Availability
Showing In Stock Items. Show All 920 Items.
VS Racing offers a wide range of turbochargers for your horsepower-boosting target. Whether you need greater airflow for racing, some boost for the street, a higher A/R ratio for smoothness, or a low A/R ratio for the drag strip, VS has a turbo to enhance your performance. They're available in dozens of sizes, configurations, and other options.
( 22 )
$379.00
—
$429.00
BD Diesel turbocharger installation kits are available for setting up and servicing your turbo assembly. These gasket and seal kits are required for replacement of individual high-pressure and low-pressure turbochargers.
Not Yet Reviewed
$271.95
Summit Racing™ OE replacement turbochargers are the best choice to replace your worn out, leaking, or failed original equipment units. With more and more vehicles coming turbocharged from the factory, the reality is that most turbos start leaking or the bearings wear out long before the life of the car or truck does and will need to be replaced. We are proud to offer these replacement turbos for various applications, choose the right one for your car or truck. Check out these features and benefits: * 100 percent brand new construction * Direct-fit left and right available * EM spec-cartridge and turbine wheel * OEM spec-housings on brand NEW tooling: tighter tolerances and better finish * Billet compressor wheel with revised and updated Aero: more torque over OEM and OEM replacements * OEM spec rotating assembly for hassle-free operation and longevity * OEM spec oil feed/drain and coolant inlet/outlet: plug-and-play with your existing oil and coolant lines * Increase horsepower, torque, and fuel efficiency over worn OEM turbochargers
( 1 )
$349.99
—
$399.99
FuelTech turbocharger speed sensors are designed to obtain vital data in order to determine whether the turbo is operating within its compressor map and at its highest efficiency. By inputting blade count you can measure rotational speed and maximize your turbo output, thus, allowing you to gain valuable data on turbo selection. Available with or without mating plug kit. Note: This sensor will not read until the turbo speed is above 5,000 rpm, if spinning the wheel by hand, the sensor will read 0 rpm.
Not Yet Reviewed
$399.00
Summit Bucks
ACDelco offers a full line of GM Genuine Parts turbochargers. These stock replacements help to force more air into internal combustion engines, creating more power with each piston stroke. The turbos are crafted from alloy iron to fit each vehicle application. A gasket/seal is included, and no programming is required. Whether you drive a Chevy, Buick, GMC, or Cadillac, there's an OE model ready to restore the power you're missing. Maintain your ride with a GM Genuine Parts turbocharger from ACDelco.
( 2 )
$439.99
Upgrade your factory exhaust feed system with BD Diesel turbo up pipes. These durable replacements are manufactured from stainless steel and they can maximize your turbo response time, as well as eliminate leaks. Smooth mandrel bends and less restrictive, internally shielded expansion bellows (which reduce the chance of burnout) also maximize exhaust energy to drive the turbocharger. Increase exhaust performance with the more efficient, longer lasting BD Diesel turbo up pipes.
( 3 )
$482.95
Pacific Performance Engineering replacement high-flow up-pipes allow as much as 53 percent more flow than stock pipes, and they're a direct bolt-on to your factory manifolds. Diesel engines, even stock, produce high temperatures and pressures. OEM up-pipes eventually fail from constant temperature and pressure fluctuation. Unlike factory parts, these OE replacement high-flow up-pipes are manufactured from 11-gauge 304 stainless steel. They include internally-sleeved bellows that can take the abuse of high temperature and high pressure. Order the model recommended for your application.
( 2 )
$269.99
DEI ONYX Series turbo heat shields fit the popular smaller turbo sizes. They use an exclusive combination of premium heat-resistant textiles and newly designed stainless steel attachment anchors. DEI ONYX shields are used to maintain a more consistent temperature in your turbo, increasing efficiency and decreasing turbo lag. DEI ONYX Series turbo heat shields feature: * Strong riveted anchors to secure shield * Black carbon fiber look * Ultimate thermal barrier reduces turbo lag * Double reinforced seams inside and outside * Direct heat resistance up to 1,800 degrees F * Radiant heat resistance up to 2,500 degrees F
Not Yet Reviewed
$255.99
—
$264.99
Heatshield Products Stealth turbo heat shields can increase boost, reduce turbo chatter or flutter, and help keep your turbo from lagging. By retaining heat inside the shields, your turbo not only becomes more efficient but your underhood temperatures also get reduced, lowering the intake temperatures, and adding power. Heatshield's low-profile black Stealth shields withstand up to 1,800 degrees F (continuous), and their custom design means that no trimming is needed, making installation a snap. Whether you're hardcore racing or in a street machine, heat kills performance—battle back against it with the Stealth turbo heat shields from Heatshield Products best suited for your application!
( 3 )
$264.99
—
$393.99
MBRP turbo up-pipes feature heavy-duty bellows that resist cracking and leaking, which rob your engine of valuable horsepower and torque. Built from aluminized steel, these durable replacement header assemblies are high-heat ceramic coated, and designed to be more durable and reliable than your factory pipes. The stainless steel Turboflex couplings isolate vibration generated by your engine. Ideal for select Powerstroke engine models, MBRP turbo up-pipes are a direct bolt-on installation—delivering more power and an aggressive sound to your truck.
( 2 )
$414.99
—
$549.99
The bar has been raised! These DEI Titanium GEN-3 turbo shields are the most technologically advanced turbo shields ever. DEI has incorporated all of their experience to build the absolute best turbo shields on the market. By developing advanced textiles and diving deep into what is needed to control turbo heat, they developed the Titanium GEN-3 turbo shields. They feature a silicone coated TITANIUM LR outer layer with multiple stainless steel and silica inner layers. Without a doubt the strongest, most heat resistant shields available. DEI Titanium GEN-3 Turbo Shields feature: * Outer shell coated in silicone to insulate and hold up under extreme conditions, helps prevents fraying and encases seams to make them over 4 times stronger * Insulation layer, a thick layer of silica insulation keep heat in turbo shield and turbo housing, providing a low thermal conductivity making one of the best insulators * Inner layer, stainless steel, glass fiber and silicone adds to insulating and thermal properties, increases seam strength, durability and insulation value * Inner cover, stainless steel fabric holds up against the highest temps, will not break down or become brittle with heat * Direct heat resistance of 1,800 degrees F * Radiant heat resistance of 2,500 degrees F
Not Yet Reviewed
$263.99
Funk Motorsports offers turbo heat shields for a wide range of (universal) applications, as well as vehicle-specific models for select BMW, Honda, Ford, and Subaru vehicles from 2002 and up. These turbo and/or turbo wastegate thermal blankets work to insulate the hot side and retain the heat within the exhaust gasses themselves. Hotter gasses accelerate faster, leading to them leaving the system sooner—improving spool up and throttle response. Insulating the turbo also helps to lower the amount of heat that dissipates into the engine bay and intake pipework. A cooler intake results in higher performance and more consistent power figures over time. The 4-layer shields are offered in three finishes: titanium twill, carbon fiber twill, and inside out (for turbos in contact with a heat source). Additional details: * Inside-out blankets have internal material mirrored on the outside, as well * Available for a variety of turbocharger and wastegate styles * A turbo is an absolute furnace within the engine bay. Excess heat produced by the turbo can cause devastation to surrounding sensitive components. Protect anything from oil lines, coolant lines, electronics, and even bodywork positioned close to the turbo from the dangers of excess heat * Funk shields feature specifically developed thread construction to allow for exceptional durability when removal is necessary for routine turbo maintenance. The new fireproof ultra-high temperature stainless steel thread is around 1mm in diameter and can now remain highly durable with temperatures in excess of 1,300 degrees C * New, thicker internal heat lagging insulation provides up to 3x improved heat reduction. This insulation wool is created from a ceramic silica complex matting to improve durability over prolonged heat cycles, as well as insulation quantities * ROHS tested and approved to ensure compliance and desired parameters * NOTE: Turbo blankets are not flammable. However, if any flammable fluids are introduced into close proximity of the blanket, the blanket could become a suitable ignition source for a flame to be produced. Please ensure that all necessary precautions are taken in regard to the appropriate maintenance of all oil and fuel lines and fittings surrounding the turbo charger and fuel injection system. Funk Motorsports takes no responsibility for fluid contamination their products.
( 1 )
$253.13
—
$341.01
Reduce turbo lag while protecting other engine components and help to reduce underhood temperatures with Lava turbo heat shields from Heatshield Products. These custom-fit components use extreme-temperature materials to keep the heat on the hot side of the turbo where it belongs. Installation is a breeze since you don't have to trim or fit the heat shield blanket to fit your turbo housings. Heatshield Products Lava turbo heat shields' silica contact layer and silica insulation make the turbo shields capable of withstanding 1,800 degrees F continuously.
( 9 )
$321.67
—
$378.99
Summit Racing™ turbo hotside fabrication kits give you the pieces you need to get that turbo mounted and fabricate your hotside plumbing from header outlet to turbine inlet flange. Choose kits built for single or twin turbos using T4 or T6 flanges. We include sufficient bends and tubing in 2 1/2 in. 304 stainless to hook up almost anything you can imagine along with open or divided turbine inlet flanges. Advanced fabrication and welding skills required.
Not Yet Reviewed
$285.99
—
$319.99
Mishimoto titanium turbo blankets help reduce the heat in your engine bay. One of the main drawbacks to a turbocharger is the massive amount of heat that it produces, which could lead to cooling issues depending on the placement. With the combination of a volcanic lava rock outer layer and 96 percent silica fiber inner layer, Mishimoto turbo blankets have no trouble keeping the heat from permeating throughout the engine bay. Available in several sizes to fit popular turbochargers, titanium turbo blankets have an interior rating at 1,260 degrees C and can withstand up to 982 degrees C of direct exterior heat. Additional specs: * Rated to 1,800 degrees F direct heat and 2,000 degrees F radiant heat * Interior rated to max temperature of 2,300 degrees F * Available in T25/T28, T3, T4, and T6 sizes * Mishimoto Lifetime Warranty
Not Yet Reviewed
$251.95
—
$284.95
"The most technologically advanced turbo shield ever!" DEI ONYX Gen-3 Series turbo heat shields have been developed using advanced textiles needed to control turbo heat. The outer layer of the shield is coated in silicone to insulate and hold up under extreme conditions, while the inner shield is multiple layers of stainless steel and silica to keep the heat in the turbo shield and turbo housing. The seams are designed for strength, durability, and insulation value. The DEI ONYX Gen-3 Series is available for a variety of applications, find the one that works for you. Features and benefits: * Silicone coating prevents fraying and encases seams to increase strength * Stainless steel, glass fiber, and silicone add to insulating properties * Stainless steel fabric holds up against highest temperatures * Will not break down or become brittle with heat
Not Yet Reviewed
$253.99
—
$295.99
If you hear excessive whistling noises or believe your stock turbo is damaged, you need Standard Motor stock replacement new turbochargers. These 100 percent new units are designed for a direct-fit installation into specific gasoline or diesel applications. They come ready to roll with high-grade materials and complete gasket kits to ease installation.
( 1 )
$433.99
—
$443.99
Clearance
Cardone new turbochargers assemblies meet the growing demand for maximum vehicle performance with optimal fuel efficiency. Every Cardone turbocharger has been designed and tested to guarantee Original Equipment fit and performance. Get your vehicle back to peak performance with new, direct-replacement turbochargers from Cardone. Turbocharger features: * 100 percent dynamic balancing of compressor wheels, turbine shaft/wheel assemblies and complete rotating assembly guarantees proper operation and extends unit life * Unit comes with the required gaskets and mounting hardware for easy installation * Meets or exceeds OE performance * Unit comes with a pre-lube syringe to ensure product protection during installation * Manufactured with 100 percent new components and tested to ensure trouble-free operation
Not Yet Reviewed
$781.99
$499.50
Canton Racing accusump turbo after oilers are designed to solve the main cause of turbo wear and failure by supplying a pressurized discharge of oil to the hot turbo bearings during turbo spool-down. This oil will lubricate and cool the bearings and prevent coke buildup (which limits oil flow). The oilers are manufactured with the same design features and to the same high standards as all Canton Racing accusumps. A piston separates the oil side from the air pressure side, which allows them to be mounted in any position and permits an air precharge. With a precharge, all of the oil is discharged under pressure for positive oiling, and no oil is diverted from the engine until pressure is established on restart.
Not Yet Reviewed
$319.00
—
$348.00
BorgWarner turbine housings are perfect homes for your turbo to live in. Engineered and built from cast iron with external wastegates, BorgWarner offers a wide variety of inlet flange styles, volute types, and A/R ratios to give your turbine the power to perform. Help your vehicle meet your performance goals; order the BorgWarner turbine housing designed for your turbocharger model.
Not Yet Reviewed
$398.99
BD Diesel turbo blankets keep your engine compartment cooler—and cooler temperatures can result in higher density, that results in more power. Plus, decreased temperatures will help to increase the life of hoses, harnesses, and coolant bottle. BD Diesel turbo blankets are available in several sizes to create a custom fit. Features include: * Retains and normalizes internal turbine housing temperatures for lower spool times * Custom fit for Borg Warner T3 S300 wastegated, T4 S300/S400, and T6 S400/S500 * Also fits most similar size Garrett and Holset turbo applications * Comes with stainless steel springs and built-in retaining clips for a seamless install * Stylized look with custom BD embroidery
Not Yet Reviewed
$272.95
Custom-fit DEI Titanium turbo shields provide the ultimate means of reducing turbo lag, while serving as superior heat barriers. They shield and protect engine components, hoods, and painted surfaces and offer a very cool carbon fiber look. Made from pulverized volcanic rock and then strained into a fiber material, Titanium turbo shields can withstand direct heat up to 1,800 degrees F and radiant heat up to 2,500 degrees F. This means retaining more heat in the turbine and less damaging underhood heat. The results are a cooler air intake temperature and a boost in horsepower! Stronger and more durable than other turbo blankets or shields, DEI Titanium turbo shields include high-temperature rated silica insulation padding under a tight outer layer for extra-added protection against extreme turbo-generated heat.
( 5 )
$256.99
Thermo-Tec Rogue Series turbo cover kits provides an easy-fit design that keeps the turbine spooled up, reducing turbo lag. The covers feature dual layer construction to increase durability, reduce underhood temperatures, and improve horsepower, as well as performance by maintaining temperatures inside the turbo. Thermo-Tec Rogue turbo kits include cover, a 2 in. x 25 ft. roll of Rogue exhaust wrap, 18 in. snap straps, and 10 ft. of wire for easy installation.
( 1 )
$255.59
Clearance
Pure Energy new turbochargers are engineered and built for performance, efficiency, and power. Assembled to the highest quality standards, their new turbochargers go through strict test and evaluation processes to assure proper performance and reliability standards are met. Pure Energy turbochargers are supported by a free tech support hotline, staffed by ASE certified master technicians with access to extensive vehicle-specific repair data. Quality enhancements include: * Precise dual plane balancing of turbine shaft and compressor wheel eliminates high-speed vibrations, premature shaft and bushing/bearing failures, and assures quick spool up * New OEM design or upgraded CHRA (Center Housing Rotating Assembly) internal components assure reliability and durability * Thrust plates, seating rings, and journal bearings are strategically designed to withstand internal oil pressure and improve lubrication
( 2 )
$482.99
$397.50
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
