Availability
On Sale
Holley's EFI crank trigger kits provide accurate crank speed and position signals to Holley EFI systems in the most demanding, high-horsepower, racing applications. The crank position is measured every 10 degrees instead of every 45 degrees, like standard 4-magnet crank trigger systems. Holley's EFI crank trigger kits feature 1/4 in. thick, billet steel, 36-1 or 60-2 tooth-crank trigger wheels with black zinc oxide finish for superior corrosion resistance and striking good looks Other notable features include: * Crank wheels center off of balancer hubs, eliminating the need for centering rings * All billet, 6061-T6 aluminum sensor mounting brackets with "bright-dipped" black anodized finish and laser-etched Holley EFI logo * Custom 3-wire, ferrous-target, Hall-effect sensors with M12 x 1.0mm threads for finer gap adjustment * Grade 8 and mil-spec mounting hardware
( 6 )
$675.95
$583.95
—
$749.95
On Sale
Holley LS split design carbureted intake manifolds are single-plane racing units designed with performance in mind. They feature a race-bred, 2-piece split feature that was previously only found on the most expensive race intakes. The manifolds will fit GM LS Gen III engines with cathedral port heads—and are intended for 4150-style square bore flanged carburetors or throttle body EFI. The LS Race single-plane intake manifold was designed for high performance/racing engine applications, 5.3 to 6.2+ liter displacement—and maximum engine speeds of 6,000 to 7,000 rpm, depending on the engine combination. This single-plane design provides optimal performance across the rpm spectrum, while providing maximum performance up to 7,000 rpm. Features include: * Maximum performance race design with hood clearance consideration * Lighter than other split race intakes * Split feature allows disassembly of the intake for direct access to internal plenum and port surfaces, making custom porting and matching a snap * Shoulder bolt locators and O-ring seal make reassembly simple and precise * 33 to 50 percent the price of other split race intakes * Vacuum port options: Two 1/8 in., one 1/4 in., and one 3/8 in. NPT ports at the carb flange
( 6 )
$725.95
$583.95
—
$749.95
On Sale
Holley LS Modular Lo-Ram EFI intake manifolds are designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications and a 105 mm throttle or similar models. The base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood in the front-feed configuration. The modular design allows the use of front-feed plenum entry, while intake design facilitates custom inlet duct and throttle body placement. Additional features and specs: * Cast aluminum construction with satin silver finish * Modular design allows the use of front-feed plenum entry * Clears 4th Gen Camaro and C5 Corvette cowls and hoods without modification * With forced-induction and the short runner length the engine rpm at which peak power occurs is more likely to be coupled to the supercharger or turbocharger being used * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits include two sets of brackets; a set for long (usually standard length) fuel injectors and a set for short (such as Pico, or LS7) fuel injectors
( 8 )
$649.95
—
$749.95
$583.95
—
$673.95
On Sale
Holley is the new standard in EFI! The Holley EFI LT1 Gen V Lo-Ram intake manifolds are designed for GM Gen V LT engines equipped with GM LT cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine application. The top-feed plenum base intake manifold is designed with a reduced overall height to fit under a stock or mildly modified hood. The Lo-Ram provides a low-profile modular intake manifold that's suitable for use with plenum mounted air-to-water intercoolers for boosted applications. Various Hi-Ram plenum top options are available to complement the top-feed base intake manifold kits and fabrication flanges are offered to aid fabrication of plenum tops for custom installations. Features: * Designed for GM Gen V engines equipped with GM LT type cylinder heads * As-cast aluminum (satin) and black powdercoat finishes available * 105mm diameter throttle body opening accepts OEM 4-bolt LS/LT DBW or Holley LS/LT throttle bodies * Engineered for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000-8,000 rpm, depending on the application * Low-height top-feed plenum profile to fit under a stock or mildly modified hood * Modular design and top entry plenum flange allows the use of popular Holley Hi-Ram plenum tops, as well as facilitating custom fabricated plenum tops—base manifold, plenum tops, and fabrication flanges available as separate kits * Designed for the accommodation of plenum mounted air-to-water intercoolers for boosted applications * Available models for OE direct fuel injection only and with port fuel injection provisions—for the port fuel injection option, the high-volume fuel rail kit includes hardware and brackets to accommodate long (usually standard length) fuel injectors or short * Kits with port injection provide high volume fuel rails with 3/4 in.-16 O-ring ports (8 AN) * Mounting hardware is included * 3.18 in. taller than a factory LT1 manifold
( 1 )
$1,049.95
$579.95
—
$749.95
On Sale
Holley modular LS Pontiac-style valve covers feature an OE height, internally-baffled base with integrated coil mounts for popular Gen I and Gen V-style LS coil bodies. The overcovers hide the unsightly LS coils and messy wiring harness—allowing the full performance benefits of coil-on-cover ignition setups without the robotic styling. Each modular coil cover features a simulated oil fill cap which helps maintain the original Pontiac styling. The coil cover also features cast-in provisions for the spark plug boots and coil wiring harness, so no extensions or custom wiring is required. Holley's 2-piece LS Pontiac-style valve covers offer a great way to update the look of your LS engine without the use of complicated adapter systems or the hassle of remote coil relocation! More product features and items include: * Available in various finishes * Base fits LS1, LS2, LS3, LS6, and LS7 engines with clearance for 0.750 in. lift cam with stock style rocker arms * Base features internally baffled ventilation system * Each 2-piece LS valve cover set includes a low-profile billet oil fill cap, 2 billet simulated fill cap assemblies, hardware, and spacers for mounting both versions of LS coil bodies * Dress-up hardware and rubber grommets for the coil covers
( 1 )
$586.95
$527.95
—
$599.95
On Sale
Developed with performance in mind, Holley EFI LS single plane split-design race intake manifolds feature a race bred, 2-piece split design that was previously found only on the most expensive race intakes. These manifolds will fit GM LS Gen III engines with cathedral port heads for high performance/racing engine applications with 5.3 to 6.2 liter displacement and maximum engine speeds of 6,000 to 7,000 rpm, depending on the engine combination. The single-plane design provides optimal performance across the rpm spectrum, while the split feature, which allows disassembly of the intake for direct access to internal plenum and port surfaces, makes custom porting and matching a snap. Shoulder bolt locators and an O-ring seal makes reassembly simple and precise.
( 4 )
$821.95
$628.95
—
$738.95
On Sale
You will not find an easier way to upgrade your fuel system than the Holley Sniper OE Style 350 LPH EFI Fuel Pump Modules. They are a direct replacement that fits your factory fuel tank, so you don't have to guess when it comes to something as important to your project as the fuel system. Because it was designed as a direct replacement for your factory pick-up and sending unit, there is no need to purchase a custom EFI fuel tank. You can even retain your factory fuel line. Simply connect the outlet of the pump module to the hard line on your vehicle with EFI-rated fuel hose and hose clamps available in the Earl's Vapor Guard Line. Features: * The in-tank fuel pump module is a high-pressure unit that flows 350 liters per hour (LPH) and is capable of supporting EFI (electronic fuel injection) engines producing up to 750 horsepower * Includes a pre-calibrated fuel-level sending unit designed to work with the factory fuel gauge for your application * Solves all the usual issues of converting from carburetor to EFI
( 28 )
$649.95
$558.95
—
$649.95
On Sale
Make Holley SBF Hi-Ram EFI intake manifold bases the foundation for your custom induction system. Their modular design allows them to accept a variety of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. Aggressive looks and bold styling make your bad intentions clear—whether you're drag racing, truck pulling, or making waves in your boat—when you start with the Holley Hi-Ram EFI intake manifold bases. SBF Hi-Ram EFI intake manifold base features and specs: * Manifold base only designed for 8.2 in. deck height * Cast aluminum construction * Available in natural cast aluminum (satin) or black powdercoat finish * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system
( 1 )
$996.95
—
$1,049.95
$648.95
—
$682.95
On Sale
The design of Holley Hi-Ram GM LT1 lower manifolds allows for easy disassembly to do custom porting, use multiple tops, or create custom induction systems. Each runner has a large radius where it meets the plenum, as well as an optimized taper and cross-sectional area to perform in a wide variety of engine configurations. The bases are available with or without port EFI provisions. Are you looking for the ultimate performance? Begin with Holley LT Modular Hi-Ram lower intake manifolds. Features include: * Modular design with removable top * Overall height: 13.34 in. with EFI top (95mm or 105mm) * Overall height: 12.10 in. with carb-style top (2 x 4150 or 2 x 4500) * Height at plenum flange: 9.44 in. * Port size: 2.06 in. high x 1.53 in. wide * Runner length: approximately 6.5 in. * Large plenum volume of 549 cu. in. with 1 x 95mm or 1 x 105mm throttle body top * Available with or without injector ports in the runners * Intakes with injector ports include fuel rails with dual mounting (1.48 in. or 2.56 in.) O-ring to O-ring injector length * Anodized fuel rails, laser-etched, and machined for -8 AN O-ring fittings * Rear of plenum machined for MAP and three vacuum ports * Head flange has clearance for fuel supply to a high-pressure pump * Increased runner wall thickness for custom porting at the plenum-to-runner entry on each runner * O-ring seals at cylinder heads and plenum top * Top-mounted screws on plenum top (all except front two screws) * Available top options: 1 x 95mm, 1 x 105mm, 2 x 4150, 2 x 4500, or blank flange for custom throttle bodies (all sold separately) * 3,500-8,000+ rpm power band
Not Yet Reviewed
$749.95
$673.95
On Sale
Holley's 2-piece LS valve covers are a great way to update the look of your LS engine without the use of complicated adapter systems or the hassle of remote coil relocation. These modular LS valve covers feature an OE height, internally baffled LS valve cover base with integrated coil mounts for popular Gen I and Gen V style LS coil bodies, and a Ford style overcover that hides the unsightly LS coils and messy wiring harness. This allows the full performance benefits of coil-on-cover ignition setups without the robotic styling. These coil covers also feature cast-in provisions for the spark plug boots and coil wiring harness, so no extensions or custom wiring is required. Each 2-piece LS valve cover set includes a low-profile billet oil fill cap, hardware and spacers for mounting both versions of LS coil bodies, plus dress-up hardware and rubber grommets for the coil covers. The modular LS valve covers are available in three custom finishes: natural cast, polished, and satin black. Features: * Cast aluminum 2-piece LS valve covers designed to mount and hide both Gen I and Gen V style LS coil bodies * Retain the performance of factory coil-on-cover ignition without the unsightly styling * Coil cover features vintage Ford valve cover styling and cast-in wiring provisions * Base fits LS1, LS2, LS3, LS6 and LS7 engines with clearance for .750 in. lift cam with stock-style rocker arms * Base features internally baffled ventilation system * No coil relocation, wire harness extensions, or custom spark plug wires required * Includes low-profile billet oil fill cap * Includes all necessary coil mounting provisions and dress-up hardware
Not Yet Reviewed
$573.95
$515.95
On Sale
Holley Sniper carbureted fabricated intake manifolds are budget-friendly, sheet metal style intake manifolds. Each manifold is precision-fixtured and welded for a perfect fit and structural integrity. They are available for carbureted Chevy LS, Ford Coyote, small block Chevy, big block Chevy, and small block Ford engines. Features include: * Available for single or dual carburetor applications * 3mm (1/8 in.) thick T6061 sheet aluminum construction * More durable than competitive intakes * Bead-blasted silver or black anodized finishes * 100 percent TIG-welded * Custom Holley Sniper logo
( 37 )
$912.95
$502.95
—
$707.95
On Sale
Holley is the new standard in EFI! The Holley EFI LT1 Gen V Ultra Lo-Ram intake manifold kits are designed for GM Gen V LT engines equipped with GM LT cylinder heads. They will work with OE or aftermarket cylinder heads. The Ultra Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications. The front-feed base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood. The Ultra Lo-Ram provides a very low-profile modular intake manifold along with various fabrication flanges to aid the fabrication of special throttle body adapters or inlet ducts for custom installations. Whether you're engine swapping your classic car or need to manage added horsepower in your twin-turbocharged drag radial race car, Holley EFI has the solutions you need to get your project up and running better than ever! Features: * Designed for GM Gen V engines equipped with GM LT type cylinder heads * As-cast aluminum (satin) and black powdercoat finishes available * 105mm diameter throttle body opening accepts OEM 4-bolt LS/LT DBW or Holley LS/LT throttle bodies * Engineered for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000-8,000 rpm depending on the application * Only 0.97 in. taller than a factory LT1 manifold provides maximum clearance under a stock or mildly modified hood * Modular design and front entry plenum flange allows design and fabrication of special throttle body adapters or inlet ducts for custom installations—base manifold, plenum top, throttle body adapter available as separate kits * Clears C7 Corvette cowls and hoods without modification * Available for OE direct fuel injection only or with added port fuel injection provisions * Kits with port injection provide high volume fuel rails with 3/4-16 O-ring ports (8 AN). Mounting hardware is included * Ultra Lo-Ram kits with a burst panel flange are available, Ultra Lo-Ram billet burst panel duct is offered separately (PN: 300-608 clear anodized, PN: 300-608BK black anodized)
Not Yet Reviewed
$1,049.95
$558.95
—
$649.95
On Sale
Holley LS Modular Hi-Ram intake manifold bases could be the foundation for your custom induction system. Aggressive looks and bold styling make your bad intentions clear, whether you're drag racing, truck pulling, or making waves in your boat when you start with one of these Hi-Ram bases. Their modular design allows them to accept a wide range of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. When there's no limit on height, start your build with one of Holley's cost-effective LS Modular Hi-Ram intake manifold bases.
( 2 )
$771.95
$693.95
Holley EFI ECU terminal crimpers feature adjustable tension settings and a high-quality ratcheting mechanism to ensure every crimp is tight and secure. They're the best crimping tools available for making custom wiring harnesses—and are constructed with a heavy-duty hardened steel frame and molded non-slip hand grips. For fuel injection and engine control projects, arm yourself with a professional-style wire crimping tool.
Not Yet Reviewed
$649.95
On Sale
Precise timing control—Holley EFI dual-sync distributors are built with two Hall effect sensors for crankshaft and camshaft signals. The distributors can be used as just a crankshaft speed input or provide a camshaft sync signal for sequential fueling operation. They're also useful for crank and cam signals when running coil-on-plug applications. Dozens of models are available; order the one recommended for your vehicle/engine application. Some features of Holley EFI dual-sync distributors include: * CNC-machined billet aluminum housings with integrated LEDs for easy setup * Hardened steel distributor gear * Precision-machined shutter wheels that ensure accurate timing—even at very high RPM * Designed to be plug-and-play with Holley systems, but may be used with other EFI systems that support Hall effect crankshaft and camshaft sensors * Housings are available in a variety of finishes
( 37 )
$699.95
$517.95
—
$649.95
On Sale
Do you need to upgrade your ignition system due to a recent Sniper EFI installation, but have no idea which option is best? Introducing Holley Sniper EFI HyperSpark distributors. These billet distributors use a hall-effect crank signal sensor, providing a noise-free RPM signal to the Sniper ECU. HyperSpark distributors include a patented clear installation cap that eliminates any confusion when installing the distributor. They're an easy plug-and play solution to add timing control and complete your Sniper EFI installation. Many options are available; choose the model recommended for your year/make and engine application.
( 127 )
$574.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
