Availability
RCV Performance custom ultimate CV axles replace your Ford Dana or GM Dana 60 U-joint axle shafts with a high-strength constant velocity design. Upgraded 300M CV axle options are also available. The kits are designed for custom length inners. These axles are just as tough at a straight angle as they are at extreme angles where U-joints are weakest. Ultimate CV axles also eliminate U-joint binding to allow smooth transfer power to the ground. Even if you have big tires and big power, there are no worries! Additional details: * Ultimate CV Axles are low maintenance and operate with a smoothness you can feel, whether off-road or on the street * Axle sets RCV-CVJ60-FP and RCV-CVJ60-GMP include 4340 right and left CV axle shafts with 300M inner race, 300M outer stubs, SST seals and installation tool, and RCV synthetic moly grease * Axle sets RCV-CVJ60M-FP and RCV-CVJ60M-GMP include 300M right and left CV axle shafts with 300M CVs, 300M outer stubs, SST seals and installation tool, and RCV synthetic moly grease * Black oxide coating is standard * The Ford Dana and GM Dana 60 CVs are able to accept a 35-spline inner axle
Not Yet Reviewed
$2,899.95
—
$4,195.95
RCV Performance custom Big Bell CV axles are the ultimate solution designed to fit 2005+ Ford F450 and F550 Super Duty applications, as well as big knuckles like the Reid Super Kingpin knuckles for Ford Super-60 unit bearings. The Big Bell CVs are RCV's 2.5 ton Rockwell CVs, but the outer stub is designed to fit directly to the large 32-spline 2005+ Ford Dana 60 "Super-60" unit bearing. This eliminates the need for a lock-out or drive flange, increasing strength and reliability. These kits are designed for custom axles. The Big Bell CV is able to accept a 40 or 47 spline inner axle.
Not Yet Reviewed
$4,195.95
RAM truck pulling clutch kits are custom-assembled for your specific application. These units feature a heavy-gauge steel cover with welded spring guides and a steel pressure ring. Flywheels are available in 30 or 40 lb. weights, as well as in billet aluminum. The clutches can be set up with either 5135 or 5191 compound iron discs with 1 to 10 splines. Single disc slipper-style clutches can be used with engines producing up to 800 hp, or where very limited slipping is desired. These clutches utilize the same quality components as the RAM dual disc pulling clutches. These units can be assembled with your choice of sintered iron disc materials and flywheel weights. Dual disc clutches will allow a more controlled slip as the vehicle comes out, without severe wear or every-round maintenance. Dual disc clutches are built to fit different stock depths or deep bellhousings.
( 2 )
$2,300.00
Strange Engineering has developed the iconic Ford 9 in. rear axle into an extensive line of parts and complete HD Pro aluminum custom order assemblies that take advantage of the strengths of the original, while improving on strength, performance, and flexibility. These axles consist of forged aluminum pinion supports, with a lightweight steel spool or clutch posi unit and your choice of gear ratio in a standard gear, fully assembled with yoke. The most popular rear-end around is the Ford 9 inch unit; it is used by restorers, street rodders, and racers alike, regardless of what brand of car they're restoring.
( 2 )
$2,021.99
Strange aluminum custom order dropship ultra center sections are all about performance. Strange Engineering has over 40 years of rear-end assembly experience depended upon by world champions from street to top fuel, so you know these units are designed to perform. Available in a variety of applications and setups for everyone, they are shipped fully assembled in protective transport cases. Requires gear ratio and axle spline before ordering. Please call us at 1-800-230-3030 for further information.
Not Yet Reviewed
$2,498.99
—
$3,275.99
Hughes Performance Street and Strip transmissions are made tough enough to deliver tire-spinning shifts race after race. They include internal and external racing components, which increase strength, reliability, and torque capacity. Plus, they feature Hughes' manual/automatic valve body to provide precise manual or fully automatic shifting. Choose the transmission type best suited for your vehicle.
( 30 )
$2,049.99
—
$3,712.99
Strange bolt-in S60 rear differential assemblies are designed to fit your vehicle without any modifications. Brake kits are sold separately. Assemblies feature: * Strange-designed S60 housing cast from nodular iron * Large nodular iron bearing caps * One-piece center casting for enhanced rigidity * Adjuster nuts for precise and easy setup * Fully welded tubes * Strange ring and pinion gear * 35-spline axles
( 4 )
$2,594.99
—
$3,371.99
These Strange 12-bolt F-body rear-end assemblies are designed to replace the entire rear-end in your F-body Camaro or Firebird. They feature the following components: * Strange designed 12-bolt case with torque arm provision * Premium nodular iron casting * Choice of differential carrier * 33 or 35 spline Pro Race Axles * Pro gear set * Choice of gear ratio * Fully welded axle tubes * S-series yoke with u-joint * Accepts 1993-97 or 1998-2002 disc or drum brakes (sold separately) * Chrome rear-end cover
Not Yet Reviewed
$3,424.99
American Powertrain ProFit Tremec TKX manual transmissions and installation kits put the power to the pavement with unmatched durability and versatility. Tremec has normally sourced their aftermarket transmissions from the OE side, such as the Magnum T-56 and the T-5, but this new design is made from the ground up as a strictly aftermarket transmission. Designed to fit classic muscle cars and customs, the TKX has a tighter, more streamlined case, and features 600 lbs.-ft. of torque capacity and are capable of engines speeds of 8,000 rpm with shifts at 7,500 rpm. The compact design provides clearance in most transmission tunnels without floor modifications, while case strength has increased from previous models with the new 3-piece aluminum housing and gaskets at all flanges simplifies installation and eliminates fluid leaks. Additional features include: * Designed with your specific vehicle application in mind * Available with multiple gear ratio configurations for compatibility for multiple applications with three shifter locations * Multi-cone synchronizers and synchronizer rings are made of sintered bronze and carbon for superior shifts * All gears are supported by caged needle bearings to reduce end play * Gears and shafts are made from ASTM 4615 grade steel and provide increased torque carrying capacity * TKX manual transmissions have 31-spline output shafts for added strength, built-in reverse light switches, and cruise control safety switches * The TKX also has separate GM and Ford case patterns and input configurations—with integrated GM and Ford transmission mount patterns * Installation kits include a driveshaft slip yoke made from cryogenically hardened steel, a polyurethane transmission mount, a steel roller pilot bearing, and a reverse light wiring harness
( 1 )
$3,995.95
—
$4,559.95
Redesigned and strengthened, Reid Racing Super Hydra 400 transmission cases address weaknesses and add features that improve every aspect of the Turbo 400. They build their Super Hydra 400 cases with full 360 degree internal case "lugs" that retain the center support and pressure plate. Not only are they lightweight and offer minimal drag, but their abuse tolerance has been kicked up several notches to handle high-horsepower levels without ending up with a ruined transmission! A direct replacement for the GM case, Reid cases use an incredibly expensive permanent mold casting technique to increase the case wall thickness, making it sufficient to pass SFI 4.1 certifications without the need for any external shields or internal liners. Super Hydra 400s are massively tough, ductile, and leak-free—with the strength to handle rock crawling, as well as desert or short-course truck racing. Their modular, 2-piece design allows them to be used with all popular engines by simply changing bolt-on Superglide bellhousings. Reid Racing Super Hydra 400 transmission cases are offered in drag/street and off-road versions, each with features geared specifically for those applications. Features: * Speedometer and governor provisions * Improved billet steel pressure plate * Oversized snap ring * Longer band anchor pins captured by oversize bosses * Additional dipstick hole on driver side * Multiple external pressure taps allow for monitoring of circuit pressures * Accept all style oil pumps, including 8-bolt and vari-pitch designs * Heli-coiled bellhousing and oil pump threads * Pre-machined to fit larger custom planetary gear carriers Off-road also includes: * Pre-machined side oil feed feature for 4L80-E center support * Front band anchor tapped for custom ARP anchor bolt (supplied) * Pre-machined bosses for input and output speed sensors * Un-machined speedometer boss for maximized 4x4 transfer case load support * Oil line ports machined for -AN fittings * Pre-machined with additional stud/nut clearance for Advance Adapters transfer case adapters * Available with a 4L80-E size pressure plate
( 4 )
$2,148.99
—
$2,282.99
Building transmissions since 1963, Bowler believes in detail, and each of their Tru-Street automatic transmissions are fully remanufactured (not "rebuilt") by one qualified technician, dyno tested, and then custom packaged for safe shipping. The Tru-Street Series includes torque converter and may include other components, as well. Choose the one you prefer.
Not Yet Reviewed
$4,259.99
—
$4,651.99
If you have chosen a Ridetech 4-link system to improve the ride quality, handling, and braking of your classic muscle car, the next purchase should be a Ridetech Ford 9 in. housing and axle package with integrated 4-link and sway bar brackets. These stock 4-link axle assemblies allow for the easiest installation of your 4-link system. The 9 in. Ford housings are great foundations for putting torque to the pavement. They feature a webbed center section, internal gussets, thick wall tubes, and billet steel flanges (new-style Big Bearing/Torino). The pinion is offset 1/2 in. and the axle flange is offset 2 1/2 in. Ridetech stock housing and axle packages are offered in two axle lengths and available raw or with a black powdercoat finish. Select the proper length and preferred finish for your project. Features and benefits: * Webbed center section with internal gusseting for added strength * 3 in. diameter, 1/4 in. thick wall tubes * 31-spline heat-treated 1541H custom alloy axles * High-quality Timken tapered bearings on axle as standard * Drain plug and jack pad * High-quality Grade 8 installation hardware--housing studs, T-bolts, nuts, and washers * 3rd member studs are pre-installed and ready to accept a third member
Not Yet Reviewed
$2,175.00
—
$2,275.00
Factory driveshafts are made from a smaller tube (there are 2 different types) and will flex and bend during hard acceleration, causing the rubber drives to wear out prematurely. The Driveshaft Shop torque tube driveshafts are made from 3 x .125 wall 6061 T-6 aluminum and uses The Driveshaft's own custom machined ends. This ensures that the shaft will not distort or break like the factory units, and offer units rated up to 1000 hp. Choose the driveshaft designed for your vehicle.
( 4 )
$2,020.37
—
$3,058.43
RevMax offers Stage 5 Billet Quad Clutch Insignia Converters for a variety of applications, including many Ford trucks from 2011 and up. These torque converters are designed for those who have heavily modified engines or for those who tow heavy weights. They're the culmination of over two years R&D. Each converter features four lockup clutches and retains the factory damper assembly to provide extremely smooth converter apply. Even with twice the holding capacity of a stock converter, most RevMax customers rate these quad units as smooth as their original stock dual disc. RevMax Stage 5 converters have no horsepower or torque limitations. Additional details: * CNC-machined billet one-piece front cover * Raybestos or Alto, high performance quad disc lockup friction * RevMax proprietary CNC-machined stator designs * Billet bearing cap * Dual Torrington Bearing stator design * 4140 flanged impeller hub * 4140 hardened turbine hub * Furnace brazed impeller * TIG-welded brazed turbine * Computerized robotic welding * Precision internal clearances set to increase efficiency and improve performance * Fully pressurized and leak-tested * TCRS computerized high-speed balancing to less than 5 gram * Runout tolerances of less than .005
Not Yet Reviewed
$2,195.00
Trail-Gear offers fully built Rock Assault front and rear axles made of entirely new parts and customized to your choices. They include everything needed from hub-to-hub, and are expertly assembled by TG's master mechanics. Save yourself time, money, and the hassle of ordering each component separately and then building it yourself. You make the choices and let Trail-Gear do the assembly! Select your kit. Front and Rear Rock Assault fully built axles feature: * 5/16 in. thick, high-strength DOM axle tubes that engage 5/8 in. further into the center section and the 360-degree gusset welded around the tubes on the inside of the housing * Axle tubes have been offset above the housing centerline to allow the inner axles to ride near the bottom of the axle tubes rather than in the center * Increase of 3/8 in. ground clearance under the axle tubing * Heavy-duty, press-formed, 1/4 in. plate steel center section shell is specially shaped to ensure a minimum of 3/4 in. additional clearance under the differential * Differential mounting surface is made from 1/2 in. plate steel Rear axle kit contents and features: * Rock Assault axle housing * Complete rear disc brake kit * Chromoly axle shafts * Bearing pockets * Rear axle bearing service kit * All necessary nuts and studs * Outer offset flanges are made from 4130 chromoly to prevent distortion or bending * Housings are precision aligned using start-of-the-art, 3D digital imaging equipment * Customize each axle to exactly what you need with your choice of: -- Axle width -- Differential Front axle kit contents and features: * Toyota Rock Assault axle housing * Upgraded Longfield 30-spline Birfields * 30-spline chromoly axle shafts * Fully Loaded Six-Shooter knuckle kit * Chromoly spindles * Upgraded brake rotors and calipers * Heavy-duty tie rod and drag link * Trail-Gear's upgraded Trail Safe seals * Super Metal knuckle studs * All necessary nuts, bolts and seals * 59 in. from WMS to WMS * Knuckle balls are forged from 1035 steel * Customize each axle to exactly what you need with your choice of: -- Axle width -- Axle offset -- Differential -- Hubs or flanges
Not Yet Reviewed
$4,599.99
These Chevrolet Performance automatic transmission controllers include the wiring harness, controller, software, and laptop hookup. They are designed to allow for the use of electronically controlled transmissions in early model vehicles. Chevrolet Performance automatic transmission controllers are fully programmable for upshift, downshift, part throttle and wide-open shifts, and shift firmness. They come preprogrammed--just enter your rear tire diameter and rear axle ratio and go, or create your own custom shift characteristics. Chevrolet Performance automatic transmission controllers were originally developed by GM Racing for off-road truck racing. They have the ability to record and graph drag racing data like time, speed, shift point, engine rpm, and more.
( 1 )
$2,100.48
If you have chosen a Ridetech 4-link system to improve the ride quality, handling, and braking of your classic muscle car, the next purchase should be a Ridetech Ford 9 in. housing and axle package with integrated 4-link and sway bar brackets. These narrowed 4-link axle assemblies allow for the easiest installation of your 4-link system. The 9 in. Ford housings are great foundations for putting torque to the pavement. They feature a webbed center section, internal gussets, thick wall tubes, and billet steel flanges (new-style Big Bearing/Torino). The pinion is offset 1/2 in. and the axle flange is offset 2 1/2 in. The narrowed axle widths satisfy mini-tub applications. Ridetech narrowed housing and axle packages are offered in two axle lengths and available raw or with a black powdercoat finish. Select the proper length and preferred finish for your project. Features and benefits: * Webbed center section with internal gusseting for added strength * 3 in. diameter, 1/4 in. thick wall tubes * 31-spline heat-treated 1541H custom alloy axles * High-quality Timken tapered bearings on axle as standard * Drain plug and jack pad * High-quality Grade 8 installation hardware--housing studs, T-bolts, nuts, and washers * 3rd member studs are pre-installed and ready to accept a third member
( 1 )
$2,175.00
—
$2,275.00
Hughes Performance Muscle car transmission packages are designed and built to give customers the option to choose the transmission and converter package best suited for their needs. The transmission packages come complete with everything you need—transmission, converter, transmission cooler, transmission fluid, and more. So, whether you have a radical cam in your hot rod, or need to haul or tow a heavy load, Hughes Performance offers high-quality transmission packages to match your application needs. Note: Contents of kits vary based on transmission type and your vehicle.
( 1 )
$3,750.99
—
$3,918.99
Redesigned and strengthened, Reid Racing Super 80 transmission cases address weaknesses and add features that improve every aspect of the 4L80e. They build the Super 80 cases with full 360 degree internal case "lugs" that retain the center support and pressure plate. Not only are they lightweight and offer minimal drag, but their abuse tolerance has been kicked up several notches to handle high-horsepower levels without ending up with a ruined transmission. Reid Super 80 cases are massively tough, ductile, and leak-free with the strength to handle turbocharged muscle cars, drag cars, rock crawling, and desert truck racing. Their modular, 2-piece design allows them to be used with popular engines by simply changing bolt-on Superglide bellhousings. Reid Racing Super 80 transmission cases are SFI 4.1 certified without requiring any external shields. Features: * Improved billet steel pressure plate * Oversized snap ring * Longer band anchor pins captured by oversize bosses * Multiple external pressure taps allow for monitoring of circuit pressures * Heli-coiled bellhousing and oil pump threads * Front band anchor tapped for custom ARP anchor bolt (supplied) * Input and output speed sensors--bosses are dual machined to accept freeze plugs * Oil line ports machined for -AN fittings * Pre-machined with additional stud/nut clearance for Advance Adapters transfer case adapters
( 2 )
$2,318.00
On Sale
Spicer Driveline Ultimate Dana 44 AdvanTEK crate axle assemblies offer increased strength and durability in every facet—from thicker bracket mounts to upgraded materials to beefier housing tubes. Strength, versatility, bolt-in convenience, and a rock-solid history: it all comes together harmoniously in the Ultimate Dana 44 AdvanTEK crate axle assemblies from Spicer Driveline. Order the model with the ring and pinion ratio needed for your application. Spicer Ultimate Dana 44 AdvanTEK advantages: * Aggressive nodular iron differential cover * Heat-treated high-grade SAE-4340 chromoly steel axle shaft offers superior abrasion resistance and strength, as well as uniform surface * Thicker steel bracket mounts * Upgraded U-joints outperform the competition, with Nm load ratings of 3000 (1350 Series) and 3600 (1400 Series) * Thicker tubes for added strength * Custom high-clearance housing is designed to optimize extreme off-road performance * Expanded gear ratio options to accommodate different tire sizes * Genuine Spicer AdvanTEK ring and pinion gears for greater strength * Track width is identical to OE track width * No FAD (front axle disconnect) means increased strength * Selectable E-Locker
Not Yet Reviewed
$5,699.99
$5,129.99
Ford Performance is proud to offer the latest 5-speed transmission from Tremec—the TKX-600. Capable of handling 600 lbs.-ft. of torque, they're the perfect 5-speed manual transmission choice for your custom build! Tremec TKX-600 5-speed transmissions features: * Reduced overall size - easier to package in a variety of vehicles * Improved, smoother shifting * Hybrid carbon/bronze synchronizers (7,500 rpm shift capability) * Wider, more durable gears than TKO transmission * Caged needle bearings for improved durability * 26-spline input shaft/31 spline output shaft * 1st gear = 2.87, 2nd gear = 1.89, 3rd gear = 1.28, 4th gear = 1, 5th gear = .68 * Dry weight: 99 lbs. * Fluid capacity 2.7 quarts—Tremec High Performance Manual transmission fluid or Mobil 1 Synthetic ATF is recommended * Use part number M-6392-R58 bellhousing for 302/351 engines * Use part number M-6392-M46 bellhousing for 4.6/5.0/5.2/5.4 modular engines
Not Yet Reviewed
$3,066.99
If you are already running one of QA1's 4-link suspension kits on your classic car, get ready to take your build to the next level with their custom 9 in. rear housings engineered to integrate seamlessly with your existing QA1 setup. Designed for enthusiasts looking to improve performance and durability, QA1 Narrowed Ford 9 in. rear axle housings are perfect upgrades for handling more horsepower and aggressive driving conditions. They are designed to bolt seamlessly to your QA1 4-link system, with fully formed trailing arm brackets that minimize flex under heavy loads, enhancing strength and rigidity. Whether you're increasing horsepower or seeking a more durable rear-end solution, these custom QA1 9 in. rear housings deliver the performance gains you need. Select the kit designed for your vehicle. Features: * Narrowed 2 1/2 in. per side for use with mini tubs for wider wheel and tires * Fabricated center section engineered for maximum strength and durability * Formed trailing arm brackets ensure your suspension remains rigid * Heavy-duty 3 in. O.D., 1/4 in. thick wall axle tubes provide the durability needed for high-performance applications * 31-spline 1541H alloy axles support up to 650 hp, with the housing handling up to 800 hp * Standard 5 x 4 3/4 in. bolt pattern for a wide range of wheel options * Durable semi-gloss powdercoat finish offers long-lasting protection and a clean, sleek look * Drain plug, fill plug, and jack pad come standard to make service a breeze * Includes T-bolts and housing studs for assembling axle shafts and installing third members * High-quality roller bearings for smooth operation and long-lasting reliability
Not Yet Reviewed
$2,099.95
Strange 12-bolt bolt-in rear-ends with heavy-duty posi and leaf spring mounts are custom-made to your specifications. Details: * Factory or custom widths available * Choice of housing ends and leaf spring mounts * Professionally welded and assembled * Crated to protect your investment Information required: * Factory bolt-in * Year, make, and model of vehicle * Factory / Custom width (specify) * Mounts: Single leaf / Multi leaf / Other (specify) * Type of brakes: OEM Drum / Aftermarket * If aftermarket, specify manufacturer and part number * Bolt circle and stud choice * Gear ratio Assembly includes: * 12-bolt housing with leaf spring mounts installed * 30-spline alloy axle package * 4 1/2 in., 4 3/4 in., or 5 in.″ bolt circle * Choice of press-in or screw-in stud kit * Standard gear set * Eaton HD clutch style posi * Choice of gear ratio * S-Series pinion yoke * Pinion yoke U-bolt kit * Chrome steel cover * Bottle of friction modifier (clutch units only) * Fully crated
Not Yet Reviewed
$3,033.99
If you are already running one of QA1's 4-link suspension kits on your classic car, get ready to take your build to the next level with their custom 9 in. rear housings engineered to integrate seamlessly with your existing QA1 setup. Designed for enthusiasts looking to improve performance and durability, QA1 Standard OE width Ford 9 in. rear axle housings are perfect upgrades for handling more horsepower and aggressive driving conditions. They are designed to bolt seamlessly to your QA1 4-link system, with fully formed trailing arm brackets that minimize flex under heavy loads, enhancing strength and rigidity. Whether you're increasing horsepower or seeking a more durable rear-end solution, these custom QA1 9 in. rear housings deliver the performance gains you need. Select the kit designed for your vehicle. Features: * Fabricated center section engineered for maximum strength and durability * Formed trailing arm brackets ensure your suspension remains rigid * Heavy-duty 3 in. O.D., 1/4 in. thick wall axle tubes provide the durability needed for high-performance applications * 31-spline 1541H alloy axles support up to 650 hp, with the housing handling up to 800 hp * Standard 5 x 4 3/4 in. bolt pattern for a wide range of wheel options * Durable semi-gloss powdercoat finish offers long-lasting protection and a clean, sleek look * Drain plug, fill plug, and jack pad come standard to make service a breeze * Includes T-bolts and housing studs for assembling axle shafts and installing third members * High-quality roller bearings for smooth operation and long-lasting reliability
Not Yet Reviewed
$2,099.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
