6 Results Found For "aftermarket knock sensor"

Squeeze the most performance possible from your fuel-injected setup with an engine management system from Summit Racing. Explore engine control computers which tune,...

Squeeze the most performance possible from your fuel-injected setup with an engine management system from Summit Racing. Explore engine control computers which tune, manage and regulate the input/output signals, as well as power adders on your vehicle’s engine. Check out engine control systems from Holley, FAST, Chevrolet Performance, AEM, Ford Performance, among others, and choose the ECU best-suited for your application! Get yours today from Summit Racing!

Showing In Stock Items. Show All 8 Items.

Individual Parts

Part Groups

Results 1 - 6 of 6

DIYAutoTune MegaSquirt Gen 2 Plug-and-Play Engine Management Systems

DIYAutoTune MegaSquirt Gen 2 plug-and-play engine management systems are standalone units designed as direct-fit, factory ECU replacements offered for a variety of foreign and domestic vehicles. These powerful and cost-effective options typically require an hour or less for installation, and each includes a base map to get the motor fired up easily and ready for fine-tuning to match your engine's needs--from mild to wild. MegaSquirt Gen 2 ECUs get the job done with an impressive feature list that will let you do a lot more than you'd expect anywhere near this price point. DIY AutoTune MSPNP Gen 2 ECUs typically feature: * Fully plug-and-play installation--no wiring required for basic functionality * Base map is pre-loaded to help your engine start on the first turn of the key * Real-time tuning and data-logging with a laptop connection * Supports most aftermarket wideband sensors * 16 x 16 fuel tables allow high-resolution tuning * 12 x 12 ignition tables * Multiple acceleration enrichment strategies * Closed-loop idle speed control * Air conditioner control * Onboard peak and hold drivers support both high and low impedance injectors--no external ballast resistor is needed * Allows removal of stock airflow meter or stock MAF sensor, if so equipped * 12 x 12 air fuel ratio target tables for use with wideband oxygen sensor for precise tuning and table trim * Built-in 2-step rev limiter/launch control with flat shift * Real-time barometric correction * Internal 4-bar MAP sensor reads up to 44 psi of boost * Over-boost protection * Closed-loop boost control (requires boost solenoid kit) * Knock sensor input with adjustable sensitivity * Headphone output for knock sensor--listen for knock while you tune! * Table switching input--change fuel and spark maps on the fly for different fuels, nitrous activation, etc. * Input for flex fuel sensor--switch between E85 and gasoline on the fly! * CAN Bus connector allows interconnection of other MegaSquirt-compatible devices for additional functions, like: EGT input, automatic transmission controller, additional sensors ... the possibilities are limitless! * MegaSquirt Gen 2 plug-and-play ECU * MSPNP RS232 serial tuning cable, 6 ft. (USB adapter sold separately, if needed) * Tuning software and documentation USB stick * 6 ft. vacuum hose for MAP signal and "T" fitting * Four screws for ECU mounting

4.67 out of 5 stars ( 3 )

$869.99

DIYAutoTune MegaSquirt MS3Pro Plug-and-Play Engine Management Systems

DIYAutoTune MegaSquirt MS3Pro plug-and-play engine management systems are standalone units designed as direct-fit, factory ECU replacements. They are offered for a variety of vehicles for off-road and race applications. These powerful and cost-effective options typically require an hour or less for installation, and each includes a base map to get your engine started with the first turn of the key, ready for fine tuning to match your engines exact needs. DIYAutoTune MS3Pro PNP ECUs typically feature: * Fully plug-and-play installation--no wiring required for basic functionality * Base map is pre-loaded to help your engine start on the first turn of the key * Real time tuning and data logging with a laptop connection * 8 GB internal data logging with built-in SD card * Supports most aftermarket wideband sensors * 16x16 fuel tables allow high resolution tuning * 16x16 ignition tables * Multiple acceleration enrichment strategies * Closed loop idle speed control * Air conditioner control * Sequential fuel injector channels with individual trim tables * Onboard peak and hold drivers support both high and low impedance injectors--no external ballast resistor is needed * Allows removal of stock MAF sensor * 12x12 air fuel ratio target tables for use with wide band O2 sensor for precise tuning and table trim * Multiple traction control strategies * Built-in 3-step rev limiter/launch control with flat shift and burnout rev limiter * Real time barometric correction * Internal 4-bar MAP sensor reads up to 44 psi of boost * Over boost protection * Closed loop boost control (requires boost solenoid kit) * Rally-style anti-lag * Water injection control--on/off or variable * Knock sensor input with adjustable sensitivity, crank angle windowing, and more * Table switching input--change fuel and spark maps on the fly for different fuels, nitrous activation, etc. * Input for flex fuel sensor--switch between E85 and gasoline on the fly! * CAN Bus connector allows interconnection of other MegaSquirt-compatible devices for additional functions like, EGT input, automatic transmission controller, additional sensors ... the possibilities are limitless! * MS3Pro plug-and-play ECU * Tuning cable * Tuning software and documentation on USB stick * 6 ft. vacuum hose for MAP signal and "T" fitting * Registered version of TunerStudio and MegaLog viewer

Not Yet Reviewed

$1,399.99

—

$1,499.99

DIYAutoTune MegaSquirt MS3Pro EVO Standalone Engine Management Systems

DIYAutoTune MegaSquirt MS3Pro EVO standalone engine management systems are scaled up, more capable units due to the shared technology with their big brother, MS3Pro Ultimate. EVO ECUs by AMP EFI do not have peak and hold injector drivers, but they do share some increased I/O, an onboard 4-bar MAP, barometric pressure sensor, and 5 diagnostic LEDs. Whether you're running down the drag strip, the road course, the salt flats, or whatever your racing venue of choice, DIYAutoTune MS3Pro EVO ECUs will deliver winning control. MS3Pro EVO ECUs feature configurable inputs/outputs: * 10 high-impedance injector outputs * 8 logic level spark outputs * 3 PWM outputs * 2 digital outputs * 7 analog inputs, plus built-in MAP, Baro, and internal ECU temperature sensor * 3 high-current digital/pwm outputs * 3 digital frequency inputs * 4 variable reluctor conditioned inputs MS3Pro EVO standalone systems feature: * VE-based tuning * Speed density, Alpha-N, MAF-based tuning and blended algorithms * Up to 12 sequential saturated fuel injector outputs * Up to 12 cylinder sequential support * 2D or 3D table views * The tuner can toggle between 2D or 3D table views with a single click * Individual cylinder fuel and spark trim tables * Table switching * VVT control (4 channels) * Generic wheel decoder allows for support of nearly any standard trigger/aftermarket trigger pattern * Supports 50+ specialty OEM and aftermarket ignition systems using factory cam/crank wheels and sensors * Support for odd-fire and even-fire engines * Capable of controlling even-fire, odd-fire, piston, rotary, and even radial engines * Fuel-only mode--disables ignition output features for control of fuel injection only * Internal SD card high-speed data logging * Traction control multiple strategies * E85 flex fuel sensor input * Long-term fuel trim--OE-style automatic fuel trim to allow for changes in engine over time * High-power time enrichment--allows for richer mixture after extended time in high power * Multiple acceleration enrichment strategies * Nitrous control strategies * 3-step rev limiter with flat shift * Trans-brake and bump box control * Advanced launch control strategies * Pit lane limiter--speed limiter for pit lane, reduces engine power by spark retard/cut or fuel cut; can limit based on VSS or rpm if no VSS input is available * Rally-style turbo anti-lag with rotational idle * Allows cyclic fuel and spark cut * Controls idle valve and configurable outputs for external fuel or air supply * Boost control--multiple open and closed loop strategies * Idle control--multiple open and closed loop strategies * Water and methanol injection * Fuel pump control * Intelligent knock detection and response--two channels * Multiple Engine Protection and fault mode strategies * Generous spare I/O for any standard/custom I/O needs * Air conditioner control with feed-forward idle-up * Cooling fan control--programmable fan on and off activation points; can be configured to run fan with engine running only, or when engine is running and not running * Alternator field control/voltage regulation * Comprehensive Test Modes * CAN Support for I/O expansion--virtually limitless I/O capability * CAN Support for third party dash devices * Android compatible * Self-calibration * Fully enabled * Redundant signal ground wiring * Dual external 5 V ref supplies, individually fused * No dark current * Field upgradeable firmware

Not Yet Reviewed

$674.99

Ford Performance Parts Crate Engine Control Packs

Looking to add a Ford Performance Parts crate engine to your custom built vehicle? Take the complexity and mystery out of wiring your new build with Ford Performance Parts crate engine control packs! Features include: * Unique controls pack harnesses to replace stock body harnesses; designed for custom-built vehicles * OBD-II diagnostic ports to assist in vehicle calibration uploads and diagnosis of problems * PCMs with Ford Performance Parts performance calibration (custom calibration required on some engines and for aftermarket intake systems) * Electronic throttle control accelerator pedals, eliminating throttle cable routing problems * Power distribution modules * Requires return-type fuel system, will not work with returnless fuel system

5.0 out of 5 stars ( 2 )

$1,949.99

On Sale

Holley Terminator X Engine Management Systems

Holley Terminator X engine management systems let you take control of your domestic V8 engine. These kits give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X features real-time fuel learn, high impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. All systems come fully loaded with base maps for common engine combinations to get you out of the garage and onto the road or track fast. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors. (Will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables: 4 x 1D tables, 1 x 1D per gear table, 4 x 2D tables, 1 x 2D per gear table * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most domestic V8 engines, as well as tuning and gauge display functions (not available with every kit)

4.48 out of 5 stars ( 96 )

$1,949.95

On Sale

Holley Terminator X MAX Engine Management Systems

Holley Terminator X MAX engine management systems let you take control of your domestic V8 engine. They give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X MAX features real-time fuel learn, high-impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. Also, Holley offers the X MAX systems with either or both drive-by-wire (DBW) throttle body control or transmission control. All kits come fully loaded with base maps for common domestic V8 engine combinations to get you out of the garage and onto the road or track fast. Order the model recommended for your vehicle application. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors (will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM, and for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables can be used for any custom tables * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most V8 engines, as well as tuning and gauge display functions

4.18 out of 5 stars ( 92 )

$2,299.95

$2,068.95

Page 1 of 1