Availability
MSD 6-BTM CD ignitions are ideal for engines with a turbo or supercharger. Not only will they benefit from full power CD sparks, but there is also an adjustable boost/timing retard circuit to prevent detonation. The dash-mounted control knob lets you easily adjust the amount of timing retard from 0-3 degrees per pound of boost pressure. Dial away engine-damaging detonation by retarding the timing in relation to boost pressure, and run on the threshold of detonation for maximum power and efficiency. You also get overrev protection from the soft touch rev control. They work with 4, 6 (even fire only), and 8-cylinder engines using a distributor. They include rubber shock mounts and 3,000, 6,000, 7,000, and 8,000 rpm plug-in rev limit modules.
( 24 )
$749.95
On Sale
When it comes to late model performance parts, nothing beats bolt-on and direct connection components—especially when they improve performance like these new replacement MSD Blaster ignition coils. They're designed with improved materials and windings to produce a stronger spark. This improved spark helps burn the fuel mixture more efficiently, resulting in smooth idle and heightened mid-range rpm power. Choose the OEM replacement designed for your year/make/model application.
( 622 )
$155.95
$101.95
—
$172.95
If you run a blower, turbo, or even a naturally aspirated engine, MSD's Boost Timing Masters allow you to run at the edge of detonation for maximum power output. They can prevent detonation by automatically retarding the timing as your manifold pressure increases. The secret lies in a boost pressure sensor that's inside MSD's solid-state control box. The sensor reads boost pressure through a 1/8 in. vacuum hose attached to a boost pressure source. The result gives you peak power without harmful detonation. A dash-mounted control knob allows you to dial in the retard from 1 to 3 degrees per pound of boost pressure, up to a maximum retard of 15 degrees. Vacuum tubing is not included. These units must be used with an MSD 6, 7 or 8 series ignition.
( 6 )
$926.95
Your Ford is built to eat asphalt and clear its pipes with compacts. Summit Racing™ Ford Mod Motor coil-on-plug ignition coils are engineered to fuel the powerful combustion needed to unleash its inner potential. We use pure copper wire, rare earth magnets, and a custom primary and secondary wind, to provide 40 percent more voltage and 20 percent more energy (mj) from a stock-sized coil housing. They fit in the stock location, making changing these coils as easy as possible. If you're running at increased PSI with a supercharger, turbocharger, nitrous, or are burning E85, you need the hottest and strongest spark possible to burn your fuel. With the increased voltage and energy output values, your cylinders will get the spark they need to maximize fuel burn! These ignition coils are available in a variety of power options; order the model recommended for your vehicle.
( 59 )
$18.99
—
$320.92
ICT Billet remote mount coil brackets mount eight coils and are designed to work with a wide variety of LS engine swaps. They are available to fit most OE and some Holley EFI coils. Made from aerospace grade billet aluminum, most feature a natural finish. The kits include two sets of brackets, bolts, and spacers where applicable. They work great for turbo setups or whenever a clean-looking engine bay is important. Most ICT Billet remote mount coil brackets are designed to be used with LT1 Camaro ignition wires.
( 20 )
$61.99
—
$87.99
Mopar and Hemi mean a lot to car guys--they embody power and classic design. Summit Racing™ Mopar Hemi coil-on-plug ignition coils are a great way to match well-engineered engines with the pure power of plasma. We use pure copper wire, rare earth magnets, and a custom primary and secondary wind to provide 20 percent more voltage and 30 percent more spark energy (mj) over stock. All this comes from a stock-sized coil housing. They fit in the stock location, making changing these coils as easy as possible. If you are running a supercharger, turbocharger, nitrous, or are burning E85, you need the hottest and strongest spark possible to burn your fuel. With the increased voltage and energy output values, your cylinders will get the spark they need to maximize fuel burn!
( 14 )
$59.99
—
$479.92
Designed for engines with up to 14.5:1 compression ratios, nitrous, superchargers, or turbos, FAST's HI-6R ignitions keep your ride performing all the way down the track. These fully digital, multi-spark, CD ignitions deliver higher spark-gap current than comparable digital CD ignitions. Designed for street and racing use, they come with FAST's "Plug-n-Go" universal harness to cover most installations, with optional harnesses available separately. Their built-in rev limiter automatically drops cylinders in firing order to prevent fuel loading, and is adjustable by increments of 100 from 600-9,900 rpm, without the need for chips. Other built-in features include a tach accuracy check, a system problems check for easy problem diagnosis, and crossfire protection for supercharged and turbo applications. The optional 0-20 degree adjustable timing retard and MAP sensor make a great combination for nitrous and turbo applications. They feature fully potted construction with soft urethane for heat, dirt, and moisture protection, and an anodized heat-sink shell for reliability. FAST designed them to be points, mag, or module-triggered for 4, 6, and 8-cylinder engines with distributors.
( 3 )
$320.95
ICT Billet ignition coil bracket spacer kits include 16 spacers and 16 bolts. They will be needed when you're installing certain LS ignition coil brackets. These natural finish billet aluminum bolts and spacers will work great for turbo setups.
( 4 )
$19.99
Granatelli Motor Sports ignition system combo kits feature Granatelli's patented 0 ohm wires with extremely low resistance that maintain very high noise suppression. They transmit the full electrical energy of the ignition source to the spark plugs. The end result is increased horsepower, torque, and fuel economy. Order the kit recommended for your vehicle and engine application. Product details: * Direct replacements exceed OEM specifications; OBD-II computer safe * Increase power to the spark plugs up to 400 percent over stock * 0 ohm resistance, no RFI/EMI interference thanks to patented protector ring * Works with all street and race fuel injection systems * Solid stainless steel connector cables and snap-lock spark plug connectors * High-temperature silicone boots; 8mm jackets with fiberglass-reinforced braid resist temperatures up to 500 degrees F * Ideal for use with aftermarket headers or turbocharger systems * Includes all necessary hardware
Not Yet Reviewed
$308.98
—
$878.75
DIS-4 Plus HO digital ignitions are higher-output versions of the DIS ignition controls from MSD. They're designed for full race engines running high boost pressures from turbos, blowers, or nitrous. Their increased output will light up fuel mixtures even under these extreme cylinder pressures. Your late model distributorless ignition system will never be the same! The capacitive discharge ignitions feature multi-channel capability, complemented with multiple sparks, two rev limiters, and a timing control. These DIS ignitions are engineered with the latest in digital science, including power MOSFET technology and efficient IGBT coil drivers. They're managed by a 15 MHz micro-controller for extremely fast compensations and decisions. In the end, this creates incredibly accurate spark delivery, rev limiting, and timing functions. Throttle response and mid-range pull are also improved, due to a series of powerful multiple sparks that last for 20 degrees of crankshaft rotation. There is a two-step rev limiter, which gives you one limit to set for holeshots and another for top-end performance. For engines using nitrous or extremely high cylinder pressures, you can also program a high-speed retard after the engine hits total timing. Both of these features are easy to adjust with the new built-in rotary dials. They also feature an ignition interrupt that will prevent the engine from starting by disabling the output to the coil, a retard feature that retards the timing at the top end to prevent detonation, and an LED monitor that will alert you of a low supply of voltage or faulty input signals. Also, there is now a true step retard that can be activated through your nitrous solenoid wiring! The DIS-4 HO Plus digital ignitions are designed for 6 or 8-cylinder engines with three or four coil packs.
( 1 )
$1,199.95
MSD MC-4 programmable ignition controls for motorcycles combine multiple spark discharge and digital computer accuracy into one compact ignition system, giving you the best of both worlds. You'll be able to program the MC-4s at the track, on the dyno, or wherever, with or without a computer! The supplied Pro-Data plus software gives you just what you have been waiting for--the ability to program ignition timing curves to suit your engine's needs. These MC-4 ignition boxes are for use with single or dual spark plugs per cylinder, and are 1, 2, or 4-cylinder selectable. Features include: * Computer interface for easy programming * 0-25 degree start retard * Mapable run timing curve * Launch ramp delay by time 0-2.5 seconds * 3-step retards by rpm or switch * 0-2.50 second step retard off delay for precise nitrous control * Progressive timing retard by time for progressive NOS * Launch timing curve to prevent tire slippage * Individual cylinder timing when optional cam sync sensor is used * Gear retard--retard a different amount for each gear * Shift kill feature with programmable delays 20-99 milliseconds * Shift kill modes for manual, auto 1, 2, and auto 1, 2, 3 * Optional boost retard curve when used with an external MAP sensor for turbo applications (2-45 psi) * Built-in rpm-activated window switch--turn "on" any device up to 3 amps at any rpm, then back off at a different rpm * Sequential shift light--turn on an optional shift light at a different rpm for each gear * Sequential shifter turns any air shifter into a fully automatic shifter (3 amps max) * Tach output wire for tachometers or data recorders * Monitor mode for easy setup or 3-step switches
Not Yet Reviewed
$1,599.95
Dyna 2Ki Programmable Ignitions not only add to, but extend, many features of the Dyna 2000 modules with a completely new design that fits under the cam cover. Every time power to the ignition is switched on, the 2Ki checks to see if the coil is shorted, mis-wired, or of the wrong type. If an error is detected, the 2Ki will immediately switch off and issue a warning. After starting, the 2Ki continuously monitors the status of the coil and wiring. All 2Ki ignitions are PC programmable: * 8-point fully-definable wide-open throttle curve * 8-point fully-definable part-throttle curve * Rev limit programmable in 50 rpm steps * Programmable dead cranking revs 0-10 * Programmable rear cylinder offset, total of +/- 10 degrees Data recording functions: * Total engine hours * Time at wide-open throttle * Number of engine starts * Longest time operating at wide-open throttle * Maximum rpm * Seconds near rev limit * Statistical analysis of time at rpm Additional features and benefits include: * Single-fire operation down to zero rpm for easier cranking and kicking * Operates in all combinations of single-fire or dual-fire with single plug or dual plug heads (when used with appropriate coils) * Eight advance curves to cover a broad range of engine builds and riding styles * Over-rev protection adjustable from 6000 to 7500 rpm * Adjustable timing retard for nitrous and turbo applications * VOES indicator; shows the status of the VOES switch, also indicates when retard mode is active * Built-in tach driver delivers stable tach signal even during rev limiting; can be used to activate shift lights, auto shifters, and other accessories * Easy static timing with built-in timing indicator (no timing light required) * Intelligent over-current and short circuit protection * Active dwell control continually adjusts coil current to maintain maximum spark energy up to redline while eliminating coil stress caused by overcharging at idle * High-efficiency design reduces battery draw for easier cold weather starting and lower charging system load * Ruggedized output--cannot be damaged by broken or disconnected spark plug wires * Over-voltage protected against momentary spikes (positive and negative) as well as surges caused by faulty voltage regulators or quick-charge battery boosters * Harness constructed with TXL cross-linked polyethylene automotive wire for exceptional resistance to abrasion, heat, and chemical attack * High-temp glass-braid jacket further increases the toughness of the harness and provides a tight, clean appearance * Wire colors closely match the factory harness for error-free installation * Manufactured with premium-quality components designed for operation in a high-temperature, high-vibration environment * One-piece aluminum housing and thermally-conductive epoxy encapsulation provide superior heat dissipation and outstanding shock, vibration, and moisture resistance * Advanced microprocessor technology * Quartz crystal accuracy.
Not Yet Reviewed
$461.99
On Sale
Holley ignition coil spacers are great for turbo builds or other applications where more ignition coil clearance is needed. They are available for Gen I and Gen V coils. Choose the spacers designed for your coils.
Not Yet Reviewed
$15.47
$8.51
These timing retard controls from Fast are an ideal way to add zero to 20 degrees of timing retard in three modes--continuous, demand, and boost proportional--to HI-6, HI-6R, and HI-6DSR ignition systems. The sealed units can be mounted under the dash, and an LED light comes on when retard is commanded. Use them with the optional boost (MAP) sensor for boost proportional retard. They're compatible with nitrous, turbo, and supercharged on-demand retard hookup, and are not intended for underhood mounting.
Not Yet Reviewed
$227.95
FAST's HI-6S ignitions will give you up to 70 percent more spark-gap energy than stock ignitions. Designed for street and racing use, they come with FAST's "Plug-n-Go" universal harness to cover most installations, with optional harnesses available separately. With a max output of 8,000 rpm (can be extended to 10,000 rpm on 4-cylinder engines) for up to 9.5:1 compression engines, you'll be sure to feel the improvement. Their built-in rev limiter automatically drops cylinders in firing order to prevent fuel loading, and is adjustable from 3,100-9,900 rpm in 100-rpm increments, without any chips. The optional 0-20 degree adjustable timing retard and MAP sensor make a great combination for nitrous and turbo applications. They have a soft urethane encapsulation that seals against moisture, dirt, dust, vibration, and heat, and an anodized heat-sink shell for reliability. FAST designed them to be points or module-triggered for 4, 6, and 8-cylinder engines with distributors.
( 1 )
$209.95
aFe Scorcher HD modules include a high-quality case and wire harness with factory-style connectors for an easy plug-and-play installation. An LED light switch provides in-cabin, on-the-fly power adjustments. The four power settings are adjustable with one button and the LED light represent the settings: stock (green), sport (yellow), sport+ (orange) and race (red). The aFe Scorcher HD modules add significant power by altering pressure sensor signals to increase turbo boost and fuel pressure to improve vehicle efficiency, power, and throttle response. They use a high-quality aluminum extrusion black powdercoated enclosure casing and factory-style connectors which requires no modification to your factory harness. These factory-style connectors plug directly into the stock wiring harness connectors and sensors.
( 2 )
$461.00
Designed for an engine named after the wild dog of the prairies, Summit Racing™ Ford Coyote coil-on-plug ignition coils will unleash the power in your wild ride. They are engineered to convert the power of pure plasma into the horsepower your engine has been begging to let out. Let loose the beast, and hear those tires bark, with the power of complete ignition. We use pure copper wire and custom primary and custom secondary windings to provide 30 percent more spark energy (mj).You get all of this from a stock-sized coil housing that fits in the stock location. If you are running a supercharger, turbocharger, nitrous, or are burning E85, you need the hottest and strongest spark possible, to burn your fuel. With the increased spark energy output, your cylinders will get the spark they need to maximize fuel burn.
( 1 )
$46.99
—
$375.92
MSD Blaster Power Sports ignition coils deliver the most energy for easier starting, quicker throttle response, and powerful spark energy throughout the rpm band of your powerplant. Power Sports coils are direct bolt-on, plug-in replacements for factory units on many popular powersports machines. If you demand maximum performance for maximum fun, these easy, economical MSD upgrades are the perfect fit for your ATV, UTV, motorcycle, snowmobile, or jet ski. Benefits include: * Available in red and black * Optimized coil engineering * Easier starts * Smoother idle * Crisper throttle response * Improved power from idle to redline * Supplied with mounting bracket and hardware
( 4 )
$155.95
On Sale
Don't take chances with old or questionable ignition coils that can leave you stranded. Standard Motor replacement ignition coils are designed to exceed OEM specifications for accurate, maintenance-free operation. They're offered in a variety of styles, such as coil pack, canister, and E-core; and these direct-fit coils are available to replace a wide range of factory part numbers/applications.
( 81 )
$34.99
—
$69.99
$31.49
—
$62.99
Bosch ignition coils are designed to provide your ignition system adequate spark to start it and keep it operating smoothly. They are manufactured from quality materials and are available in different styles to fit your specific vehicle application. All Bosch ignition coils are direct fit, so no modifications should be required.
( 3 )
$77.99
On Sale
FTI Performance Automatic Transmission reluctor rings simplify the installation of an electronic speedometer. Their installation provides you many more choices when selecting a speedometer for your street or race car.
Not Yet Reviewed
$39.99
$35.99
MSD low-resistance HEI bushings prevent excessive heat buildup. The carbon rotor button in a stock HEI distributor cap has very high resistance. When the high voltage of an MSD 6, 7, or 8 Series ignition is added, this resistance builds up heat and can actually melt the distributor cap. To solve this problem, install one of these MSD low-resistance HEI bushings, which will pass the secondary voltage from the distributor cap to the rotor without the excessive heat buildup.
( 15 )
$23.66
Is it time for a tuneup? Replace your distributor's worn-out rotor with a new one from Standard Motor Products. Don't take chances with old, questionable, or faulty ignition components that can leave you stranded. Standard Motor Products replacement distributor rotors are designed to exceed OEM specifications for dependable, accurate, maintenance-free operation. Trust your vehicle's ignition system needs to Standard Motor Performance.
( 46 )
$2.99
—
$11.99
Moroso ignition control modules provide high-output consistent dwell, accurate timing, extended durability, and high spark output. Whether you're looking for OEM replacement or high performance gear, Moroso has you covered.
Not Yet Reviewed
$86.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
