Availability
Showing In Stock Items. Show All 38 Items.
On Sale
PerTronix Ignitor® solid-state ignition systems deliver more energy with greater timing accuracy. The secret lies in the trigger magnets, which spin with the rotor and operate a switching module that requires no external control box. These systems are immune to heat, oil, and debris—and install in about 15 minutes with only two wires to connect. They come with a switching module, hardware, and instructions. Ignitor® is an ideal choice for collector car restoration because it fits entirely under the distributor cap.
( 1000 )
$125.15
—
$183.50
$112.64
—
$165.15
On Sale
Not ones to leave well enough alone, the engineers at PerTronix set out to improve upon their highly successful Ignitor® ignition conversion systems. The Ignitor II® conversion systems have all of the same quality features as the original Ignitor®, plus a powerful microprocessor controller to deliver, on average, 4x more available energy between 3,000 and 5,000 rpm than standard ignition systems. They're an ideal choice for collector car restoration because they fit entirely under the distributor cap. Order the model recommended for your year/make, distributor and engine application. Features include: * Compatible with 12 V negative ground systems and any induction coil * High-rpm performance is improved when used with the PerTronix Flame-Thrower II super low- resistance (0.6 ohms) 45,000 V coil * Adaptive dwell maintains peak energy throughout the entire rpm range, reducing misfires while improving engine performance * Develops, on average, 2x more available plug voltage * Peak current level is reached just prior to spark for maximum energy without heat build-up, increasing coil and module life * Never change points again * Adjusts spark timing at higher rpm to compensate for the inherent electronic delay * Senses startup and develops more energy for quicker, easier starting * Built-in reverse polarity and over-current protection shuts down the system, preventing component damage * Cannot be used with solid core spark plug wires; suppression-style or spiral-wound spark plug wires must be used
( 294 )
$185.65
—
$223.85
$167.08
—
$201.46
On Sale
PerTronix Ignitor lobe sensor solid-state ignition systems replace breaker points and troublesome factory units with a dependable, self-contained, and maintenance-free electronic ignition system. The Ignitor has been called the "stealth" ignition because of its quick installation and nearly undetectable presence under your distributor cap. There is no "black box" to clutter the engine compartment. PerTronix Ignitor has proven itself in applications ranging from race cars to tractors. Order the model recommended for your vehicle, engine, and distributor application. Product features: * Delivers twice the voltage to your spark plugs—increasing horsepower, fuel economy, and spark plug life * 2:1 improvement over "points" in current fall time for increased coil output * No points to burn or moving parts to wear out * No magnetic sleeve or ring needed; uses existing distributor lobe for sensor trigger * Epoxy molding makes the module impervious to dirt, oil, grease, and moisture * Stable timing—no need for any adjustments * Will trigger most multi-spark CD ignitions * Available for 6 and 12 V negative and positive ground systems
( 208 )
$144.25
$129.82
On Sale
These PerTronix Ignitor III® solid-state ignition systems feature an adaptive dwell that maintains peak energy throughout the entire rpm range, reducing misfires while improving engine performance. Peak current level is reached just prior to spark for maximum energy without the heat buildup, increasing coil performance and module reliability. They adjust spark timing at higher rpm to compensate for the inherent electronic delay, sense startup, and develop more energy for quicker, easier starting. The PerTronix Ignitor III® solid-state ignition systems have a built-in LED for user feedback confirmation of the rev limiter setting.
( 83 )
$223.85
$201.46
On Sale
With their optimized winding design, PerTronix Flame-Thrower HEI and TFI ignition coils are a great upgrade from stock. They produce more than 50,000 V of energy to zap your plugs, for fuller, more complete combustion and better power. When used with their companion Flame-Thrower ignition modules, they produce more than twice the energy of a stock system at the plugs. They're wrapped in rugged alkyd housings and are available for both distributor-mounted and external applications.
( 63 )
$79.55
—
$96.00
$71.60
—
$86.40
On Sale
PerTronix's Flame-Thrower 7mm "Stock Look" spark plug wire sets are designed to give you the ultimate in high performance, while retaining a stock appearance. The core consists of a carbon-impregnated fiberglass center that is spiral-wound with stainless steel alloy. They also feature: * Low 500 ohm per foot resistance * Silicone jackets to resist high temperatures, moisture, oil, and chemicals * EPDM rubber inner insulation for superior heat resistance and the prevention of arcing and voltage leaks * Fiberglass reinforcing braid for added strength and flexibility
( 140 )
$79.55
$71.60
On Sale
ThunderVolt 8.2mm wires from Taylor are an easy, proven, dyno-tested way to gain more power—simply by changing your spark plug wires! These factory replacement, ultra-high performance ignition wire sets are loaded with features and benefits, including: * 50 ohms of resistance per foot * 100 percent silicone 2-layer jacket * Ferrite spiral-wound coated core * RFI and EMI-compatible for all ignition systems * Dyno-tested to outperform the competition * Superior spark energy * Increased horsepower * Significant torque gains * Smoother idle * Improved fuel economy * Universal, race, and custom fit sets available
( 648 )
$101.85
$91.66
On Sale
PerTronix's Flame-Thrower Street/Strip HEI distributors will produce 67 percent more energy in the coil, and deliver twice the energy across the spark gap. Plus, they deliver misfire-free performance up to a minimum of 7,500 rpm, a 3,000 rpm improvement over most original HEIs. Each distributor uses a new aluminum housing, cast and machined from a strong but lightweight A384 alloy. High-quality bronze sintered bushings are installed, aligned, and bored for accuracy and extended mileage use. Features include an adjustable vacuum advance, a high-performance mechanical curve kit, aluminum housing, a high dielectric strength cap with solid brass terminals, a balanced rotor, and a centerless-ground shaft.
( 49 )
$355.95
$320.36
On Sale
Taylor Street Thunder spark plug wire sets offer great performance at an affordable price. They feature 8mm diameter black silicone construction with synthetic jacketing to resist heat, oil, and abrasion. Their 500 ohm per ft. resistance delivers greater spark energy, while improving power and fuel efficiency. By using a Kevlar® helically spiral-wound core conductor, Street Thunder wires provide greater strength and durability to suppress electromagnetic and radio frequency interference. Matching black silicone boots protect against high exhaust temperatures and double spring locking terminals make quick vibration-proof connections. Taylor Street Thunder spark plug wires are available in universal, race-fit, or custom-fit styles. Select the set that best suits your application.
( 444 )
$50.90
—
$65.10
$45.81
—
$58.59
On Sale
ACCEL HEI in-cap Super Coils provide more high-rpm power and overall performance. Compatible with both original and computer-controlled HEI ignition systems, ACCEL HEI in-cap Super Coils are designed to resist shock and vibration. They have a finned cover that aids cooling, and hardware is included.
( 41 )
$100.95
—
$123.95
$75.95
—
$92.96
On Sale
PerTronix Flame-Thrower HEI III 4-pin ignition modules feature multiple sparks through the entire RPM range, plus an integrated high resolution digital rev-limiter. The rev-limiter settings are displayed with a LED feedback for precise RPM settings. Adaptive dwell maintains peak energy throughout the entire RPM range, reducing misfires while improving engine performance. Peak current level is reached just prior to spark for maximum energy without the heat build-up, increasing coil performance and module reliability. The PerTronix Flame-Thrower HEI III 4-pin ignition modules adjusts spark timing at higher RPMs to compensate for the inherent electronic delay and they can sense startup and increases energy for quicker, easier starting.
( 47 )
$112.95
$101.66
On Sale
PerTronix Ignitor II® lobe sensor solid-state ignition systems are smarter! Ignitor II units sense the coil current level and employ a powerful micro-controller to adjust the dwell. Variable dwell helps to maintain peak energy throughout the entire rpm range, and these systems develop up to four times more energy between 3000 and 5000 rpm than standard ignition systems. Order the kit recommended for your vehicle and engine application. Features include: * Adaptive dwell maintains peak energy throughout the entire rpm range, reducing misfires while improving engine performance * Develops on-average four times more available energy between 3000 and 5000 rpm, and two times more available plug voltage * Compensates for inherent electronic delay by adjusting the spark timing throughout the entire rpm range * Synchronized peak current and spark timing reduces heat build-up * Senses startup and develops more energy for quicker, easier starting * Built-in reverse polarity and over-current protection shuts down the system, preventing component damage * No magnetic sleeve or ring needed; uses existing distributor lobe for sensor trigger
( 31 )
$190.95
$171.86
On Sale
Bigger, better wire! Taylor 409 Race-Fit Pro Race spark plug wires start with Taylor's 8mm wires (available in spiral-wound or solid core) with a silicone inner insulator, fiberglass braid, and a 100 percent pure silicone jacket. Then they add a heat-treated fiberglass mesh skin and a third layer of pure silicone to get a full 10.4mm diameter. Taylor bonds pure silicone boots directly to the wires. The results are wires that have a 100,000+ V dielectric strength rating that gets more spark to your plugs.
( 157 )
$179.30
$161.37
On Sale
Pertronix Flame-Thrower ignition modules for GM and Ford distributors are direct replacements for the OEM modules and provide enhanced high-rpm performance. Flame-Thrower modules are available for most GM car and truck applications using both remote and in-cap coils in 4-pin, 7-pin, and 8-pin configurations. A Ford Thick Film Ignition (TFI-IV) module is also available (distributor mount only). Thick film technology on alumina ceramic substrates removes heat for greater accuracy and improved reliability, while laser trimming gives precise peak current control for increased energy output. Each module is tested twice with automated equipment to ensure trouble-free operation.
( 42 )
$70.00
—
$96.00
$63.00
—
$86.40
On Sale
Looking for a good cap and rotor for your HEI distributor? These Pertronix caps and rotors are made from a high-dielectric, 60 kV-rated alkyd molding compound to minimize crossfire and "arc-thru." They include nylon rotor hold-down screws, a low-resistance coil brush for a more efficient spark, and brass terminals for a long life.
( 11 )
$45.60
—
$46.15
$41.04
—
$41.54
On Sale
ACCEL SuperStock coils are excellent high-performance coils. They're designed with optimized low resistance and a high turns ratio, for higher energy output. This also results in quicker starts, improved throttle response, and more high-rpm power.
( 93 )
$65.89
$49.42
On Sale
ACCEL SuperStock 4000 Series spark plug wire sets will upgrade your OE ignition system for high-spark delivery levels and RFI suppression. They extrude the silicone jacket over a tightly woven, rugged fiberglass braid that meets or exceeds OE specifications. ACCEL offers their SuperStock 4000 Series wire sets in various color schemes to match nearly any application! More product features include: * Jackets rated up to 450 degrees F * 7mm or 8mm yellow, red, black, and blue silicone jackets * Orange and other color-matched spark plug boots with terminals * Available for pre and post-HEI vehicles * Custom-fit, universal, and import
( 133 )
$63.25
$47.44
On Sale
Experts agree that HEI ignition performance relies on a quality module and coil. Pertronix believes the combination of a great module and a great coil makes their Flame-Thrower HEI distributors the best. They've engineered the module and coil to work together to provide you with superior ignition performance on the street or track. Compare the Flame-Thrower high performance module and coil to an original GM HEI distributor and you'll find these improvements: * Operates without misfires up to a minimum of 7,500 rpm, nearly 3,000 rpm higher than most enthusiasts report with their original HEI * Produces 67 percent more energy in the coil * Spark breakdown time (the amount of time until the spark plug has enough voltage to spark) is 45 percent faster, resulting in more accurate timing throughout the rpm range * Delivers twice the energy across the spark gap (during a one-millisecond burn time) * Spark duration and more energy to the spark allow wider plug gaps (.050 in.-.055 in.), increasing flame kernel growth These are dramatic improvements, not just because of a great module and coil, but also because they've been designed to work as a team to produce these results. Models and options are available for applications from the 1950s and up.
( 22 )
$355.95
—
$383.00
$320.36
—
$344.70
On Sale
PerTronix Flame-Thrower plug and play billet distributors with Ignitor II® module are designed to provide maximum ignition performance and easy installation, all at a price that you can afford. They allow you to upgrade your outdated points or stock electronic distributor with a performance-proven unit. The distributors feature the patented Ignitor II® electronic ignition module and a CNC-machined 6061 T-6 polished billet housing. PerTronix electronics are compatible with any inductive ignition system coil, but high-rpm performance can be improved when they are used with the low-resistance (0.6 ohm) Flame-Thrower II coil. Their stand-alone design makes them plug-in units that require no additional ignition, but they are compatible with multi-spark CD ignition boxes for outstanding versatility. Additional features include a tempered shaft, an upper roller bearing, and an oil-impregnated sintered bronze lower bushing. The PerTronix Flame-Thrower plug and play billet distributors with Ignitor II® module come with a factory-set performance curve, a mechanical advance limiting adjustment, and a small, high-dielectric strength cap and rotor for applications with little clearance.
( 356 )
$398.40
—
$431.25
$358.56
—
$388.12
On Sale
Taylor Spiro-Pro spark plug wire sets are the finest high performance street and race wires available today. They offer maximum firepower without radio interference, provide up to 10 times less resistance than standard resistor core wire—and are a must for electronic ignitions, on-board computers, stereos, and pit radios. Other features include: a 100 percent silicone inner and outer jacket that provides heat protection up to 600 degrees F; low-profile silicone boots with grips; and double spring locking spark plug terminals for a secure connection. The wire sets are available in a variety of boot and distributor terminal ends, assembled or not, and nine vibrant color options. Order the universal or vehicle-specific set that best suits your application.
( 662 )
$94.40
$84.96
On Sale
Taylor High-Energy spark plug wire sets are an outstanding choice for replacement or a performance upgrade. These wires feature heat-resistant silicone jackets and boots, double spring-locking spark plug terminals for better gripping, an 8mm size for high-compression engines, and a resistor core to suppress radio interference. The spark plug wires can withstand temperatures of up to 500 degrees F—and they're available in a variety of options for distributor terminal and boot ends, assembled or not, and universal or direct-fit for specific applications.
( 222 )
$50.90
—
$62.90
$45.81
—
$56.61
On Sale
These Mallory Unilite distributors give you accurate, maintenance-free ignition timing. Instead of old-fashioned points systems, they have photo-optic, LED-triggering systems that never vary or wear out. You get increased rpm potential, improved combustion, longer spark plug life, and better cold-weather starting. Hooking one up is a simple 3-wire connection, and they come with your choice of adjustable mechanical and/or vacuum advance, self-lubricating bushings, and a Super-Duty cap and rotor.
( 56 )
$599.95
$329.95
On Sale
When it's time for a tune-up, PerTronix offers quality distributor caps to replace your worn-out original. Why take chances with old, questionable, or faulty ignition components that can leave you stranded. PerTronix distributor caps are designed to exceed OEM specifications for dependable, accurate, maintenance-free operation. Trust your vehicle's ignition system needs to PerTronix; order the model and options best suited for your vehicle.
( 35 )
$40.70
$36.63
On Sale
Flame-Thrower Race HEI distributors from PerTronix produce 42 percent more energy in the coil, with 46 percent faster spark breakdown time. This allows 48 percent more peak current to reach the spark plug, compared to their Street/Strip HEI distributors. That's an enormous improvement over stock HEIs and most aftermarket HEI distributors. A specially designed vacuum lockout mechanism prevents timing adjustments that change rotor phasing, adversely affecting the burn time and efficient fuel combustion. The rotor plates are TIG-welded to the mechanical advance mechanism, preventing high-rpm distortion and improving mechanical reliability. Each distributor uses a new aluminum housing cast and is machined from a strong, but lightweight A384 alloy. They're supplied with a high-dielectric strength cap with solid brass terminals, a balanced rotor, and a low-resistance center coil brush. Also included are nylon rotor hold-down screws and a factory-installed, high performance mechanical curve kit with precision-machined weights and a center plate. A hardened, machined steel gear is standard, along with an electronic module and coil combination that excels in the 6,000 to 8,500 rpm range. These distributors are great for both Circle Track and drag race applications where factory-type HEI distributors are mandated.
( 9 )
$431.25
—
$463.10
$388.12
—
$416.79
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
