Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
Availability
597 Results Found For "rod"
Showing In Stock Items. Show All 770 Items.
Clevite H-Series Rod Bearings
Clevite H-Series rod bearings were developed primarily for use in NASCAR type racing but are suitable for all types of competition engines. These H-Series bearings have a medium level of eccentricity, high crush factor, and have hardened steel backs and thin overlays. They also have enlarged chamfers for greater crankshaft fillet clearance and are made without flash plating for better seating. Bearings with .001 in. extra clearance are available for standard size shafts and with or without dowel holes. H-Series bearings are recommended for use with crankshafts that have oversize fillets and where engines run in the medium to high rpm range. They should also be used if contact patterns obtained with Clevite P-Series bearings are too narrow. Contact patterns should ideally cover 2/3 to 3/4 of the bearing surface.
( 168 )
$11.99
—
$19.99
ARP Fuel Pump Pushrods
ARP fuel pump pushrods are made durable to provide required reliability and improved performance. Made from aerospace chromoly steel, they are centerless ground to precise diameter. They have a hollow core to help reduce mass, creating less engine drag, and requiring less energy to operate your vehicle.
( 56 )
$18.99
King SI-Series Rod Bearings
King SI-Series rod bearings are recommended for OE applications. They're designed for aftermarket gasoline or diesel engine rebuilding and performance engines with OE crankshafts. These direct replacements have an improved finish for reducing microscopic ferrite peaks on improperly ground or polished nodular cast iron crankshafts. King SI-Series rod bearings also feature improved oil clearance to reduce wear and increase engine life—which, in turn, lessens operating noise, vibration, and excess oil flow. Hundreds of sets are available; order the bearings recommended for your vehicle.
( 97 )
$10.99
—
$19.99
Trick Flow® Adjustable Pushrod Length Checkers
These 5/16 in. pushrod checkers feature over 1 in. of travel to help you determine the proper pushrod length for your application. A must-have tool for setting up proper valvetrain geometry. They are made from thin-wall steel and have common end configurations for your prefect measurement.
( 176 )
$17.99
Moog Tie Rod Sleeves
Are you looking to freshen up your front suspension? Moog tie rod sleeves will help you finish the job. They connect the tie rods together and are manufactured to stock tolerances. These steering linkage components are available for a wide range of vehicles and applications.
( 127 )
$10.99
—
$19.99
FK JM Series Rod Ends
FK JM Series rod ends feature a heat-treated, zinc plated, and chromate treated alloy steel body. Their ball is made of 52100 steel and is heat-treated and hard chrome plated for durability. JM Series rod ends have heat-treated steel alloy races, which are zinc plated and chromate treated to resist oxidation. These 3-piece, wear-resistant rod ends are precision-made and are offered in metal-to-metal or PTFE-lined styles. Order the size, thread, load capacity and other options available for your application.
( 7 )
$10.99
—
$18.99
Melling Performance PRO-Line Pushrods
Melling Performance PRO-Line pushrods give you the reliability that you need from your valvetrain. They are manufactured from high-quality carbon steel, are hardened for use with guideplates, and exceed OEM specifications. Their pushrods also feature close-tolerance wall thickness and a centerless ground to make sure that they are a matched set. Choose Melling Performance PRO-Line pushrods to keep your valvetrain operating efficiently.
( 12 )
$10.99
—
$18.99
Clevite P-Series Rod Bearings
P-Series rod bearings are the oldest members of the Clevite 77 performance bearing family. They're intended for high-revving engines, especially those where the high rpm cause the rod bores to narrow. To compensate for this distortion, these direct replacements have higher eccentricity and a high crush factor. Clevite P-Series rod bearings are built on hardened-steel backings with extra-thin overlays, and their lower sections have dowel holes for use with aluminum rods, and there are extra-clearance variations available with an additional 0.001 in. of clearance. Order the model designed for your vehicle and engine application.
( 289 )
$10.99
—
$19.99
Melling Pushrods
Melling OEM replacement pushrods are perfect for stock rebuild or mild performance applications where open spring pressures do not exceed 300 lbs. They're manufactured from steel tubing and work well with factory or aftermarket rocker arms. These units are available in a wide range of lengths and other options for fitment on countless makes and models. When you're replacing your valvetrain components, trust Melling pushrods to keep your engine running smoothly.
( 78 )
$10.99
—
$16.99
Sealed Power CP-Series Rod Bearings
Federal Mogul CP-Series rod bearings feature classic tri-metal construction and are a good choice for either street or moderate competition use. They have rugged 1010 steel backings, covered by Federal Mogul's H-24 copper-lead alloy. On top of this is a nickel barrier, followed by the tri-metal (lead-tin-copper) overplate that gives these bearings their strength and fatigue resistance. The bearings are then entirely covered with a flash coating of tin. Order the set designed for use with your make/model and engine application.
( 118 )
$10.99
—
$16.99
Trend Pushrods
Trend Performance is an industry standard in high performance valvetrain technology and a leader in pushrod manufacturing. Manufactured in house, Trend pushrods are one-piece, centerless-ground 4130 chrome molybdenum pieces available with range of wall thicknesses, tube diameters, and lengths. They are pre-formed and centerless ground. Trend's stocking pushrods are designed for use in oval track race cars, drag race cars, hot rods, sport compacts, and marine applications. They are manufactured with 5/16 in. ball/ball ends and are available in lengths of 6.00 in. to 11.55 in. in increments of .025 in. The ball ends are machined to a tolerance of plus or minus .001 in. and the pushrods are laser-etched with the part number and specifications on a black oxide finish.
( 5 )
$10.99
—
$19.50
FK Solid Rod Ends
What rod ends are holding your rear-end together? FK one-piece solid rod ends are made of zinc plated low-carbon steel to use on the rear of your ladder bars. These American-made solid rod ends can be used in areas where there's no angular change and they're built tough to handle the strain of being pushed and pulled. Rod ends are holding your rear-end assembly together, and if one breaks... well, it will definitely add to the excitement of racing! Choose wisely. Replace with FK solid rod ends.
( 7 )
$10.99
—
$19.99
Moog Replacement Tie Rod Ends
Moog replacement tie rod ends are designed as OE replacements for your stock units. Moog replacement tie rod ends feature durable, all-metal construction that is not prone to failure like OE plastic tie rod ends. Since Moog replacement tie rod ends are greasable (except where noted), friction is reduced and contaminants are flushed out. Plus, they have an easy-access wrench flat that allows for the use of a socket for easy installation.
( 804 )
$12.50
—
$19.50
Summit Racing™ Black Max Rod Ends
Are you looking for tough rod ends? Look no further--Black Max rod ends are for you. In independent tests, these rod ends handled 90 percent more load than economy types. The pivoting balls are made from premium 52100 steel that receives a durable chrome plating to prevent wear. The bodies are made from heavy-duty, heat-treated chromoly steel for strength, and have a black oxide finish. So they not only look good, but they won't corrode, either. Jam nuts are included.
( 41 )
$14.99
—
$18.99
Howards Cams Pushrod Length Checkers
Howards Cams offers these pushrod length checkers as easy and economical tools to lay out and determine proper pushrod length for proper valvetrain geometry. This is necessary to obtain the desired results from the cam and ensure that damage is not done to the rest of the valvetrain.
( 31 )
$17.99
FK JMX/JMXL Series Rod Ends
FK JMX/JMXL Series 3-piece rod ends are precision-built for high strength. The bodies and races are heat-treated steel alloy that is zinc plated and chromate treated for corrosion resistance. The ball is hard chrome plated 52100 steel, offering excellent wear and durability. These rod ends are available in a wide range of size and options, with right (JMX) or left (JMXL) hand threads. You can also choose JMX/JMXL in metric dimensions with PTFE liners for high load capacities. FK Bearings provide the expertise and quality ends to meet your needs. Order the 3-piece JMX/JMXL Series rod ends designed to fit your application.
( 43 )
$13.99
—
$19.99
FK ALJM Series Rod Ends
Thanks to demand from the open wheel market, FK Rod Ends offers ALJM Series rod ends for use on bird cages with a 3/8 in. bore. Available in a choice of sizes, ALJM Series rod ends also fit Jacobs ladders without drilling or using bushings. These 3-piece, precision wear-resistant rod ends feature 7075-T6 aluminum bodies with a hard, red anodized finish. Heat-treated steel alloy races are zinc plated and chromate-treated for strength and durability. ALJM Series rod ends have a heat-treated, hard chrome plated 52100 steel ball. PTFE liners are available for these rod ends.
( 6 )
$11.50
—
$17.50
FK HIN-T Series Rod End Receiver Bearings
FK HIN-T Series rod end receiver bearings are ideal to accommodate severe misalignment angles. Their structural integrity is the result of heat-treated alloy steel construction, precision-machined to hold tight tolerances. In addition, these FK HIN-T Series rod end receiver bearings have PTFE self-lubricating liners and are offered in a variety of sizes to suit your application.
Not Yet Reviewed
$19.99
QA1 X Series Rod Ends
QA1 X Series rod ends are an excellent choice for 4-link and ladder bar applications. They feature metal-to-metal support for heavy shock loads and increased cross-sectional thickness for greater tensile strength. The heat-treated ball is chrome plated, and the heat-treated chromoly steel body is coated for corrosion resistance. Add in a self-sealing liner and a self-lubricating liner that won't pound out, and you can see why the QA1 X Series is the choice for many racers.
( 61 )
$10.99
—
$19.99
FK ECM/ECF Series Rod Ends
FK ECM/ECF Series rod ends are frequently used in street rod applications without high-impact or load requirements. These economy rod ends feature 2-piece, metal-to-metal construction. Their bodies are constructed using low carbon steel and are zinc plated and chromate treated for performance and durability. Their ball is made of 52100 steel and is hard chrome plated for additional strength.
( 16 )
$10.99
FK CM/CF Series Rod Ends
FK CM/CF Series rod ends are economical replacements featuring 2-piece, metal-to-metal construction. Their bodies are made using low-carbon steel that's zinc plated and chromate treated; and their balls are made of 52100 hard chrome plated steel. These high-quality rod ends are often used in street rod applications without high-impact or load requirements. Order the size and thread options needed for your application.
( 19 )
$10.99
—
$17.99
Clearance
FK ALJF Series Rod Ends
If you're looking for precision-made, wear-resistant rod ends, look no further than FK ALJF Series rod ends. They feature 7075-T6 aluminum bodies with an attractive, hard anodized red finish. Their balls are made of 52100 steel that's heat-treated and hard chrome plated for strength and durability. Their races are heat-treated steel alloy and are zinc plated to resist oxidation. These 3-piece rod ends are available with PTFE liners.
( 5 )
$10.99
—
$16.99
FK KMX Series Rod Ends
FK KMX Series rod ends are constructed with a heat-treated and hard chrome plated alloy steel body with a 52100 steel hard chrome plated ball. They are 2-piece, injected nylon-style rod ends featuring a race made of nylon 10 or an equivalent.
( 7 )
$18.99
—
$19.99
QA1 PCY Series Rod Ends
QA1 PCY Series rod ends are for applications requiring high misalignment. These rod ends offer superior load ratings over carbon steel 2-piece rod ends, and PCY versions automatically include PTFE lining. Offering the highest misalignment available in the industry, QA1 PCY Series rod ends are the ideal choice. Features of the PCY Series: * Ball is 52100 bearing steel, heat-treated, hard chrome plated, and precision ground * Body is chromoly steel, heat-treated, and PTFE lined * Available in male or female, right hand or left hand, and several bore and thread sizes
( 29 )
$11.99
—
$19.99
