Availability
Aeromotive 1988-97 Chevy Truck Dual 340 in-tank fuel pump modules are direct drop-in units for the specified years of GM 1500/2500 V8 trucks. Featuring dual 340 lph pumps, they can support up to 1,400 FWHP on gas/fuel injection/forced induction and up to 980 FWHP on E-85/fuel injection/forced induction. 100 micron pump pre-filters are included. Additional features: * No drilling required for installation * Individual wiring terminals for each pump to accommodate a staged system * Single -08 ORB outlet port for easy plumbing * Outlet, return, and vent ports include -08 90-degree swivel fittings * Vent port adapter fitting * 0-90 Ohm fuel level sender
Not Yet Reviewed
$725.70
Aeromotive VaporWorx BoostWorx returnless PWM controllers for dual fuel pump applications have everything needed to provide a standalone, OE-type returnless fuel system. They provide a 1:1 manifold referenced fuel pressure using the VaporWorx supplied standalone MAP sensor and mounting bracket, acting just like a mechanical fuel pressure regulator would with the ECM tuned in the same manner. BoostWorx PWM dual-pump controllers feature: * Everything needed electrically to drive the fuel pump module--no relays or Hobb's switches are required * Up to a 2/3 reduction in power to the fuel module during idle and cruise vs. traditional systems * 80-amp minimum continuous power rating in a compact controller package * Over-temperature shutdown with automatic reset * Short circuit protection with automatic reset * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies, where appropriate * All cross-linked polyethylene wiring * UL94 rated components used throughout * Integrates into the OE ECM to allow all safety systems to remain functional * 10 to 22 V operating capacity -- Can be used with voltage boosters -- Lower than 10 V applied to the turn on circuit will cause controller shutdown to protect from an AFR lean condition * Billet aluminum VaporWorx MAP sensor bracket and 3bar pressure sensor * Second pump turn-on set to 4 psi * The PWM controller supports Aeromotive's line of 340 lph in-tank pump
Not Yet Reviewed
$683.25
Aeromotive VaporWorx ReturnX return-type PWM controllers have everything needed to provide a standalone fuel pump speed control system. Available for single or dual pump, naturally aspirated or supercharged applications, no switches, relays, or Hobb's switches are needed when using these ReturnX systems. Controllers have primary and secondary output with the primary providing sufficient pump speed to maintain fuel pressure during idle/cruise while the secondary pump follows at a lower duty cycle. This leader/follower arrangement delivers a smooth ramp-up in pump speed until both pumps are at full output. For carbureted and EFI applications, simply attach the supplied standalone MAP sensor hose to a manifold vacuum source (naturally aspirated) or past the supercharger/turbocharger and make at-idle controller adjustments--the VaporWorx controller will do the rest. Select the single or dual naturally aspirated or supercharged version needed for your setup. Key features: * Works with all brushed-type fuel pumps * Typical power reduction to the pump(s) of 45 to 75 percent * Standalone MAP-based fuel pump speed control * Carburetor and EFI capability Benefits: * Everything needed electrically to drive the fuel pump(s) * A significant reduction in the average fuel pump power requirement resulting in lower fuel temperatures and longer pump life * 40 to 80-amp minimum continuous power rating in a compact controller package * Over-temperature shutdown with automatic reset will operate indefinitely without damage * Short circuit output protection will operate indefinitely without damage * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies * All cross-linked polyethylene wiring * UL94 rated components used throughout * Integrates into the OE ECM to allow all safety systems to remain functional * 10 to 22 V operating range -- Can be used with voltage boosters -- Lower than 10 V applied to the turn-on circuit will cause controller shutdown to protect from an AFR lean condition
( 1 )
$502.90
—
$630.20
Aeromotive Phantom direct-fit fuel pumps are drop-in systems engineered for your late model truck. They're available in five pump sizes, from single 340 lph to triple 450 lph. Designed to work with plastic fuel tanks, Phantom Series pumps cover a range of GM truck models spanning decades. The 1999-2004 models used a smaller factory fuel sending unit than the later 2005-17 models. The smaller size unit limits the pump configurations that this tank will accommodate. Aeromotive Phantom direct-fit fuel pump systems are also compatible with different tank depths.
( 2 )
$755.49
Aeromotive VaporWorx Ally DualX PWM controller kits are compatible with any OEM fuel system control module when using OEM fuel modules with either an OEM Fuel System Control Module (FSCM) or aftermarket ECM pulse driver. They allow the OEM FSCM to control the primary pump while the Ally DualX controller "piggybacks" and takes care of the second. The controller takes its operating commands from the FSCM pulsed wire--no user programming, system changes, or adjustments are needed. In this way, there is sufficient power for all fuel pump modules while maintaining full FSCM CAN feedback and diagnostics. Ally DualX kits perform the following basic functions: * Whenever the primary pump is running, the Ally DualX controller will also be running. This is typically used with OEM fuel pump modules. It is important to have the second fuel pump module running all the time or else it may run dry under some conditions. * Whenever the ECM is providing either a positive or negative pulse, the Ally DualX controller will also be running the primary fuel pump(s). This is typically used with aftermarket ECMs + naked pumps in a mechanically pressure regulated fuel system. Aeromotive VaporWorx Ally DualX PWM controller kits feature: * Everything needed electrically to drive the fuel pump module * Unmatched low fuel level capability when using an OEM fuel module as the second pump * A 1/2 to 2/3 reduction in power to the fuel pump during idle/cruise vs. traditional systems * 40-amp minimum continuous power rating in a compact controller package * Total size 4 in. L x 2.1 in. W x 1 5/8 in. H * Over-temperature shutdown with automatic reset that will operate indefinitely without damage * Short circuit protection with automatic reset that will operate indefinitely without damage * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies where appropriate * All cross-linked polyethylene wiring * UL94 rated components used throughout * 10 to 22 V operating capacity * Can be used with voltage boosters
Not Yet Reviewed
$502.90
Aeromotive VaporWorx Ally Returnless PWM (Pulse Width Modulation) electronics kits for the KPM1500 fuel pump include the necessary parts to modify the KPM1500 (not included) to make it work properly for FSCM (fuel system control module)-equipped vehicles and aftermarket ECM/FSCM systems. The weakness of the OEM FSCM is power capability--they can drive one high-power pump, but not two. That's where VaporWorx Ally PWM kits come in. They provide the components needed to drive the second (KPM1500) fuel pump electrically while the FSCM handles the primary. Using pulse width modulation to slow down the pumps is very effective in keeping fuel temperatures down and relieving the electrical system of excessive load. Ally controllers help reduce the amount of power that the FSCM has at higher fuel demand, so at higher duty cycles the VaporWorx controller will start to out-run the FSCM and take more of the pumping power load. These Aeromotive VaporWorx kits are intended to be used as an Ally, or piggyback, system to help the OEM FSCM. No additional relays, Hobb's switches, etc. are needed.
Not Yet Reviewed
$577.15
Aeromotive continuous duty Eliminator fuel pumps support big horsepower and maintain the driveability necessary for a true high performance street car. Designed for high horsepower street/strip applications, EFI, or carbureted, they feature Aeromotive's "dual chamber" pumping mechanism. The pumps are available in external or in-tank models. Additional features include: * -12 AN O-ring boss inlet port and -10 AN O-ring boss outlet port * Fully submersible for custom in-tank pump placement * 25 percent more flow at pressure than Aeromotive A1000 fuel pump * Supports naturally aspirated EFI engines up to 1,900 hp * Supports forced air induction EFI engines up to 1,400 hp * Supports naturally aspirated carbureted engines up to 2,300 hp * Supports forced air induction carbureted engines up to 1,700 hp
( 2 )
$687.99
Aeromotive Phantom 300 universal diesel fuel pumps offer the classic Phantom design with Aeromotive's cutting-edge fuel delivery technology for the diesel market. Designed for racing applications, the Phantom 300s will ensure the consistent flow you've come to expect, and they are available in single and dual pump models. Choose the one your prefer. Specs and additional features and benefits: * Single pump flow ranges: -- Low range 81.98 gal./hr. at 16 psi, 7 amp, 13.5 V -- High range 37.5 gal./hr. at 100 psi, 14 amp, 13.5 V * Dual pump flow ranges: -- Low range 163.96 gal./hr. at 16 psi, 7 amp, 13.5 V -- High range 75 gal./hr. at 100 psi, 14 amp, 13.5 V * In-tank gerotor pump stays cooler and quieter than an exterior pump * Has a higher flow than most factory lift pumps * Extended bracket length allows for installation in deeper tanks (6 to 20 in.) * 300 micron pre-filter is included
Not Yet Reviewed
$693.35
Aeromotive VaporWorx BoostWorx PWM controllers for DualX ZL1 universal applications simplify installation and increase overall fuel system performance for dual OEM ZL1 fuel module applications. DualX uses a progressive ramping strategy with connections on the controller for the primary (pump 1) and follower (pump 2). The follower pump runs at lower duty cycle than the primary, allowing the follower pump to be on at all times, but at a lower average power, and allowing the pumps in the follower module to continually fill the reservoir with fuel, so it is ready to feed the engine under the most challenging conditions. As the primary pump increases in duty cycle, so does the follower, and once the primary is at 100 percent, the follower continues to increase to 100 percent duty cycle, as needed. This strategy is automatic and requires no user programming or adjustments. BoostWorx PWM DualX ZL1 fuel module controllers feature: * Everything needed electrically to drive the fuel pump module -- No relays, Hobb's switches, or filters needed -- OEM fuel level sensor can be used if desired * Unmatched low fuel level capability * Up to a 2/3 reduction in power to the fuel module during idle and cruise vs. traditional systems * 80-amp minimum continuous power rating in a compact controller package * Over-temperature shutdown with automatic reset * Short circuit protection * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies, where appropriate * All cross-linked polyethylene wiring * Single 20 ft. wiring harness to the fuel module * UL94 rated components used throughout * Integrates into the OE ECM to allow all safety systems to remain functional * Can be used in constant or manifold referenced fuel pressure modes -- Manifold referenced suggested to further reduce electrical demand
Not Yet Reviewed
$630.20
Aeromotive VaporWorx BoostWorx returnless PWM controllers for triple fuel pump applications have everything needed to provide a standalone, OE-type returnless fuel system. They provide a 1:1 manifold referenced fuel pressure using the VaporWorx supplied standalone MAP sensor and mounting bracket, acting just like a mechanical fuel pressure regulator would with the ECM tuned in the same manner. BoostWorx PWM triple-pump controllers feature: * Everything needed electrically to drive the fuel pump module--no relays or Hobb's switches are required * Up to a 2/3 reduction in power to the fuel module during idle and cruise vs. traditional systems * 80-amp minimum continuous power rating in a compact controller package * Over-temperature shutdown with automatic reset * Short circuit protection with automatic reset * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies, where appropriate * All cross-linked polyethylene wiring * UL94 rated components used throughout * Integrates into the OE ECM to allow all safety systems to remain functional * 10 to 22 V operating capacity -- Can be used with voltage boosters -- Lower than 10 V applied to the turn on circuit will cause controller shutdown to protect from an AFR lean condition * Must be used in manifold referenced fuel pressure mode * Billet aluminum VaporWorx MAP sensor bracket and 3bar pressure sensor * Second pump turn-on set to 4 psi * The PWM controller supports Aeromotive's line of 340 lph in-tank pumps
Not Yet Reviewed
$683.25
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
