Availability
Showing In Stock Items. Show All 36 Items.
MSD puts their years of experience to work in making these top-notch iron camshaft mounted distributor gears. Their high-grade ductile iron is micro-polished for a smooth and scuff-free finish, and then Melonite QPC coated to reduce friction and initial wear. Excessive clearance causes timing fluctuation throughout the rpm range, resulting in lost horsepower, so MSD also designed these iron camshaft mounted distributor gears for tighter mesh to the distributor gear.
( 19 )
$126.95
MSD high-current solid state relay blocks take the place of four standard relays and eliminates unsightly wiring. Four independent channels can be activated using either power or ground. Each channel is capable of handling up to 35 amps of continuous current, providing up to 140 amps of power, and also has the capability of pulse width modulation. The blocks can easily be mounted using the supplied hardware and mounting tabs that can be rotated 90 degrees to accommodate various mounting locations. Clean up your wiring with MSD high-current solid state relay blocks. Features include: * Operates from 7 V to 20 V supply * Four independent channels, 35 amps each continuous or 100 amps for 8 seconds * Combined total continuous current rating of 140 amps * Channels can be run in parallel for devices requiring more than 35 amp single-channel rating * Over-temperature, short circuit, and overload protection * Diagnostic LEDs and status indicators * Multiple mounting options * Single wire activation by switching power or ground * Available in red or black * PWM signal can be used--maximum frequency of 150 Hz and a duty cycle range from 50 to 90 percent
( 13 )
$217.95
On Sale
When tested against a competitor's coil, the MSD Pro Power coils produced 33 percent more current at the plug. They have an oil-filled insulated polyester case, an extra-tall high-tension spark plug tower to stop voltage leaks, and rubber shock mounts. They're designed for drag race use only, with MSD 7 and 8 Series ignitions.
( 40 )
$184.95
—
$206.95
On Sale
MSD 8.5mm Super Conductor spark plug wire sets feature a special helically wound core that has just 40-50 ohms of resistance per foot—but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire includes 40 ft. of tightly wound copper for superior conductivity. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference "choke." This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Each set comes with clip-on cylinder markers for easy identification. MSD's 8.5mm Super Conductor wire sets are available in custom or universal-fit applications, assembled or not, with a variety of terminal and boot end options.
( 1950 )
$112.95
—
$218.95
MSD digital 6A ignition controllers--great ignition systems get even better! And, now you can update your ride with the digital circuitry of these powerhouses. MSD lowered the profile for a sleek look and routed the wiring out one side of the unit through a sealed and locked connector for easy installation with a clean, neat look under your hood. More important is what's inside these digital 6A ignitions. Microprocessors, updated circuits and efficient components control every firing to help the ignition make more power with less current draw--each spark packs more than 135 millijoules of energy with up to 530 volts! Others strive where MSD succeeds; join the proven win-win of "fire to drive" with unmistakable, MSD technology at its best--digital 6A ignition controllers.
( 150 )
$249.95
Multi-port EFI systems require a stable fuel supply to maintain the best performance throughout the engine's rpm range. MSD high-pressure, high-flow fuel pumps feature a roller vane pump mechanism, which is extremely resistant to clogging and jamming. The pumps mount in-line (out of the tank) with two supplied cushioned clamps for a quick and sturdy installation. The wire terminals feature brass studs for secure connections. These MSD pumps are ideal as "boosters" for nitrous oxide applications, or as stand-alone pumps for multi-port EFI systems on engines up to approximately 500 hp.
( 50 )
$162.95
MSD Blaster HVC ignition coils are designed for high-rpm, long-duration applications, such as road course and Circle Track racing using the MSD 6 Series ignition. These units feature a 100:1 turns ratio, as well as lower primary resistance to produce high-voltage output. Windings are encased in a durable epoxy and secured with extruded brackets. They also feature a spark plug style terminal and a threaded brass primary stud. These ignition coils are CARB EO-approved and are supplied with rubber shock mounts to help them resist coil vibration. Equip your performance vehicle with MSD Blaster HVC ignition coils and feel the power!
( 34 )
$206.95
Make installation a breeze with MSD ignition coil brackets. They're crafted from aluminum and are made for the specific purpose of keeping your coil braced.
( 6 )
$231.95
MSD Blaster Power Sports ignition coils deliver the most energy for easier starting, quicker throttle response, and powerful spark energy throughout the rpm band of your powerplant. Power Sports coils are direct bolt-on, plug-in replacements for factory units on many popular powersports machines. If you demand maximum performance for maximum fun, these easy, economical MSD upgrades are the perfect fit for your ATV, UTV, motorcycle, snowmobile, or jet ski. Benefits include: * Available in red and black * Optimized coil engineering * Easier starts * Smoother idle * Crisper throttle response * Improved power from idle to redline * Supplied with mounting bracket and hardware
( 4 )
$155.95
On Sale
MSD Street Fire coils will improve the performance of your late model GM or Ford vehicle. The E-core dual connector and TFI coils feature epoxy-filled construction and maximum output voltage. They mount directly in place of the factory coil and accept the factory connectors for an easy installation.
( 640 )
$172.95
$112.95
—
$227.95
MSD distributorless ignition tachometer adapters allow you to install an aftermarket tachometer on vehicles with no distributor and multiple coil packs. These compact tach drivers measure only 1.5"x 3.5"x 2" and are potted with a polyurethane compound for vibration and water protection so it can easily be mounted under the hood. It wires inline on the coils' 12 volt supply wire where it senses the current going through the wire and converts this information into a 12 volt output signal that most aftermarket tachometers use as a trigger signal. MSD distributorless ignition tachometer adapters can be used on 4, 6 or 8-cylinder engines.
( 7 )
$172.95
On Sale
MSD Atomic EFI billet fuel rails are the perfect complement for your Atomic AirForce intake manifold. Whether you're looking for just rails, or complete kits with all the necessary plumbing--these fuel rails will have you looking for any excuse to pop the hood. They feature a bright dip, black anodized finish with laser-etched logos and a 5/8 in. diameter fuel passage flow capacity for high-horsepower applications. Make your engine look as good as it performs with MSD Atomic EFI fuel rails. Features, specs, and parts may include: * Fuel rails are machined to accept large -8 (3/4 in.-16) O-ring fittings * Includes mounting brackets and hardware * Includes four -6 to 3/4 in.-16 O-ring adapters
( 1 )
$338.95
$137.95
—
$249.95
These MSD alternate action switches are designed to be used as auxiliary ignition on/off buttons. They can be mounted to the steering wheel within easy reach of the driver and can be used in a Normally Open or Normally Closed position. MSD alternate action switches are assembled and constructed for harsh racing conditions.
Not Yet Reviewed
$158.95
On Sale
MSD Pro 600 CDI ignition high-output coils developed these powerful coils to provide unrivaled spark energy and dependability. The best choice to equip your Pro 600 CDI, they have the highest current and voltage available in a small compact design, creating over 200 millijoules of spark energy and leaving no horsepower untapped. Along with the unrivaled output of your Pro 600 CDI, MSD high-output coils, everything from Pro-mod's to pulling trucks can perform at a whole new level! Features and benefits: * Designed for extreme racing for the Pro 600 Capacitive Discharge Ignition * Capable of up to 50,000 V to ignite extreme cylinder pressures * Over 200 millijoules of spark energy makes them ideal for use with methanol, ethanol, and E85, as well as forced induction and power adder combinations * Supplied with hardware to mount horizontal or vertical position * Coils are designed to be mounted on Holley's LS valve covers, or OE LS passenger car coil brackets using 72mm bolt spacing * HEI-style secondary tower for secure coil wire connection
Not Yet Reviewed
$112.95
MSD offers these Pro Mag 44 extension harnesses for use with your Pro Mag 44 magneto. These harnesses provide extra length to allow you to mount the Pro Mag 44s in your desired location.
Not Yet Reviewed
$134.95
MSD's distributor hold-down clamps are strong enough to keep the timing locked in place whether you are using an MSD billet distributor or Pro-Mag. These MSD hold-down clamps are precision-made and fit all MSD Pro-Billet Chevrolet distributors and the Pro-Mags. Each of these clamps includes a mounting stud, lockwasher, and nut.
( 24 )
$104.95
These Pro Mag replacement cap and rotor kits are injection-molded from Dupont Rynite material for high voltage insulation characteristics with heavy-duty construction. Inside the cap, there are thick vanes to help agitate the air to prevent the chance of crossfire. Stainless terminals are used for resistance to corrosion, caused by ozone in the cap. The rotor is also molded out of Rynite and features a brass/stainless steel rotor tip, plus a lock screw for secure mounting to the shaft.
( 2 )
$145.95
On Sale
MSD flying magnet crank triggers use four magnets permanently embedded in an aluminum wheel. As the crank rotates, the magnets pass a non-magnetic pickup, which triggers the ignition. These MSD systems include a trigger wheel, pickup, CNC-machined aluminum mounting bracket, and hardware.
( 51 )
$275.95
$151.95
The only way to maximize horsepower from a Honda® or Acura® engine is to get rid of the weak coil mounted inside the cap. These MSD Pro-Cap brass terminal distributor caps are specially constructed to allow the use of an external coil, such as an MSD Power Tower, to accept the high voltage of an MSD Blaster Coil. They also include an 8.5mm Super Conductor coil wire and crimp tool.
( 1 )
$131.95
These MSD Replacement Pro Mag band clamps have been specifically designed for use with your MSD Pro Mag. They are manufactured from billet aluminum and include the mounting bolt for tightening around the magneto housing.
Not Yet Reviewed
$177.95
MSD HVC coils are designed for racing applications using an MSD 7, 8, or 10 series ignition. Due to their unique design, the Pro Power HVC coils are perfect for long duration racing events or on the street. A spark plug-style terminal is used to grip the secondary wire, and a Weathertight connector is supplied for a positive connection.
( 23 )
$218.95
On Sale
When it comes to late model performance parts, nothing beats bolt-on and direct connection components—especially when they improve performance like these new replacement MSD Blaster ignition coils. They're designed with improved materials and windings to produce a stronger spark. This improved spark helps burn the fuel mixture more efficiently, resulting in smooth idle and heightened mid-range rpm power. Choose the OEM replacement designed for your year/make/model application.
( 619 )
$177.95
—
$237.95
Coils have always had to compromise voltage output against current output that is until now. MSD 6 HVC coils are exclusively designed for the HVC Professional Racing Ignition Control, and are a must to be used with MSD 6 HVC ignitions. These HVC coils deliver high voltage to ionize the plug gap, while the spark glows with high current to produce maximum voltage and energy. To accomplish this combination of higher voltage and current, MSD uses an E-core winding design, which is an efficient design where less loss occurs during transfer of electricity due to the closed core of the coil. Give your ride the boost power it needs, with HVC coils from MSD.
( 2 )
$218.95
On Sale
The cap and rotor of any ignition system must be considered maintenance items. Just like when you change the oil and filter in your car, you should always replace your cap and rotor as a set. MSD makes it easy with these cap and rotor replacement kits. The correct rotor is already matched to the correct cap for you.
( 512 )
$126.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
