torque curve, with the best vehicle performance from 2,500 to 7,000 rpm. The mid-rise design offers minimum carb mounting flange height--without sacrificing power--and is another plus for vehicles with minimum hood modifications. Holley EFI LS single plane mid-rise intake manifolds include zinc-plated hex head cap mounting bolts and washers, pipe plugs to block manifold vacuum and MAP sensor ports, and Viton® O-ring cylinder head mounting flange gaskets for an OEM-style seal.
( 9 )
$479.95
—
$549.95
$274.95
—
$493.95
On Sale
Holley Sniper EFI fabricated intake manifolds are budget-friendly and performance laden! These durable Holley hi-ram manifolds feature 3mm (1/8 in.) thick T-6061 sheet aluminum construction with 100 percent TIG welds. The EFI versions have 92mm or 102mm throttle body openings, as well as runners with tapered tops to increase velocity and evenly distribute airflow. They also include 3/8 in. fuel rail kits and, of course, are branded with the Holley Sniper EFI logo. Budget and performance go hand-in-hand when it comes from Holley in the form of their Sniper EFI fabricated intakes. Order the model and options recommended for your make/engine application.
( 17 )
$786.95
—
$949.95
$467.95
—
$853.95
On Sale
Holley EFI intake manifolds feature port-matched upper and lower runners for reduced restrictions. Plus, the EGR passages have been relocated to the outside of the manifold to allow for the use of larger intake ports. The result is greater air capacity, which makes these manifolds the perfect choice for supercharged engines. They're available in a variety of styles and options; select the model designed for your vehicle and/or engine application.
( 6 )
$599.95
—
$682.95
$538.95
—
$613.95
On Sale
Performance Design XS intake manifolds break the mold of existing intake manifold architecture to maximize available space under the hood. When designing the optimum intake runner length and shape, the fuel rail gets in the way—so they moved it—inside the intake manifold! Those billet fuel rails feature an external quick-disconnect near the stock location. Testing proved these models, featuring injection-molded, glass-reinforced nylon construction, made horsepower and torque gains on a stock engine—with increasing gains as the engine got more aggressive with camshaft and exhaust upgrades! Other product features and specifications include: * Modular runners with three staggered lengths for best performance * Forward-facing throttle body flanges (90-101mm, 103mm, and 112mm) * Full assembly can be reversed on the engine * Fits under the cowl hood of a C6 Chevy Corvette * Factory MAP sensor location * PCV and canister purge solenoid OEM connections * Accepts standard EV6 LS3/LS7-style injectors * Injector extension wires pass through sealed grommets * Maximum recommended boost is 20 psi * Carbon fiber center bolt cover * Includes stainless steel hardware for installation * Includes molded port, plenum, and throttle seals
Not Yet Reviewed
$999.99
$899.99
On Sale
Holley introduces a new addition to their manifold line up—the SBF Hi-Ram EFI intake manifolds that come with an LS throttle body flange top (in either 95mm or 105mm throttle body sizes). Their runner length and tapered cross-section design will perform well for a wide range of engine configurations. The Holley engineering team also redesigned the water crossover passage to allow room for distributor phasing. With the aggressive, bold, race-bred styling, there's no doubt that these Hi-Ram EFI manifolds will make your bad intentions clear for drag racing, muscle car, marine, off-road, sandrails, pulling trucks, competition track, street rod applications, and more! Additional features and specs include: * Cast aluminum construction * Available in natural cast aluminum or black powdercoat finish * Manifold is designed for an 8.2 in. SBF deck height * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system; they come standard with EFI Hi-Ram kits * Plenum top gasket type: 3/32 in. round O-ring cord * A low-profile distributor will be needed when using this manifold (sold separately)
( 5 )
$1,249.95
$812.95
—
$1,123.95
On Sale
Holley's low-profile intake manifold for Ford's 7.3L Godzilla engine, when paired with a 20-340/20-340BK oil pan and accessory drive kit, allows for easy installation into vintage vehicles, kit cars, and other space-restricted applications while retaining the factory hood. The design focus for these manifolds was equal cylinder distribution and great street manners. The low-profile intake manifolds offer a much cleaner alternative to the original plastic intake; they provide anywhere from 2 to 3.5 in. of additional clearance, will correct the OE throttle body angle by 55 degrees, and increase the opening to 92mm. With three throttle body options, sturdy cast aluminum construction, a removable lower panel, and long runners to maintain the 7.3L's already substantial torque offering, this is a must-have for any Godzilla project. Throttle Body Options: * 1) 1986-1993 5.0L Mustang style drive-by-cable throttle bodies * 2) 2020-2023 7.3L drive-by-wire throttle body * 3) 2020-2023 GT500 drive-by-wire throttle body (requires P/N 300-903) Compatible Engine Components: * 1) Factory accessories as well as Holley accessory drives (except for 20-380 and 97-409) * 2) Factory fuel rails and Holley 534-265 / 534-266 billet rails Intake manifold features: * Lower profile (2+ inches) than the OE intake manifold * Sturdy cast aluminum construction that will hold up to the elements and forced induction * Perfect complement to Holley's Godzilla accessory drive and oiling system (20-320 / 20-320BK / 20-340 / 20-340BK) for fitment into tight engine bays * Removable lower intake panel that can be removed for additional porting, nitrous, etc. * Incorporates long runners for solid low-end torque * Includes throttle body gasket and all necessary O-rings and adapters to mount to the engine * Compatible with OE or Holley accessory drives and OE or Holley fuel rails * Corrects OE throttle body angle by 55 degrees * Available in natural or black powdercoat finish
Not Yet Reviewed
$927.95
—
$949.95
$617.95
—
$834.95
On Sale
Weiand high-rise/dual-plane Speed Warrior intake manifolds feature long, separated runners for bottom-end and mid-range power, plus a special runner design and larger plenum to flow the air needed for high-rpm horsepower. They mount single, square-mount 4-barrel carburetors and make power from 1,500 to 6,700 rpm. That makes Weiand Speed Warrior intake manifolds the perfect choice for your street/strip vehicle. To make more power you have to get more air to your engine. Look to Weiand as your power source! Features include: * Permanent mold castings * Precision CNC-machined * Available with exhaust crossover for improved street drivability * Also available with isolated runners to reduce intake charge heating * Available finishes: as cast; polished; black ceramic coating; Everbright * Offered for standard small block Chevy heads, non-EGR 262 c.i.d. to 400 c.i.d. heads, and Vortec (L31) or non-Vortec heads
( 52 )
$299.95
—
$449.95
$224.95
—
$403.95
On Sale
Holley EFI LT1 Gen V Hi-Ram intake manifolds provide the ultimate performance with GM direct-injected Gen V 6.2L LT1 engines. The modular design allows easy disassembly for custom porting, multiple tops, or custom induction systems. Each runner has a large radius where it meets the plenum, and optimized taper and cross-sectional area to perform in a wide variety of engine configurations. When you look for the pinnacle of performance, price, and quality, look to Holley Hi-Ram intake manifolds for your LT1 application. Features include: * Available with injector bosses on the intake runners that provide increased performance potential by using additional injectors and the factory direct injection * Removable top * Large plenum volume * Intakes with injector ports include fuel rails with dual mounting * Fuel rails are anodized, laser-etched, and machined for -8 AN O-ring fittings at each end * Rear of plenum machined for MAP sensor and three vacuum ports * Head flange has clearance for fuel supply to a high-pressure pump * Increased runner wall thickness for custom porting at the plenum to runner entry on each runner * O-ring seals at cylinder heads and plenum top * Easy assembly with top-mounted screws on plenum top (except front two screws) * Several top options: 1 x 95mm, 1 x 105mm, 2 x 4150, 2 x 4500, or blank flange for custom throttle bodies * 3,500 to 8,000-plus rpm power band
( 2 )
$949.95
—
$1,299.95
$853.95
—
$1,168.95
On Sale
Holley EFI Gen III Hemi Hi-Ram intake manifolds are for high performance applications where induction system height is not limited. Able to add even more power to your engine, these manifolds have large intake ports and a modular base design with runner lengths and tapered cross-sections that will perform well for a wide range of engine configurations. Their aggressive, bold, race-bred styling will make bad intentions clear for drag race, muscle car, marine, off-road, sandrails, pulling trucks, track, and street-rod applications. Holley EFI Gen III Hemi Hi-Ram intake manifolds feature cast aluminum construction offered with a natural satin or black finish. They are available with either a 95 or 105mm LS-style throttle body or as the manifold base alone for custom induction systems. Features and benefits: * Modular design base accepts a wide range of EFI tops and can be used as the foundation for custom induction systems * EFI fuel rails are machined for -8 AN O-ring fittings with passages large enough to accommodate high fuel flow and dampen pressure pulsations in the fuel system * Intended for use on naturally aspirated, forced induction, or nitrous engines in the 5.7L to 7.2+L range, and maximum power at 7,500 to 8,500 rpm * Works with Gen III Hemi injectors and Bosch EV-1 style injectors * O-ring seal to head offer superior OE-style sealing and are easy to replace * Billet oil fill cap offers an attractive low-profile design * Positive Crankcase Ventilation (PCV) ports with adapter fittings * Port for OE-style Manifold Absolute Pressure (MAP) sensor (1 or 2 Bar) * Cast-in pads for adding nitrous nozzles
( 2 )
$949.95
—
$1,499.95
$853.95
—
$1,348.95
On Sale
Our Summit Racing™ cast aluminum intakes are the perfect performance upgrades for your engine. The dual plane carbureted manifolds feature a runner design to deliver improved power. They're available in a variety of sizes, RPM ranges, and finishes. Order the model recommended for your vehicle application.
( 50 )
$328.99
—
$340.99
$228.99
—
$240.99
On Sale
Holley SBF Hi-Ram EFI intake manifolds with side-mount tops are available for the 8.2 in. or 9.5 in. SBF Ford applications, and come with either a 95mm or 105mm Ford 5.0L throttle body flange side-mount top. The runner length and tapered cross-section design will perform well for a wide range of engine configurations. Holley's engineering team redesigned the water crossover passage to allow room for distributor phasing. The SBF Hi-Ram EFI intake manifolds have aggressive, bold, race-bred styling that's perfect for drag race, muscle car, off-road, pulling trucks, street rod applications, and more! Additional features and specs include: * Cast aluminum construction with satin silver finish * Designed for side-mounted throttle bodies (Ford 5.0L throttle body fitment) * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system; they come standard with EFI Hi-Ram kits * Plenum top gasket type: 3/32 in. round O-ring cord * Allows room for designing boosted applications * A low-profile distributor will be needed when using this manifold
Not Yet Reviewed
$1,249.95
—
$1,299.95
$687.95
—
$1,123.95
On Sale
Make Holley SBF Hi-Ram EFI intake manifold bases the foundation for your custom induction system. Their modular design allows them to accept a variety of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. Aggressive looks and bold styling make your bad intentions clear—whether you're drag racing, truck pulling, or making waves in your boat—when you start with the Holley Hi-Ram EFI intake manifold bases. SBF Hi-Ram EFI intake manifold base features and specs: * Manifold base only designed for 8.2 in. deck height * Cast aluminum construction * Available in natural cast aluminum (satin) or black powdercoat finish * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system
( 1 )
$996.95
—
$1,049.95
$648.95
—
$682.95
On Sale
Edelbrock Pro-Flo XT EFI intake manifolds combine a user-friendly design with the latest technology. They're manufactured from aluminum and are available in a natural, polished, or black powdercoat finish for ultimate protection. Pro-Flo XT EFI intakes feature eight equal-length tapered runners and a large plenum. The fuel-injected manifolds are designed to deliver maximum horsepower and a broad torque curve throughout the 1,500 to 7,000 rpm range. Choose the model designed for your vehicle and cylinder head style application.
( 15 )
$637.95
—
$945.95
$510.36
—
$756.76
On Sale
Holley Strip Dominator intake manifolds are classics that have been making power for Chevys for almost as long as Holley has been making carburetors. They're proven power builders, engineered to achieve maximum performance. Their single plane design, with a deep, open plenum and isolated runners, produces good power from 4,500 rpm to 7,600 rpm for small blocks, and up to 8,500 rpm on big blocks. There is no exhaust heat crossover.
( 35 )
$399.95
—
$471.95
$359.95
—
$423.95
On Sale
Holley EFI Gen V LT single plane intake manifolds are designed with an optimized runner layout and a constant cross-sectional area, resulting in a broad torque curve with the best vehicle performance from 2,500 to 7,000 rpm. The single-plane design provides the lowest throttle body flange height possible, while providing maximum performance all the way to 7,000 rpm. The cast aluminum construction makes these manifolds great choices for centrifugal blowers, turbochargers, or NOS applications. They are sold for pre-emissions control applications only and will not accept stock components and hardware. Available in two finishes, choose the one you prefer. Features: * Optimized runner layout and constant cross sectional area--broad torque curve * Minimum carburetor flange height--fit in vehicles with minimum hood modifications * Provides classic engine bay look of carburetor-style intake * Cast aluminum construction--great manifold for centrifugal blower, turbocharged, or NOS mild power adder applications * Efficient casting design--lightweight, consistent wall thicknesses, improved casting quality * Weight: 11.5 lbs. * Height: (front) 5.417 in. to the lifter valley cover flange at the engine block front flange and bellhousing flange * Port size: 2.33 in. height x 1.27 in. wide * FKM O-ring intake to cylinder head gaskets Notes: These intake manifolds are meant for GM Gen V LT engines equipped with OE-type GM Gen V LT cylinder heads where the intake flange bolt pattern and intake port opening locations match the OE Gen V LT port configuration. They are intended for OE direct injection and a 4150 EFI throttle body. Holley accessories available to allow the installation of a GM LS 92mm or 105mm drive-by-wire throttle body. Holley EFI Gen V LT 300-940 manifold is meant for street and performance engine applications with 5.3 to 6.2+ liters of displacement and maximum engine speeds of 6,000 to 7,000 rpm (depending on the engine combination). 4150/4160 square bore flange.
Not Yet Reviewed
$449.95
$403.95
On Sale
Holley EFI Coyote Ultra Lo-Ram intake manifolds are designed to fit stock bolt pattern OE heads found on the 2011-23 Ford 5.0 Coyotes and related engine families, such as Voodoo and Predators. These kits include fuel rails for use with OEM-type fuel injectors and clips, mounting hardware, and O-ring gaskets. Offered in black and natural as-cast finish, the manifolds have a 9.20 in. runner length and are designed to improve the mid to high RPM powerband. The Ultra Lo-Ram provides an additional 19.4mm front and 42.6mm rear clearance compared to the Ford Performance Cobra Jet manifold—plus clears 2015-23 Mustang factory hoods. They're offered in both round and oval throttle body configurations, with replacement front inlets for easy interchangeability. The oval inlet can accommodate up to a 150 x 66mm single throttle body and 93mm on the round variant. Round inlets include standard mounting provisions for GT350, GT500, and LS 4-bolt throttle bodies. 2011-23 GT throttle bodies can be used with the optional 717-18 adapter. (NOTE: Coyote Ultra Lo-Ram intake manifolds are available with the base only, no top included, if desired. See "Intake Section Included" tabs.) Product features: * As-cast aluminum construction: more durable for boosted applications, can be welded for modifications * Modular design: accessible runner entries for porting, allows accessories like intercoolers and nitrous plates * 300-911 and 300-912 Ultra Lo-Ram will fit under stock hood with stock engine mounts in 2015-23 Mustang * Refined port design with streamlined injector boss for reduced turbulence without loss of flow area * Allows a variety of throttle valves, including large monoblade, 2015-20 GT350, 2007-14 GT500, 2019-23 GT500, GM LS 4-bolt, 2011-23 Ford Mustang GT (with optional adapter PN 717-18) * Fuel rails with -8 AN ports and dual 1/8 NPT accessory ports for gauges or Gen 3 direct injection fuel line hookup
( 1 )
$924.95
—
$949.95
$508.95
—
$853.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
