Availability
Showing In Stock Items. Show All 17 Items.
On Sale
Add GM 6L80/90E transmission control to any existing vehicle utilizing a Terminator X Max ECU. A departure from traditional Holley EFI transmission control, the Terminator X Max ECU allows the ability to use 2007+ GM 6L80E and 6L90E transmissions by communicating via CAN with the internal TCM (Transmission Control Module). The supplied Holley EFI OBDII transmission tuning hand-held is used to adjust shift points, tire size and gear ratio. Terminator X V3 software provides the ability to dial in torque management to optimize the desired shifting characteristics when using a 6L80/90E transmission. The software also enables you to control the secondary shift mode within the transmission TCM and allows use of tap Up/Down shifting. Within Terminator X V3 PC Software: --- Virtual Torque Management Tables --- Virtual TPS Tables to dial in shift characteristics regardless of engine --- DBW and Timing torque reduction tables to create smooth shifts Within the Holley EFI OBDII Transmission Tuning Hand-held: --- Ability to read and clear TCM fault codes --- Ability to raise and lower shift points by MPH or RPM --- Support for Tap Up/Tap Down & Transmission's Secondary Shift Mode If you currently have a Terminator X ECU, upgrading to a Terminator X Max ECU can be easily done by plugging your main harness into the Max ECU and re uploading your existing calibration. Holley Terminator X MAX GM 6L80/90 transmission kit features: * Included TCM hand-held tuner with integrated wizard is required for setup in conjunction with the Terminator X 3.5 in. hand-held. Terminator X V3 software unlocks optional tuning parameters. * Plug-and-play with any engine controlled by a Terminator X Max ECU * Supports: Shift Mode - Tap Up / Tap Down, and torque management * Four loose wires: --- Power (Red): Supplies power to the transmission solenoids. This should be connected directly to the battery, or a constant battery source capable of supplying 5 amps --- Ground (Black): Connect to a good chassis/engine ground source --- Brake Switch (Light Blue/White): Wired to the brake light switch. This must be installed to a +12 V source (as most brake light switches are) --- Park/Neutral Safety (Yellow): Circuit for starter solenoid. When the transmission is in Park or Neutral, this yellow wire will be grounded (-). When the transmission is in gear this circuit will be open.
Not Yet Reviewed
$573.95
$515.95
On Sale
The Edge EZX module is the ultimate performance upgrade for your 5th Gen RAM Cummins, offering total control over your truck with power adjustability on-the-fly. With easy installation, improved fuel economy, better towing performance, and feature control through the industry's first smartphone app, you'll be amazed by what EZX can do for your truck. Compatible with both Standard and High Output engine variants, the throttle response and drivability are exactly what you want and need. This module is completely plug-and-play and leaves no trace within the system when removed for dealer service work. Engineered and developed specifically for the daily driver and towing application, EZX is a safe, emissions-friendly upgrade you'll wish you would've made sooner. With gains as much as 60 hp and 130 lbs.-ft. of torque, the EZX can be adjusted while driving through your factory steering wheel controls, allowing you to fine-tune your driving experience at your fingertips. Using the innovative smartphone app available for download through your app store (available for both Android and IOS), you gain even more access to your truck's features, including: calibrating for tire size and gear ratio changes, throttle pedal sensitivity, max cruise control speed, exhaust brake/tow haul button recall, TPMS settings, engine temperature protection, gear display, fog lights with high beams, and even a turbo timer! EZX app also allows you to read and clear trouble codes, check your emissions readiness status, and perform a manual DPF regen cycle. EZX offers features the competition just can't at a price point that's hard to beat! NOTE: When paired with the Insight CTS3 in kit form, the two devices still work independently of each other; and the Insight CTS3 will be used for monitoring only. All EZX control is still accomplished via the smartphone app and steering wheel. Product features: * 5 power levels adjustable on-the-fly through steering wheel controls * Engine high idle adjustable through steering wheel controls when in Park * User-adjustable throttle booster settings in each power level via app (Economy, Drive, Sport, Performance, Extreme) * Tire Size Speedo Calibration via app (Up to 40 in. tire size) * Tire Pressure Monitoring Sensors Enable/Disable, Warning On/Off, and Pressure Threshold adjust via app * Gear Ratio Calibration via App * Engine Coolant Protection Enable/Disable via app (Module adds no power until 120 degree ECT, backs down power at 240 degrees ECT) * Button Recall Enable/Disable via app; remembers Tow/Haul and Exhaust Brake settings * Turbo Timer Setup and Enable/Disable via app; once enabled, feature will work on every engine shutoff cycle * Max Cruise set speed adjustable via app (Set max cruise speed at 40-97 mph) * Fog Beams with High Beams Enable/Disable via app * Gear Display in Drive on factory display Enable/Disable via app * Manual DPF Regen via app * Read and clear ECM/TCM diagnostic codes via app * Check Emissions Readiness monitors via app
( 8 )
$649.95
—
$749.95
$529.95
—
$673.95
On Sale
COBB Tuning Ford Accessport V3 programmers have large, full-color, high-resolution screens that allow you to monitor up to six parameters in real time. They are fully customizable from the look (multiple bezel colors), layout (race, street, or dyno gauge clusters), and mounting options. The Accessport is the world's best-selling, most flexible, and easiest-to-use Ford ECU upgrade solution. Unlock power hidden within by replacing conservative factory settings with more aggressive calibrations. Follow COBB's staged upgrade path with pre-loaded off-the-shelf (OTS) maps or use custom-mapping for any modification level. COBB Tuning Ford Accessport V3 programmers feature: * In-vehicle mount, with on/off switch * Interchangeable faceplates * Simple installation: Everything is included; intuitive on-screen instructions identify your exact vehicle and available maps * Simple uninstall: Return your ECU to exactly as it was before with the easy-to-use Uninstall option from the main menu * Troubleshooting: Read codes, clear codes, identify vehicle, I/M readiness, keep alive memory, memory snapshot, reset ECU * Change maps: Store up to 100 maps from COBB's OTS map database or from your favorite COBB tuner; quickly switch between them for any need * Gauges: Use the Accessport as gauges to monitor boost or any other live information, directly from the ECU * Data logging: Record multiple data channels simultaneously for in-depth evaluation of engine performance; stores up to 10 hours * Performance measuring: Measure 0-60 time, 60-foot and 1/4 mile ETs, and trap speed * Shift light: Set custom RPM warning lights for perfect shifts * AP Manager: Download free; use a PC or Mac to manage maps, download data logs, or quickly update your Accessport Ford specific features: * Adjustable Traction Control: Adjust target slip on the fly and maximize grip to suit track conditions; enabled in ECU calibration * Flat Foot Shift: Improve shift times and maintain boost during shifts; hold engine RPM at a set level * Launch Control: Adjust on the fly with six pre-configured RPM slots based on track conditions and vehicle configuration * Change Map Slot: Allows instant changes to several calibration tables without re-flashing the ECU; each map slot is in a folder in the Map Switching Features group
( 7 )
$665.00
—
$770.00
$565.25
—
$654.50
On Sale
COBB Tuning Subaru Accessport V3 programmers have large, full-color, high-resolution screens that allow you to monitor up to six parameters in real time. They are fully customizable from the look (multiple bezel colors), layout (race, street, or dyno gauge clusters), and mounting options. The Accessport is the world's best-selling, most flexible, and easiest-to-use Subaru ECU upgrade solution. Unlock power hidden within by replacing conservative factory settings with more aggressive calibrations. Follow COBB's staged upgrade path with pre-loaded off-the-shelf (OTS) maps or use custom-mapping for any modification level. COBB Tuning Subaru Accessport V3 programmers feature: * In-vehicle mount, with on/off switch * Interchangeable faceplates * Simple installation: Everything is included; intuitive on-screen instructions identify your exact vehicle and available maps * Simple uninstall: Return your ECU to exactly as it was before with the easy-to-use Uninstall option from the main menu * Troubleshooting: Read codes, clear codes, identify vehicle, I/M readiness, keep alive memory, memory snapshot, reset ECU * Change maps: Store up to 100 maps from COBB's OTS map database or from your favorite COBB tuner; quickly switch between them for any need * Gauges: Use the Accessport as gauges to monitor boost or any other live information, directly from the ECU * Data logging: Record multiple data channels simultaneously for in-depth evaluation of engine performance; stores up to 10 hours * Performance measuring: Measure 0-60 time, 60-foot and 1/4 mile ETs, and trap speed * Shift light: Set custom RPM warning lights for perfect shifts * AP Manager: Download free; use a PC or Mac to manage maps, download data logs, or quickly update your Accessport * Accesstuner: Create custom calibrations using Accesstuner software; for modifications beyond COBB Stage Power Packages, custom tuning may be required. Subaru specific features (availability varies by model): * Realtime Tuning: Make changes to the map in real time, while the engine is running; speeds up the tuning process and allows quick changes to features like launch control and map switching * Launch Control: Set RPM threshold for performance launches; builds boost and generates instant horsepower off the line * Flat Foot Shifting: Keep the throttle on the floor and maintain boost between gears with this customizable RPM setting *Adjust Idle: Adjust idle on the fly to compensate for aftermarket parts; separate menus allow adjustment for A/C on and off * Adjust Timing (select STIs only): Globally reduce timing on the fly to compensate for poor-quality pump fuel * Launch Mode (some Forester XTs and WRX CVTs only): Allows manipulation of OE torque limiters to build boost and generate horsepower when launching; driver-controlled
( 4 )
$735.00
—
$770.00
$624.75
—
$654.50
On Sale
Superchips Pulsar XT Ford Bronco computer programmers control the following features: * Amber DRLs: This allows you to use the amber lights as your daytime running lights and turn signals. Stock, they are used only as turn signals. NOTE: DRLs will not be amber when your high beams or low beams are on. * Auto Start Stop Disable: Disables or enables the auto start/stop system on vehicles already equipped with it. * Battery Management System: Disables BMS. This will allow the battery to charge above the preset threshold. The vehicle will no longer warn you if your battery is getting low due to your headlights or radio being on. The side effect of disabling this system is the auto start stop system will also be disabled. * Dark Mode: Interior lights will remain off when the doors are opened. * Daytime Running Lights: Enable/disable DRLs * DTC Read/Clear: Feature will scan vehicle for Diagnostic Trouble Codes and report any found. Clear command will delete any present codes in the system * Emissions Readiness: This feature will check the current status of the vehicle's emissions readiness monitors. * Fog Lights with High Beams: Enables fog lights to stay on with high beams. * Headlamp Switch: The stock setting is for the vehicle to put the headlamp switch to "auto" when the vehicle is turned on. This will allow the vehicle to remember the previous setting after a key cycle. * Honk Warning: No longer honks if you leave the vehicle with the key if the engine is running. * Remote Start Duration: Change duration to 0, 5, 10, or 15 minutes. * Tire Size: Allows speedometer and odometer calibration for tire size changes up to 37 in. tall (36.25 in. measured). For most accurate results, measure tire height mounted on vehicle with a tape measure and input that reading, not what is printed on tire sidewall. * TPMS Adjust: Allows factory TPMS warning threshold to be adjusted between 1-99 psi. Use this feature if you want to run lower than factory tire pressure * TPMS Disable: This feature will completely turn off the TPMS system. Use when running below 25 psi or if tires are no longer equipped with TPMS sensors.
( 1 )
$671.95
$603.95
On Sale
COBB Tuning Volkswagen Accessport V3 programmers have large, full-color, high-resolution screens that allow you to monitor up to six parameters in real time. They are fully customizable from the look (multiple bezel colors), layout (race, street, or dyno gauge clusters), and mounting options. The Accessport is the world's best-selling, most flexible, and easiest-to-use Volkswagen ECU upgrade solution. Unlock power hidden within by replacing conservative factory settings with more aggressive calibrations. Follow COBB's staged upgrade path with pre-loaded off-the-shelf (OTS) maps or use custom-mapping for any modification level. COBB Tuning Volkswagen Accessport V3 programmers feature: * In-vehicle mount, with on/off switch * Interchangeable faceplates * Simple installation: Everything is included; intuitive on-screen instructions identify your exact vehicle and available maps * Simple uninstall: Return your ECU to exactly as it was before with the easy-to-use Uninstall option from the main menu * Troubleshooting: Read codes, clear codes, identify vehicle, I/M readiness, keep alive memory, memory snapshot, reset ECU * Change maps: Store up to 100 maps from COBB's OTS map database or from your favorite COBB tuner; quickly switch between them for any need * Gauges: Use the Accessport as gauges to monitor boost or any other live information, directly from the ECU * Data logging: Record multiple data channels simultaneously for in-depth evaluation of engine performance; stores up to 10 hours * Performance measuring: Measure 0-60 time, 60-foot and 1/4 mile ETs, and trap speed * Shift light: Set custom RPM warning lights for perfect shifts * AP Manager: Download free; use a PC or Mac to manage maps, download data logs, or quickly update your Accessport * Accesstuner: Create custom calibrations using Accesstuner software; for modifications beyond COBB Stage Power Packages, custom tuning may be required. Volkswagen specific features (availability varies by model): * Adjustable Traction Control: Adjust target slip on the fly and maximize tire grip to suit track conditions; enabled in ECU calibration * Flat Foot Shift: Improve shift times and maintain boost during shifts; hold engine RPM at a set level between 3000 and 8000 RPM; enabled in COBB OTS maps * Launch Control: Adjust on the fly with six pre-configured RPM slots to dial-in based on track conditions and vehicle configuration; enabled in OTS Maps and configurable within Accesstuner Pro
( 1 )
$735.00
—
$770.00
$624.75
—
$654.50
On Sale
COBB Tuning Mazda Accessport V3 programmers have large, full-color, high-resolution screens that allow you to monitor up to six parameters in real time. They are fully customizable from the look (multiple bezel colors), layout (race, street, or dyno gauge clusters), and mounting options. The Accessport is the world's best-selling, most flexible, and easiest-to-use Mazda ECU upgrade solution. Unlock power hidden within by replacing conservative factory settings with more aggressive calibrations. Follow COBB's staged upgrade path with pre-loaded off-the-shelf (OTS) maps or use custom-mapping for any modification level. COBB Tuning Mazda Accessport V3 programmers feature: * In-vehicle mount, with on/off switch * Interchangeable faceplates * Simple installation: Everything is included; intuitive on-screen instructions identify your exact vehicle and available maps * Simple uninstall: Return your ECU to exactly as it was before with the easy-to-use Uninstall option from the main menu * Troubleshooting: Read codes, clear codes, identify vehicle, I/M readiness, keep alive memory, memory snapshot, reset ECU * Change maps: Store up to 100 maps from COBB's OTS map database or from your favorite COBB tuner; quickly switch between them for any need * Gauges: Use the Accessport as gauges to monitor boost or any other live information, directly from the ECU * Data logging: Record multiple data channels simultaneously for in-depth evaluation of engine performance; stores up to 10 hours * Performance measuring: Measure 0-60 time, 60-foot and 1/4 mile ETs, and trap speed * Shift light: Set custom RPM warning lights for perfect shifts * AP Manager: Download free; use a PC or Mac to manage maps, download data logs, or quickly update your Accessport Mazda specific features: * Advanced Tuning Settings: Dial-in performance features on the Accessport; simply enable "Advanced Tuning Settings" * Launch Control: Builds boost and generates instant horsepower off the line; can be adjusted before each flash * Flat Foot Shift: Keep the throttle on the floor and maintain boost between gears; can be dialed-in before each flash * Wastegate Duty Cycle: Adjust during flashes (-50 to +10 percent) to correct under boost, over boost, and boost cut conditions (requires COBB OTS maps)
Not Yet Reviewed
$715.00
$607.75
Clearance
RaceChip GTS 5 Black chip tuning modules are the best of their kind for high-performance cars. State-of-the-art industry-grade hardware, up-to-the-minute software, ultra-modern technology (up to seven analog and digital channels), comprehensive safety and service package--everything a gearhead could want. Whether you are looking for an intensive driving experience on twisting cross-country roads, strong acceleration away from the lights, or raw power for the open road, RaceChip GTS 5 Black is the answer. Features: * Up to 30 percent more power and torque * Up to 20 percent increase mpg * Seven fine tuning mappings (selectable by Digital User Interface) * Motor-specific software * Warm-up timer preserves the engine * Engine Protect System+ * 2-year engine warranty (restrictions apply) * 5-year product warranty * One time re-programming included if you change your car (certain conditions apply) Hardware: * ARM Cortex-M3 processor * Up to seven analog and digital channels * Chip electronics with Nano-Protect * Pro-grade connector (FCI) * Ultra-resistant composite housing * Pro fixing system In the box: * RaceChip GTS 5 Black chip tuning module * Wiring kit * Four fixing clips * Four cable ties * User's manual
Not Yet Reviewed
$828.00
$579.50
On Sale
aFe Scorcher HD modules include a high-quality case and wire harness with factory-style connectors for an easy plug-and-play installation. An LED light switch provides in-cabin, on-the-fly power adjustments. The four power settings are adjustable with one button and the LED light represent the settings: stock (green), sport (yellow), sport+ (orange) and race (red). The aFe Scorcher HD modules add significant power by altering pressure sensor signals to increase turbo boost and fuel pressure to improve vehicle efficiency, power, and throttle response. They use a high-quality aluminum extrusion black powdercoated enclosure casing and factory-style connectors which requires no modification to your factory harness. These factory-style connectors plug directly into the stock wiring harness connectors and sensors.
( 2 )
$635.00
$571.50
With more than 25 years' experience in developing and manufacturing BCMs and over 100 million devices sold, Hella is one of today's leading global BCM suppliers. Hella body control modules (BCM) combine and manage comfort and safety functions as well as the power management system. They also provide the diagnostic interface when repairing or servicing the vehicle. Whenever the driver turns on the lights, heats up his seat, or uses the windscreen wipers, the BCM acts as the control center. Inside a well-equipped mid-range car, the BCM communicates with about 60 different ECUs. As part of an integrated energy management system, it helps to minimize the vehicle's overall energy consumption. Hella body control modules thus help to reduce a vehicle's overall CO2 emissions, supporting you in achieving your environmental, cost, functional, and quality targets.
Not Yet Reviewed
$540.99
—
$747.99
On Sale
Introducing the Superchips TrailDash 3 computer programmers for Jeep Wrangler and Gladiator! Built off the success of their TD2, the all-new TD3 offers a state-of-the-art display with a high-res 5 edge-to-edge full-color swipe screen. Using the latest monitoring technology, TD3 offers a clean and sharp display unlike anything on the market for Jeep owners today. The new, larger processor means faster tune loads, quicker response times, and the best user experience Superchips has ever offered. TD3 is also now Wi-Fi equipped, making internet updates a breeze. The new screen layout has been perfected to complement the look and feel of your Wrangler and Gladiator. The all-new CRAWL screen offers easy access to the data and off-road features you need most, like Sway Bar Disconnect, Axle Lockers, TPMS Disable, Rock Lock, Line Lock, and Engine Idle Up. Of course TD3 still offers tire size and gear ration adjustment—along with tried and true performance tuning for better power, torque, and mileage from your Jeep regardless the situation. You can also optimize your experience with the addition of a broad array of EAS accessories for extra power switches, back-up camera, and additional pressure or temperature sensors. Remember, 2015-21 Wranglers and Gladiators do require a PCM swap process and a unique set of steps required before tuning. It is extremely important you review and understand the steps required before you enjoy the tremendous power and functionality now available with TD3. Order the model recommended for your Jeep.
Not Yet Reviewed
$699.00
$628.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
