Availability
Showing In Stock Items. Show All 316 Items.
EMAX vertical solo-mounted alternating silent expandable airlink systems meet high-demands with "whisper-quiet" performance. These systems are equipped with an advantageous alternating switch that will allow the units to alternate from one pump to another. The units will pump up to set pressure, then under the next start-up sequence the opposing pump will start, eliminating excessive running and allowing the pumps to cool under heavy loads. Plus, if one pump will not maintain set pressure and is not keeping up with demand, then both units will come on and run until the unit hits the pressure setting, after which it will go back into normal alternating mode. EMAX alternating silent air compressors have many features that make them easy to use, from automatic tank drains to belt tensioners. With EMAX's patented Whisper100 silent air onboard, these low-profile systems add four levels of air filtration along with making the compressor quiet, lowering the decibels by more than 35 percent. Key features: * Alternating switch that will allow the units to alternate from one pump to another * Two low-rpm solid cast iron patented pressure lubricated pumps * Two industrial grade 1750 rpm TEFC motors * Two magnetic starters with relay switch * Two ASME certified vertical tanks * Whisper100 Silent Air system * Re-usable oil filter * Oil pressure gauge
Not Yet Reviewed
$11,340.94
—
$11,446.94
BendPak MDS-6LPF mid-rise open-center flush-mount lifts are designed for full-service shops and quick-lube centers. They will collapse perfectly parallel with your flooring for those full-service bays. Additional facts and specs: * 6,000 lb. lifting capacity * Four solid steel-scissor frame support bars, making it one of the strongest mid-rise lifts in its class * Dual master hydraulic cylinder combines with dual equalizing cylinders to provide a safe and level 6,000 lb. capacity * Push-button safety lock release system * Hinge point features Zerk grease fitting to allow lubrication at critical wear areas * Comes standard with four durable cushioned-rubber contact blocks, permitting fast vehicle setup * Three locking positions allow technicians to operate at a different working heights to increase productivity
Not Yet Reviewed
$7,695.00
Bowler Performance GM LS TKX 5-speed transmission packages are designed, tested, and built for the aftermarket. The TKX offers 600 lb.-ft. of torque capacity and is capable of engine speeds of 8,000 rpms with shifts at 7,500 rpms. It is designed for multiple applications with three shifter locations, and a compact, end-loaded design that provides clearance in most transmission tunnels without floor modifications. Choose the TKX model with the gear ratios you prefer. Packages include: * GM TKX 5-speed transmission * Cast aluminum bellhousing and required hardware * Tilton 6000 Series throwout bearing with -4AN inlet and remote bleeder * RAM single disc clutch kit with spring hub discs, billet steel flywheel, and all required hardware good for up to 550 hp * Reverse light and electronic speedometer pigtail connectors * Energy Suspension transmission mount * 3 qts. of Royal Purple Synchromax fluid * Roller pilot bearing * 12-month warranty
Not Yet Reviewed
$5,689.99
On Sale
Our Summit Racing™ 1972-93 Dodge truck Mopar EFI engine swap Pro Packs deliver engineered swap systems that eliminate the guesswork and doubt, while saving you the time trying to match up universal parts. We've brought together Hooker, Lakewood, and BluePrint engines, creating a package of power and performance for your truck. Each Pro Pack contains Hooker BlackHeart engine mount brackets, transmission crossmember, polyurethane transmission mounts, and 304 stainless steel Gen III Hemi swap mid-length headers, along with Lakewood engine mounts. A BluePrint Chrysler Hemi-compatible 426 c.i.d. ProSeries fuel-injected engine, base dressed or deluxe dressed, completes the package. Select the Summit™ engine swap Pro Pack desired for your Dodge truck. Notes: * Base dressed ProSeries engine includes water pump * Deluxe dressed ProSeries engine includes spark plugs and front accessory drive with water pump, alternator, power steering pump, and A/C compressor available with black or polished pulleys Engine specs: * 610 hp/525 lb.-ft. torque * Compression ratio: 10.48:1 Block: * New "BGE" Hellcat engine block * 4-bolt main * 4.090 in. bore * One-piece rear main seal Rotating Assembly: * Forged steel crank * 4.050 in. stroke * 6.125 in. connecting rods * Forged pistons * Internally balanced front and rear Cylinder Heads: * Gen III Hemi Apache aluminum cylinder heads * 73cc chamber * 2.140 in. intake/1.650 in. exhaust valves Camshaft specs: * Hydraulic roller cam * .610 intake/.611 exhaust lift * .614 intake/.614 exhaust lift (base dressed) * 231 intake/255 exhaust duration at .050 in. * 113-degree LSA * 115-degree LSA (base dressed) Ignition timing: Controlled by ECU Also included with engine: * Fuel injection * Throttle body * Fabricated intake manifold * Harmonic balancer * Muscle car-style mid-sump swap oil pan * Coil(s) * Timing cover (Car) * Valve covers * Holley Terminator ECU controller kit and wiring harness
Not Yet Reviewed
$17,504.09
$17,481.07
On Sale
Our Summit Racing™ 1970-74 Challenger and Barracuda Mopar EFI engine swap Pro Packs deliver engineered swap systems that eliminate the guesswork and doubt, while saving you the time you would have spent trying to match up universal parts. We've brought together Hooker, Lakewood, and BluePrint engines, creating a package of power and performance for your vehicle. Each Pro Pack contains Hooker BlackHeart engine mount brackets, transmission crossmember, polyurethane transmission mounts, and 304 stainless steel Gen III Hemi swap headers, along with Lakewood engine mounts. A Chrysler Hemi-compatible 426 c.i.d. ProSeries fuel-injected engine, base dressed or deluxe dressed, completes the package. Select the Summit™ engine swap Pro Pack desired for your Challenger or Barracuda. Notes: * Base dressed ProSeries engine includes water pump * Deluxe dressed ProSeries engine includes spark plugs and front accessory drive with water pump, alternator, power steering pump, and A/C compressor with either black or polished pulleys Engine specs: * 610 hp/525 lb.-ft. torque * Compression ratio: 10.48:1 Block: * New "BGE" Hellcat engine block * 4-bolt main * 4.090 in. bore * One-piece rear main seal Rotating Assembly: * Forged steel crank * 4.050 in. stroke * 6.125 in. connecting rods * Forged pistons * Internally balanced front and rear Cylinder Heads: * Gen III Hemi Apache aluminum cylinder heads * 73cc chamber * 2.140 in. intake/1.650 in. exhaust valves Cam specs: * Hydraulic roller cam * .610 intake/.611 exhaust lift * .614 intake/.614 exhaust lift (base dressed) * 231 intake/255 exhaust duration at .050 in. * 113-degree LSA * 115-degree LSA (base dressed) Ignition timing: Controlled by ECU Also included with engine: * Fuel injection * Throttle body * Fabricated intake manifold * Harmonic balancer * Muscle car-style mid-sump swap oil pan * Coil(s) * Timing cover (Car) * Valve covers * Holley Terminator ECU controller kit and wiring harness
Not Yet Reviewed
$17,755.24
$17,689.42
On Sale
Our Summit Racing™ 1966-72 Mopar B-Body EFI engine swap Pro Packs deliver engineered swap systems that eliminate the guesswork and doubt, while saving you the time you would have spent trying to match up universal parts. We've brought together Hooker, Lakewood, and BluePrint engines, creating a package of power and performance for your vehicle. Each Pro Pack contains Hooker BlackHeart engine mount brackets, transmission crossmember, and polyurethane transmission mounts, along with Lakewood engine mounts. A Chrysler Hemi-compatible 426 c.i.d. ProSeries fuel-injected engine, base dressed or deluxe dressed, completes the package. Select the Summit™ engine swap Pro Pack desired for your Mopar B-Body. Notes: * Base dressed ProSeries engine includes water pump * Deluxe dressed ProSeries engine includes spark plugs and front accessory drive with water pump, alternator, power steering pump, and A/C compressor with either black or polished pulleys Engine specs: * 610 hp/525 lb.-ft. torque * Compression ratio: 10.48:1 Block: * New "BGE" Hellcat engine block * 4-bolt main * 4.090 in. bore * One-piece rear main seal Rotating Assembly: * Forged steel crank * 4.050 in. stroke * 6.125 in. connecting rods * Forged pistons * Internally balanced front and rear Cylinder Heads: * Gen III Hemi Apache aluminum cylinder heads * 73cc chamber * 2.140 in. intake/1.650 in. exhaust valves Cam specs: * Hydraulic roller cam * .610 intake/.611 exhaust lift * .614 intake/.614 exhaust lift (base dressed) * 231 intake/255 exhaust duration at .050 in. * 113-degree LSA * 115-degree LSA (base dressed) Ignition timing: Controlled by ECU Also included with engine: * Fuel injection * Throttle body * Fabricated intake manifold * Harmonic balancer * Muscle car-style mid-sump swap oil pan * Coil(s) * Timing cover (Car) * Valve covers * Holley Terminator ECU controller kit and wiring harness
Not Yet Reviewed
$17,417.29
$17,367.67
Ford Performance Parts 2018 2.3L 310 hp EcoBoost long block crate engines are designed for traditional rear drive installations. They're the same EcoBoost engine found in the 2018 Mustang and feature turbocharging, direct injection, and twin independent variable cam timing (Ti-VCT). The swap possibilities are almost endless: from early street rods, kit cars, most generations of Mustang, to just about any other vehicle build. Ford Performance Parts 2.3L 310 hp Mustang EcoBoost engine kit—this kind of performance comes standard with a dose of adrenaline! Features and items: * 310 hp and 350 lbs.-ft. torque at 3,000 rpm (with 93 octane fuel) * Production turbocharger * Starter and mounting hardware * Alternator and mounting hardware * Flywheel * Engine harness (not installed, must be used with Ford Performance control pack) * Throttle body (not installed, must be used with Ford Performance control pack) * Engine kit uses Ford Performance Parts M-6017-23T control pack (not included) for easy plug-and-play installation
( 1 )
$5,242.99
Ford Performance Parts 5.0L Coyote Gen 4X crate engines are modern 5.0L 32-valve DOHC V8s that utilize advanced features, such as direct and port fuel injection, twin independent variable camshaft timing (Ti-VCT), high-flow aluminum cylinder heads, and 12:1 compression to deliver 460 hp and 420 lb.-ft. of torque (with premium fuel). The all-aluminum cylinder block features plasma transferred arc spray-in liners, cross-bolted main bearing caps, and thick main bearing bulkheads for strength. Ford's Gen 4X 5.0L Coyote features a single 80mm throttle body for easier packaging in various applications. Features and specs: * Hypereutectic aluminum pistons * Sintered steel connecting rods as used on the Boss 302 Mustang * Forged steel crankshaft * Single 80mm "drive-by-wire" throttle body * 9.5 qt. steel oil pan * Composite lightweight intake manifold * Mustang GT 409 stainless steel exhaust manifold—right side only * Engine mount bosses and bellhousing mount pattern common to 5.0L modular engines * 10R80 flexplate included * Engine weight: 445 lbs. without front accessory drive components Note: Driver side exhaust flange utilizes 5.2L pattern
Not Yet Reviewed
$11,704.99
Chevrolet Performance LSX 454 long block crate engines are built with an all-forged, super-tough rotating assembly and feature a pair of new deep-breathing LSX 6-bolt cylinder heads. They also come dressed with great looking, all-new orange powdercoated valve covers with an engraved LSX 454 logo. With a carburetor and high-flow Chevrolet Performance intake manifold (sold separately), these engines are good for about 627 hp and 586 lbs.-ft. of torque. Due to the number of application variations, the LSX 454 crate engines do not include an oil pan, and the valve covers do not include provisions for mounting the ignition coil brackets. Other specifications include: * 4.185 in. bore * 4.125 in. stroke * Cast iron LSX Series block with cross-bolted 6-bolt main caps * Forged steel crankshaft * Forged steel connecting rods * Forged aluminum 11.0:1 compression pistons * Hydraulic roller camshaft * 0.635 in. lift intake/0.635 in. lift exhaust, 236 intake/246 exhaust duration at .050 in. lift * Aluminum LSX-LS7 cylinder heads with 70cc chambers * 1.8:1 aluminum roller rocker arms * 58-tooth reluctor wheel
( 1 )
$16,836.20
RideTech Corvette coilover suspension systems include MuscleBar sway bars, Delrin control arm bushings, and powdercoated conversion brackets. The 100 percent bolt-on kit will significantly improve your Corvette's handling, while giving you control over ride-height adjustment. RideTech engineers custom-tailored the system's HQ Series shock absorber valving for modern, world-class ride quality. Rebound adjustment knobs help you fine-tune ride and handling to your driving style and tire selection. For the ultimate track experience, upgrade to the TQ Series coilovers with a remote reservoir for high and low speed compression adjustments. RideTech's CNC-bent MuscleBar sway bars increase bar rate over stock, allowing for more comfortable, compliant coil spring rates. MuscleBars feature investment cast bar ends that perfectly engage end-link bushings as your Corvette's cornering loads change. Delrin-lined mounting bushings never squeak or need lubricating. The same is true for the kit's Delrin A-arm bushings. Overall, the C4 Corvette coilover conversion systems offer tremendous bang for the buck with real-world improvements. They're a game changer for the C4 Corvette platform. (Included shock absorbers carry a 1,000,001 mile warranty.)
Not Yet Reviewed
$7,770.00
RideTech 1967-69 Camaro/Firebird complete coilover suspension systems include everything you need to completely upgrade your existing suspension. The package contains front upper and lower StrongArm control arms, tall spindles, front MuscleBar, a rear bolt-on 4-link, and four HQ Series coilover shocks for every corner of your vehicle. The benefit of buying a complete suspension system is that it takes all the guesswork out of what are the best parts to purchase. RideTech has spent hours collecting data to find a perfect spring rate and components for your vehicle's performance and ride quality. RideTech complete coilover systems include: * RideTech tall spindles will induce more negative camber gain to maximize tire contact patch during cornering. It also offers a 2 in. pin drop which allows for the use of longer shocks creating more suspension travel. * Upper StrongArms feature corrected ball joint angles for the tall spindles. The upper ball joints have been moved back to allow for additional caster setting to improve high speed stability and steering feel. Offset slugs are also available for additional caster. Injection molded Delrin bushings with 13 percent PTFE are used to reduce deflection and stiction. * Lower StrongArms feature a double sheer lower mount for increased strength. The lower shock mount is dropped to increase suspension travel and moved the lower ball joint forward to increase caster settings while keeping the wheel centered in the wheel opening. Injection molded Delrin bushings with 13 percent PTFE are used to reduce deflection and stiction. * HQ Series coilover shocks utilize an impact forged aluminum body and monotube design to deliver excellent ride quality and handling. The rebound knob is located at the top of the shock for underhood access. * Front MuscleBar helps to reduce body roll and creates room for wider front tires. It includes the PosiLink end links that provide immediate engagement between the chassis and control arms. * Bolt-on 4-Link greatly improves traction, handling, and ride quality. Installation does not require the any major modifications to the floor pan and requires only minimal welding to the axle tube. Works with mini tubs. The R-joint rod ends combine the best qualities of low friction movement, lateral stability, full range articulation, and quiet operation into one special bearing that is as home on the street as it is on the racetrack.
Not Yet Reviewed
$5,975.00
RideTech 1955-57 Chevrolet coilover suspension systems transform the ride, handling, and looks of your Tri-5. The benefits of buying these complete kits is that RideTech has done all the homework for you. They have matched the perfect spring rate and components for your Chevy's best performance and ride quality. All you do is install. Completely upgrade your existing suspension with RideTech coilover suspension systems. Features include: * Upper StrongArms are powdercoated black and fully assembled with ball joints, bushing, and cross shafts. They feature corrected ball joint angles and the upper ball joint have been moved back to allow for additional caster setting to improve high speed stability and steering feel. * Lower StrongArms feature a double sheer lower mount for increased strength. They also are powdercoated black and fully assembled with ball joints, bushing, and cross shafts. * HQ Series coilovers utilize an impact forged aluminum body and monotube design to deliver excellent ride quality and handling. They allow fine-tuning of the ride quality and handling. The rebound knob is located at the top of the shock for underhood access. * Front MuscleBar helps reduce body roll and includes the PosiLink endlinks that provide immediate engagement between the chassis and control arms. * Bolt-on 4-link greatly improves traction, handling, and ride quality.
Not Yet Reviewed
$5,400.00
Manufacturer Rebate
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L80E Level 4 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 800 hp * Up to 700 lb.-ft. of torque * Stall: 2,800 to 3,400 * Custom-built, custom-stalled 10 in. billet racing lock-up converter * Master overhaul kit with Alto hardened steels * Raybestos Stage 1 frictions * TransGo reprogramming kit * Filter * Torrington bearing kit * Bushing kit * Thrust washer kit * Internal wiring harness * New manifold pressure switch * New EPC solenoid * New PWM solenoid * New input and output speed sensors * New 1-2 and 3-4 shift solenoids * Expanded capacity forward clutch drum * Extra-capacity 2nd gear clutch assembly * Expanded capacity 3rd clutch drum * Heat-treated input shaft * 300M main shaft * 300M forward clutch hub * Updated molded steel direct clutch piston * Updated reverse band * New low roller assembly * Wide kickdown band with new apply piston * Heavy-duty intermediate sprag * Updated boost valve * Updated TCC regulator valve * Blueprinted pump and valve body * Transmission mount * New OEM steel pan
( 1 )
$7,845.00
Manufacturer Rebate
GearStar GM high performance transmissions are built to the horsepower, torque, and rear gear ratio specs of the engine that it will be matched to. Unlike other high performance transmissions builders, GearStar individual transmissions are hand-built by one technician from start to finish. Before a transmission and torque converter leaves their facility, they are dyno tested for the equivalent of 100 miles, ensuring proper working condition. GearStar GM 4L65E Level 4 transmissions with torque converter are built with the highest quality parts available. "Heart-pounding performance with industry leading experience"; select the proper transmission for your build and "strap yourself in to experience uncompromising performance" with the "legendary road-proven craftsmanship" of GearStar Performance transmissions. Features and specs: * 650 hp * Up to 600 lb.-ft. of torque * Stall: 2,600 to 4,000 * Custom-built and custom-stalled 10 in. or 11 in. billet racing lock-up converter * Master overhaul kit with Alto hardened steels * Raybestos Gen II racing frictions * Filter * 29-element dual cage sprag * High-capacity upgraded pump assembly * New hardened pump rings * New 13-vane pump rotor * New vanes * New stator * .500 boost valve * Pressure regulator valve * Updated boost valve * TransGo reprogramming shift kit with Shift Command * Complete Torrington bearing kit * Bushing kit * Thrust washers * Heavy-duty hardened sun shell * Heavy-duty expanded capacity input drum with reinforcing sleeve * High-rev spring kit * 5-pinion heavy-duty front and rear planetary gear sets with sun gear * Hardened output shaft * Hardened reaction shaft and hub * Super hold 4th servo * Corvette servo * Wide carbon fiber wide 2-4 band * New internal wiring harness with new TCC solenoid * New shift solenoids * New EPC solenoid * New PWM solenoid * New 3/2 solenoid * New manifold pressure switch * New electronic speed sensor * New valve body spacer plate * New OE steel transmission pan * Transmission mount
( 2 )
$5,945.00
The Ridetech complete coilover suspension system for the 1964-66 Ford Mustang includes everything you need to give your vintage muscle car modern drivability. The package contains front upper and lower control arms, tall spindles, steering arms, inner and outer tie rods, front MuscleBar, a bolt-In 4=link system, and four HQ Series coilovers for every corner of your vehicle. The benefit of buying a complete suspension system is that it removes all the guesswork when purchasing a new suspension. Ridetech has spent hours collecting data to find a perfect spring rate and components for your vehicle's performance and ride quality—designed to lower your vehicle. * Upper StrongArms feature corrected ball joint angles for the tall spindles. The upper ball joint have been moved back to allow for additional caster setting to improve high-speed stability and steering feel. Billet cross-shafts are included that feature a lowered mounting point to increase camber gain and correct suspension geometry. They house a stout double sheer lower shock mount. * Lower StrongArms feature a unique design that combines the control arm and strut rod into a stronger, more appealing one-piece design. Additional caster is designed into the arms and includes a robust bearing in an aluminum housing at the front mount to replace the soft factory rubber units. * TruTurn System includes tall spindles which induce more negative camber gain to maximize tire contact patch during cornering. It also includes steering arms, center link adapter, tie rods and adjusters to virtually eliminate bump steer, correct Ackerman angle, and allow for wider tires. Includes heavy-duty frame rail brace. This spindle is designed for use with 1967-69 Camaro brake systems. Compatible with OEM manual steering AND with the Borgeson power steering conversion box. * Optional "Hub" spindles offer the same geometry improvements as the pin spindles, but add the performance and simplicity of late model Mustang hubs and brakes. Includes S550 2015-23 Mustang hubs for maximum strength, consistent braking and reduced maintenance. Compatible with 2015-23 Mustang brake systems, OE and aftermarket (caliper brackets included). Minimum 17 in. wheels. Hubs fit Ford car 5 x 4.5 in. lug pattern and include 14mm studs. * HQ Series coilovers utilize an impact forged aluminum body and monotube design to deliver excellent ride quality and handling. They allow fine-tuning of the ride quality and handling; the rebound knob is located at the top of the shock for underhood access. The shocks come standard with a 1,000,0001 Mile Warranty. Interested in Autocross or Road Course racing? Consider the TQ Series coilovers. * Front MucleBar sway bar helps reduce body roll and includes the PosiLink end links that provide immediate engagement between the chassis and control arms. Includes billet aluminum frame straps (anodized black) and low-friction bushings. * Bolt-on 4-link dramatically improves traction, handling, and ride quality. Installation does not require significant modifications to the floor pan and requires only minimal welding to the axle tube. Works with mini-tubs. All links are double adjustable with R-Joint rod ends, which combine the best qualities of low friction movement, lateral stability, full range articulation, and quiet operation into one special bearing that is at home on the street as it is on the race track! * Weld-on lower axle brackets are available if using an aftermarket axle housing without stock-style leaf spring pads. (Part number 70010122, sold separately.)
Not Yet Reviewed
$7,670.00
EMAX Industrial Plus Silent Air piston compressors are quiet. The most common complaints about compressors are their high noise levels. EMAX Silent Air units not only still the noise, but they also do it with a big cfm output and lower rpm. Featuring their Whisper 100 system installed on the back of the tanks, stationary compressor dB ratings are reduced by as much as 25 percent. The Whisper dissipates compressor intake noise by channeling intake air through a series of baffle plates and prefilter media inside the silencer cabinet. Piston intake noise is trapped and dissipated within the silencer structure; plus, it also provides secondary filtration for cleaner air. Industrial Plus Silent Air piston compressors are designed for up to 50,000 hours of commercial or industrial use with proper maintenance. At the core of these extremely durable compressors are super-quiet pumps featuring cast iron crankcases, precision-balanced cast iron crankshafts, and high-quality stainless steel roller bearings to ensure smooth, efficient operation. For long life and rebuildability, EMAX adds steel connecting rods with replaceable rod bearing inserts, removable cast iron cylinders and cylinder heads, disc intake and exhaust valves, and cast iron flywheels with a built-in fan. These bigger low-rpm pumps have a larger bore and stroke, so you get big cfm output with reduced friction and heat buildup. All EMAX Industrial Plus compressors have low-rpm motors (1,750 rpm). Because of their higher torque factor, compared to the 3,450 rpm motors most manufacturers use, they run much cooler. They also yield low harmonic distortion, provide much higher torque in cold weather starting, and require less electricity to start. Other features include big 1 3/8 in. output shafts, large starting and running capacitors, and dynamically balanced armatures. Their 15 Service Factor means the motors can be pulled 15 percent over full load. Depending on the application, many Silent Air piston compressors feature totally enclosed, fan-cooled (TEFC) motors that keep harmful dust and particulates out of the motor. This allows them to be used in dusty commercial and industrial environments without worrying about maintenance. They have 100 percent copper windings with pre-wired magnetic starters (necessary on any motor over 15 amps). These are high-quality, name brand, premium efficiency motors that meet all UL and CSA requirements. Some lower horsepower models are equipped with name brand, open-drip (OPD) motors. The running and starting windings on these motors are all 100 percent copper-wound for premium efficiency, reliable performance, and durability. These units also meet all UL and CSA requirements and include pre-wired Condor combination starter and pressure switches with actuation-type diaphragms. EMAX Industrial Plus Silent Air piston compressors also feature: * Head unloaders allow for load-less starting and can help cool the pump in high-duty cycle applications * Built-in inter-coolers and after-coolers * Raised-pump mounting platforms that open the underside of the crankcase to cooling air flow * Automatic belt tensioners for much easier and quicker adjustments and alignment * Selectable continuous-run or automatic start/stop operation to maximize performance and reduce wear * OSHA-approved belt guards for your safety * ASME code-compliant tanks * Dual-timer automatic tank drains eliminate maintenance * Taper lock 2-groove pulleys * Dual 2-groove belts for long life and low vibration * Extended tank water drain pipes plumbed to the front with 1/4 in. ball valve handles * 100 percent brass check valves, safety valves, and ball valves * Top-quality plumbing fittings
( 16 )
$5,296.82
—
$7,204.82
Detroit Speed Chevy II subframes are bolt-in replacements for the original stock subframe. They improve the handling and ride quality by utilizing Detroit Speed's unique suspension geometry. These are the ONLY Chevy II frames in the aftermarket industry with OEM-quality stamped crossmembers for improved structural rigidity. The bay bars feature rigid integral hood hinge mounting and are hidden when used with Detroit Speed's Chevy II Inner Fenders package. Order the Chevy II front frame model with the coilover options preferred for your application. Subframe suspension kits include the following components: * Tubular upper and lower control arms * Aluminum body coilover shocks * Torrington bearings * Coilover springs * Power rack and pinion steering * Integrated splined sway bar * Control arm cross shafts with caster tuner bushings • Forged Detroit Speed spindle • Composite sway bar bushings • Spanner tool for easy shock adjustments
Not Yet Reviewed
$10,295.95
RideTech C1500 complete coilover systems include everything needed to create modern drivability with an aggressive stance for the 1988-98 Chevrolet and GMC C1500 trucks. The package contains front upper and lower StrongArm tubular A-arms, front and rear HQ Series coilover shocks, front sway bar, HD drop spindles, and rear wishbone with integrated C-notches. The benefit of a RideTech complete suspension system is that it removes all the guesswork as to which components to purchase—saving you time and money. Overview of features, specs, and parts: * Ride height is approximately 4 in. lower than stock in the front and 6 in. in the rear (coilovers add adjustability for rebound and ride height) * Front coilover setup includes HQ Series shocks and bolt-on upper shock mounts to allow more ground clearance and maximum suspension travel * HQ Series aluminum body shocks are a monotube design, rebound adjustable, and come with a 1,000,001 mile manufacturer warranty * Upper StrongArm A-arms feature corrected ball joint angles for the lowered ride height, and the length has been altered to create more camber adjustment. Injection-molded Delrin bushings with 13 percent PTFE are used to reduce deflection and stiction. Also includes integrated brake line mounting brackets. * Lower StrongArm A-arms feature a double-sheer lower shock mount for increased strength; the injection-molded Delrin bushings with 13 percent PTFE are used to reduce deflection and stiction. Also included are quality ball joints for a completely bolt-on experience. * Front MuscleBar sway bar is included to reduce body roll and includes the Delrin liners to minimize suspension bind * HD drop spindles are used to all the use of a longer stroke shock and improve suspension geometry and bump steer * Bolt-on wishbone system greatly improves traction, handling, and ride quality. Installation does not require welding or major modifications to the bed floor. -- Includes patent-pending R-joint rod ends to eliminate binding and noise -- Wishbone upper link (rather than panhard bar) for zero lateral movement during suspension travel allows extremely tight wheel/tire fitment -- Optimized anti-squat, instant center and pinion angle migration for dramatic improvements in handling and traction -- Bolt-on C-notch reinforces OEM frame rails and features integrated suspension mounts -- Simple installation with minimal OEM rivet removal
Not Yet Reviewed
$6,880.00
RideTech 1965-66 GM B-body coilover suspension systems include everything needed to provide a lowered stance with dramatically improved handling and ride quality. Engineered by RideTech and wound by Hyperco, the rear coil springs offer the perfect lowered stance. Hyperco springs are CNC cold-wound and machined from high-tensile chrome silicon steel—the highest grade spring material available. Enjoy RideTech's passionate commitment to finding the perfect spring rate and components for your vehicle in their 1965-66 Chevrolet coilover suspension kits. Features, items, and specs: * For cars with two rear upper control arms, an additional StrongArm is required * Black powdercoated upper StrongArms feature corrected ball joint angles, and are fully assembled with ball joints, bushing, and cross shafts * Upper ball joints moved back to allow for additional caster setting (improves high speed stability and steering feel) * Black powdercoated lower StrongArms feature a double-sheer lower mount for increased strength, and are fully assembled with ball joints, bushing, and cross shafts * Both front coilovers and rear shocks utilize an impact-forged aluminum body and monotube design to allow fine-tuning—and deliver excellent ride quality and handling with a 1,000,0001 mile warranty (rebound knob located on top of front shocks for underhood access) * Hyperco springs provide a consistent spring rate that will last a lifetime * Front and rear MuscleBars help reduce body roll and include PosiLink endlinks that provide immediate engagement between chassis and control arms * Rear StrongArms provide added strength to help get the power to the pavement * Upper arm and panhard bar utilize R-joint technology to provide smooth operation and reduce roll bind
Not Yet Reviewed
$5,330.00
RideTech 1964-67 GM A-body coilover suspension systems are specifically designed for the 1964-67 GM A-body platform. The package contains front upper and lower control arms, tall spindles, front and rear MuscleBars, rear StrongArms, and four HQ Series coilovers. RideTech 1964-67 GM A-body coilover suspension kits include everything needed to create modern drivability from vintage muscle. Features, parts, and specs: * Tall spindles will induce more negative camber gain to maximize tire contact patch during cornering (they also offer a 2 in. pin drop which allows for longer shocks creating more suspension travel) * Upper StrongArms feature corrected ball joint angles for the tall spindles * Upper ball joints have been moved back to allow for additional caster setting (improves high speed stability and steering feel; offset slugs available for additional caster) * Injection-molded Delrin bushings with 13 percent PTFE used to reduce deflection and stiction * Lower StrongArms feature a double-sheer lower mount for increased strength * Dropped lower shock mount to increase suspension travel * Lower ball joint moved forward to increase caster settings, while keeping the wheel centered in the wheel opening * HQ Series Shockwaves allow fine-tuning and deliver excellent ride quality and handling with a 1,000,0001 mile warranty (rebound knob located on top of shock for underhood access) * Brackets included with rear coilovers for easy attachment to the frame and the 10/12 bolt rear-end or Currie 9 in. (brackets for a Moser rear-end also available) * Front MuscleBar helps reduce body roll and creates room for wider front tires (includes PosiLink endlinks that provide immediate engagement between chassis and control arms) * Rear StrongArms provide added strength to help get the power to the pavement; they utilize R-joint technology to combine the best qualities of low-friction movement, lateral stability, full range articulation, and quiet operation into one special bearing
Not Yet Reviewed
$5,645.00
OTC 55-ton heavy-duty shop presses feature side-to-side positioning of ram to allow full capacity pressing along entire bolster length without buckling or bending. Presses include a single-acting ram with 13 in. stroke, electric/hydraulic pump, gauge, 3/8 in. I.D. x 8 ft. hose, and pump mounting bracket.
Not Yet Reviewed
$10,749.99
RideTech 1967-70 Cougar coilover suspension systems include everything you need to give your vintage Cougar modern drivability. These packages contain front upper and lower control arms, tall spindles, steering arms, inner and outer tie rods, a front MuscleBar, a bolt-in 4-link system, and four HQ Series coilovers for every corner of your vehicle. The bolt-on 4-link vastly improves traction, handling, and ride quality. Installation doesn't require any major modifications to the floor pan and requires only minimal welding to the axle tube (works with mini tubs). The R-joint rod ends combine the best qualities of low friction movement, lateral stability, full range articulation, and quiet operation into one special bearing. RideTech 1967-70 Cougar coilover suspension systems are as comfortable on the street as they are on the racetrack! Features, items, and specs: * Upper StrongArms feature corrected ball joint angles for the tall spindles * Upper ball joint moved back to allow for additional caster setting (improves high-speed stability and steering feel) * Billet cross shafts feature a lowered mounting point to increase camber gain and correct suspension geometry (they house a stout double-sheer lower shock mount) * Lower StrongArms feature a unique design that combines the control and strut rod into a stronger, more appealing one-piece design * Additional caster designed into the arms * Robust bearing in an aluminum housing at the front mount to replace the soft factory rubber units * HQ Series coilovers allow fine-tuning and deliver excellent ride quality and handling with a 1,000,0001 mile warranty (rebound knob located on top of front coilovers for underhood access) * Front MuscleBar helps reduce body roll and includes PosiLink endlinks that provide immediate engagement between chassis and control arms
Not Yet Reviewed
$6,130.00
RideTech subframes deliver several key improvements over the original and some existing aftermarket subframes. Optimized suspension geometry, improved wheel and tire clearance, and rack and pinion steering technology, plus many more features will surely put RideTech's subframes on the top of your builder's wish list. Select the kit with the preferred spindles. Features and benefits: * Optimized geometry provides improved roll center, Ackermann, camber gain, caster and bump steer * Lowers stance 1 to 3 in. and maintains factory track width while increasing wheel and tire clearance * 2 in. more tire clearance per side over stock subframe allows better turning radius with larger tires/wheels * Fits up to 6.5 in. BS with no modifications or reduction in turning radius * Rack and pinion steering upgrade provides improved steering feel, enhancing driver feedback * Modular design is compatible with coilovers or ShockWaves (sold separately) * Subframe features durable powdercoat finish for great, long-lasting good looks and corrosion resistance * Available with AFX pin or late model hub spindle design -- Hub spindle allows install of modern C5/C6 Corvette brakes and C5/C6/C7 hubs (hubs not included) -- Pin spindle is compatible with stock style brakes (including aftermarket kits that fit stock spindle) * One-piece billet 6061 T-6 aluminum upper control arms and steering arms add superior strength * Larger front sway bar controls body roll, improving weight transfer * Tubular lower control arms include eccentric adjustment for caster and camber adjustments * Alignment adjustments are made complete under the car --no adjustments inside engine bay * Multiple motor mount options * Included adjustable transmission crossmember compatible with most popular manual and automatic transmissions * Improved header clearance and exhaust routing allow for a variety exhaust solutions
Not Yet Reviewed
$6,495.00
—
$6,645.00
BendPak HD-9ST narrow width car lifts are rugged, space-saver solutions with a 9,000 lb. lifting capacity. They are great for the DIY projects and daily shop work at small businesses. These BendPak lifts are designed for shops or garages where space is a premium. Trust in BendPak for all of your lifting needs. Additional features include the following: * Electric/hydraulic power system * Single hydraulic cylinder mounted underneath runway * Fully enclosed lifting cables, safety locks, and sheaves * Internal anti-sway slider blocks in each column * Oversized self-lubricating cable rollers * Heavy-duty 3/8 in. aircraft cable * Rugged 1 1/4 in. roller axles * Multi-position safety locks in each column * Adjustable lock ladders * Runways feature non-skid surface * Push button pneumatic safety release * Independent backup slack cable safety latches * Removable approach ramps for additional drive under clearance * Longer approach ramps for additional drive under clearance
( 7 )
$5,995.00
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
