Availability
FuelTech PRO550 Gen II V8 complete plug-and-play harnesses are the best link between your FT550 or FT550LITE ECU and V8 engine. Each harness is designed to install a FuelTech FT550 on mostly any racing V8 application. It comes setup for eight EV1 injectors. The harnesses come pre-terminated to suit a V8 engine with all relays and fuses for a simple 3-wire battery hook-up and ignition power. They have a 37-pin firewall connector to make installation an easy task; and with the modular construction, adding individual coils is as easy as connecting add-on harnesses utilizing the built-in output connectors. Each connector has its own label; and the connectors and harness insulation is heat, moisture and oil-resistant. Additional harness features: * The harnesses have most of the engine sensors pre-wired: TPS, hall and VR crank trigger, hall and VR cam sync, fuel pressure, oil pressure, wastegate pressure, turbo back pressure, coolant and intake air temperature, driveshaft and more. * They come pre-wired for 2x of FuelTech's EGT-4 CAN * Can be used directly with a distributor-type ignition or with additional auxiliary coil harnesses to have coil per cylinder ignition, such as smart coils or the FuelTech FTSPARK CDI unit with an additional harness. * This harness is set up for two nano wideband oxygen conditioners and two oxygen sensors. You can also use an additional adapter for a dual channel alcohol O2 with NTK O2 sensors (requires Bosch to NTK adapters). * There is an "inputs" connector to custom wire up to five additional input channels for the engine or chassis data-logging (i.e. transbrake button, suspension travel sensors, input shaft RPM, staging button and much more). * There are two additional "outputs" connectors to wire custom outputs like wastegate boost control solenoids, transbrake solenoid, dump and lockup valves, gear shift, nitrous stages and more. CONTENTS OF PACKAGING: * PRO550 GEN II V8 Complete Harness * 8-Way connector kit * 10-Way connector kit * 12-way connector kit * Operation and installation guide
Not Yet Reviewed
$1,199.00
Manufacturer Rebate
These Innovate LM-2 digital air/fuel ratio meter basic kits combine an air/fuel ratio meter and a full-function 32-channel data logger to deliver a complete tuning workshop for less than the cost of one dyno day. Whether you have a piggyback fuel controller, a race carburetor, an aftermarket ECU, ODB-II tuning software, or a flash/chip programmer, Innovate's LM-2s are the tools you need to dial-in maximum horsepower. The Innovate LM-2 digital air/fuel ratio meter basic kits' digital signal processing technology provides data on exactly how rich or lean an engine is running at any load. Their self-calibrating circuitry also compensates for changes in temperature, altitude, and sensor condition. They also feature two fully programmable linear analog outputs to connect to analog gauges, dyno computers, ECUs, piggyback controllers, and other devices with analog inputs. Analog output 1 comes factory-ready for narrow band simulation; analog output 2 is configured as 0 V = 7.35 AFR and 5 V = 22.39 AFR. Additional features include: * Patented "Direct Digital" wideband technology * Wideband O2-compatible with all fuel types * OBD-II scan tool reads/clears DTCs and logs up to 16 channels of CAN OBD-II data (cable not included) * Large, high-contrast graphics LCD * 4 fully-differential analog inputs * 2 configurable linear analog outputs * Positive lock connectors for all connections * Innovate MTS serial in and out * USB connection to your PC
( 6 )
$469.99
Manufacturer Rebate
Innovate's LM-2 digital air/fuel ratio meters combine an air/fuel ratio meter, a full-function 32-channel datalogger, and powerful software to deliver a complete tuning workshop for less than the cost of one dyno day. Whether you have a piggyback fuel controller, race carb, aftermarket ECU, ODB-II tuning software, or a flash/chip programmer, Innovate's LM-2s are the tools you need to dial-in maximum horsepower. The meters' digital signal processing technology provides data on exactly how rich or lean an engine is running at any load. The LM-2s' self-calibrating circuitry also compensates for changes in temperature, altitude, and sensor condition. The LM-2s also feature two fully programmable linear analog outputs to connect to analog gauges, dyno computers, ECUs, piggyback controllers, and other devices with analog inputs. Analog output 1 comes factory-ready for narrow band simulation; analog output 2 is configured as 0 V = 7.35 AFR and 5 V = 22.39 AFR. With the provided LM Programmer software, these analog outputs may also be configured by the user. Innovate's LM-2s are available in single wideband and dual wideband O2 configurations. Additional features include: * Patented "Direct Digital" wideband technology * Wideband O2 compatible with all fuel types * OBD-II Scan tool, read/clear DTCs and log up to 16 channels of CAN OBD-II data * Log directly to SD card (included) * Playback log data on screen with powerful LogWorks software (included) * Large high-contrast graphics LCD * Built-in rpm converter (direct frequency or with optional inductive clamp) * 4 fully-differential analog inputs * 2 configurable linear analog outputs * Positive lock connectors for all connections * Innovate MTS serial IN and OUT * USB connection to your PC
( 11 )
$559.99
—
$747.99
AEM Electronics 6-Channel CAN sensor modules provide an affordable and easy way to add temperature, pressure, fuel level, and tachometer signals on to your CD Carbon Digital dash through AEMnet CAN bus. The modules support the Bosch CAN 2.0b standard, making it compatible with many third-party devices that accept a programmable CAN bus input, which also allows you to add additional channels to a non-AEM ECU, dash, or logger. Features include: * Two temperature (thermistor) inputs * Two dedicated 0 to 5 V analog inputs * One dedicated fuel level input (0 to 250 Ohm range) * One tachometer/coil input * Fixed CAN bus speed, header length, and base address * IP67 potted enclosure/sealed connector—dust-tight and protected against water spray * Protected inputs * 12-pin DTM-style connector and pins
Not Yet Reviewed
$189.95
Racepak's Vehicle Network (V-Net) is a "smart data" transfer network able to transmit multiple signals from sensors over a single cable. The key to the V-Net system is the modular connectors that attach each of the devices to the main cable. For a function or component to be monitored on the V-Net, the signal from that device must pass through a sensor and its module (essentially a miniature computer) that identifies and retrieves only the proper incoming signals and allows other signals to pass through. The sensor measures the input from the function or device (i.e. rpm, pressure, temperature, etc.), while the module converts the signal so it can be transmitted over the V-Net. Racepak analog pre-programmed V-Net modules without sensors are analog function modules that have been programmed for general use, and have not been assigned to a specific task. Use of these modules on the V-Net cable requires the addition of a sensor and configuration of the module using DatalinkII software.
Not Yet Reviewed
$219.95
Manufacturer Rebate
Innovate LC-2 Digital Wideband Lambda O2 Controller kits are ideal for applications such as dynamometers, data acquisition systems, stand-alone ECU's, and gauges. They feature self-calibrating circuitry to compensate for changes in temperature, altitude, and sensor condition. These units include a digital input/output, and two full-programmable analog outputs. It can be "daisy-chained" for cost-effective individual cylinder monitoring, and is fully compatible with Innovates' Modular Tuning System (MTS). Additional features include: * Patented DirectDigital™ Wideband Technology * Wideband O² Compatible with all fuel types * Ability to calibrate O² sensor for maximum accuracy * Integrated dual-color status LED (Green/Red) * Two configurable linear 0-5v analog outputs * Positive lock connectors for all connections * Innovate MTS serial in/out * Serial connection to your PC * Real-time display data on screen and/or with powerful LogWorks software
( 11 )
$178.99
With Dakota Digital EFI interface modules you get more usable data—without adding more gauges! Their BIM Series of modules collect and output available readings from your system to compatible Dakota Digital VFD3, VHX, HDX, and RTX control box instrument systems. Dakota EFI interface modules are available to work with many aftermarket fuel injection kits, from AEM to MSD. In addition, for ease of installation, they are designed as direct plug-ins using the supplied harness for your specific application. The engine and transmission information that is available from the units depend on your system's module programming and add-ons. The possible values may include, but are not limited to: * Engine rpm * Engine coolant temperature * Intake/manifold air temperature * Fuel pressure * Oil pressure * Air/fuel ratio * Boost * MAP * Speedometer * Transmission temperature
( 28 )
$133.00
Manufacturer Rebate
AutoMeter CAN Bridge data modules are the ideal solution to streamline adding gauges or an InVision LCD dash to OBDII based engine and vehicle platforms (2008+). The intuitive CAN Bridge simply plugs into the diagnostic port and captures the existing sensor data and outputs up to six signals to drive a tachometer, speedometer, temperature, pressure, fuel level (0-90 ohm only), and volts on your vehicle. Quickly and easily setup your system to output the available parameters of your choice by utilizing the CAN Bridge data module's menu navigation buttons and OLED display. With this advanced CAN Bridge system from AutoMeter, you can now simplify your next instrumentation installation on your ride! Additional features: * Works with most OBD-II applications which is standardized across all OEMs starting in 2008 * Module includes OLED display and five push buttons to effortlessly navigate menus and program system for operation * Plug-and-play from OBDII to traditional round AutoMeter short sweep electric gauges, tachometers, electronic speedometers, and InVision LCD dashes * Six total channels available: tachometer, speedometer, fuel level (0-90 ohm only), temp, pressure, and volts * Simplifies instrumentation wiring and installation; no sensors to hookup, which means less wires to connect * Sensor data must be present on the data stream to function, otherwise a discrete sensor must be used
Not Yet Reviewed
$363.99
AEM 22-channel CAN sensor modules provide a way for users with carbureted vehicles to add an AEM CD digital dash display. They also let users with existing CAN-based devices add more channels to the display for viewing and/or data logging. These 22-channel modules convert analog, digital, and frequency inputs into an AEMnet CAN bus signal that can be transmitted to AEM's CD-5 carbon and CD-7 digital dashes. AEM Electronics 22-channel CAN sensor module includes: * Wiring harness with 36 in. flying leads and pre-wired CAN cable * IP65-rated enclosure is dust-tight and water-resistant * Daisy-chain two modules together for additional channels (modules sold individually) * Four dedicated 0-5 V analog inputs * Four temperature (thermistor) inputs * Four user-configurable inputs for 0-5 V, temp (including RTD) * One dedicated fuel level input (0 to 250 ohm range) * Six digital inputs, active low, protected to about 18 V, frequency, duty cycle or simple switch * One tach input, trigger when low, 12 V internal pull up * Two VR pair frequency inputs (crank, wheel, or driveshaft speeds) * Jumper selectable CAN bus speeds, 250k, 500k, 1M * Jumper selectable terminating resistor * Jumper selectable header length, 11 bit or 29 bit
Not Yet Reviewed
$413.95
Haltech's new multi-function CAN gauge displays real-time data from your Haltech ECU. Easily customize your gaugeART CAN Gauge to display the data you want to see with the included gaugeART CAN Gauge App (requires Android 4.4 or later or Apple iOS 9.1 or later). The easy-to-use app on your smartphone or tablet uses a wireless connection to the gauge for easy setup and customization. * Set up via gauge-mounted buttons or a mobile app * High-contrast, dimmable OLED display * 1, 2, or 4 gauge layouts on up to 10 different pages * Custom warning points with special warning screens SUPPORTED PARAMETERS: Boost Pressure Air/Fuel Ratio Coolant Temperature Fuel Pressure Ethanol content Air Temperature Battery Voltage Coolant Pressure EGT Fuel Level Fuel Trim Gear Position Injector Duty Nitrous Pressure Oil Pressure RPM Transmission Line Pressure Throttle Position Transmission Oil Temperature Turbo RPM Wheel Speed Wheel Slip * Above can be displayed without additional sensors. COMPATIBLE WITH: Haltech Platinum Sprint Series Haltech Platinum Sport Series Haltech Pro Plugin Series Haltech Elite Series Haltech Nexus Series
Not Yet Reviewed
$430.00
MSD Power Grid Dual NTK Wideband O2 modules are plug-and-play units that monitor and record the air/fuel ratio (AFR) of internal combustion engines. These dual channel air/fuel ratio systems are designed to seamlessly interface with MSD's Power Grid system controller (sold separately). They come with an extension harness, the sensors, connectors, and other parts necessary to accurately measure the AFR of vehicles running on gasoline and fuel containing alcohol. Features: * Plug-and-play Power Grid module * Works seamlessly with additional MSD Wideband oxygen sensor modules * No set up or calibration required (free air calibration is optional for added precision) * Can be expanded to operate with a second sensor * Fully potted and sealed unit with automotive-grade connectors * 0.5 to 4.5 V analog output voltage for a gauge or data acquisition * LEDs to monitor system operation and health * High-speed data acquisition (when used with the Power Grid controller) * Back pressure compensated AFR when used with optional exhaust pressure module (sold separately)
( 1 )
$799.95
Have you ever had a tune-up on your engine that was just perfect? Or, did you spend the time and money to dyno your engine? Wouldn't it be nice to go to the track and get back to that same tune-up every single time? With the Computech EGT Plus (exhaust gas temperature) monitor kits you can make sure that your vehicle is tuned correctly, week in and week out. Choose the EGT Plus monitor kit that suits your needs and get ready to tune your fuel system with confidence to maintain the performance edge and consistency you need to be a winner! Additional features of the EGT Plus monitor kits include: * Available with single or dual probes * Available in weld-in or clamp-on styles * Unit monitors dual temperature channels * Power source through 9 V battery or 12 V vehicle supply * Continuous mode--simple maximums * Record switch mode -- Choose when to record -- Maximum temperature and rpm * Trans-brake mode -- Launch temperature and rpm -- Finish line temperature and rpm -- Maximum temperature and rpm -- Time maximums occurred -- Notable time, temperature, and rpm
( 2 )
$479.95
—
$629.95
Biondo Racing DDI 1049 ELITE Mega switch panels bring you the same performance and reliability of the original Mega Panel with the addition of Biondo's NEW Elite Relay Board! The main differences between a standard panel and an Elite panel are: * Relays have been upgraded * The Elite Board can shift an electric or air solenoid * The Elite Board can handle 40 amps compared to standards 20 amps. The sleek and compact Switch Panel is the main part of the system and includes 6 labeled switches to control your car's most important functions. * The unique starter button and premium grade switches combine a new age design with functionality. * The ignition and fuel pump switches are dual position switches, while the fan/water pump, headlight/taillight, and aux 1/aux 2 are all three position switches. It is made to easily fit into a dragster's dash, with the overall size similar to the overall size of the conventional switch panel. * To simplify the wiring process, the Switch Panel plugs into the Elite Relay Board using the supplied heavy duty 8 ft. cable. The Elite Relay Board is the "power distribution board" and was built with durability in mind. It's capable of handling a 100 amp load with the supplied 6-gauge wire that connects from the high current connector on the Board to the master cutoff switch. It also includes dedicated relays for each switch, with each relay including its own status indicator light to let you know which circuit is on, and a dedicated fuse assigned to it. The Elite Relay Board can handle up to 40 amps on any output. In the very unlikely event that even more current is required, two outputs can be connected together for up to 80 amps. It also features an unswitched fused 12 V output that can handle up to 40 amps. This output is also shut down when the panic button is pressed. (The panic/emergency post on the board allows you to directly connect a "panic button" which will quickly shut off the power to the car in case of an emergency.) The Elite Relay Power Board has a Shift Output Controller that is only active when the ignition switch is on. The Shift Output Controller allows the driver to select whether to shift on time or RPM using a remotely mounted Select Switch (usually mounted on the dash). The Elite Relay Board also has three slide switches. An Output Control Switch to control whether the shift output will apply 12 V (N.O.) to shift or remove 12 V (N.C.) to shift and two Input Selector Switches used to tell the Elite Relay Board whether 12 V or ground is coming from the Shift Controllers. The relay board also includes the "Dual Select" feature which allows you to individually customize how to control each of the three position switches. For example; the switch on the Mega Panel labeled FAN / Water Pump turns on the fan and water pump in one position and the water pump in the other position. By turning on the Dual Select dip switch located on the relay board, you can change it so that the fan only is on in the fan position and the water pump only is on in the other position. The wiring kit includes enough color-coded wire, connectors, wire ties and a complete color-coded diagram to help you neatly wire a vehicle. Features / Specifications: * Mega Panel size: 8 in. x 3 1/4 in. x 1 3/4 in. * Panel mounting holes 7 1/2 in. left to right, 2 3/4 in. top to bottom * Relay Board size: 8 1/2 in. x 5 in. x 1 in. * Complete color-coded wiring kit with connectors and color-coded diagram professionally wire your race car for years of trouble free racing.
Not Yet Reviewed
$667.99
Haltech Input/Output 12 expanders are CAN devices that increase the number of available analog and digital inputs, as well as digital outputs. They are ideal for additional pressure, temperature, and flex fuel sensors that can be used for engine protection or general monitoring of your engine's vital data. I/O expanders integrate with all Haltech Platinum, Elite, and Nexus Series ECUs and VCUs. Increase the functionality of your ECU with Haltech I/O expanders. Select the Haltech I/O 12 expander (Box A or B) suitable for your ECU. They are available in different options: Expander with 12 in. (300mm) CAN cable DTM 4- to 8-pin Tyco, expander with cable and matching 24-pin TYCO plug and pins or expander with cable and matching 8 ft. (2.5m) flying lead harness. Features: * Four Digital Pulsed Outputs (DPO) * Four Digital Pulsed Inputs (DPI) * Four Analog Voltage Inputs (AVI) * Two expanders can be combined for up to 24 additional channels (subject to ECU compatibility). Functions available depend on ECU used.
Not Yet Reviewed
$370.00
—
$495.00
Manufacturer Rebate
If you demand maximum horsepower, Dedenbear disc-style throttle stops are for you. Mounted underneath a Dominator carburetor, they look and act like a 4-hole carb spacer. No restriction of flow at wide-open means no power loss! They also offer exceptional repeatability when closed, because the air/fuel openings are in the center of the carb bore. Additional features include: * Designed specifically for the highest mph cars * No flow restrictions for maximum horsepower * Needle bearings for smooth, precise activation * Centered openings for best repeatability * Simple and accurate adjustability * Corrosion-resistant stainless steel and brass * Adjustable opening and closing rates * Low-profile--only 1.5 in. tall
Not Yet Reviewed
$1,269.99
—
$1,326.99
Wagner Tuning offers MFD32 data acquisition displays for a wide range of vehicles, including cars and trucks from Audi, Volkswagen, Ford, and Toyota. Now you can always have all relevant values in view. With these advanced cutting-edge displays, you gain access to all the data from your engine control unit. Each Wagner display queries the sensors directly via the Can Bus protocol and presents the information on the reliable MFD28 display. Wagner has fine-tuned the manufacturer-specific Can Bus protocols to achieve maximum query speed. MFD32 displays seamlessly integrate into your vehicle's interior. Key features: * Perfect integration into your vehicle's interior * Query up to 128 sensors * 10 individually customizable views with our DSS - Display Setup Software * Pre-configured views for a quick start with our display * Easy Plug-and-Play installation with our cable set – simply plug it in and you're ready to go * 4 additional analog inputs for monitoring exhaust temperature, oil pressure, and more * Direct ethanol sensor integration * Best readability with an optional anti-glare film * Sensor querying on par with manufacturer diagnostic tools Additional Features: * Performance meter: Measure your acceleration times with the Performance Widget: 0-100, 100-200, 0-200 * Data logging: Log all data on the internal SD card—whether it's "on-demand" (start with a fingertip) or permanent. All data from your last drive is stored * Preset alarms: Activate and customize pre-set warning messages, such as receiving a significant warning when the exhaust temperature exceeds 900 degrees F * 4 Analog additional inputs: Connect additional temperature and/or pressure sensors for further monitoring possibilities, including exhaust temperature or exhaust backpressure. An ethanol sensor can be connected to one of the digital inputs * Error reading/deletion: Read engine control unit errors in plain text and delete them * Customization: Customize the startup screen or choose from various widgets to tailor the display to your preferences * Seamless vehicle integration: Left-hand and right-hand drive displays are available --- Access to all engine control unit (ECU) data: Wagner Tuning provides your display with a pre-configured TRI file as standard. This file defines all the sensors that can be queried, including: * Temperatures: Engine coolant temperature, intake air temperature, exhaust temperature, transmission temperature * Pressures: Boost pressure, ambient pressure, oil pressure * Lambda/Mixture: Lambda target/actual, short-term lambda adaptation, long-term lambda adaptation, MAF, engine load, torque * Driver dynamics: Brake pressure, vehicle speed, throttle angle/gas pedal position * Other: RPM, total ignition angle, gear, battery voltage, ignition angle correction per cylinder * Analog inputs: Additional sensors like oil temperature, fuel pressure, oil pressure, exhaust temperature, and more can be added, including an ethanol sensor for Flex Fuel vehicles * Please note that not every engine provides all these values
Not Yet Reviewed
$499.00
Wagner Tuning offers MFD15 data acquisition displays for a wide range of vehicles, including models from Audi and Ford. Now you can always have all relevant values in view. The MFD15 Gen2 is equipped with an OLED screen, which offers best readability even in direct sunlight. Due to the outer diameter of 52mm, the display is compatible with commercially available bezels for the interior, even without a vehicle-specific holder from Wagner. The operation is done with the two, on the windshield mounted, push-buttons or variable the optional rotary knob. --- Key features: * Compact design: 52mm in diameter and only 12.5mm deep * Switching flash: The LED on the front of the display can be used as a switching flash and/or as a warning LED and can be configured freely * Can Bus: Support of Can Bus ECUs, OBD2 from 2008 and deep values for VW/Audi from 2008 or build your own Can Stream * WLAN: connect to your smartphone or PC and perform all further steps via our Web UI * Additional inputs: connect up to 6 analog sensors to the inputs or connect an ethanol sensor* directly to the display * Preset alarms: predefined alarms can be easily activated and customized. For example, get a big alert when the exhaust gas temperature is above 900 degrees F. * Customization: Use your own startup logo or background image to make it your MFD15 Gen2 * Online logging: Log your data with your smartphone or PC and save the log to your device for later analysis * Flex fuel: View ethanol content and temperature on your display * Can switching: Switch can switches using the buttons on your display and forward the readings from your analog inputs to the can bus --- Different views: Choose up to eight pages of different views and customize your display to best suit you and your vehicle: * Analog pointer * Double value * Gear indicator * 4-fold values * 6-fold values * Bar + double display * Round display * Bar graph (double across) * Performance meter * Bar chart (1-6-fold upright) * Single value
Not Yet Reviewed
$329.00
Wagner Tuning offers MFD28 data acquisition displays for a wide range of vehicles, including cars and trucks from Audi, Volkswagen, Ford, BMW, Dodge, and Ram. Now you can always have all relevant values in view. With these advanced cutting-edge displays, you gain access to all the data from your engine control unit. Each Wagner display queries the sensors directly via the Can Bus protocol and presents the information on the reliable MFD28. Wagner has fine-tuned the manufacturer-specific Can Bus protocols to achieve maximum query speed. These displays seamlessly integrate into your vehicle's interior. Key features: * Perfect integration into your vehicle's interior * Query up to 128 sensors * 10 individually customizable views with Wagner Tuning's DSS (Display Setup Software) * Pre-configured views for a quick start with our display * Easy plug-and-play installation with Wagner's cable set; simply plug it in and you're ready to go * 4 additional analog inputs for monitoring exhaust temperature, oil pressure, and more * Direct ethanol sensor integration * Best readability with an optional anti-glare film * Sensor querying on par with manufacturer diagnostic tools Additional Features: * Performance meter: Measure your acceleration times with the Performance Widget: 0-100, 100-200, 0-200 * Data logging: Log all data on the internal SD card—whether it's "on-demand" (start with a fingertip) or permanent. All data from your last drive is stored * Preset alarms: Activate and customize pre-set warning messages, such as receiving a significant warning when the exhaust temperature exceeds 900 degrees F. * 4 Analog additional inputs: Connect additional temperature and/or pressure sensors for further monitoring possibilities, including exhaust temperature or exhaust backpressure. An ethanol sensor can be connected to one of the digital inputs * Error reading/deletion: Read engine control unit errors in plain text and delete them * Customization: Customize the startup screen or choose from various widgets to tailor the display to your preferences * Seamless vehicle integration: Versions for left- or right-hand drive are available --- Access to all engine control unit (ECU) data: Wagner provides your display with a pre-configured TRI file as standard. This file defines all the sensors that can be queried, including: * Temperatures: Engine coolant temperature, intake air temperature, exhaust temperature, transmission temperature * Pressures: Boost pressure, ambient pressure, oil pressure * Lambda/Mixture: Lambda target/actual, short-term lambda adaptation, long-term lambda adaptation, MAF, engine load, torque * Driver dynamics: Brake pressure, vehicle speed, throttle angle/gas pedal position * Other: RPM, total ignition angle, gear, battery voltage, ignition angle correction per cylinder * Analog inputs: Additional sensors like oil temperature, fuel pressure, oil pressure, exhaust temperature, and more can be added, including an ethanol sensor for Flex Fuel vehicles * Please note that not every engine provides all these values
Not Yet Reviewed
$499.00
Manufacturer Rebate
Innovate's TC-4 Plus is ideal for applications such as dynamometers, data acquisition systems, or standalone ECUs. They offer crucial benefits for engine tuning and protection by providing high-quality, precise, and fast temperature readings. For turbocharged engines, race cars, and high-performance builds, EGT monitoring is an essential diagnostic tool that goes beyond what a standard air-fuel ratio (AFR) gauge can provide. Additional product details: * The probes are built with durable materials to withstand the extreme temperatures and vibrations found in performance and racing applications * Available individually for replacement or as an added accessory, the probes include a weld-in stainless steel fitting and bung with 6 ft. wire * Innovate's K-type thermocouples are compatible with their range of tuning devices and data loggers, including the TC-4 Plus, LMA-3, and DL-32
Not Yet Reviewed
$109.99
AEM Electronics CD-7 digital racing dash displays feature 7 in. full-color digital screens that are super bright, high contrast, and with sunlight-readable displays. To ensure visibility at all times, they also have integrated glare diffusers and shade hoods to overcome the brightest daylight conditions. The CD-7s are designed to accept channels from CAN bus connections—and two CAN bus channels are included so that they can receive and collect data from AEMnet-enabled devices. Seven ultra-bright LEDs span the top of the display housing for rpm and shift light indication. You can program them to ascend in specific increments based on rpm range, and flash when it's time to shift. Brightness is also programmable on the fixed color LEDs. Two large buttons are included on the face of the display, allowing easy page changing and memory resetting—even with driving gloves on. These button functions are duplicated on the rear connector, allowing you to mount remote buttons on the steering wheel, if desired. Two additional programmable LEDs are located above the toggle buttons on the sides of the housing. AEM offers the CD-7 as "display only" (non-logging) or with built-in logger (CD-7L). The units are available in either a cast aluminum or carbon fiber composite housing—with sealed connectors on the rear and anti-vibration mounts.
( 2 )
$1,649.95
—
$2,099.95
Attention sportsman drag racers: Racepak IQ3D digital dash instruments offer a compact, all-in-one solution for data acquisition. Adding a robust, built-in data logger to the popular IQ3, the drag race versions display information on four user-definable pages—and recorded data is stored on a microSD memory card located on the face of the dash for easy access. You can record engine rpm, driveshaft rpm, oil pressure, water temperature, and battery voltage. Smarter racing; get onboard performance that could change the way you compete ... and win, with Racepak IQ3D. Racepak IQ3D drag racing digital dashes specifications include: * Programmable LED shift lights * User-defined 5-character sensor input names * Four programmable external warnings * Shielded, low-luster display for open cockpit use * Can add up to six additional V-Net channels
( 1 )
$1,799.95
On Sale
AEM CD-5 Carbon digital racing dash displays are the lightest, brightest, ultimate track day digital dashboard displays that play well with others! The CD-5 units accept channels from two separate user programmable CAN bus connections—works with AEMnet enabled devices and non-AEM third party devices side-by-side. More key features and benefits: * Full-color, 5 in. screen * Direct sunlight readable (1000cd/m2 brightness and anti-glare filter) * Seven LED rpm/shift light indicators on top of the housing are programmable and dimmable * Layout files interchangeable with all versions of the CD-7 * Wiring interface/harness is identical to the CD-7 * Rugged, lightweight flow-molded carbon fiber composite enclosure * Two additional programmable LEDs are located above toggle buttons on the top of the housing on either side of the integrated LED shift lights * IP66 water resistance allows for operation in boats and motorcycles without worry * Seven programmable pages, including four main pages, alarm, on-change and start-up pages * Dedicated alarm page quickly identifies problems, and is programmable in almost any language (user defined) * Unique On-Change page can be used to identify map switching for boost, traction, lap times, etc. * Convert CAN bus channel values to user-defined text in multiple languages * Available with or without 200Mb internal logging (up to 1,000Hz/channel) * Available with or without on-board GPS receiver and antenna * Use included page layouts and input your channels and text, or create your own from scratch
Not Yet Reviewed
$1,599.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
