Availability
Replace your slow, unreliable vacuum or electric front axle engagement system with one of these 4x4 Posi-Lok cable activated systems. The Posi-Lok systems give you direct control of your front axle right from your cab, so they will engage every time. They have a short 1 in. throw to make shifting on the fly easy, and as an added bonus, a 2WD low-range to give you the rear-wheel torque of 4-LO, and the bind-free steering action of 2-HI.
( 332 )
$174.95
Spicer Drivetrain Products front axle shafts feature an increased U-joint size that provides 25 percent higher yield strength than original U-joints. They offer unparalleled strength and longer life—the outer stub is re-engineered for added strength; improved snap ring retention reduces shock load failures; and material has been removed from the body and added to the yoke ears (to equalize deflection through the yoke and reduce bearing cap spinning). The axles are made from durable steel, with a micro-alloy improving their strength and a statistically controlled heat treatment ensuring proper hardness. Order the replacement model designed for your vehicle application.
( 129 )
$94.99
—
$1,949.99
4x4 Posi-Lok Perm-Lok systems permanently engage the central axle disconnect (CAD) system and couples both front axles. Once installed, the front axles will not pull until the transfer case is engaged. They are ideally suited for fleet operators, and emergency vehicles. Plus, installation is easy and can be completed in approximately 10 minutes.
( 20 )
$94.99
Alloy USA axle lock kits affords 4WD when you need it. Your OE vacuum disconnect systems are prone to failure. These permanent replacements allow you to manually engage the front axle from inside the cab. A simple pull of the cable ensures that you will have 4WD for as long as the transfer case is engaged. Always have a backup plan with Alloy USA axle lock kits.
( 28 )
$171.99
—
$217.99
RT Off-Road mechanical axle engagement systems replace the vacuum actuator with a cable operated actuator that puts the driver in control of the engagement from inside the cab. The axle engagement is much more reliable since it is directly controlled with the cable. Kits are available for Jeeps with a lift kit up to 3 in., and for lifted applications 3 in. or higher.
( 6 )
$133.99
Yukon Gear & Axle Dana 30 disconnect block-off plates are needed when you want to remove your troublesome 4WD disconnect and convert to one-piece axles. These plates are designed to cover the hole in your axle housing left when you remove the vacuum motor. Yukon Gear & Axle Dana 30 disconnect block-off plate kits include: * Block-off plate * Block-off plate gasket * Inner axle seals
( 2 )
$43.99
—
$110.99
Spicer Drivetrain Products front axle stubs are available for a range of applications. These quality-built steel components fit both right and left sides. When you need replacements, these front axle shafts offer a premium, competitively priced option from a name you know and trust—Spicer.
( 8 )
$61.99
—
$397.99
Artec Industries JL/JT APEX front axle armor kits include everything you need to make your factory housing the strongest it can be—including APEX front axle truss, front LCA skids, and inner C-gussets. Order the armor recommended for your Jeep application. Product details: * Patent pending APEX truss peaked top design provides more rigidity than a flat top truss design * Truss is CNC precision laser-cut in-house from 1/8 in. mild steel for a lightweight yet strong solution—only 6 lbs. * Truss is CNC precision-bent in-house for a great fitment; literally drop the truss in place on the axle and it's ready to weld—no puzzle piece assembling * Designed using 3-D models directly from Dana Corp and Jeep for an amazing fit and clearances with surrounding components * 70 percent less welding needed than previous truss designs means less warping, faster turnaround, and lower costs * All long seams are bent so you don't need to spend time welding them together * APEX design continues under the OEM coil buckets for complete end-to-end axle reinforcement—an industry first * Dimpled holes provide weight reduction, rigidity, and strength * Contours both the cast steel differential and FAD (front axle disconnect) and can be welded with normal MIG welder and moderate pre-heating and post-heating * Provides worry-free wheeling of up to 40 in. tires on stock JL axles * Bridges the front axle disconnect (FAD/CAD), shown to be one of the weakest sections of the front axle * Low-profile design doesn't go over differential and allows usage in vehicles with only slight lift * Front LCA skids and optional JL Shield are made from 1/4 in. steel * Inner C-gussets are made from 3/16 in. steel
Not Yet Reviewed
$236.81
Artec Industries Ford SuperDuty front axle trusses deliver a revolutionary low-profile design. They take the years of race and recreational abuse of Artec's first generation of trusses and add additional strength and functionality. Their key feature is how the truss top now bends around the differential for a better fit and clearance, making them ideal for vehicles needing more up-travel or for those building low center of gravity vehicles. The overall low-profile design means your axle is stronger, sleeker, easier to fit into any vehicle, and less likely to interfere with vehicle components. Features: * 3/8 in. thick mild steel truss top and 1/4 in. mild steel ram mount and gussets * Precision CNC-cut and bent for great fitment * Truss has super low-profile allowing better clearance for oil pans * Truss spans entire length of axle for complete reinforcement of the axle tubes * Truss is reinforced using interlocked 1/4 in. thick gussets for maximum strength and easy assembly * Main interlocking gussets are wider than Gen1 trusses adding overall strength to truss * Internal gussets conform tightly to the contours of the differential allowing you to weld to it for additional strength and rigidity * Truss is clearanced for differential breather tube
Not Yet Reviewed
$319.99
When you need only the strongest parts to keep it together, beef up your front-end with Artec Industries Dana 60 Front Hydro Ram mounts. Their overall low-profile design means that your axle is stronger, sleeker, easier to fit, and less likely to interfere with rocks or other parts of your vehicle. The mounts' unique design places your ram in its most effective and strongest location—close to the axle centerline, not high above it—and yet they protect it from the rocks. The Ram mounts extend to the end of the axle tube, providing reinforcement to the axle itself against bending and shearing. They're designed to take serious abuse and protect your steering. Artec Industries Dana 60 Front Hydro Ram mounts are available for fitment on a variety of applications, from 1960 and up. Product features: * 1/4 in. mild steel ram mounts and gussets are precision CNC-cut and bent for great fitment and reinforcement against damage * Ram mounts and gussets feature drainage holes for easy cleaning and reduced weight * Mounts double as an axle skid plate, offering protection for your ram and tie rods—and span the length of the axle tube for more reinforcement against bending and shearing * An additional 1/4 in. thick bolt-on skid plate in front of the differential allows easy removal of gears; it's bolted using included countersunk bolts, which don't get hung up on obstacles and hold up against trail damage * These kits require general welding and fabrication skills
( 2 )
$369.99
—
$429.99
Spidertrax Off-Road's all-new 1480 40 spline front axle stubs are a reinvention of their already proven 35 spline stub shafts. Manufactured from billet 300M aerospace material with an integrated positive locking design—all while achieving 50 degrees of steering—they're the next best thing in stub shaft technology… and the last stub shafts you'll ever need. These 1480 40 spline stub shafts are designed to work with 60 style U-joints and Spidertrax 40 spline Ultimate Unit Bearings. * Aerospace Quality: Spidertrax follows the strictest AMS Aerospace standards for their heat treatment, complete with double tempering, snap tempering, and cryogenic treatment procedures. Parts are sampled to ensure proper grain structure is achieved up to 0.0003 in. from the surface; that's a depth 1/10 the thickness of a human hair! In summary, you're getting the best material and the best heat treatment on the market. * Locked: Turning 40 degrees is impressive, but Spidertrax axle shafts can turn 50 degrees. Engineers achieved this by positively locking the shaft to the Ultimate Unit Bearing with a billet aluminum cap and cap screw. Keeping that stub shaft tightly secured not only helps with driveline vibration, but helps with overall strength of shaft and U-joint. * 40 Splined: Each stub shaft is 40 splined—a size that makes perfect sense, especially when running properly paired inner axle shafts. When sized with the same shaft diameter as inner shafts, stub shafts end up taking the full punishment in your front-end. The stub shaft should be "stronger" than an inner axle because unlike an inner axle, stub shafts have little room to twist, making them more prone to failure. An added bonus: with many drivers running 40 splined rear Ultimate Unit Bearings, having the same unit bearing up front makes for better serviceability and part simplicity.
Not Yet Reviewed
$1,299.00
Alloy USA chromoly front axle shaft kits use high-tensile strength 4340 chromoly that is heat-treated twice, making them up to 30 percent stronger than stock. Keep your truck going on the trail, rocks, or mud with Alloy USA front axles.
( 4 )
$49.50
—
$1,099.99
Artec Industries XJ front axle trusses beef up your axles with options. These trusses are presented with three upper control arm choices—truss only, truss with Daystar bushings, or truss with Currie Johnny Joints. All are heavy-duty, lightweight support systems that strengthen your axle against serious abuse with 1/4 in. thick mild steel truss tops and 10-gauge gusseting. Artec precision-cut and formed components of this setup ensure a hassle-free installation. Reinforce your axle's performance with solid options from Artec Industries XJ front axle trusses. Artec XJ axle trusses are available as: * Truss only—no bushings/joints/keyed tabs included * Truss with Daystar bushings—includes bushing, inner sleeve, and thrust washer for driver side; and bushing, weldable outer sleeve, inner sleeve, and two keyed tabs for passenger side * Truss with Currie Johnny Joints—includes 2.0 in. press-in machined Johnny Joint, 2.0 in. weldable Johnny Joint, two keyed tabs for passenger side, and greasable bolts for both joints
( 2 )
$142.53
—
$329.99
Keep your 4WD working properly with these Standard Motor Products 4WD actuators. They are designed to be direct replacements and meet or exceed OEM specifications. They come available for a variety of applications.
( 4 )
$21.99
—
$451.99
Alloy USA front axle shafts will uphold your hardcore adventures with strong, premium alloy steel, offering great durability to keep you moving with confidence. These terrain-tested axles are engineered and manufactured using high-tensile strength 4340 chromoly that's heat-treated, tempered, induction-hardened, and CNC-machined and anodized to produce stronger-than-stock axles. Horsepower is useless if you can't get it to the ground. Let Alloy USA front axle shafts help you get dialed-in for the maximum power connection, both on the road and off.
( 1 )
$125.99
—
$312.99
In late 1980s to mid 90s, Jeep used a vacuum actuator to shift the transfer case and corresponding front axles in and out of 2WD, and high or low 4WD. Crown Automotive 4WD front axle actuators will replace faulty vacuum switches to improve your vehicle's get-up-and-go, no matter the terrain.
( 8 )
$33.99
—
$174.99
Trail-Gear Rock Assault front axle housings give you clearance to go where you want and the muscle to do it! Their strength comes from heavy-duty, press-formed, 1/4 in. plate steel center sections; 1/2 in. plate steel differential mounting surfaces; 5/16 in. thick 1020 DOM axle tubes; and forged 1035 steel knuckle balls. Trail-Gear's knuckle balls are stronger than stock, so there are no worries of them becoming closed or bent. And, the thicker differential mounting surface ensures that the studs cannot pull out, even under heavy loads. Trail-Gear's design—offset tubes and shaved center section—provides you with added clearance to climb the high country. Plus, since housings are precision-aligned with computer imaging, you can rest assured they're 100 percent straight and true. You have a choice of bare tubes, or with spring perches installed—or 3-link ready with a panhard bracket included. You're equipped to attack any terrain with Trail-Gear Rock Assault front axle housings.
( 1 )
$1,499.99
—
$1,599.99
Artec Industries JK APEX front axle ultimate armor kits furnish everything you need to make your axle the strongest it can be. These packages include an APEX front axle truss, heavy-duty front LCA brackets, heavy-duty shock brackets, inner C-gussets, and APEX heavy-duty tracbar bracket. Armor kits are available for a variety of specific Jeep applications, in both stock and raised track bar height models. How is the ultimate armor kit better than the regular armor kit? This kit includes entire replacement LCA brackets and shock brackets, whereas the regular armor kit just adds a skid plate to the factory LCA brackets. Product details: * Patent pending APEX truss peaked top design provides more rigidity than a flat top truss design * Truss is CNC precision laser-cut in-house from 1/8 in. mild steel for a lightweight yet strong solution—only 7 lbs. * Truss is CNC precision-bent in-house for a great fitment; literally drop the truss in place on the axle and it's ready to weld—no puzzle piece assembling * Designed using 3-D models directly from Dana Corp and Jeep for an amazing fit and clearances with surrounding components * 70 percent less welding needed than previous truss designs means less warping, faster turnaround, and lower costs * All long seams are bent so you don't need to spend time welding them together * APEX design continues under the OEM coil buckets for complete end-to-end axle reinforcement—an industry first * Dimpled holes provide weight reduction, rigidity, and strength * Contours to the cast steel differential and can be welded with normal MIG welder and moderate pre-heating and post-heating * Provides worry-free wheeling of up to 37 in. tires on stock JK axles * Truss strengthens the weakest sections of the axle—under the coil perches, around the control arm brackets, and where the tube enters the casting * Low-profile design doesn't go over differential and allows usage in vehicles with only slight lift * Front LCA brackets, shock brackets, inner C-gussets, and HD tracbar brackets are made from 1/4 in. steel * Gussets and brackets strengthen or replace weak components of the axle that are prone to failure
Not Yet Reviewed
$406.99
—
$439.99
Artec Industries JK APEX front axle trusses introduce a whole new level of cost savings, strength, weight savings, simplicity of installation, precision fitment, and complete axle protection never before seen in the industry. The key feature that sets the APEX truss apart is its unique peaked shape top which provides extra rigidity to the whole truss, while allowing both a reduction in weight (vs. using a thicker material top) and eliminating long weld seams. Previous versions with long weld seams have led to extra weld warping of the axle, longer install times, and can be inconsistent. This peaked structure not only applies to the axle tube between the coil perches, but extends underneath the coil perches as well—forming a complete truss from end to end of the axle, an industry first in an OEM axle application. The JK APEX truss has been tested and proved to hold up to both extreme applications and daily driving. Product details: * Patent pending APEX truss peaked top design provides more rigidity than a flat top truss design * Truss is CNC precision laser-cut in-house from 1/8 in. mild steel for a lightweight yet strong solution—only 7 lbs. * Truss is CNC precision-bent in-house for a great fitment; literally drop the truss in place on the axle and it's ready to weld—no puzzle piece assembling * Designed using 3-D models directly from Dana Corp and Jeep for an amazing fit and clearances with surrounding components * 70 percent less welding needed than previous truss designs means less warping, faster turnaround, and lower costs * All long seams are bent so you don't need to spend time welding them together * APEX design continues under the OEM coil buckets for complete end-to-end axle reinforcement—an industry first * Dimpled holes provide weight reduction, rigidity, and strength * Contours to the cast steel differential and can be welded with normal MIG welder and moderate pre-heating and post-heating * Provides worry-free wheeling of up to 37 in. tires on stock JK axles * Truss strengthens the weakest sections of the axle—under the coil perches, around the control arm brackets, and where the tube enters the casting * Low-profile design doesn't go over differential and allows usage in vehicles with only slight lift
Not Yet Reviewed
$110.73
—
$120.99
Artec Industries APEX front axle trusses feature a unique peak-shaped top which provides extra rigidity to the whole truss. This allows both a reduction in weight and elimination of long weld seams which can lead to extra weld warping, longer install times, and inconsistency. This peaked structure also applies to the axle tube between the coil perches and extends underneath them, forming a complete truss from end-to-end of the axle. Despite its lighter weight (only 6 lbs.), this design has been proven to hold up to both extreme applications and daily driving. Want easy insurance that your factory Jeep axle can take more abuse than intended? Artec Industries APEX front axle truss kits provide it! Features, items, and specs: * Intended for use on vehicles with minor lifts and at least 1/2 in. bump stop extensions * CNC precision laser-cut in-house from 1/8 in. mild steel * CNC precision-bent in-house for a great fitment (drop in place on axle and it's ready to weld—no puzzle piece assembling; some grinding may be required—every axle varies slightly) * Designed using 3-D models directly from Dana Corp and Jeep for an amazing fit and clearances with surrounding components * All long seams are bent—no need to weld them together * Dimpled holes provide weight reduction, rigidity, and strength * Contours both the cast steel differential and front axle disconnect (FAD) which it bridges for reinforcement; can be welded with normal MIG welder using moderate pre- and post-heating * Provides worry-free wheeling of up to 40 in. tires on stock JL axles * Low-profile design allows usage in vehicles with only slight lift
Not Yet Reviewed
$112.21
—
$324.99
When you've exceeded he limits of your Dodge 60 front axles, Artec Industries has the solution--heavy-duty trusses. Built from 3/8 in. thick mild steel truss tops with 1/4 in. mild steel ram mounts and gussets, these trusses are precision CNC-cut and bent for maximum strength. They are low-profile and span the entire length of your axle for complete reinforcement. Larger tires and aggressive driving ... maybe it's time to support your Dodge 60 front axles with trusses from Artec Industries.
Not Yet Reviewed
$359.99
Low Range Off-Road front axle truss with gusset kits get your axles off-road ready. A weak point on some vehicles is the front axle, which can be susceptible to bending or warping causing misalignment, tire wear, and premature failure of front axle components. For any off-road usage, Low Range Off-Road recommends trussing your axle with their truss and gusset kits. They are a must for anyone planning to do a spring over axle swap or aftermarket suspension and tire upgrades. The truss is notched in the center of the gusset to accommodate the factory weld on the axle. Contents and additional features: * One upper truss * Two lower knuckle ball gussets * Easy stitch weld installation * Ships raw * Available with or without Low Range "LR" logo
Not Yet Reviewed
$42.50
Artec Industries TJ front axle trusses offer options for beefing up your axles. These front axle trusses are presented in two axle models and three upper control arm options. They're heavy-duty, lightweight support systems that strengthen your axle against serious abuse with 1/4 in. thick mild steel truss tops and 10-gauge gusseting. Artec precision-cut and formed components of this setup ensure a hassle-free installation. Reinforce your axle's performance with solid options from Artec Industries TJ front axle trusses. Axle model options: * 30 low pinion * 44 low pinion Upper control arm options: * Truss only—no bushings/joints/keyed tabs included * Truss with Daystar bushings—includes bushing, inner sleeve, and thrust washer for driver side; and bushing, weldable outer sleeve, inner sleeve, and two keyed tabs for passenger side * Truss with Currie Johnny Joints—includes 2.0 in. press-in machined Johnny Joint, 2.0 in. weldable Johnny Joint, two keyed tabs for passenger side, and greasable bolts for both joints
Not Yet Reviewed
$142.59
—
$329.99
On a mission to provide world class aftermarket automotive parts, Artec Industries front axle lower trusses are designed to reinforce the entire front axle on the Ford Super Duty F-250 and F-350. With the heavy engines on these trucks, the stock front axles have suffered from bending and even breaking under hard use. These front axle lower trusses allow maximum up-travel while only decreasing under-axle clearance slightly. In fact, there is virtually no loss of ground clearance under the differential. They are great for those who like to push the skinny pedal down and get some air at the dunes or in the mud. The whole design is CNC cut and formed to fit great on your axle, so little-to-no grinding or modification required, providing a straightforward installation. Features include: * 1/4 in. thick mild steel is precision CNC designed, cut, and bent for great fitment * No loss of ground clearance under the cast differential * Triangular shape provides increased structural rigidity and helps axle skid over obstacles * Truss spans the entire length of axle, inner c to inner c, completely reinforcing the axle tubes * Comes in five separate pieces for compact shipping and easier installation
Not Yet Reviewed
$120.99
—
$229.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
