Free Shipping on Orders Over $125 at Summit Racing

Cold Case Radiator Support Module Kits

Cold Case offers radiator support module kits for a variety of applications, including 1960s era Camaro LS engine swaps. Each module comes fully assembled and ready to bolt into your vehicle. They consist of an aluminum radiator support, big 1.25 in. tube dual-core crossflow radiator, two 3600 cfm fans/shroud combination, billet cap, and billet overflow tank. These units are very popular with high-tech, high horsepower builds in which maximum cooling is a must. Available in either standard Chevrolet outlet configurations or LS outlet configurations, they're 100 percent TIG-welded and ready to paint or polish. Radiator support module features: * Extra forward design will clear big block and LS front drives * Brushed aluminum finish * 2 row design with 1.25" tubes * Includes dual 14 in. 3600 cfm fans and shroud combination setup * Easy to install even in finished cars * Optional AC condenser and electronic fan controller upgrades available

2.2 out of 5 stars ( 5 )

$2,289.54

—

$2,671.54

On Sale

Holley Sniper 2 EFI 650 HP Inline Pump Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Inline Pump Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters for before and after the pump, fittings and hardware, cushioned mounting brackets, and an external, inline pump * Can be used with 3/8 in. factory sending units or add a dedicated bulkhead fitting * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

4.33 out of 5 stars ( 21 )

$2,399.95

—

$2,609.95

$2,158.95

—

$2,347.95

On Sale

Holley EFI Digital Pro Dash Standalone Kits

Upgrade to Holley EFI Standalone Digital Pro Dash kits and get the facts on your engine! They offer two versions--both are full of features that support most any users, install almost anywhere, and just like traditional gauges install in almost anything. Holley's 6.86 in version actually measures 3.5 in. tall x 7.6 in. wide, is easily mounted in a console/dashboard, off a roll cage, or on a steering column, and includes a 10 LED shift light. The larger 12.3 in. version is for hard-core enthusiasts who want the ultimate display device, and measures 11.5 in. wide x 4.25 in. tall. Holley EFI Standalone Pro Dash units feature: * Standalone digital dashes--no ECU or fuel injection required * High resolution, state-of-the-art, multi-gauge touch screen display with fully configurable layouts: -- Full color, capacitive touch screen with auto dimming for crystal clear data--day or night -- Quickly swipe between multiple active screens (tune, warm-up, race, drive, etc.) -- Virtual switch panel eliminates the need for external toggle switches -- 16 default background skins pre-loaded with unlimited options for importing custom layouts -- Built-in GPS with speed, odometer and trip odometer function (external antenna included) -- Rendered analog (dials/needles) and digital gauge styles available -- Integrated datalogger -- Rugged, water-resistant case constructed of cast aluminum for long life and durability * Plug-and-play features are pre-configured in the harness and include dash layouts/screens for: -- Oil and fuel pressure, coolant and air temperature (utilizes plug-and-play Holley sensors, not included) -- Turn signals, high beam, fuel level, engine vacuum/boost * Additional input and output functionality: -- 13 multi-configurable inputs -- 4 ground switched outputs -- 4 speed channels (two dedicated) for rpm, driveshaft speed, or any other Hall effect speed input -- User definable channel alarms and warnings * Communications/harness: -- 4-pin wiring harness contains power, ground, and CANbus connections -- Holley EFI CANbus connection for expanded capability with Holley EFI systems -- Expandable storage via USB * Integrated datalogger: -- Internal log memory of 1GB (expandable up to 32GB with addition of micro-SD card) -- External logging to USB flash drive is also available for easy file management -- On-screen datalog playback allows you to review vital run information right on the dash -- Full analysis via laptop is available. Simply download the file to a USB drive and view with the free datalog viewer at Holley.com * Flexible mounting options: Surface or flush mounting—high-quality hardware included * Simple setup and programming: USB keyboard and mouse functionality * Fully upgradeable * Both dash versions include harness/cables, mounting hardware, USB memory stick, and CAN terminator * GPS antenna * Sensors not included

5.0 out of 5 stars ( 3 )

$2,299.95

$2,068.95

Ford Performance Parts Boss 302 Engine Blocks

The perfect foundation for your Boss engine--Ford Performance Parts Boss 302 engine blocks! They're built stronger than the originals to make your high performance build a success. Designed as replacements for the legendary Boss 302 and Boss 351 blocks, they use the latest technology and manufacturing techniques. Cast from diesel-grade iron with siamesed bores, thick cylinder walls and decks, Boss block strength is far superior to any Ford production block. Boss 302 blocks are available in standard and Big Bore versions that support engine sizes up to 363 c.i.d. Proven around the world, both on the track and on the street; all Ford Performance Boss 302 blocks are cast and machined to the highest industry standards in the USA. Features include: * Big Bore version features 4.125 in. bore capacity, finished at 4.115 in. rough bore * Standard bore version is finished at 3.990 to 3.995 in. rough bore with 4.125 in. bore capacity * 8.2 in. deck height, finished at 8.200 in. plus .010 to .015 in. * Optimized cylinder wall length for stroker applications up to 3.5 in. with no grinding or clearancing (depends on crank/rod manufacturer) * Splayed 4-bolt mains on 2, 3, 4, main caps * 2-bolt main on first and fifth main caps * Main bearing bores finished to low limit * Finished lifter bores * Machined to accept factory roller lifter guides and lifter guide retainer * Fits factory 1979-95 Mustang oil pan with custom oil pickup tube, part number: M-6622-BOSS302 * NASCAR inspired front oil feed on both lifter galleys * Revised cooling system passageways * Increased bulkhead material * Threaded core and galley plugs (straight thread port plugs with O-ring) * Require special length 1/2 in. head bolts M-6065-BOSS or head studs M-6014-BOSS recommended with M-6049-X306/307/Z304DA heads * Designed for M-6049-X306//X307/C3/D3/Z304DA cylinder heads * Not designed for production 302/351W or M-6049-Y302/Y303/X302/X303/X304/X305 cylinder heads * Uses common O.D. cam bearings M-6261-J351/R351 * Unique cam plug M-6026-S351 included * M-6051-S331 or M-6051-CP331 head gasket recommended * Uses stock-type timing cover (M-6059-D351 recommended; includes fuel pump provision) * Retains clutch cross shaft pivot hole * Original-style oil filter location * Original motor mount boss locations * Original bell housing pattern * Approximate weights: Big Bore 163 lbs.; standard bore 175 lbs.

5.0 out of 5 stars ( 3 )

$2,265.99

On Sale

Holley Sniper 2 EFI 650 HP Returnless Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Returnless Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters before/after the pump, fittings/hardware, and a low profile returnless drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Pre-set, internally regulated pump only requires a single feed line to the Sniper 2 unit * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

4.0 out of 5 stars ( 2 )

$2,249.95

$2,023.95

On Sale

Holley Sniper 2 EFI 650 HP Return-Type Fuel Injection Systems with Power Distribution Module

Holley Sniper 2 EFI Return-Type Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, return line, external regulator, filters before/after the pump, fittings/hardware, and a low profile return-type drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected

Not Yet Reviewed

$2,249.95

$2,023.95

APR Intercooler Systems

APR intercooler systems result in repeatable performance—even in the most demanding of situations. These massive front-mounted upgrades dramatically reduce intake air temperature (IAT), minimize heat soak, and provide increased performance in easy-to-install, direct bolt-on designs. The superior effectiveness and performance of APR systems is focused around core selection, end tank design, and specific install location for each application. Balancing all the necessary characteristics, APR's engineers perfected units with exceptional cooling and lowered pressure loss across the core, while maintaining critical airflow to components behind the system—delivering maximum performance and far exceeding the capabilities of factory intercoolers. Features may include: * Aluminum construction * Large bar-and-plate design with densely packed staggered and louvered fins * Smooth cast aluminum end tanks engineered for low turbulence/restriction and maximum flow * Pressure tested to prevent power robbing boost leaks * Full directions and APR world-renowned customer support * Some systems may include CNC-bent and TIG-welded mounting brackets, high-quality multi-ply silicone inlet and outlet hoses, T-bolt clamps, and billet MAP sensor housings

Not Yet Reviewed

$2,254.95

Roush 2011-14 5.0L F-150 Phase 2 Replacement Supercharger Fuel Charging Assemblies

Roush 2011-14 5.0L F-150 Phase 2 replacement supercharger fuel charging assemblies are key components of the Phase 2 supercharger kit (P/N 421435), designed to boost the 5.0L Coyote V8 engine by replacing the stock intake manifold with a high-efficiency TVS2300 unit. These assemblies include the upper/lower intake manifolds, fuel injectors, rails, and a 60mm twin throttle body, delivering up to 727 hp. Key components and details: * Supercharger unit: Features the R2300 TVS (Twin Vortices Series) 2.3L roots-type positive displacement blower * Intake manifold: Redesigned upper and lower aluminum manifolds designed for increased airflow * Fuel system: Includes upgraded high-flow fuel injectors to support the increased power demands of the Phase 2, which offers more power than the Phase 1 * Throttle body: Twin 60mm throttle body with a matching spacer to maximize air intake * Performance: Designed to work with the Phase 2 calibration to provide significant power gains (appx. 210 hp and 150 lbs.-ft. over stock). * This assembly serves as the core, top-end replacement component for upgrading the 2011-14 F-150 5.0L to higher performance levels, often referred to as the "blower" or "supercharger top-end" in the kit.

Not Yet Reviewed

$2,127.00

APR DTR6054 Turbocharger Systems

APR DTR6054 turbocharger systems are direct replacements for the EA888 Gen 3 engine. These upgrades include matching software for various vehicles and mods, providing up to 491 hp and 425 lbs.-ft. of torque, depending on vehicle platform and fueling, all while keeping emissions components unmodified. The software supports premium pump fuel grades, race fuel grades, and even ethanol on the Golf R, S3, and TT S platform with fueling upgrades. For dedicated race cars the turbocharger is designed with plenty of headroom to go even further on your own! Designed and developed from the ground up by APR, DTR6054 turbochargers do not require a core and there's no additional downtime. They are built using an aluminum anti-surge compressor cover with appropriate A/R matched to a larger aircraft-grade, 6061 billet aluminum 60mm compressor wheel, a turbine housing cast with high-temperature 310 stainless steel to take the heat and abuse seen on a road course, and a nickel-based superalloy K418 high-flow 54mm turbine wheel. A German dual ceramic ball bearing center section provides smooth and reliable operation with a better transient response, eliminating the factory failure-prone journal bearing design. Each kit includes the complete turbocharger with compressor inlet pipe, compressor outlet hose, T-bolt clamps, gaskets, O-rings, exhaust ring, exhaust V-band, exhaust manifold gasket, studs, bolts, and washers, oil and coolant line O-rings, and APR's ECU upgrades for select vehicles. The upgrade uses your factory electronic wastegate and diverter valve, and connects to your factory exhaust, intake, turbo outlet pipe, and oil and coolant lines. Tested at various road courses, APR's DTR6054 turbocharger systems do not spike torque hard or run on the edge of what the factory rods and pistons have been known to handle, making them as safe on the stock engine as possible for these power levels. Additional features: * Over 30 percent compressor flow compared to the factory turbocharger * Various software levels depending on fueling modifications, including stock fueling * Supports 91, 93, 100, and 104 AKI in all configurations * Supports E60-E85 with fueling upgrades (Golf R/S3/TT S platform only) * VSR balanced turbocharger center housing rotating assembly (CHRA) for reliable operation * Oversized cast turbo inlet pipe connects directly to factory or upgraded intake system * Machined turbocharger speed sensor port with included billet block-off plug * Silicone discharge hose with APR EZ-flow stepped lips included (no turbo muffler) * Integrated diverter valve (DV) port * Available in turbo kit only, turbo kit with low- and high-pressure fuel pump, or turbo kit with low- and high-pressure fuel pump and multi-port injection

Not Yet Reviewed

$3,499.95

—

$4,816.95

Be Cool Extreme Modules

Be Cool Extreme modules offer show-stopping looks and performance for your resto classic! If you want more bling than Be Cool Show & Go modules, their Extreme radiators provide the ultimate in American-made brilliance. They're available in a natural aluminum finish, or in show-polished assemblies with every component chromed or polished—to deliver extreme looks to your special ride. And their performance is, of course, super-cool! Be Cool Extreme module features: * Performance-grade dual 1 in. core polished radiator * Chrome plated high-torque fans with billet Extreme logo motor covers * Stainless steel electric and/or aluminum fan mounting brackets * Diamond-cut aluminum vented coolant recovery tank with Extreme logo * Machined aluminum Sure-Grip radiator cap with embossed emblem * Wiring harness with temperature control sending unit and 40 amp relays * Various radiator style options, including crossflow and downflow

4.0 out of 5 stars ( 7 )

$3,799.99

—

$4,499.99

Be Cool Show & Go Modules

It's show time! Be Cool Show & Go modules will wow the judges with their mirror-like finish. Not only do these modules look show-car great, but their cooling performance will receive top honors as well! These power-cooling modules come with all you need to add stunning performance and appeal to your custom engine compartment. Pop your hood and let everyone appreciate the ultimate expression of cooling technology--the brilliance of American-made Be Cool Show & Go modules! Be Cool Show & Go cooling modules feature: * Polished performance-grade dual 1 in. core radiator * Black fans with billet Be Cool logo motor covers * Fan mounting brackets and hardware * Polished aluminum vented recovery tank * Polished billet aluminum radiator cap with Be Cool logo * Wiring harness with temperature control sending unit and relays

4.75 out of 5 stars ( 8 )

$3,699.99

—

$4,364.99

11 Results Found For "core support"