Availability
Showing In Stock Items. Show All 32 Items.
On Sale
MSD ignition controls are the most successful aftermarket ignitions ever made. The multiple spark design has won races and championships in every type of motorsport. MSD ignitions are consistent, reliable and durable, even under extremely harsh conditions. The results speak for themselves--more power, easier starting, quicker throttle response, smooth idle, and improved fuel consumption.
( 37 )
$549.95
$493.95
On Sale
Change your vehicle's ignition timing without leaving the driver's seat with one of these MSD adjustable timing controls. They're designed to fit virtually all vehicles with a 12 V negative-ground ignition, a distributor, and an externally mounted coil. They feature a knob that mounts to the dash for easy and accurate timing adjustments, allowing you to adjust timing up to 15 degrees to compensate for bad gas, altitude changes, and heavy loads.
( 18 )
$299.95
$269.95
On Sale
aFe Control suspension logic ESD kits contain simple plug-and-play modules that eliminate the suspension control check engine light. This allows installation of aftermarket shocks or coilovers on vehicles previously equipped with electronic shock absorbers. ESD (electronic shock delete) kits are sold in sets of four, one for each shock, and feature anodized extruded aluminum heat sinks, abrasion-resistant braided wiring shields, and GM-style Metri-Pack connectors.
( 1 )
$372.00
—
$433.00
$334.80
—
$389.70
On Sale
As LS engines make their way onto the race track MSD is ready with the Circle Track LS ignition controls. You're off to the races with MSD. Circle Track LS ignition controls feature: * Direct plug-in to factory GM LS sensors and coils * Preprogrammed to run the GM CT525 crate engine out of the box * Laptop programmable rpm limit, timing curve, and coil selection for custom tuning * Auto detects coils, cam sensor, and crank sensor * Will run 24x 1x, 58x 1x, and 58x 4x crank/cam sensor combinations * Self-powered with USB for laptop programming * Steady, accurate timing control * Dedicated plug for Tech Official
Not Yet Reviewed
$549.95
$493.95
On Sale
MSD digital multi-retard timing controls provide four different stages of retard, along with an adjustable start retard feature--with no modules! These units use a high-speed RISC micro-controller to direct the timing functions. This controller can make extremely quick compensations to the timing, while maintaining accuracy to within 1 degree. These circuits are thoroughly de-bounced and isolated for protection against Electro Magnetic Interference (EMI). There is also an innovative magnetic pickup compensation circuit built-in to allow for rock-steady timing with a variety of different mag pickups. There are four separate retard stages that can be activated independently or together for a total sum of retards. Each stage is adjustable from 0-9 degrees, and a maximum of 20 degrees of retard can be pulled out. On top of these great features, there is also an optional start retard circuit that can be programmed to retard the timing 5, 10, 15, or 20 degrees during cranking. Digital multi-retard timing controls can be used on 4, 6, or 8-cylinder engines, and must be used with an MSD ignition control.
( 2 )
$499.95
$274.95
On Sale
MSD Power Grid system controllers are the brains behind the entire Power Grid system, and they can be used with any MSD ignition or Pro Mag to provide advanced ignition tuning capabilities. While they're compatible with all MSD ignition boxes, they've been specially designed to mount on top of the Power Grid 7 ignition box. Features include: * USB connection for easy programming * Timing based on engine rpm and gear value * Advanced individual cylinder timing based on gear or time * Five retard stages for nitrous * Four steps of rpm limits for burnout, spool, launch, and overrev * Output switch set on rpm, pressure, or time * Shift light settings for each gear * Ignition data acquisition accepts multiple runs * View software * Wiring harness * Micro SD-card
( 10 )
$368.95
$332.05
On Sale
aFe Control Suspension Logic ESD modules will allow you to take your truck to the next level of off-road performance. When you're ready to upgrade with aftermarket shocks, such as aFe's Sway-A-Way 3.0 shocks, their Electronic Shock Delete (ESD) modules ensure a seamless install without triggering any error codes. You'll retain full access to all drive modes, including BAJA mode with its dynamic engine calibrations and off-road-tailored system tuning. Even if you plan on retaining the electronic shock system, having this module on hand during your off-road adventures will provide invaluable peace of mind. If a shock becomes damaged, or an electrical sensor is compromised, your truck may enter a faulted state, and leave your truck in reduced power mode. If this happens, you can quickly resolve the issue by plugging in aFe's ESD module, instantly restoring your truck's full functionality. aFe Control Suspension Logic ESD modules are quick and simple, plug-and-play upgrades that allow you to experience the full potential of your truck.
Not Yet Reviewed
$350.00
$315.00
On Sale
Get on the performance grid with MSD Ignition Power Grid power modules. When connected to the Power Grid, they will data log all the functions--including time from launch and time or rpm of activation and deactivation. These timing controllers feature four high-current, solid-state switches that can be configured independently or in conjunction by time, rpm, and temperature switching on/off, as well as by percentage for nitrous systems. Each channel is capable of handling 20 amps of current without the use of a relay and can be used to activate fan, fuel pump, nitrous oxide system, throttle stop, and more--the possibilities are endless.
( 1 )
$749.95
$412.95
On Sale
AEM 22-channel CAN sensor modules provide a way for users with carbureted vehicles to add an AEM CD digital dash display. They also let users with existing CAN-based devices add more channels to the display for viewing and/or data logging. These 22-channel modules convert analog, digital, and frequency inputs into an AEMnet CAN bus signal that can be transmitted to AEM's CD-5 carbon and CD-7 digital dashes. AEM Electronics 22-channel CAN sensor module includes: * Wiring harness with 36 in. flying leads and pre-wired CAN cable * IP65-rated enclosure is dust-tight and water-resistant * Daisy-chain two modules together for additional channels (modules sold individually) * Four dedicated 0-5 V analog inputs * Four temperature (thermistor) inputs * Four user-configurable inputs for 0-5 V, temp (including RTD) * One dedicated fuel level input (0 to 250 ohm range) * Six digital inputs, active low, protected to about 18 V, frequency, duty cycle or simple switch * One tach input, trigger when low, 12 V internal pull up * Two VR pair frequency inputs (crank, wheel, or driveshaft speeds) * Jumper selectable CAN bus speeds, 250k, 500k, 1M * Jumper selectable terminating resistor * Jumper selectable header length, 11 bit or 29 bit
Not Yet Reviewed
$413.95
$371.95
On Sale
You have an alternative choice for flex fuel sensors--AEM Electronics ethanol content sensors. While most gas stations label their flex fuel as E85 (85 percent ethanol/15 percent gasoline), the actual content could be quite different. AEM sensors deliver the ability to determine the composition of the fuel blend pumped into your vehicle at any given time. They measure content percentage and fuel temperature allowing users with programmable engine management systems (capable of tuning for flex fuel) the ability to optimize their engine's tuning calibration for fuel ethanol content. These kits include plug and pins for electrical connections, as well as either -6AN or hose barb fittings (depending on kit chosen) for integration into the fuel system.
( 4 )
$328.95
$296.05
On Sale
AEM exhaust backpressure install kits are specifically designed to give accurate backpressure readings, without sacrificing sensor longevity due to extreme operating conditions. Designed for use with their 4-channel wideband UEGO controller, you get precision readings for ultimate performance using AEM exhaust backpressure install kits. Kits include: * Stainless steel 100 psig pressure sensor * Stainless steel standoff tube with fittings * Stainless steel braided hose * Weld-on/threaded bung.
( 1 )
$368.95
$332.05
On Sale
MSD Pro-Billet Ready-to-Run EFI distributors are the perfect upgrade when you start making serious power with your EFI Ford or Chevy. They use a stock-style trigger pickup and come with plug-in connectors. Installation is simple by removing the stock distributor, then plugging in and bolting the new one in place! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. These distributors will smooth out the engine's idle, improve starting, and perform at a much higher rpm. Their housings are machined from billet aluminum, using state-of-the-art CNC mills and lathes. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing for accuracy through the entire rpm range. Chevy models also feature an extra-long sintered bushing at the bottom and an extra oil tract machined into the bottom of the housing for improved lubrication. The tract delivers oil directly to the cam and distributor gears. All of the shafts receive a QPQ coating for low friction wear, and resistance against corrosion from humidity and ozone buildup. The Chevrolet models have also been tested by the Underwriter's Laboratory, and are certified to meet or exceed safety standards for marine ignition systems as set by the U.S. Coast Guard.
( 93 )
$499.95
—
$549.95
$448.95
—
$493.95
On Sale
MSD Digital 6 off-road ignition controllers deliver a fully potted design that provides the ruggedness and reliability needed to get your 4WD to any destination. These units multi-spark below 3,000 rpm on V8s—ensuring clean, crisp throttle response and complete fuel burn when crawling at low speeds. Above 3,000 rpm, a powerful capacitive discharge spark keeps the fire lit until you let off the skinny pedal. The smooth, accurate rev-limiter will protect your engine from over-rev damage due to drivetrain failure or a slick spot on the trail. Whether you're crawling rocks, high-speed desert racing, or playing in any kind of harsh terrain, your off-road rig can benefit from an MSD Digital 6 off-road ignition controller. Features include: * MSD's smoothest rev limiter yet! Easy on your engine * Fully potted design provides reliability even in high-vibration and wet circumstances * Large, easy-to-read LED display * Simple setup of features, such as the rev limiter, with three rotary dials on the face of the unit * Built-in Start Retard adjustable in 0, 10, or 20 degree increments for quick, easy starts and extended starter life * LED displays rev limit, highest RPM turned, cylinder select, start retard, battery voltage, and can be set to tach mode * Full delivery of spark energy down to 6 V battery supply * Highly efficient, low-current draw for extended battery life * Rugged housing to stand up to demanding off-road and race conditions * Single plug-in connector for clean wiring * Works on 4, 6, and 8-cylinder engines * Reverse polarity and overheat protection provide ultimate reliability
( 7 )
$549.95
$493.95
On Sale
Replace the weak link in your LT1 ignition with these ACCEL Performance Replacement GM Opti-Spark II distributors. They feature an all-new construction with heavy-duty Oil-lite bushings and polished aluminum housings. The ACCEL Performance Replacement GM Opti-Spark II distributors include a high dielectric strength reinforced cap with brass contacts and a balanced rotor. Also included are new pin drive shaft seals, hardware, and easy-to-follow instructions.
( 16 )
$472.95
$424.95
On Sale
These MSD 6TN and 6ALN ignitions are the ultimate choices for superior performance in harsh racing conditions. With sturdy vibration mounts and CD circuits encased in a clear 2-part silicone elastomer, they are virtually vibration-proof. A specially designed, weathertight, 6-pin connector meets NASCAR's 20-6.1 ignition wiring rule and provides a tight, positive-locking connection with individual seals to keep dirt and moisture from each connection. The 6TNs are equipped with a special 4-pin connector that plugs directly into an MSD soft touch rev control, while the 6ALNs have a built-in rev control. These rev controls are adjustable with plug-in modules and will save your engine from overrev damage caused by missed shifts or driveline failures. They'll work with virtually any 4, 6 (even-fire V6 only), or 8-cylinder engines.
( 6 )
$522.95
$469.95
On Sale
MSD Street Fire EFI distributors are ready to drop in your V8 engine and replace the worn-out OEM piece. They feature a factory-style ignition module, along with a durable new cap and rotor. The distributors use a cast housing, making them more affordable, but are much stronger than standard OEM distributors. The MSD Street Fire EFI distributors are available for both Ford and Chevy EFI engines.
( 26 )
$381.95
$343.75
On Sale
MSD Digital 6CT ignition controllers are hardcore ignitions that work as hard as you do at the track. Their superior design is packed with a slew of features, including a large, easy-to-read LED display and a simple setup utilizing three rotatory dials. MSD Digital 6CT ignition controllers offer the smoothest performance ever that comes in a fully potted, tamper-proof housing that uses a single connector to keep wiring tidy. MSD Digital 6CT ignition controllers feature: * Built-in start retard adjustable in 0, 10, or 20-degree increments for quick, easy starts and extended starter life * LED displays rev limit, highest rpm turned, cylinder select, start retard, battery voltage, and can be set to tach mode * Full delivery of spark energy down to 6 V battery supply * Highly efficient, low-current draw for extended battery life * Single plug-in connector for clean wiring * Tamper-proof screws to prevent modification of unit * Records highest rpm the engine turned for last 20 minutes of run time * Works on 4, 6, and 8-cylinder engines * Reverse polarity and overheat protection provide ultimate reliability
( 4 )
$499.95
—
$549.95
$448.95
—
$493.95
On Sale
MSD Pro-Billet Ready-to-Run distributors are the perfect upgrade for weak OE electronic distributors, outdated points distributors, and large HEIs or DuraSparks. All that's required is to install the distributor in the engine, and connect three wires and the coil! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. It will smooth out the engine's idle, improve starting, and perform at a much higher rpm. The housing is machined from billet 6061-T6 aluminum, using state-of-the-art CNC mills and lathes for a unit with no porosity or weak areas. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing, while an extra-long sintered bushing guides the shaft at the base of the housing. This shaft also receives a QPQ coating for low friction wear and resistance against corrosion from humidity and ozone buildup. The distributors feature MSD's adjustable mechanical advance, which allows you to custom-tailor an ignition curve to match your engine's needs. Most models are also available with a vacuum advance canister to help improve economy. Order the model recommended for your vehicle and engine application.
( 329 )
$499.95
—
$649.95
$357.95
—
$493.95
On Sale
Pertronix Flame-Thrower stock look cast distributors are loaded with all of the features that you would expect from a high performance part, and yet they maintain the original look, for the ultimate "sleeper." Pertronix builds each distributor with all-new components, not from remanufactured parts like some companies do. No longer will you need to hassle with adjusting points or replacing capacitors, because these distributors are equipped with maintenance-free Ignitor electronics, providing decades of trouble-free operation. Each distributor is complete with a high-quality cap and rotor, so you're ready to run right out of the box. Stock look distributor features include: * All-new lightweight cast aluminum housing, modeled after the original Delco and Motorcraft distributors * Hardened gear ground to exact tolerances for precise mesh with cam * Adjustable vacuum advance canister, providing extra tunability * Optimized phasing to ensure maximum energy to the spark plug * Tailored advance curve for optimal performance and drivability * Integrated electronic ignition--available with solid-state Ignitor or the powerful Ignitor III with built-in adjustable REV limiter and multi-spark through redline * High dielectric strength cap and rotor with brass contacts
( 255 )
$318.80
—
$398.40
$286.92
—
$358.56
On Sale
PerTronix Flame-Thrower plug and play billet distributors with Ignitor II® module are designed to provide maximum ignition performance and easy installation, all at a price that you can afford. They allow you to upgrade your outdated points or stock electronic distributor with a performance-proven unit. The distributors feature the patented Ignitor II® electronic ignition module and a CNC-machined 6061 T-6 polished billet housing. PerTronix electronics are compatible with any inductive ignition system coil, but high-rpm performance can be improved when they are used with the low-resistance (0.6 ohm) Flame-Thrower II coil. Their stand-alone design makes them plug-in units that require no additional ignition, but they are compatible with multi-spark CD ignition boxes for outstanding versatility. Additional features include a tempered shaft, an upper roller bearing, and an oil-impregnated sintered bronze lower bushing. The PerTronix Flame-Thrower plug and play billet distributors with Ignitor II® module come with a factory-set performance curve, a mechanical advance limiting adjustment, and a small, high-dielectric strength cap and rotor for applications with little clearance.
( 358 )
$387.25
—
$418.00
$348.52
—
$376.20
On Sale
MSD 8.5mm Super Conductor spark plug wire sets feature a special helically wound core that has just 40-50 ohms of resistance per foot—but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire includes 40 ft. of tightly wound copper for superior conductivity. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference "choke." This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Each set comes with clip-on cylinder markers for easy identification. MSD's 8.5mm Super Conductor wire sets are available in custom or universal-fit applications, assembled or not, with a variety of terminal and boot end options.
( 1972 )
$283.95
—
$699.95
$255.55
—
$454.95
On Sale
PerTronix Flame-Thrower plug and play billet distributors with Ignitor III® module offer the latest version of Pertronix's ignition modules. They include the patented Ignitor III® electronic ignition module and a CNC-machined 6061 T-6 polished billet housing. The Ignitor III® features adaptive dwell, which maintains peak energy throughout the entire rpm range, reduces misfires and improves engine performance. Peak current level is reached just prior to spark for maximum energy without the heat buildup and increased coil performance and module reliability. They adjust spark timing at higher rpm to compensate for the inherent electronic delay and increase energy for quicker, easier starting by sensing startup. The PerTronix Flame-Thrower plug and play billet distributors with Ignitor III® module have an integrated digital rev limiter with LED feedback for precise RPM setting and a memory safe function that stores settings eliminating unintended changes to the rev limit.
( 138 )
$438.15
—
$448.75
$394.34
—
$403.88
On Sale
PerTronix Flame-Thrower billet plug and play marine distributors feature the Ignitor II® electronic ignition module, a billet CNC-machined housing, an upper roller bearing, and a self-lubricating, oil-impregnated copper powder metal lower bushing. They are compatible with any inductive ignition system coil and come with a factory-preset performance curve, a mechanical advance limiting adjustment, and a small-diameter, high-dielectric strength cap and rotor.
( 80 )
$418.00
$376.20
On Sale
Choose EFI main power wiring harnesses from Holley to meet your needs. Several choices are offered—TBI, LS applications, multi-point, and un-terminated harnesses—to feed and carry your engine's electrical supply. Get wired for electronic fuel injection with Holley EFI systems main wiring harnesses.
Not Yet Reviewed
$549.95
$493.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
