Availability
Showing In Stock Items. Show All 37 Items.
On Sale
Holley SBF Hi-Ram EFI intake manifolds with side-mount tops are available for the 8.2 in. or 9.5 in. SBF Ford applications, and come with either a 95mm or 105mm Ford 5.0L throttle body flange side-mount top. The runner length and tapered cross-section design will perform well for a wide range of engine configurations. Holley's engineering team redesigned the water crossover passage to allow room for distributor phasing. The SBF Hi-Ram EFI intake manifolds have aggressive, bold, race-bred styling that's perfect for drag race, muscle car, off-road, pulling trucks, street rod applications, and more! Additional features and specs include: * Cast aluminum construction with satin silver finish * Designed for side-mounted throttle bodies (Ford 5.0L throttle body fitment) * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system; they come standard with EFI Hi-Ram kits * Plenum top gasket type: 3/32 in. round O-ring cord * Allows room for designing boosted applications * A low-profile distributor will be needed when using this manifold
Not Yet Reviewed
$1,249.95
$687.95
Edelbrock Performer EPS intake manifold and carburetor kits contain all of the necessary pieces to upgrade your induction system. They include an Edelbrock Performer EPS aluminum intake manifold with either a natural aluminum finish or an EnduraShine finish, an intake gasket set, intake manifold bolts, a carburetor stud kit, and a Performer Series 600 cfm electric choke carburetor. The EnduraShine finish is a bright silver chrome finish that resists discoloration from heat and features a clearcoated top coat to enhance abrasion and chemical resistance. The Edelbrock Performer EPS intake uses an all-new runner design tuned to produce substantial torque increases. Ready for a change? Try Edelbrock Performer EPS intake manifold and carburetor kits for your musclecar, hot rod, truck, or ordinary street vehicle.
( 60 )
$830.95
For maximum performance in normally aspirated competition applications, Weiand Hi-Ram Tunnel Ram intake manifolds are the manifold of choice. They're designed primarily for drag racing, truck/tractor pulls, and performance marine applications where high rpm is required but bottom-end torque isn't. With their patented D-shaped port runners and large plenum chamber, the manifolds provide optimum thrust of the air/fuel mixture to the intake ports. They mount either single or dual square-mount carbs and, depending on the application, have power bands that run from 2,500 rpm to as high as 9,000 rpm. Separate tops and runners are available for some manifolds. Order the model recommended for your year/make, engine, and cylinder head application.
( 27 )
$649.95
—
$699.95
Trick Flow® R-Series A460 Tunnel Ram Intake Manifolds were developed for all 8,000 plus rpm applications such as drag racing and tractor pulling. They feature a 2-piece design with interchangeable top covers so you can mount either single or dual Dominator-style carbs. They're made from thick-wall A319 aluminum for durability and the lower manifold feature bosses for nitrous and fuel injection nozzles. The lower manifold and top covers are sold separately; both pieces are required to make a complete manifold assembly. R-Series A460 manifolds can only be used with Trick Flow® PowerPort® A460 series cylinder heads.
( 2 )
$849.99
BluePrint / Holley Sniper EFI fabricated intake manifolds continue to push the aftermarket with low-profile intakes for the popular GM LS engine family. They're good looking, perform well, and offer great value for a performance sheet metal style intake manifold. Each unit is ready to bolt on out of the box, is designed to accept Sniper high-flow throttle bodies, and includes a high-flow fuel rail kit. This updated design was developed to allow the end user to fit under a stock hood. Each manifold is precision fixtured, welded for a perfect fit and maximum structural integrity. Your choice of throttle body opening sizes of 92mm and 102mm are available. Additional details: * Low-profile design (overall 1.875 in. shorter) allows fitment under stock hoods on Corvette, Camaro, Firebird, GTO, and others where hood clearance is at a minimum * Shortened runners allow for compact design. Overall plenum volume maintained by increasing the overall width of the plenum and increasing the overall dimensions of the runner * 3mm (1/8 in.) thick T6061 sheet aluminum construction, strong and durable even under high horsepower and boosted conditions * 100 percent TIG-welded * Intakes include 3/8 in. fuel rail kits with -8 AN fittings and crossover braided line capable of supporting 750+ horsepower (laser-engraved Sniper logo) * Runner lengths with tapered top on EFI intakes designed to increase velocity and more evenly distribute airflow to all 8 cylinders
Not Yet Reviewed
$569.95
Edelbrock Victor Ram intake manifolds specialize in the control of high velocity mixture flow, especially at engine speeds above 8,500 rpm. Removable top mounts various carburetors. They are suited to drag race engines operating at 6,500-10,000 rpm and race boat engines above 7,000 rpm.
( 1 )
$605.95
On Sale
Holley Sniper EFI fabricated intake manifolds are budget-friendly and performance laden! These durable Holley hi-ram manifolds feature 3mm (1/8 in.) thick T-6061 sheet aluminum construction with 100 percent TIG welds. The EFI versions have 92mm or 102mm throttle body openings, as well as runners with tapered tops to increase velocity and evenly distribute airflow. They also include 3/8 in. fuel rail kits and, of course, are branded with the Holley Sniper EFI logo. Budget and performance go hand-in-hand when it comes from Holley in the form of their Sniper EFI fabricated intakes. Order the model and options recommended for your make/engine application.
( 17 )
$899.95
$552.95
—
$799.95
AFR Eliminator Series intake manifolds are the perfect way to "eliminate" your competition! These cast aluminum performance intakes have a 23-degree manifold configuration. They're designed for standard location intake port cylinder heads. Additional coolant outlets have been added at the rear of the manifold for custom cooling systems. Eliminator intakes can be run "as cast," right out of the box; however, AFR does recommend having the runner exits be "port matched" to your particular cylinder heads for optimal performance. Additional bungs have been cast into the top of the intake runners for EFI injectors or nitrous nozzles. Multiple heights and rpm ranges are available; order the manifold recommended for your application.
( 23 )
$669.90
On Sale
Make Holley SBF Hi-Ram EFI intake manifold bases the foundation for your custom induction system. Their modular design allows them to accept a variety of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. Aggressive looks and bold styling make your bad intentions clear—whether you're drag racing, truck pulling, or making waves in your boat—when you start with the Holley Hi-Ram EFI intake manifold bases. SBF Hi-Ram EFI intake manifold base features and specs: * Manifold base only designed for 8.2 in. deck height * Cast aluminum construction * Available in natural cast aluminum (satin) or black powdercoat finish * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system
( 1 )
$996.95
—
$1,049.95
$648.95
—
$682.95
On Sale
Holley is the new standard in EFI! The Holley EFI LT1 Gen V Lo-Ram intake manifolds are designed for GM Gen V LT engines equipped with GM LT cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine application. The top-feed plenum base intake manifold is designed with a reduced overall height to fit under a stock or mildly modified hood. The Lo-Ram provides a low-profile modular intake manifold that's suitable for use with plenum mounted air-to-water intercoolers for boosted applications. Various Hi-Ram plenum top options are available to complement the top-feed base intake manifold kits and fabrication flanges are offered to aid fabrication of plenum tops for custom installations. Features: * Designed for GM Gen V engines equipped with GM LT type cylinder heads * As-cast aluminum (satin) and black powdercoat finishes available * 105mm diameter throttle body opening accepts OEM 4-bolt LS/LT DBW or Holley LS/LT throttle bodies * Engineered for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000-8,000 rpm, depending on the application * Low-height top-feed plenum profile to fit under a stock or mildly modified hood * Modular design and top entry plenum flange allows the use of popular Holley Hi-Ram plenum tops, as well as facilitating custom fabricated plenum tops—base manifold, plenum tops, and fabrication flanges available as separate kits * Designed for the accommodation of plenum mounted air-to-water intercoolers for boosted applications * Available models for OE direct fuel injection only and with port fuel injection provisions—for the port fuel injection option, the high-volume fuel rail kit includes hardware and brackets to accommodate long (usually standard length) fuel injectors or short * Kits with port injection provide high volume fuel rails with 3/4 in.-16 O-ring ports (8 AN) * Mounting hardware is included * 3.18 in. taller than a factory LT1 manifold
( 1 )
$1,049.95
$549.95
—
$749.95
The design of Holley Hi-Ram GM LT1 lower manifolds allows for easy disassembly to do custom porting, use multiple tops, or create custom induction systems. Each runner has a large radius where it meets the plenum, as well as an optimized taper and cross-sectional area to perform in a wide variety of engine configurations. The bases are available with or without port EFI provisions. Are you looking for the ultimate performance? Begin with Holley LT Modular Hi-Ram lower intake manifolds. Features include: * Modular design with removable top * Overall height: 13.34 in. with EFI top (95mm or 105mm) * Overall height: 12.10 in. with carb-style top (2 x 4150 or 2 x 4500) * Height at plenum flange: 9.44 in. * Port size: 2.06 in. high x 1.53 in. wide * Runner length: approximately 6.5 in. * Large plenum volume of 549 cu. in. with 1 x 95mm or 1 x 105mm throttle body top * Available with or without injector ports in the runners * Intakes with injector ports include fuel rails with dual mounting (1.48 in. or 2.56 in.) O-ring to O-ring injector length * Anodized fuel rails, laser-etched, and machined for -8 AN O-ring fittings * Rear of plenum machined for MAP and three vacuum ports * Head flange has clearance for fuel supply to a high-pressure pump * Increased runner wall thickness for custom porting at the plenum-to-runner entry on each runner * O-ring seals at cylinder heads and plenum top * Top-mounted screws on plenum top (all except front two screws) * Available top options: 1 x 95mm, 1 x 105mm, 2 x 4150, 2 x 4500, or blank flange for custom throttle bodies (all sold separately) * 3,500-8,000+ rpm power band
Not Yet Reviewed
$749.95
Holley Ford Hi-Ram carbureted intake manifold bases have a runner length and tapered cross section designed to perform well for a wide range of engine configurations. Holley's engineering team also redesigned the water crossover passage to allow room for distributor phasing. Aggressive, bold, race-bred styling will make bad intentions clear for drag race, muscle car, marine, off-road, sandrails, pulling trucks, track, street-rod applications and more! Holley Hi-Ram specs: * Cast aluminum construction * Available in natural or black finish * Plenum top gasket type—3/32 in. round O-ring cord
( 2 )
$728.95
—
$799.95
On Sale
Holley EFI Coyote Ultra Lo-Ram intake manifolds are designed to fit stock bolt pattern OE heads found on the 2011-23 Ford 5.0 Coyotes and related engine families, such as Voodoo and Predators. These kits include fuel rails for use with OEM-type fuel injectors and clips, mounting hardware, and O-ring gaskets. Offered in black and natural as-cast finish, the manifolds have a 9.20 in. runner length and are designed to improve the mid to high RPM powerband. The Ultra Lo-Ram provides an additional 19.4mm front and 42.6mm rear clearance compared to the Ford Performance Cobra Jet manifold—plus clears 2015-23 Mustang factory hoods. They're offered in both round and oval throttle body configurations, with replacement front inlets for easy interchangeability. The oval inlet can accommodate up to a 150 x 66mm single throttle body and 93mm on the round variant. Round inlets include standard mounting provisions for GT350, GT500, and LS 4-bolt throttle bodies. 2011-23 GT throttle bodies can be used with the optional 717-18 adapter. (NOTE: Coyote Ultra Lo-Ram intake manifolds are available with the base only, no top included, if desired. See "Intake Section Included" tabs.) Product features: * As-cast aluminum construction: more durable for boosted applications, can be welded for modifications * Modular design: accessible runner entries for porting, allows accessories like intercoolers and nitrous plates * 300-911 and 300-912 Ultra Lo-Ram will fit under stock hood with stock engine mounts in 2015-23 Mustang * Refined port design with streamlined injector boss for reduced turbulence without loss of flow area * Allows a variety of throttle valves, including large monoblade, 2015-20 GT350, 2007-14 GT500, 2019-23 GT500, GM LS 4-bolt, 2011-23 Ford Mustang GT (with optional adapter PN 717-18) * Fuel rails with -8 AN ports and dual 1/8 NPT accessory ports for gauges or Gen 3 direct injection fuel line hookup
( 1 )
$924.95
$508.95
—
$620.95
Holley LS Modular Hi-Ram intake manifold bases could be the foundation for your custom induction system. Aggressive looks and bold styling make your bad intentions clear, whether you're drag racing, truck pulling, or making waves in your boat when you start with one of these Hi-Ram bases. Their modular design allows them to accept a wide range of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. When there's no limit on height, start your build with one of Holley's cost-effective LS Modular Hi-Ram intake manifold bases.
( 2 )
$771.95
—
$775.95
On Sale
Holley is the new standard in EFI! The Holley EFI LT1 Gen V Ultra Lo-Ram intake manifold kits are designed for GM Gen V LT engines equipped with GM LT cylinder heads. They will work with OE or aftermarket cylinder heads. The Ultra Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications. The front-feed base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood. The Ultra Lo-Ram provides a very low-profile modular intake manifold along with various fabrication flanges to aid the fabrication of special throttle body adapters or inlet ducts for custom installations. Whether you're engine swapping your classic car or need to manage added horsepower in your twin-turbocharged drag radial race car, Holley EFI has the solutions you need to get your project up and running better than ever! Features: * Designed for GM Gen V engines equipped with GM LT type cylinder heads * As-cast aluminum (satin) and black powdercoat finishes available * 105mm diameter throttle body opening accepts OEM 4-bolt LS/LT DBW or Holley LS/LT throttle bodies * Engineered for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000-8,000 rpm depending on the application * Only 0.97 in. taller than a factory LT1 manifold provides maximum clearance under a stock or mildly modified hood * Modular design and front entry plenum flange allows design and fabrication of special throttle body adapters or inlet ducts for custom installations—base manifold, plenum top, throttle body adapter available as separate kits * Clears C7 Corvette cowls and hoods without modification * Available for OE direct fuel injection only or with added port fuel injection provisions * Kits with port injection provide high volume fuel rails with 3/4-16 O-ring ports (8 AN). Mounting hardware is included * Ultra Lo-Ram kits with a burst panel flange are available, Ultra Lo-Ram billet burst panel duct is offered separately (PN: 300-608 clear anodized, PN: 300-608BK black anodized)
Not Yet Reviewed
$1,049.95
$558.95
—
$649.95
Holley EFI Coyote Hi-Ram intake manifolds are available with the BASE ONLY, no top included, if desired. The aluminum bases are offered in a black or natural finish. However, if you want the complete intake manifold system, here is the description: Holley EFI Coyote Hi-Ram intake manifolds are designed to fit stock bolt pattern OE heads found on the 2011-23 Ford 5.0 Coyotes and related engine families, such as Voodoo and Predators. These kits include fuel rails for use with OEM-type fuel injectors and clips, mounting hardware, and O-ring gaskets. Offered in black and natural as-cast finishes, the manifolds have a 9.20 in. runner length and are designed to improve the mid to high RPM powerband. The aggressively designed Hi-Ram is constructed in a two-piece design to accommodate for air to water intercoolers and feature up to 20 percent more plenum volume versus Ultra Lo Rams. This manifold design is only offered in an oval throttle body configuration. Product features: * As-cast aluminum construction: more durable for boosted applications, can be welded for modifications * Modular design: accessible runner entries for porting, allows accessories like intercoolers and nitrous plates * Refined port design with streamlined injector boss for reduced turbulence without loss of flow area * Allows a variety of throttle valves, including large monoblade, 2015-20 GT350, 2007-14 GT500, 2019-23 GT500, GM LS 4-bolt, 2011-23 Ford Mustang GT (with optional adapter 717-18) * Fuel rails with -8 AN ports and dual 1/8 NPT accessory ports for gauges or Gen 3 direct injection fuel line hookup * Plenum Volume: 300-910 / 9.8-liters * Two 1/8 NPT ports on all manifolds. Two 3/8 NPT ports on all manifolds
Not Yet Reviewed
$574.95
—
$620.95
On Sale
Holley Sniper EFI fabricated Race Series intake manifolds utilize a larger intake plenum for max effort engines and boosted applications. These manifolds feature 5mm (13/64 in.) thick T-6061 sheet aluminum construction with 100 percent TIG welds. With their removable tapered top, increased velocity and more evenly distributed airflow to all cylinders is a guarantee! Race Series intakes also include 3/8 in. fuel rail kits, -8 AN fittings, and crossover-braided line capable of supporting 750+ hp. They're available in multiple anodized colors, and every manifold has the Holley Sniper EFI logo.
( 1 )
$1,449.95
$797.95
These Performer RPM FE intake manifolds from Edelbrock are designed for high-performance street Ford FE V8s with standard low/medium-rise or Edelbrock Performer RPM FE heads. Their dual-plane constant cross-sectional area design builds low and mid-range acceleration, while optimized runner paths make top-end horsepower. These manifolds have a provision for adding the PCV or breather flange at the rear, and no exhaust crossover passage.
( 37 )
$736.95
—
$865.95
Dual plane Chevrolet Performance Parts' Carbureted LT1 intake manifolds make it possible to take advantage of the advancements found in Generation 2 Chevy engines. They allow you to install a carburetor on your LT1 engine without the hassle of running a computer or emission controls. They accept both Holley and Quadrajet carburetors, and feature longer runners that increase engine torque by up to 30 ft.-lbs. without sacrificing top-end power.
( 28 )
$507.67
Edelbrock Performer RPM intake manifolds have a high-rise, dual-plane design. They produce incredible top-end horsepower, while retaining good throttle response. Performer RPMs have larger plenums and runners to match the free-flowing exhaust, high-lift cams, and other modifications of a high-output engine. They're intended for high performance street or competition engines that run from 1,500 to 6,500 rpm.
( 221 )
$514.95
—
$689.95
These Edelbrock CH-28 dual quad intake manifolds are designed for 413, 426, and 440 c.i.d. Chrysler V8s. Use them with the Performer-Plus cam for more low-end torque, or the Torker-Plus cam for more top-end power. They will not fit 1962-64 Max Wedge cylinder heads. Carb center to carb center is 6 7/16 in.
( 1 )
$530.95
Dorman intake manifolds are precision-engineered and durably manufactured to match the fit and function of the original manifold on specified vehicles. They are thoroughly tested to ensure top-quality OEM construction and superior reliability. Dorman manifolds are offered in different styles, and all will provide a trustworthy design with a perfect fit and reliable construction for your vehicle.
( 156 )
$625.95
Edelbrock Victor spread-port intake manifolds are specifically designed for high-rpm drag racing engines using Brodix Big Duke or Dart Big Chief cylinder heads. They feature a runner section area of approximately 4.75 sq. in. The intake manifolds require port matching to the cylinder head for optimum performance and will produce higher top-end horsepower while maintaining consistency and throttle response.
Not Yet Reviewed
$887.95
—
$897.95
On Sale
Holley LS 2x4 dual plane fuel injection intake manifolds allow you to install dual throttle bodies on your late model LS Series engines. Their dual plane, equal-distribution layout produces great midrange torque without compromising top-end power. The manifolds feature all cast aluminum construction, a wide 1,500 to 7,000 rpm power band range, and can accept dual inline mounted 1,000 cfm throttle bodies with a 1.750 in. maximum throttle bore diameter.
Not Yet Reviewed
$799.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
