Availability
Showing In Stock Items. Show All 135 Items.
TCI Maximizer high-torque towing converters are efficient units that put more of your engine's torque to the ground. Slippage is minimized, providing better gas mileage and as much as a 20-degree F reduction in transmission temperature. Another benefit is reduced engine rpm at highway speed. These torque converters are available in a variety of size options for more than a dozen Chevy, Ford, and Mopar transmission models.
( 20 )
$855.95
Street Master torque converters are designed for the driver who is looking for a competitive advantage. By raising the stall rpm, these converters will completely eliminate slow, sluggish starts. Recommended for stock to slightly modified engines for maximum performance, they'll allow the engine to idle smoothly when the car is in gear. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 r.p.m. lower.
( 235 )
$852.99
—
$964.99
These Maximizer Street Performance torque converters are built with extra reinforcement and thicker mounting surfaces to withstand the additional load and vibration put through the drivetrain by a truck with performance modifications. By providing additional stall, your truck will see better initial takeoff and will not lug the engine when using big tires. Special attention is made to match the converters to the power range of most trucks that do double duty as off-road and daily drivers. Improved rear-wheel horsepower and elapsed times are some of the results.
( 7 )
$786.95
Tow Master series torque converters from Hughes Performance are designed to increase bottom-end pulling power in your tow vehicle without sacrificing top-end efficiency or lockup. Because they offer your vehicle more power with less effort, mileage can be increased by as much as 1-2 miles per gallon. Recommended for slightly modified engines, these Tow Master converters help you get the job done. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 25 )
$865.99
—
$891.99
On Sale
B&M Traveler torque converters are designed for use in motor homes, tow vehicles, or other heavy-duty applications where a slightly higher stall speed is helpful in getting the vehicle moving. Stronger than a stock converter, these Travelers have been internally modified to provide about 300 rpm more stall speed. This helps in initial acceleration without sacrificing normal highway operation. Pressure tested, fully balanced, and manufactured for long life, these Traveler converters will get you moving and on your way.
( 3 )
$899.95
$808.95
For all of your driving needs, you'll enjoy the strength and feel of FTI Performance Diesel BA Series torque converters. These units include billet front covers, heavy-duty sprag modifications, and furnace-brazed and TIG-welded fins. Their single disc works great for everyday driving and moderate towing. BA Series converters provide more torque multiplication, lower transmission temperatures, improved acceleration—and when you can keep your right foot under control, better fuel mileage! Give your pickup truck the power to control your ride with an FTI Performance Diesel BA Series torque converter. Order the model recommended for your transmission application.
Not Yet Reviewed
$859.00
—
$959.00
Chevrolet Performance SuperMatic torque converters are tailored for performance. Designed for their crate engines and transmissions, these torque converters are built to match the power outputs of the engines and to help ensure optimal performance of your powertrain system. Your project is different than the next guys but Chevrolet Performance SuperMatic torque converters bring together your application for durable factory-engineered performance that will have you cruising in no time! Features include: * Steel billet front cover * Custom stator * Fully furnace-brazed pump and turbine * Heavy-duty lock-up clutch * Internal components static balanced * Fully vector balanced as an assembly
( 1 )
$1,127.36
—
$1,130.05
Hughes Performance XTM Heavy-Duty Towing Series torque converters take away the worry of the "long grade" with the "heavy load." These converters are designed with heavy-duty use in mind, with a heavy-duty one-piece hub and a balloon plate, a heavy-duty sprag, and silicon spot-welded fins in the turbine and cover, providing strength beyond compare. The combination of their stator and specific application fin applies maximum power to your wheels, giving you more available engine power. These XTM converters run 7 qt. of fluid more per minute than your OE or stock converter. Because of the increased cooler flow, the transmission and converter will operate cooler, increasing the life of the tranny and converter.
( 27 )
$971.99
Street Rod torque converters from Hughes Performance are designed and manufactured for street rod enthusiasts needing a bit of an upgrade over their OE stock converters. These converters feature silicon brazing for strength, needle bearings for reliability, and stator modifications for more torque multiplication. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 116 )
$869.99
—
$895.99
RevMax Stage 3 billet single disc torque converters are designed for those who have lightly modified engines or for those that do not tow heavy weights. The showpiece of their converters is the patented torque converter stator sprag retainer which allows smoother clutch application for less strain on the input shaft. All Revmax Stage 3 converters are rated up to 350 horsepower or 700 ft-lbs. of torque. Give your ride the powertrain it deserves with an assist from the RevMax Stage 3 billet single disc torque converter best suited for your application. More product features, items, and specifications include: * CNC-machined billet one-piece front cover * Raybestos or Alto high-performance lockup friction * Proprietary input shaft seal * Billet bearing cap * Dual Torrington bearing stator design * 4140 flanged impeller hub * 4140 hardened turbine hub * Furnace-brazed impeller * TIG-welded brazed turbine * Computerized robotic welding * Precision internal clearances set to increase efficiency and improve performance * Fully pressurized and leak tested * TCRS machine computerized high-speed balancing to less than 5 grams * Runout tolerances of less than 0.005 in.
Not Yet Reviewed
$995.00
Hughes Performance Fuel Miser torque converters reduce the slippage in your transmission by 25 percent. The result is better fuel economy, more efficient shifts, and cooler transmission temperatures. They are designed to work with engines over 400 c.i.d. as well as with diesel applications. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 19 )
$891.99
If your diesel pickup truck has major power, or you consistently tow heavy loads, FTI Performance Diesel BA-3 Series torque converters are for you. With three disks, CNC-ported stators, and 4340 turbine splines, strength and performance are built in. Their billet front covers, furnace-brazed and TIG-welded fins, and heavy-duty sprag modifications combine for impressive units. FTI has tested these converters under extreme conditions, ensuring they'll stand up to your towing, driving, and performance racing needs. BA Series converters provide more torque multiplication, lower transmission temperatures, improved acceleration—and, when you can keep your right foot under control, better fuel mileage! Whether you drive a Cummins, Powerstroke, or Duramax, FTI Performance Diesel BA-3 Series torque converters put the power to the ground.
Not Yet Reviewed
$849.00
Doug's Headers has long been recognized of as one of the premiere exhaust header manufacturers in the performance industry. Since1958, they have been producing high-quality, hand-built, mandrel-bent exhaust headers. Each and every header is tuned with the proper tube size and length to efficiently remove all of the exhaust from each cylinder, reducing pumping losses, and resulting in dramatic increases in horsepower and torque. Doug's headers are carefully developed on the vehicles that they are intended to fit and are re-checked numerous times during the design and manufacturing process. Their designs include mid-length headers, Tri-Y headers, and long tube headers, plus manifold replacement headers. Their headers come with all the necessary mounting hardware, collector reducers or connector pipes, premium extra-thick gaskets, and detailed installation instruction sheets. The gaskets are rated up to 1100 degrees F, pressures to 3700 psig (255 bar), and are designed for an exact port match with their headers. Doug's Headers offer a choice of finishes: * Metallic Ceramic Thermal Barrier Coating (MCTBC), which is polished with a vibratory finishing process that not only produces a high-luster aluminum appearance, but also compresses and activates the coating, which increases the surface hardness. The finish is 60 percent more corrosion resistant than an unpolished surface, easy to maintain, and will last for years under normal operation conditions. MCTBC also protects and extends the life of headers by creating a thermal barrier that significantly lowers under hood temperatures and protects the substrate metal from thermal fatigue. * Hi-Temp black coating is an affordably priced alternative to their MCTBC. This finish provides good corrosion and heat protection when compared to many of the "cheaper" header finishes being applied by our competitors. * Raw steel is available for individual customizing Unless otherwise noted, these headers are designed to fit the vehicle as it came from the manufacturer. This includes components like cylinder heads, chassis, steering, motor mounts, body mounts and bushings, etc. If your vehicle is using aftermarket components, parts from other applications, or custom altered parts, then it is the installer's responsibility to verify fitment.
( 704 )
$750.10
—
$1,045.05
MagnaFlow Street Series performance exhaust systems deliver the smooth, deep sound you want—and the wide-open performance power you need! They feature straight-through flow designs for the ultimate in unrestricted horsepower and torque, while maintaining exhaust efficiency. These kits are an engineered balance of interior and exterior noise levels and are tested against SAE j1169 standards. Street Series components are built with 409 stainless steel and all mandrel-bent tubing. They're available in numerous configurations, including cat-back, rear axle-back, crossmember-back, and rear section; single, dual, tri, or quad turbo mufflers; and several outlet and tip options. Order the MagnaFlow Street Series performance exhaust tailored for your specific make and model. The systems carry a lifetime construction warranty.
( 608 )
$771.00
—
$1,060.00
Experience is in Doug's Headers DNA. They have been a respected name since the 1960s and remain one of today's most popular brands among muscle car enthusiasts who don't sacrifice quality and fit when it comes to their vehicle. Doug's stainless steel headers will give the greatest increases in horsepower and torque across the entire rpm spectrum, and they are meticulously designed to provide maximum power and the highest quality available. Available in many fitments, choose a set designed for your vehicle. Key features: * 304 stainless steel construction to prevent rust and corrosion * 3/8 in. thick machined flanges to prevent warping * Mandrel-bent tubes for an accurate fit and improved flow * Precision formed long transition collectors reduce backpressure * Header tubes have a natural stainless finish * Necessary mounting hardware, collector reducers or connector pipes, premium gaskets, and detailed installation instruction sheets are included
( 26 )
$797.85
—
$981.95
Stainless Works CNC mandrel-bent exhaust systems are the simply the best for improving your vehicle's performance, sound, and mileage. Made of high-grade 304 stainless steel, they offer an array of options to unleash more torque and horsepower while delivering the sound your vehicle has been lacking. Most are designed to use factory hangers. Stainless Works not only offers their Factory Connect option that mates to a factory connection point, but also Performance Connect options for many models. Performance Connect gains more performance than factory connection points allow, and they require the installation of Stainless Works headers (sold separately) to gain the full performance benefit. Stainless Works also builds their mufflers entirely of stainless steel. They will never "burn in," "blow out," or change their tone—ever. Choose from a selection of universal or application-specific muffler designs, including turbo chambered (loud), chambered round (louder—can be reversed for an even more aggressive sound), and turbo S-tube (loudest—may be too aggressive for a daily driver). Additional features of Stainless Works CNC mandrel-bent exhaust systems include: * 304 stainless will never red-rust like cheaper 409 stainless * TIG-welded for strength * Durable 3/8 in. thick flanges * Mandrel-bent (no buckling) for optimal flow * Variety of tip options (varies by application) * Truck exhausts available with three exit locations: behind the passenger tire; under the rear bumper (one on each side); and in front of the passenger tire * Install-Ready; all systems come with all necessary parts to make installation as smooth as possible
( 30 )
$785.84
—
$954.08
Smittybilt Gen2 X20 Comp Series winches have been thoroughly updated with heavy-duty features for enhanced performance. They feature 6.6 hp Amphibious Series wound motor that offers the highest torque in the industry, and are connected to a 3-stage planetary gear system for increased pulling power and line speed. The winches also come standard with a wireless remote control that can be wired directly to the winch or unplugged for trouble-free wireless operation. Smittybilt Gen2 X20 Comp Series winches feature a state-of-the-art specially-coated synthetic rope cable that will not kink, curl, or splinter--and it's resistant to UV rays and abrasions. They come with rope sleeve for the synthetic cable, an attached forged steel hook, high-grade competition billet aluminum fairlead, UV-resistant matte black textured finish, a larger clutch for easy control during gloved operations, oversized tie rod struts for maximum strength, and an inductive braking system that reduces heat for long-lasting performance.
( 27 )
$799.99
The next generation of air intakes is here! aFe Momentum GT Pro 5R air intake systems use the most up-to-date engineering tools and techniques to provide you with the perfect blend of power and protection. Their one-piece sealed housing with an auxiliary air scoop is designed to eliminate the use of multiple housings and ensure the coolest air intake charge available. A urethane plug is also included for those cold-weather applications where you want to block off the auxiliary air scoop. These systems feature premium stainless steel T-bolt clamps and a 2-ply, reinforced silicone coupler at the throttle body for increased strength and durability. They also include a 5-layer washable and reusable Pro 5R air filter. Experience maximum horsepower gains, huge low-end towing power, increased torque, and a throaty, mean growl for your performance machine with the Momentum GT Pro 5R air intake systems from aFe.
( 100 )
$836.00
—
$959.00
Centerforce dual friction clutches generate up to a 90 percent increase in holding capacity over stock systems. These clutch-and-disc sets are designed for engines producing high horsepower and big torque outputs. Perfect for 4WD vehicles, all Centerforce clutch systems provide smooth engagement and light pedal pressure without compromising high performance.
( 306 )
$1,049.95
—
$1,217.95
JBA Performance Exhaust competition-ready long tube headers are the number-one choice for maximum performance gains and high rpm efficiency. Their designs are dyno and race-proven to deliver the greatest possible increase in horsepower and torque throughout the rpm range. All JBA long tube headers feature large mandrel-bent stainless steel primary tubes, oversized exhaust ports, extra-thick 3/8 in. one-piece flanges, and patented merged collectors for smooth flow. Each system is designed to give the maximum amount of ground clearance possible so that lowered cars do not drag the collectors. And, in addition, each JBA system includes high-quality hardware and thorough instructions to provide a professional, no-leak installation.
( 97 )
$814.80
—
$1,082.70
Summit Bucks
Eaton Detroit Truetrac differentials use a patented design of parallel-axis planetary helix gears to provide a quiet, automatic splitting of torque. They perform like a limited-slip differential under normal driving conditions, automatically transferring torque to the wheel with better traction when ground conditions warrant. These replacement units are available for dozens of axle applications.
( 501 )
$923.99
—
$993.99
XClutch Stage 2 clutch kits offer performance upgrades for both street and track applications. Designed in-house, XClutch utilizes the latest ceramic technology in their Stage 2 kits offering either a cushioned or a sprung-style friction disc. They are mated with a high performance pressure plate and are recommended for vehicles requiring a higher level of torque holding and heat capacity. Features: * 1C cushioned ceramic—the discs offer a dampening layer between the two friction surfaces which is clamped together as the force of the pressure plate is exerted on the disc. This dampening along with a sprung hub offers drivability despite the ceramic friction surface. These kits are ideal for track cars that require some drivability or very high-horsepower street vehicles that require the added heat capacity of the ceramic friction material. * 1B sprung ceramic—these friction discs offer a sprung center to allow for drivability and are specifically designed for track use with minor street use. The kits offer great heat capacity due to the ceramic friction material and are available for a wide range of performance vehicles.
Not Yet Reviewed
$1,043.25
Made of 100 percent heavy-gauge aluminized steel, the Armor Lite Series exhaust systems from MBRP are designed to provide cost-conscious consumers with the same high-quality design and craftsmanship as the company's other systems—but at a value price. Armor Lite is suitable for areas with moderate environmental conditions. The high-flow performance systems maximize exhaust flow so your engine keeps its cool with lower exhaust temperatures. The result is greater fuel efficiency, more torque and horsepower, increased throttle response, and a sound that is pure MBRP. These bolt-on systems include stainless steel tips and welded on hangers. Order the model designed to fit your application.
( 13 )
$754.99
—
$909.99
Factory driveshafts are made from a smaller tube (there are 2 different types) and will flex and bend during hard acceleration, causing the rubber drives to wear out prematurely. The Driveshaft Shop torque tube driveshafts are made from 3 x .125 wall 6061 T-6 aluminum and uses The Driveshaft's own custom machined ends. This ensures that the shaft will not distort or break like the factory units, and offer units rated up to 1000 hp. Choose the driveshaft designed for your vehicle.
( 4 )
$771.62
—
$1,039.97
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
