Availability
Tremec offers a variety of TKX 5-speed manual transmission for select GM and Ford applications. Each model features different gear ratios. Order the transmission best suited for your vehicle. General product details: * Bolts up to a standard GM Muncie bellhousing or use a Quicktime bellhousing * Input Shaft: 26-Spline (requires 26-spline clutch disk) * Output Shaft: 31 Spline * The TKX has 600 lbs.-ft. of torque capacity and is capable of engines speeds of 8,000 rpm with shifts at 7,500 rpm. It is available in multiple gear ratio configurations. * Designed for multiple applications with three shifter locations. Compact, end-loaded design provides clearance in most transmission tunnels without floor * Increased case strength with 3-piece aluminum housing provides outstanding structural stiffness (includes main case, intermediate plate and rear extension). Gaskets at all flanges simplifies installation and eliminates fluid * Superior shift-ability through use of multi-cone synchronizers and hybrid synchronizer rings made of sintered bronze and carbon * Noise, vibration and harshness (NVH) minimized with gear layout to best control stress All gears supported by caged needle bearings to reduce end play on the gears. * All gears and shafts made from special grade steel (ASTM 4615), providing increased torque carrying * Equipped with a high performance short-throw billet aluminum shifter that isolates road noise, while providing clean, crisp * Robust design with internal 3-rail shift system and steel shift * Wide gear width increases gear life and torque * Built-in reverse light switch and cruise control safety
( 44 )
$2,999.99
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L80E Level 4 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 800 hp * Up to 700 lb.-ft. of torque * Stall: 2,800 to 3,400 * Custom-built, custom-stalled 10 in. billet racing lock-up converter * Master overhaul kit with Alto hardened steels * Raybestos Stage 1 frictions * TransGo reprogramming kit * Filter * Torrington bearing kit * Bushing kit * Thrust washer kit * Internal wiring harness * New manifold pressure switch * New EPC solenoid * New PWM solenoid * New input and output speed sensors * New 1-2 and 3-4 shift solenoids * Expanded capacity forward clutch drum * Extra-capacity 2nd gear clutch assembly * Expanded capacity 3rd clutch drum * Heat-treated input shaft * 300M main shaft * 300M forward clutch hub * Updated molded steel direct clutch piston * Updated reverse band * New low roller assembly * Wide kickdown band with new apply piston * Heavy-duty intermediate sprag * Updated boost valve * Updated TCC regulator valve * Blueprinted pump and valve body * Transmission mount * New OEM steel pan
( 1 )
$7,845.00
American Powertrain ProFit Tremec TKX manual transmissions and installation kits put the power to the pavement with unmatched durability and versatility. Tremec has normally sourced their aftermarket transmissions from the OE side, such as the Magnum T-56 and the T-5, but this new design is made from the ground up as a strictly aftermarket transmission. Designed to fit classic muscle cars and customs, the TKX has a tighter, more streamlined case, and features 600 lbs.-ft. of torque capacity and are capable of engines speeds of 8,000 rpm with shifts at 7,500 rpm. The compact design provides clearance in most transmission tunnels without floor modifications, while case strength has increased from previous models with the new 3-piece aluminum housing and gaskets at all flanges simplifies installation and eliminates fluid leaks. Additional features include: * Designed with your specific vehicle application in mind * Available with multiple gear ratio configurations for compatibility for multiple applications with three shifter locations * Multi-cone synchronizers and synchronizer rings are made of sintered bronze and carbon for superior shifts * All gears are supported by caged needle bearings to reduce end play * Gears and shafts are made from ASTM 4615 grade steel and provide increased torque carrying capacity * TKX manual transmissions have 31-spline output shafts for added strength, built-in reverse light switches, and cruise control safety switches * The TKX also has separate GM and Ford case patterns and input configurations—with integrated GM and Ford transmission mount patterns * Installation kits include a driveshaft slip yoke made from cryogenically hardened steel, a polyurethane transmission mount, a steel roller pilot bearing, and a reverse light wiring harness
( 1 )
$3,995.95
—
$4,559.95
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L65E Level 3 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 500 hp * Up to 500 lb.-ft. of torque * Stall: 2,600 to 3,200 * High performance 12 in. furnace-brazed converter -- Flanged hub and carbon fiber clutch * Master overhaul kit with Alto hardened steels * Raybestos Stage 1 frictions * Filter * 29-element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings * New 13-vane pump rotor * New vanes * New stator * .500 boost valve * Pressure regulator valve * Updated boost valve * TransGo reprogramming shift kit with Shift Command * Bushing kit * New thrust washers * Complete Torrington bearing kit * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * High-rev spring kit * Corvette servo * Carbon fiber wide 2-4 band * New valve body spacer plate * Fill tube and stick * New shift solenoids * New EPC solenoid * New PWM solenoid * New 3/2 solenoid * New manifold pressure switch * New internal wiring harness with new TCC solenoid * New electronic speed sensor * Transmission mount * New OE steel transmission pan
Not Yet Reviewed
$4,945.00
—
$5,945.00
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L65E Level 4 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 650 hp * Up to 600 lb.-ft. of torque * Stall: 2,600 to 4,000 * Custom-built and custom-stalled 10 in. or 11 in. billet racing lock-up converter * Master overhaul kit with Alto hardened steels * Raybestos Gen II racing frictions * Filter * 29-element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings * New 13-vane pump rotor * New vanes * New stator * .500 boost valve * Pressure regulator valve * Updated boost valve * TransGo reprogramming shift kit with Shift Command * Complete Torrington bearing kit * Bushing kit * Thrust washers * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * High-rev spring kit * 5-pinion heavy-duty front and rear planetary gear sets with sun gear * Hardened output shaft * Hardened reaction shaft and hub * Super hold 4th servo * Corvette servo * Wide carbon fiber wide 2-4 band * New internal wiring harness with new TCC solenoid * New shift solenoids * New EPC solenoid * New PWM solenoid * New 3/2 solenoid * New manifold pressure switch * New electronic speed sensor * New valve body spacer plate * New OE steel transmission pan * Transmission mount
( 2 )
$5,945.00
—
$6,945.00
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L80E Level 3 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 600 hp * Up to 600 lb.-ft. of torque * Stall: 2,600 to 3,600 * Custom-built 10 in. billet racing lock-up converter * Master overhaul kit with Alto hardened steels * Raybestos Stage 1 frictions * TransGo reprogramming kit * Filter * Torrington bearing kit * Bushing kit * Thrust washer kit * Internal wiring harness * New manifold pressure switch * New EPC solenoid * New PWM solenoid * New input and output speed sensors * New 1-2 and 3-4 shift solenoids * Expanded capacity forward clutch drum * Extra-capacity 2nd gear clutch assembly * Expanded capacity 3rd clutch drum * Heat-treated input and main shafts * Heat-treated forward steel clutch hub * Updated molded steel direct clutch piston * Updated reverse band * New low roller assembly * Wide kickdown band with new apply piston * Heavy-duty intermediate sprag * Updated boost valve * Updated TCC regulator valve * Blue printed pump and valve body * Transmission mount * New OEM steel pan
Not Yet Reviewed
$6,845.00
On Sale
Auburn Gear Select-A-Loc differentials maximize your vehicle's traction with on-the-go system engage. These electronically controlled traction-enhancing differentials are selectable lockers offering the traction control of a limited-slip differential and a full-locking differential--all in one! When locker switch is off, the clutch pack activates the limited-slip mode. As torque increases, the separating forces within the differential gears increase, causing the clutch pack to be compressed, in turn providing bias torque to the highest traction wheel. When the locker switch is turned on, electronic current is sent to the electromagnetic coil which locks the axles together. Auburn Gear Select-A-Loc lockers feature a unique cone-clutch design with gearing made from aircraft-quality 9310 heat-treated billet steel for tough-as-nails strength. The lockers operate quietly without any shift fork or pins to line up to change the locker mode. With a limited-slip mode for on/off-road excitement and a true locker mode for the quarter-mile or nasty off-road terrain, Auburn Gear Select-A-Loc differentials deliver superior traction capabilities on the street, at the track, or off-road.
( 10 )
$1,339.99
—
$1,444.99
$1,205.99
—
$1,300.49
On Sale
A 4x4 and traction go hand-in-hand; however, standard (open) differentials allow each wheel to turn independently to eliminate binding in turns. Off-road, this becomes a problem as engine power takes the path of least resistance—to the wheel with little or no traction. Limited slip differentials offer some improvement, but too often the slipping is not "limited" enough to maintain forward progress. Automatic locking differentials also have disadvantages; noisy when disengaging, they can also upset on-highway driving characteristics. Created to provide traction on demand, without sacrificing highway driving performance, ARB Air Locker differentials employ a 12 V ARB air compressor (sold separately) to pneumatically operate a solid and durable locking mechanism inside the differential. When activated, the Air Locker prevents the differential gears from rotating and the axle shafts from turning independently of each other. With both wheels tied directly to the rotation of the ring gear, the vehicle maintains maximum possible traction at all times. When unlocked, it operates just like a conventional open differential. ARB Air Lockers are available in over 100 configurations for a wide range of vehicles and can be installed in both front and rear axles. Installation should be performed by a qualified differential technician, although no special tools or skills are required, apart from those necessary for fitting a standard differential. ARB also offers three compressor models suitable for Air Locker operation, two of which can be used to inflate tires and operate other equipment. Additional features of ARB Air Lockers include: * Vastly improved traction means less reliance on momentum, reducing the likelihood of vehicle damage * Easy, convenient operation without leaving the comfort and safety of the driver's seat * Ultra durable and extremely strong; only the highest quality materials used in construction * Patented gear technology and 2-piece design ensures optimal locking strength * Forged gears provide superior strength and durability * Incredibly simple, yet effective, design employs minimal moving parts for maximum reliability * Thoroughly tested and proven * Most sold as kits with differential, activation switch, solenoid valve, air line, and bulkhead fittings * Front and rear Air Lockers available for most makes and models * For 4WD and 2WD applications * Easy maintenance; no special additives required * Also offered in ARB Traction Packs that include two Air Lockers, a compressor, and accessories for tire inflation
( 11 )
$1,299.95
$1,104.96
On Sale
Need traction? Zip! You've got it with Yukon Gear & Axle Zip lockers! With on-demand traction, these lockers offer an air-operated design that allows you to switch from an open differential to 100 percent lockup when you need it. Theses Yukon Zip lockers are the ultimate in driver selectability for the right traction, on-road and off. Built from forged cases with 4320 chromoly internals for added strength, they work with a variety of air-delivery systems and are assembled in the USA. Do you need gripping power--now? You have the control with Yukon Gear & Axle Zip lockers.
( 1 )
$1,539.99
$1,308.99
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L60E Level 3 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 500 hp * Up to 500 lb.-ft. of torque * Raybestos Stage 1 frictions and steels * TransGo heavy-duty reprogramming kit with Shift Command * Filter * 29-element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings * New 10-vane pump rotor * New vanes * New stator * .500 boost valve * Pressure regulator valve * Updated boost valve * TransGo reprogramming shift kit with Shift Command * Bushing kit * New thrust washers * Complete Torrington bearing kit * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * High-rev spring kit * Corvette servo * High-energy wide bands * New valve body spacer plate * Fill tube and stick * New shift solenoids * New EPC solenoid * New PWM solenoid * New 3/2 solenoid * New manifold pressure switch * New internal wiring harness with new TCC solenoid * New electronic speed sensor * Inspection cover (chrome) * Transmission mount * New OE steel transmission pan
Not Yet Reviewed
$4,945.00
—
$5,445.00
Advance Adapters offers an AX15 5-speed transmission retrofit adapter kit for 1966-77 Bronco Dana 20 applications. The adapter kit comes complete with the conversion components required to retrofit your early Ford Bronco with the Aisin AX15. Kit includes: * New AX15 transmission * Transfer case adapter and transfer case shifter linkage bracket (T-style shifter only) * Transmission to engine adapter * Clutch disc * Crossmember mount kit * Shifter handle * The Transmission: This transmission is manufactured by Aisin Warner. The overall transmission case length is 24.000 in. The output shaft on this transmission is 23-spline and protrudes approximately .400 in. This transmission is normally found coupled to the AMC 4.0L 6-cylinder engine and seems to be one of the better transmissions Jeep used—very capable of handling the horsepower and torque of a V8 engine. * The Vehicle background and specs: The early Ford Broncos have always been a popular vehicle for conversions. These vehicles were normally equipped with a 6-cylinder or V8 engine up to a 3-speed transmission. On this transmission, Ford used two different lengths of adapter housings when coupling this 3-speed to the stock transfer case. The adapter housing is either 6 1/2 in. or 9 3/8 in. Vehicles equipped with a V8 had a 9 3/8 in. tailhousing which set the bellhousing further into the engine compartment. Vehicles with the 6-cylinder had a 6 1/2 in. tailhousing. This shorter adapter compensated for the longer engine. In 1973, Ford began offering the C4 automatic. A special tailhousing and output shaft was manufactured to couple this transmission to the stock transfer case. Ford no longer makes the C4 adapter. The 1966-77 vehicles were equipped to a Bronco Dana 20 transfer case. This transfer case, unlike the Jeep Dana 20, has the front driveshaft on the driver's side of the vehicle. The input gear of this transfer case is 6-spline. Ford always used a spud shaft that coupled this 6-spline transfer case to the transmission 28-spline. The transmission-to-transfer case adapters used both a dowel pin and alignment retainer. The spud shaft is supported in this retainer with a bearing. Advance Adapter adapter kits utilize this type of design. In some applications, the stock spud shaft is also retained. This transfer case has a 2.46:1 low gear ratio. In early 1973, Ford switched to a 2.34:1 low gear ratio. These transfer cases used two different shifter designs known as either the "J" pattern or "T" handle. The "T" handle was used from 1966 to 1972, and the "J" pattern from 1973 to 1977. The "T" handle shifter is a fairly simple shifting mechanism; and to retain it with an adapter only requires a pivot point for mounting. The "J" shifter requires the shift handle to be mounted in a location relatively close to its stock position. Retaining this shifter is hard to accomplish when adapting the various transmissions to the Dana 20. Vehicle owners with a "J" shifter are advised to either change the transfer case shifter rods and go to a "T" style shifter, or to contact one of the Bronco specialty shops that offer a twin stick replacement for the "J" shifter. A twin stick shifter replacing the "J" style should work with most of Advance adapters. Advance Adapter housings normally utilize the stock Bronco crossmember with the stock rubber supports. On new transmission assemblies longer than stock, this crossmember may need to be relocated. There are a few adapters that require this crossmember to be modified. These modifications are noted in detail on the specific adapter instruction sheet.
Not Yet Reviewed
$3,141.50
When you order a Lokar cable-operated automatic transmission shifter, you know you're buying quality. They're manufactured to deliver outstanding performance and safety with their patented Safety Lock-Out button. This button prevents accidental shifting from park into reverse, drive, and low gears. Other important features include: a neutral safety switch; 360 degree lever rotation for extra leg room; a completely adjustable mounting bracket that allows for a wide range of installation positions; and your choice of a brushed aluminum mushroom, black anodized mushroom, or high-tech tapered shift knob. These Lokar shifters use a short shifter cable, eliminating the problem of time-consuming linkage adjustments. Available for many different types of automatic transmissions, the shifters are perfect for your car, truck, hot rod, or street rod. Options include stick length, type, and finish; and knob style, material, and finish.
( 23 )
$643.95
GearStar GM high-performance transmissions are built to meet the horsepower, torque, and rear gear ratio demands of the engines they will be matched to. Unlike other high-performance transmissions these models are hand-built by one technician from start to finish. Before a transmission and torque converter leaves the facility, they are dyno-tested for the equivalent of 100 miles, ensuring proper working conditions. GearStar GM 4L65E Level 4 transmissions and included torque converters are built with the highest-quality parts available to provide heart-pounding performance with industry-leading experience. Choose the Level 4 transmission best suited for your build and strap yourself into the experience of uncompromising performance with the legendary road-proven craftsmanship of GearStar Performance transmissions! More product features, items, and specifications may include: * Versions of up to 650 hp and up to 600 lbs.-ft. of torque at the crankshaft * Raybestos Stage 1 frictions and steels, high-energy wide bands * Two TransGo recalibration shift kits with Shift Command * OE-style filter and new internal wiring harness with new TCC solenoid * New shift solenoids, EPC solenoid, PWM solenoid, and 3/2 control solenoid * New manifold pressure switch, electronic speed sensor, and valve body spacer plate * Corvette servo and Super Hold 4th gear servo * New Torrington bearings * Bushing kit and thrust washer or thrust washer kit * Dual cage sprag (29-element) * High-capacity multi-vane pump assembly with new rotor (some with slide) * Hardened stator shaft, new vanes, and hardened rings * Updated boost valve * Pressure regulator valve * Extra-capacity, heavy-duty drum assembly * Heavy-duty 5-pinion steel planetary gear sets * Transmission pan
Not Yet Reviewed
$5,945.00
—
$6,445.00
GearStar offers GM 4L65E Level 4 C5/C6 transmissions for a variety of rear-wheel-drive applications, including many Chevy small block Gen III/IV (LS-based) engines from 1997 and up. Performance specs: 650 hp and up to 650 lbs.-ft. torque. Transmission details: * Converter: 10 in. custom built lock-up Billet Racing * Stall: 2,600-4,500 * 1,300-2,600 stall available for diesel and 4X4 * Master overhaul kit with alto hardened steels * Raybestos Gen II racing frictions * High-flow filter * New 29 element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings * New 13 vane pump rotor * New vanes * New stator * .500 boost valve * Pressure regulator valve * Updated boost valve * Transgo reprogramming shift kit with shift command * Gearstar full race shift kit * Bushing kit * New thrust washers * Complete Torrington bearing kit * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * Input shaft * High rev spring kit * Heavy-duty 5 pinion front and rear planetary gear set with sun gear * Fully rollerized gear train assembly with sun gear * New Low/ Rev heavy-duty spring and roller with 300M bearing race * Super hold 4th servo * Corvette servo * Wide carbon fiber 2-4 band * New valve body spacer plate * New shift solenoids * New EPC solenoid * New PWM solenoid * New 3/2 solenoid * New manifold pressure switch * New internal wiring harness with new TCC solenoid * New electronic speed sensor * Transmission mount
Not Yet Reviewed
$6,245.00
GearStar offers GM 4L70E Level 4 transmission models for a variety of rear-wheel-drive and four-wheel-drive applications, including many Chevy small block Gen III/IV (LS-based) engines from 1997 and up. They're available in different flash stall ratings. Performance specs include: 650 hp and up to 650 lbs.-ft. torque. Transmission details: * Converter: Custom built and custom stalled 10 or 11 in. lock-up Billet Racing * Stall: 1,600-3,600 * Master overhaul kit with alto hardened steels * Raybestos Gen II racing frictions * High-capacity filter * New 29 element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings * New 13 vane pump rotor * New vanes * New stator * .500 boost valve * Pressure regulator valve * Updated boost valve * Transgo reprogramming shift kit with shift command * Bushing kit * New thrust washers * Complete Torrington bearing kit * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * High rev spring kit * Heavy-duty 5 pinion front and rear planetary gear set with sun gear – AC Delco * 300M hardened output shaft * 300M hardened reaction shaft and hub * Super hold 4th servo * Corvette servo * Wide carbon fiber 2-4 band * New valve body spacer plate * New shift solenoids * New EPC solenoid * New PWM solenoid * New 3/2 solenoid * New manifold pressure switch * New internal wiring harness with new TCC solenoid * New electronic speed sensor * Inspection cover (polished aluminum) * New original equipment steel transmission pan * Transmission mount * This transmission requires the use of a standalone controller in non-OEM applications * All transmissions are custom built by one of five master techs from start to finish—and DYNO tested with converter the equivalent of 100 miles to ensure that transmission and converter package are in perfect operating condition before they leave the GearStar facility.
Not Yet Reviewed
$6,145.00
—
$6,645.00
GearStar offers GM 4L805E Level 5 transmissions for a variety of rear-wheel-drive and four-wheel-drive applications. They are compatible with Chevy small block Gen III/IV (LS-based) engines from 1997 and up; and select Chevy small block Gen 1 and big block Gen V, Gen VI, and Mark IV engines from 1955 and up. Performance specs include between 800 and 1,000 hp and up to 900 lbs.-ft. torque, depending on model. Transmission details: * Converter: Custom built and custom stalled 10 in. lock-up Billet Racing * Stall: 2,800-3,600 * Master overhaul kit with alto hardened steels * Raybestos Stage I frictions * Transgo reprogramming kit * Filter * New Torrington bearing kit * New bushing kit * New thrust washer kit * New internal wiring harness * New manifold pressure switch * New EPC solenoid * New PWM solenoid * New input and output speed sensors * New 1-2 shift solenoid * New 3-4 shift solenoid * Expanded capacity forward clutch drum * Extra capacity second gear clutch assembly * Expanded capacity third clutch drum * Heat treated input shaft * 300M main shaft * 300M forward clutch hub * Updated molded steel direct clutch piston * Updated reverse band * New low roller assembly * Wide kickdown band with new apply piston * Heavy-duty intermediate sprag * Updated boost valve * Updated TCC regulator valve * Blue printed pump and valve body * Transmission mount * New OEM steel pan
Not Yet Reviewed
$9,345.00
GearStar offers GM 4L85E Level 3 transmissions for a variety of rear-wheel-drive applications, including many Chevy small block Gen III/IV (LS-based) engines from 1997 and up. Performance specs include: 1,000 hp and up to 1,000 lbs.-ft. or torque. Transmission details: * Converter: Custom built and custom stalled 10 or 11 in. billet Yank Racing * Stall: 2,600-3,600 * Master overhaul kit * Raybestos Racing Blue Gen II frictions * High-flow filter * 2 Transgo reprogramming shift kits * GearStar full race shift kit * High energy wide bands * New bearing kit * New bushing kit * New thrust washer kit * New low roller sprag * 300M hardened input shaft * 300M hardened intermediate shaft * 300M forward hub * High-capacity pump assembly with new gears * New 5 pinion reaction planetary gear set * New 5 pinion low planetary gear set * Extra capacity 2nd gear clutch assembly * Extra capacity 3rd gear super drum with wide heavy-duty sprag, race, and modified plates * Custom machined billet forward and direct drum pistons * Heavy-duty 2nd gear apply piston * New shift solenoids * New EPC solenoid * New PWM solenoid * New manifold pressure switch * New input and output speed senor * New internal wiring harness * Updated boost valve * Updated TCC regulator valve * Blueprinted pump and valve body * Transmission mount * This transmission requires the use of a standalone controller in non-OEM applications * All transmissions are custom built by one of five master techs from start to finish and DYNO tested with converter the equivalent of 100 miles to ensure that transmission and converter package are in perfect operating condition before they leave the GearStar facility.
Not Yet Reviewed
$10,045.00
GearStar offers GM 4L85E Level 4 transmissions for a variety of rear-wheel-drive applications. They are compatible with Chevy small block Gen III/IV (LS-based) engines from 1997 and up; and select Chevy small block Gen 1 and big block Gen V, Gen VI, and Mark IV engines from 1955 and up. Performance specs include 1,500 hp and up to 1,500 lbs.-ft. of torque. Transmission details: * Converter: Custom built and custom stalled 10 or 11 in. billet yank racing * Stall: 2,600-3,600 * Master overhaul kit with alto hardened steels * Raybestos Racing Blue Gen II frictions * High-flow filter * 2 Transgo reprogramming shift kits * GearStar full race shift kit * Carbon fiber heavy-duty reverse band * Wide carbon fiber kickdown band * New bearing kit * New bushing kit * New thrust washer kit * New low roller sprag * 300M hardened input shaft * 300M hardened intermediate shaft * 300M forward hub * High-capacity pump assembly with new gears * New 5-pinion reaction planetary gear set * New 5-pinion low planetary gear set * Extra capacity 2nd gear clutch assembly * Extra capacity 3rd gear super drum with wide heavy-duty sprag, race, and modified plates * Custom machined billet forward and direct drum pistons * Heavy-duty 2nd gear apply piston * New shift solenoids * New EPC solenoid * New PWM solenoid * New manifold pressure switch * New input and output speed senor * New internal wiring harness * Updated boost valve * Updated TCC regulator valve * Blueprinted pump and valve body * Transmission mount * This transmission requires the use of a standalone controller in non-OEM applications * All transmissions are custom-built by one of five master techs from start to finish and DYNO tested with converter the equivalent of 100 miles to ensure that transmission and converter package are in perfect operating condition before they leave the GearStar facility.
Not Yet Reviewed
$11,045.00
Gearstar GM 4L65E Level 4 transmissions for the GM LT4 engine are designed for strength and durability. Built with heavy-duty and upgraded components, these 4L65E transmissions are able to handle the torque from your custom build. All Gearstar transmissions are custom built by master technicians from start to finish and dyno tested with converter for the equivalent of 100 miles. They do this to ensure the transmission and converter package are in perfect operating condition before they leave the factory. Features: * Maximum 650 hp and 650 lb./ft. of torque * Yank Performance custom billet lock-up compatible torque converter * LT4 bellhousing * Master overhaul kit with Alto hardened steels * Raybestos Gen II racing frictions * High-flow filter * New 29 element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings,13-vane pump rotor, and stator * 0.500 updated boost valve * Pressure regulator valve * Transgo reprogramming shift kit with shift command * Bushing kit * New thrust washers and complete Torrington bearing kit * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * High-rev spring kit * Heavy-duty 5-pinion front and rear planetary gear set with sun gear * Hardened output shaft and reaction shaft and hub * Super hold 4th gear servo * Corvette servo * Wide carbon fiber 2-4 band * New valve body spacer plate * New shift solenoids, EPC solenoid, PWM solenoid, and 3/2 solenoid * New manifold pressure switch * New internal wiring harness and TCC solenoid * New electronic speed sensor * New Original Equipment transmission pan * Transmission mount * Also includes an external transmission cooler, bellhousing bolts, torque converter bolts, and all required fluid
Not Yet Reviewed
$6,245.00
Zumbrota remanufactured manual transmissions are some of the most dependable 5-speed, 6-speed, and transaxle units available. Each transmission is put through tremendous testing and inspections to assure the highest quality possible to use in your vehicle. Benefits of Zumbrota remanufactured manual transmissions include: * A pre-inspection is done to ensure the unit is free of case cracks, excessive wear and to catch other OEM related problems that many cores have * A second inspection is conducted during the remanufacturing process to ensure all component parts meet OEM specifications * A final post-build inspection is done to ensure unit is built to their strict standards * All units are quality inspected throughout the remanufacturing process to maintain our quality standard * All housing and top covers are cleaned utilizing their state-of-the-art hydro-blasting and rinsing process--this brings all cases back to the OEM finish * 100 percent inspection of internal parts, including gear wear checks, main shaft straightness test and synchronizer testing * 100 percent replacement of seals, bearings, and other common wear components * Units are shipped in high-density plastic totes to help eliminate in-transit damage * All transfer cases are sold with a standard 2 year/unlimited mileage warranty
( 19 )
$1,157.99
—
$1,901.99
Zumbrota remanufactured transfer cases are put through a proprietary cleaning method, and arrive looking like new. But before they ship, each unit goes through complete inspection, component replacement, and quality control process to assure dependable, reliable shift-ability. Zumbrota rebuilds units from New Process, Borg Warner, and other major manufacturers to fill fitments for foreign and domestic passenger cars, trucks, and SUVs. Benefits of Zumbrota remanufactured transfer cases include: * A pre-inspection is done to ensure the unit is free of case cracks, excessive wear and to catch other OEM related problems that many cores have * A second inspection is conducted during the remanufacturing process to ensure all component parts meet OEM specifications * A final post-build inspection is done to ensure unit is built to their strict standards * All units are quality inspected throughout the remanufacturing process to maintain our quality standard * All cases are cleaned utilizing their state-of-the-art hydro-blasting and rinsing process--this brings all cases back to the OEM finish * 100 percent replacement of seals, bearings, viscous couplers (when applicable), and other common wear components * Units are shipped in high-density plastic totes to help eliminate in-transit damage * All transfer cases are sold with a standard 2 year/unlimited mileage warranty
( 7 )
$1,378.99
—
$2,001.99
Dorman driveshafts are designed to replace your factory originals with no modifications. They are manufactured from quality materials and have the stock connections for an easy bolt-in fit. The driveshafts are available in various lengths, diameters, and materials for many auto, truck, and SUV applications.
( 320 )
$324.99
—
$568.99
Richmond Gear Super Street 5-speed transmissions feature a 5-speed design with overdrive that can handle up to 600 ft.-lbs. of torque. Based on the successful Richmond NASCAR-type design and technology, they are manufactured using the best in CNC machining, gear-cutting technology, and race-proven in-house treating. These transmissions include a long shifter for the ultimate in shift performance and durability. Available for Ford or GM applications, Richmond Gear Super Street 5-speed transmissions will make an excellent addition to your vehicle.
( 5 )
$4,434.99
Zumbrota Drivetrain remanufactured axle assembles offer reliable performance at a value price. They're available for thousands of applications—from passenger and off-road vehicles, to race cars and pulling trucks. The axle tubes are straightened to OE specifications; the housings are hydro-blasted and rinsed, then tested for surface wear and cracks; and the gear patterns and rolling torque are properly adjusted to ensure optimum tooth contact. Zumbrota replaces all seals, bearings, crush sleeves, pinion nuts, and shims on the front and/or rear axle assemblies. Order the replacement model recommended for your specific vehicle.
( 9 )
$1,090.99
—
$1,664.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
