Availability
Showing In Stock Items. Show All 35 Items.
Edelbrock Performer intake manifold and carburetor kits contain all of the necessary pieces to upgrade your induction system. They include an Edelbrock Performer aluminum intake manifold, an intake gasket set, intake manifold bolts, a carburetor stud kit—and an Edelbrock Performer Series 600 cfm electric choke; a Thunder AVS 650 cfm electric choke; or a Thunder AVS 800 cfm electric choke (depending on your engine C.I.D.). The EnduraShine bright silver chrome finish is optional and resists discoloration from heat; it features a top clearcoat to enhance abrasion and chemical resistance. Edelbrock Performer intakes are designed to deliver improved throttle response over stock intakes. Are you ready for a change? Edelbrock Performer intake manifold and carburetor kits are available for small block and big block muscle car, hot rod, truck, and street vehicle applications.
( 34 )
$971.95
Offenhauser Dual Port intake manifolds feature completely separate runner systems for the primaries and secondaries for more power across the rpm range. At low-load, the primaries feed the air/fuel charge through the smaller bottom passages at near sonic speed, improving power and efficiency. When the secondaries open, their charge goes through the bigger, cooler upper passages. Then, in turn, it is rammed into the cylinders when it encounters the high-velocity mix from the primaries. The results are better fuel economy and a 15-30 percent power increase across the entire rpm range. These manifolds are available in a variety of styles and options for many year/make and engine applications.
( 45 )
$799.99
Trick Flow® Track Heat® EFI intake manifolds deliver a perfect balance of airflow distribution and velocity. The result is excellent low-end torque and superior horsepower from 1,500 to 6,500 rpm. These units are available in kits with a natural finish aluminum lower manifold and an aluminum upper plenum in your choice of silver powdercoat, black powdercoat, and natural finishes. The manifolds have a 75mm throttle body inlet and are designed for use on non-EGR engines. Additional features: * Small cross-section with 12.200 in. runners * Overall height to the upper manifold flange is 10.200 in. * Overall height to the lower manifold flange is 4.625 in. * 2.000 in. x 1.200 in. port size at head * 2.000 in. x 1.200 in. port size at mating flange The upper plenums and lower manifold are also available separately.
( 3 )
$888.99
—
$892.99
Old school looks, modern performance, and advanced manufacturing all rolled into one—Trick Flow's® R-Series Tunnel Wedge intake manifold for Ford 390-428 delivers just that. Part of the original Tunnel Wedge's cool factor was its appearance, so Trick Flow® took special care to match the looks of the legendary OEM version while improving upon its performance. Trick Flow® was able to maintain the original carburetor locations—but on the inside of the manifold, Trick Flow® overhauled the port design for more airflow and incorporated a new O-ring sealed bottom plate. Cast in premium-grade A319 aluminum, the manifold is topped with carb flanges machined for original Ford FE Tunnel Wedge-style square bore carburetors. Mounting hardware is included.
( 4 )
$999.99
Prepare your pony for the street and strip! The Edelbrock Performer 5.0 RPM II manifolds are designed for 1986-95 5.0L Mustangs and have shown significant gains in horsepower over existing designs in the 1,500 to 6,500 rpm range. That makes these intakes ideally suited for street and strip applications. The manifolds consist of a V-shaped crossover with an increasing cross-sectional area, which passes over to eight large tapered runners. The upper manifold is powdercoated light titanium gray.
( 5 )
$990.95
On Sale
These Summit Racing™ intake manifold, carburetor, and air cleaner Pro Packs include all of the necessary parts to change out your engine's induction system. They feature an aluminum intake manifold, carburetor, air cleaner, carburetor studs, and gaskets. Available for Ford, Chevy, Mopar, and Pontiac, these Summit Racing™ intake manifold, carburetor, and air cleaner Pro Packs will give your engine increased horsepower and torque and better drivability.
( 127 )
$1,046.51
$762.92
—
$950.92
These Ford Performance Parts 4.6L 3-valve performance intake manifolds feature high-flow runners and an open plenum design for maximum flow, while still fitting underneath stock Mustang hoods. They are manufactured from lightweight composite plastic and have been tested up to 20+ psi; perfect for use in forced induction applications. Ford Performance Parts 4.6L 3-valve performance intake manifolds include a set of intake gaskets to complete the installation. Additional technical information: * Works well with Ford Performance M-6550-3V hot rod camshafts, M-6049-N3VPA high performance CNC-ported 3V cylinder heads, and M-9926-3V 62mm throttle bodies * Less heat soak than aluminum intakes * MAP sensor mounting boss for speed-density applications * Calibration required (not included) * Throttle body not included * Does not fit with Ford Performance strut tower braces
( 11 )
$786.99
On Sale
Holley's low-profile intake manifold for Ford's 7.3L Godzilla engine, when paired with a 20-340/20-340BK oil pan and accessory drive kit, allows for easy installation into vintage vehicles, kit cars, and other space-restricted applications while retaining the factory hood. The design focus for these manifolds was equal cylinder distribution and great street manners. The low-profile intake manifolds offer a much cleaner alternative to the original plastic intake; they provide anywhere from 2 to 3.5 in. of additional clearance, will correct the OE throttle body angle by 55 degrees, and increase the opening to 92mm. With three throttle body options, sturdy cast aluminum construction, a removable lower panel, and long runners to maintain the 7.3L's already substantial torque offering, this is a must-have for any Godzilla project. Throttle Body Options: * 1) 1986-1993 5.0L Mustang style drive-by-cable throttle bodies * 2) 2020-2023 7.3L drive-by-wire throttle body * 3) 2020-2023 GT500 drive-by-wire throttle body (requires P/N 300-903) Compatible Engine Components: * 1) Factory accessories as well as Holley accessory drives (except for 20-380 and 97-409) * 2) Factory fuel rails and Holley 534-265 / 534-266 billet rails Intake manifold features: * Lower profile (2+ inches) than the OE intake manifold * Sturdy cast aluminum construction that will hold up to the elements and forced induction * Perfect complement to Holley's Godzilla accessory drive and oiling system (20-320 / 20-320BK / 20-340 / 20-340BK) for fitment into tight engine bays * Removable lower intake panel that can be removed for additional porting, nitrous, etc. * Incorporates long runners for solid low-end torque * Includes throttle body gasket and all necessary O-rings and adapters to mount to the engine * Compatible with OE or Holley accessory drives and OE or Holley fuel rails * Corrects OE throttle body angle by 55 degrees * Available in natural or black powdercoat finish
Not Yet Reviewed
$927.95
$834.95
On Sale
Edelbrock Performer intake manifolds are low-rise, dual-plane designs with patented runner tuning and a 180 degree firing order that you won't find with the competition. This combination boosts torque over a wide rpm range, from idle to 5,500 rpm. These manifolds also deliver improved throttle response over stock intakes and are available in both EGR and non-EGR style.
( 570 )
$919.95
On Sale
Our Summit Racing™ high performance intake combos are a great way to build horsepower and save money doing it. These systems are available in single or dual 4-barrel styles and you can take your pick of a variety of intakes. We also included carb studs and all of the intake gaskets you'll need to finish the job.
Not Yet Reviewed
$980.51
$892.43
Trick Flow® R-Series EFI Intake Manifolds deliver a perfect balance of airflow distribution and velocity. The result is excellent low-end torque and superior horsepower. The manifolds are available in kits with a natural finish aluminum lower manifold and an aluminum upper plenum in your choice of silver powdercoat, black powdercoat, and natural finishes. These manifold kits are designed for use on non-EGR engines. Manifolds for 5.0L engines with a 75mm throttle body inlet produce power in the 2,500-7,250 RPM range. Manifolds for 90mm throttle body applications produce power in the 3,000-7,750 RPM range. Additional features: *Large cross-section with 12.000 in. runners *Overall height to the upper manifold flange is 11.000 in. *Overall height to the lower manifold flange is 4.625 in. *2.000 in. x 1.200 in. port size at head *2.380 in. x 1.380 in. port size at mating flange The upper plenums and lower manifold are also available separately.
( 1 )
$859.99
The Trinity Series intake manifolds is BTR's latest offering in high-quality cast aluminum intake manifolds for LS7 engines. Their short runner, 3-piece design allows for the ultimate in application flexibility and is similar in concept to billet intakes costing thousands more. Optimum operating range is 6000-8500 rpm and is primarily intended to bridge the gap between N/A and Boosted applications. These intake manifolds utilize the high LT1 throttle body position and accepts DBW or cabled throttle bodies, yet will fit in the tight confines of the C7, C6, C5 Corvette, as well as the popular F-body platforms. BTR Trinity Series intake manifolds come semi-assembled and includes all hardware required to bolt it on. Additional features: * Available in choice of silver or black satin texture powdercoat finishes * Design incorporates two runners and an interchangeable plenum * Both the port mouth radius and the port match are CNC-machined * Seal is generated by eight entrapped O-rings at the runner/plenum interface and is clamped by M6 stainless steel socket head cap screws * Port seals are achieved SAE O-rings seated in a dovetailed O-ring groove * Incorporates two ports on the side of the throttle body boss and on the rear * Runners and plenums can be purchased separately
( 1 )
$939.99
—
$999.99
Holley Ford 351W Hi-Ram EFI intake manifold bases feature runner lengths and tapered cross sections designed to perform well for a wide range of engine combinations. The Holley engineering team also redesigned the water crossover passage to allow room for distributor phasing. Aggressive, bold, race–bred styling will make bad intentions clear for drag race, muscle car, marine, off–road, sand rails, pulling trucks, track, street rod applications and more! Features include: * Cast aluminum construction * The 351W manifold is available to work with 95mm or 105mm GM LS throttle bodies * EFI fuel rails are machined for -8AN O-ring fittings with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system * Plenum top gasket-type--3/32 in. round O-ring cord * Manifold is designed for a 9.5 in. deck height * Requires the use of Holley EFI dual sync distributor
Not Yet Reviewed
$949.95
—
$999.95
Edelbrock Performer RPM dual-quad Air-Gap intake manifolds are designed to give your ride classic hot rod looks with modern-day performance. These manifolds stand just 1 5/8 in. taller than the original Edelbrock low-profile C-26 intakes and offer superior performance improvements in the 1,500-6,500 rpm range. The large runners feature Edelbrock's unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge. These aluminum dual-quad intake manifolds are available in your choice of natural or the popular EnduraShine finishes.
( 21 )
$845.95
On Sale
Holley EFI Coyote Hi-Ram intake manifolds are designed to fit stock bolt pattern OE heads found on Ford Coyotes and related engine families, such as Voodoo and Predators. These kits include fuel rails for use with OEM-type fuel injectors and clips, mounting hardware, and O-ring gaskets. Offered in black and natural as-cast finishes, the manifolds have a 9.20 in. runner length and are designed to improve the mid to high RPM powerband. The aggressively designed Hi-Ram is constructed in a two-piece design to accommodate for air to water intercoolers and feature up to 20 percent more plenum volume versus Ultra Lo Rams. This manifold design is only offered in an oval throttle body configuration. Product features: * As-cast aluminum construction: more durable for boosted applications, can be welded for modifications * Modular design: accessible runner entries for porting, allows accessories like intercoolers and nitrous plates * Refined port design with streamlined injector boss for reduced turbulence without loss of flow area * Allows a variety of throttle valves, including large monoblade, 2015-20 GT350, 2007-14 GT500, 2019-23 GT500, GM LS 4-bolt, 2011-23 Ford Mustang GT (with optional adapter 717-18) * Fuel rails with -8 AN ports and dual 1/8 NPT accessory ports for gauges or Gen 3 direct injection fuel line hookup * Two 1/8 NPT ports on all manifolds. Two 3/8 NPT ports on all manifolds
( 1 )
$899.95
—
$927.95
$799.95
—
$834.95
On Sale
Holley SBF Hi-Ram EFI intake manifolds with side-mount tops are available for the 8.2 in. or 9.5 in. SBF Ford applications, and come with either a 95mm or 105mm Ford 5.0L throttle body flange side-mount top. The runner length and tapered cross-section design will perform well for a wide range of engine configurations. Holley's engineering team redesigned the water crossover passage to allow room for distributor phasing. The SBF Hi-Ram EFI intake manifolds have aggressive, bold, race-bred styling that's perfect for drag race, muscle car, off-road, pulling trucks, street rod applications, and more! Additional features and specs include: * Cast aluminum construction with satin silver finish * Designed for side-mounted throttle bodies (Ford 5.0L throttle body fitment) * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system; they come standard with EFI Hi-Ram kits * Plenum top gasket type: 3/32 in. round O-ring cord * Allows room for designing boosted applications * A low-profile distributor will be needed when using this manifold
Not Yet Reviewed
$1,299.95
$844.95
On Sale
Holley EFI Coyote Ultra Lo-Ram intake manifolds are designed to fit stock bolt pattern OE heads found on the 2011-23 Ford 5.0 Coyotes and related engine families, such as Voodoo and Predators. These kits include fuel rails for use with OEM-type fuel injectors and clips, mounting hardware, and O-ring gaskets. Offered in black and natural as-cast finish, the manifolds have a 9.20 in. runner length and are designed to improve the mid to high RPM powerband. The Ultra Lo-Ram provides an additional 19.4mm front and 42.6mm rear clearance compared to the Ford Performance Cobra Jet manifold—plus clears 2015-23 Mustang factory hoods. They're offered in both round and oval throttle body configurations, with replacement front inlets for easy interchangeability. The oval inlet can accommodate up to a 150 x 66mm single throttle body and 93mm on the round variant. Round inlets include standard mounting provisions for GT350, GT500, and LS 4-bolt throttle bodies. 2011-23 GT throttle bodies can be used with the optional 717-18 adapter. (NOTE: Coyote Ultra Lo-Ram intake manifolds are available with the base only, no top included, if desired. See "Intake Section Included" tabs.) Product features: * As-cast aluminum construction: more durable for boosted applications, can be welded for modifications * Modular design: accessible runner entries for porting, allows accessories like intercoolers and nitrous plates * 300-911 and 300-912 Ultra Lo-Ram will fit under stock hood with stock engine mounts in 2015-23 Mustang * Refined port design with streamlined injector boss for reduced turbulence without loss of flow area * Allows a variety of throttle valves, including large monoblade, 2015-20 GT350, 2007-14 GT500, 2019-23 GT500, GM LS 4-bolt, 2011-23 Ford Mustang GT (with optional adapter PN 717-18) * Fuel rails with -8 AN ports and dual 1/8 NPT accessory ports for gauges or Gen 3 direct injection fuel line hookup
( 1 )
$924.95
—
$949.95
$799.95
—
$853.95
On Sale
Edelbrock Performer RPM Air-Gap intake manifolds incorporate race-winning technology that's been used on Victor Series competition intakes for years. The open air space from the Air-Gap design separates the runners from the heat of the lifter-valley cover. So, the air/fuel mixture stays cooler all the way to the heads, which produces a denser charge for more power. Runners are tuned to move the power band 1,000 rpm higher than Performer Air-Gap manifolds, from idle to 5,500 rpm up to 1,500 to 6,500 rpm.
( 441 )
$811.95
On Sale
These Performer RPM FE intake manifolds from Edelbrock are designed for high-performance street Ford FE V8s with standard low/medium-rise or Edelbrock Performer RPM FE heads. Their dual-plane constant cross-sectional area design builds low and mid-range acceleration, while optimized runner paths make top-end horsepower. These manifolds have a provision for adding the PCV or breather flange at the rear, and no exhaust crossover passage.
( 37 )
$865.95
Ford Performance Parts 7.3L Super Duty low-profile intake manifolds offer better hood clearance with a straight-out inlet that will fit under an S550, and deliver an increase in horsepower and torque over the stock Godzilla manifold. Built with the latest technologies, the "plug-and-play" manifolds are easy swaps for stock units, they are lightweight, and safe for boost, nitrous, or pretty much any application. Ford Performance Parts 7.3L low-profile intake manifolds utilize the 92mm GT500 throttle body (not included) and custom calibration is required. They are topped with a removable, branded Ford performance plaque.
Not Yet Reviewed
$942.99
On Sale
Holley Sniper EFI fabricated intake manifolds are budget-friendly and performance laden! These durable Holley hi-ram manifolds feature 3mm (1/8 in.) thick T-6061 sheet aluminum construction with 100 percent TIG welds. The EFI versions have 92mm or 102mm throttle body openings, as well as runners with tapered tops to increase velocity and evenly distribute airflow. They also include 3/8 in. fuel rail kits and, of course, are branded with the Holley Sniper EFI logo. Budget and performance go hand-in-hand when it comes from Holley in the form of their Sniper EFI fabricated intakes. Order the model and options recommended for your make/engine application.
( 17 )
$826.95
—
$849.95
On Sale
Edelbrock introduces the all-new XTS manifold for the Ford 7.3L Godzilla engine. These intake manifolds feature shorter-than-stock tapered runners tuned for high-RPM gains in engine swap applications. Finished in a highly attractive black powdercoat, the XTS is designed of lightweight, durable sheetmetal. The flanges are of billet construction for strength and consistent sealing with the heads. A horizontal throttle-body mount solves one of the most common swap fitment issues of intake air routing. All standard vacuum takeoff ports are found on the rear of the manifold, and they come complete with the mounting and vacuum takeoff hardware. Additional notes: * Horizontal throttle body positioning makes inlet plumbing engine swap vehicles very easy * Short tapered runners provide significant high RPM gains, especially when matched with a Comp Cams Stage 3 Godzilla camshaft * Two 1/8 and two 1/4 NPT bosses for extra vacuum takeoff points * Team up the XTS manifold (P/N 7483) with a FAST 102mm throttle body (P/N 54106) and COMP Stage 3 camshaft (P/N 405-205-17) to create a 637 hp beast ready to swap into your favorite ride
Not Yet Reviewed
$1,045.95
$836.76
Offenhauser dual carburetor intake manifolds mount two carburetors on branched intakes, with a look that's straight from the early days of hot rodding. They're available for a number of applications to fit your speed demon needs.
( 8 )
$750.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
