Availability
Showing In Stock Items. Show All 16 Items.
TCI Maximizer high-torque towing converters are efficient units that put more of your engine's torque to the ground. Slippage is minimized, providing better gas mileage and as much as a 20-degree F reduction in transmission temperature. Another benefit is reduced engine rpm at highway speed. These torque converters are available in a variety of size options for more than a dozen Chevy, Ford, and Mopar transmission models.
( 20 )
$855.95
These Maximizer Street Performance torque converters are built with extra reinforcement and thicker mounting surfaces to withstand the additional load and vibration put through the drivetrain by a truck with performance modifications. By providing additional stall, your truck will see better initial takeoff and will not lug the engine when using big tires. Special attention is made to match the converters to the power range of most trucks that do double duty as off-road and daily drivers. Improved rear-wheel horsepower and elapsed times are some of the results.
( 7 )
$786.95
Tow Master series torque converters from Hughes Performance are designed to increase bottom-end pulling power in your tow vehicle without sacrificing top-end efficiency or lockup. Because they offer your vehicle more power with less effort, mileage can be increased by as much as 1-2 miles per gallon. Recommended for slightly modified engines, these Tow Master converters help you get the job done. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 25 )
$865.99
—
$891.99
On Sale
B&M Traveler torque converters are designed for use in motor homes, tow vehicles, or other heavy-duty applications where a slightly higher stall speed is helpful in getting the vehicle moving. Stronger than a stock converter, these Travelers have been internally modified to provide about 300 rpm more stall speed. This helps in initial acceleration without sacrificing normal highway operation. Pressure tested, fully balanced, and manufactured for long life, these Traveler converters will get you moving and on your way.
( 3 )
$899.95
$808.95
Street Master torque converters are designed for the driver who is looking for a competitive advantage. By raising the stall rpm, these converters will completely eliminate slow, sluggish starts. Recommended for stock to slightly modified engines for maximum performance, they'll allow the engine to idle smoothly when the car is in gear. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 r.p.m. lower.
( 235 )
$852.99
—
$964.99
For all of your driving needs, you'll enjoy the strength and feel of FTI Performance Diesel BA Series torque converters. These units include billet front covers, heavy-duty sprag modifications, and furnace-brazed and TIG-welded fins. Their single disc works great for everyday driving and moderate towing. BA Series converters provide more torque multiplication, lower transmission temperatures, improved acceleration—and when you can keep your right foot under control, better fuel mileage! Give your pickup truck the power to control your ride with an FTI Performance Diesel BA Series torque converter. Order the model recommended for your transmission application.
Not Yet Reviewed
$859.00
—
$959.00
Hughes Performance XTM Heavy-Duty Towing Series torque converters take away the worry of the "long grade" with the "heavy load." These converters are designed with heavy-duty use in mind, with a heavy-duty one-piece hub and a balloon plate, a heavy-duty sprag, and silicon spot-welded fins in the turbine and cover, providing strength beyond compare. The combination of their stator and specific application fin applies maximum power to your wheels, giving you more available engine power. These XTM converters run 7 qt. of fluid more per minute than your OE or stock converter. Because of the increased cooler flow, the transmission and converter will operate cooler, increasing the life of the tranny and converter.
( 27 )
$971.99
Street Rod torque converters from Hughes Performance are designed and manufactured for street rod enthusiasts needing a bit of an upgrade over their OE stock converters. These converters feature silicon brazing for strength, needle bearings for reliability, and stator modifications for more torque multiplication. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 116 )
$869.99
—
$895.99
RevMax Stage 3 billet single disc torque converters are designed for those who have lightly modified engines or for those that do not tow heavy weights. The showpiece of their converters is the patented torque converter stator sprag retainer which allows smoother clutch application for less strain on the input shaft. All Revmax Stage 3 converters are rated up to 350 horsepower or 700 ft-lbs. of torque. Give your ride the powertrain it deserves with an assist from the RevMax Stage 3 billet single disc torque converter best suited for your application. More product features, items, and specifications include: * CNC-machined billet one-piece front cover * Raybestos or Alto high-performance lockup friction * Proprietary input shaft seal * Billet bearing cap * Dual Torrington bearing stator design * 4140 flanged impeller hub * 4140 hardened turbine hub * Furnace-brazed impeller * TIG-welded brazed turbine * Computerized robotic welding * Precision internal clearances set to increase efficiency and improve performance * Fully pressurized and leak tested * TCRS machine computerized high-speed balancing to less than 5 grams * Runout tolerances of less than 0.005 in.
Not Yet Reviewed
$995.00
Hughes Performance Fuel Miser torque converters reduce the slippage in your transmission by 25 percent. The result is better fuel economy, more efficient shifts, and cooler transmission temperatures. They are designed to work with engines over 400 c.i.d. as well as with diesel applications. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 19 )
$891.99
If your diesel pickup truck has major power, or you consistently tow heavy loads, FTI Performance Diesel BA-3 Series torque converters are for you. With three disks, CNC-ported stators, and 4340 turbine splines, strength and performance are built in. Their billet front covers, furnace-brazed and TIG-welded fins, and heavy-duty sprag modifications combine for impressive units. FTI has tested these converters under extreme conditions, ensuring they'll stand up to your towing, driving, and performance racing needs. BA Series converters provide more torque multiplication, lower transmission temperatures, improved acceleration—and, when you can keep your right foot under control, better fuel mileage! Whether you drive a Cummins, Powerstroke, or Duramax, FTI Performance Diesel BA-3 Series torque converters put the power to the ground.
Not Yet Reviewed
$849.00
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
