Availability
Failure or poor performance from a coil can result in a misfire, a rough-running, hard-starting engine, and excessive emissions. ACDelco ignition coils provide the performance needed to help keep vehicles running the way that they were designed. These coils have corrosion-protected laminations to guard them from the harsh operating environment. Primary and secondary coil windings often feature molded plastic protection. Order the replacement model designed for your vehicle and engine application.
( 27 )
$50.99
For over 40 years, Cardone's innovative remanufacturing processes have provided a high-quality, lower-cost alternative to new replacement parts. It doesn't matter if your vehicle is vintage or fresh off of the dealer's lot--Cardone is your source for the highest quality remanufactured parts. Through "reverse-engineering" failed parts, their engineers see where, and why, they failed. They reengineer their remanufactured products, where applicable, to reinforce failure-prone areas for longer-lasting performance. Cardone remanufactured parts cost up to 50 percent less than new--especially true with late-model, high-tech products. Cardone restores used auto parts back to their original fit and function, using only about 20 percent of the energy and raw material needed to build a new part; so you not only save money, but you also help save our planet. Features of Cardone remanufactured distributors include: * All electronic module components are 100 percent computer-tested to ensure full functionality * Automated test equipment verifies signal strength, correct polarity of wire harness, air gap, and crank reluctor tooth size, as well as ignition coil and pickup performance * Cardone uses the right gear hardness for the appropriate application: if the gear is too hard, it will damage the cam; if it's too soft, the gear itself will be damaged, potentially causing severe engine damage (many offshore manufacturers use only one gear hardness) * OE components with consistently high failure rates are 100 percent replaced or repaired to meet or exceed OE performance * Precise machining tolerances prevent oil leakage, poor timing, the setting of the "Check Engine" light, and premature failure
( 100 )
$82.99
—
$169.99
On Sale
ACCEL Super Coils are engineered for a faster rise time and a longer spark duration. They produce higher spark energy for increased performance. These coils are available for a wide variety of specific engine applications. Order the set designed for your make and model.
( 802 )
$114.95
FiTech Go-Spark Ready-To-Run distributors have a built-in module for easy installation with a simple 3-wire hook up, negating the need to run an external ignition control box. They are perfect distributors for a crate engine or when replacing an old points-triggered distributor. Each one features a CNC-machined 6061 T-6 aluminum housing with a centerless ground shaft. The shaft rides on an upper sealed roller bearing with an extended length lower bronze Oil-Lite bushing for smooth operation at high rpms and extended service life. A high-output magnetic pickup and large paddle wheel reluctor provides a strong trigger signal at high rpms, while the built-in high performance inductive storage module supplies unrivaled energy to the coil ensuring maximum performance at all rpm levels. The fully adjustable mechanical advance is welded to the top of the shaft for easy access and is plated to reduce friction and prevent corrosion for long term durability. An adjustable vacuum advance canister allows you to dial in the ideal timing curve to meet your high performance or cruising needs. FiTech Go-Spark Ready-To-Run distributors have caps and rotors molded in high-quality 30+ percent glass fiber reinforced polyester (PBT) that offers both high-impact and dielectric strength while resisting carbon tracking. The cap contacts are brass and the rotor spring is stainless steel for long-term maximum conductivity. With FiTech's 3-year limited warranty, you can be confident in the quality performance of your Hot Rod. Select the ideal distributor for your vehicle.
Not Yet Reviewed
$329.00
—
$375.00
Scott Drake distributor caps are available in both OEM and aftermarket styles. The caps offer a true factory appearance. Most distributor caps are exact replicas of the originals, and a model with the raised "Autolite" logo is a must for any show car. These parts are essential to keep your engine running smoothly, so choose Scott Drake quality replacements.
( 26 )
$20.17
—
$74.22
Since you're installing that new distributor, you'll need to hold it down with something. Why not use one of Mr. Gasket's hold-down distributor clamps? Made from heavy gauge steel, these clamps are the perfect way to dress up the engine compartment.
( 27 )
$15.23
FAST XDi Sportsman distributors are designed to deliver the most accurate trigger signal possible throughout the entire rpm range of your race engine. This is accomplished through the use of an advanced Hall-effect style pickup, which is then converted to a signal that most CD ignition controls accept. The benefit of a Hall-effect pickup is: there is no retard, commonly called magnetic pickup compensation—so you can ensure your timing remains stable from idle to race rpm. Inside the CNC-machined billet housing is a polished stainless steel shaft that is supported with sealed ball bearing on the top and a long bushing on the bottom. They've also reduced end play in the distributor to take out any timing variations and damage to the gear. FAST XDi distributors are supplied with high-quality rotors and caps, and are available with a large diameter Ford-style cap or smaller diameter GM points size cap with HEI terminals, as well as either a steel or bronze gear. Order the Sportsman tailored for your year/make and engine application.
( 1 )
$407.95
—
$439.95
Edelbrock Max-Fire distributors are ready to run right out of the box—and are the perfect upgrade for your ignition system. They're ideal for replacing or upgrading from a points triggered distributor. Max-Fire kits feature precision machining for a perfect fit, along with a simple 3-wire hook-up for an easy installation (with no need to run an external ignition control box). The centerless ground shaft utilizes an upper sealed roller bearing with an extra-long lower bronze Oil-Lite bushing for smooth operation. The high-output magnetic pickup and large paddle wheel reluctor deliver a strong trigger signal at high RPM for maximum performance. All of these features allow Max-Fire distributors to provide unrivaled voltage to the coil, ensuring that you're getting maximum performance from your engine. (Edelbrock also recommends a new Max-Fire coil for maximum voltage output, ensuring you get the most from your high performance engine at higher RPM's.) Each distributor includes a cap, rotor, retainer and mechanical advance curve kit. Order the model recommended for your year/make and engine application.
( 15 )
$487.95
From raw materials to the final product assembly, each Spectra Premium ignition coil goes through rigorous test requirements to ensure they meet or exceed OE specifications for fit, form, function, and proper installation. Order the model designed for your vehicle and engine application. Features and benefits of all Spectra Premium ignition coils: * Each unit is durability tested at 100 cycles of thermal shock (-50 to 300 degrees F) to ensure reliability against extreme vibration * Each coil is road tested to ensure real world performance and to verify that each design meets Spectra's quality standards * 100 percent copper in both primary and secondary windings * Windings insulated by high-voltage enamel coating
( 1 )
$15.99
—
$18.99
MotoRad ignition coils are engineered to maximize spark voltage duration for optimal engine performance. They're designed to perform under severe operating conditions and protect against extreme heat. All coils meet or exceed OEM specifications. Order the replacement ignition coils recommended for your vehicle. Additional product details: * Heat-resistant magnet produces max voltage output at all engine speeds * Graphite-infused platinum connections resist corrosion and offer superior conductivity and durability * Primary and secondary windings made with ETP-grade copper provide superior temperature protection and voltage conductivity * Pre-applied dielectric grease for easy installation
Not Yet Reviewed
$19.99
—
$24.79
Dorman distributor gears are engineered for affordability and convenience. These drive gears are direct replacements, which means an exact fit—offering an additional layer of ease and value to restore your engine timing and ignition. Dorman distributor gears are made of high-quality materials for long life. Order the model designed for your vehicle and engine application.
( 2 )
$31.99
On Sale
MSD Pro-Billet Ready-to-Run distributors are the perfect upgrade for weak OE electronic distributors, outdated points distributors, and large HEIs or DuraSparks. All that's required is to install the distributor in the engine, and connect three wires and the coil! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. It will smooth out the engine's idle, improve starting, and perform at a much higher rpm. The housing is machined from billet 6061-T6 aluminum, using state-of-the-art CNC mills and lathes for a unit with no porosity or weak areas. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing, while an extra-long sintered bushing guides the shaft at the base of the housing. This shaft also receives a QPQ coating for low friction wear and resistance against corrosion from humidity and ozone buildup. The distributors feature MSD's adjustable mechanical advance, which allows you to custom-tailor an ignition curve to match your engine's needs. Most models are also available with a vacuum advance canister to help improve economy. Order the model recommended for your vehicle and engine application.
( 328 )
$620.95
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 21 )
$999.95
On Sale
ACCEL SuperStock coils are excellent high-performance coils. They're designed with optimized low resistance and a high turns ratio, for higher energy output. This also results in quicker starts, improved throttle response, and more high-rpm power.
( 92 )
$65.89
$49.42
—
$79.09
FAST PS20 performance ignition coils feature a special E-core design, which loses less voltage, so more spark gets to your plugs. The coils also have large-gauge wire windings for maximum spark current and voltage, with better heat dissipation at high rpm. An insulated connector and high-tension tower protect against high-voltage arcing. They're also solid-epoxy encapsulated for shock and vibration protection.
( 12 )
$55.95
Do you need to upgrade your ignition system due to a recent Sniper EFI installation, but have no idea which option is best? Introducing Holley Sniper EFI HyperSpark distributors. These billet distributors use a hall-effect crank signal sensor, providing a noise-free RPM signal to the Sniper ECU. HyperSpark distributors include a patented clear installation cap that eliminates any confusion when installing the distributor. They're an easy plug-and play solution to add timing control and complete your Sniper EFI installation. Many options are available; choose the model recommended for your year/make and engine application.
( 124 )
$449.95
FAST PS40 performance ignition coils feature a special E-core design, which loses less voltage, so more spark gets to your plugs. The coils also have large-gauge wire windings for maximum spark current and voltage, with better heat dissipation at high-rpm. An insulated connector and high-tension tower protect against high-voltage arcing. They're also solid-epoxy encapsulated for shock and vibration protection.
( 4 )
$67.95
Get your points system working like new Mallory replacement condensers for their electronic and points style distributors contain special windings to protect your points from pitting, and moisture-proof seals to maximize ignition reliability.
( 8 )
$18.58
Our Summit Racing™ billet distributors provide reliable spark throughout the rpm range, so they'll deliver the performance you need, no matter what you drive--race car, street machine, or hauler. The affordable distributors have high-dollar features that outperform the competition, like a lightweight aluminum housing that's precision CNC-machined for strength and stability, polished steel shafts with sealed ball bearings for stable operation through 10,000 rpm, and a maintenance-free, high-output magnetic trigger for accurate and reliable performance. The distributors have a black alkyd cap and an adjustable mechanical advance, so you can precisely tune the curve to your engine setup. Some models also feature vacuum advance. An ignition box is required for use with Summit Racing™ billet distributors.
( 164 )
$238.99
—
$254.99
On Sale
Precise timing control—Holley EFI dual-sync distributors are built with two Hall effect sensors for crankshaft and camshaft signals. The distributors can be used as just a crankshaft speed input or provide a camshaft sync signal for sequential fueling operation. They're also useful for crank and cam signals when running coil-on-plug applications. Dozens of models are available; order the one recommended for your vehicle/engine application. Some features of Holley EFI dual-sync distributors include: * CNC-machined billet aluminum housings with integrated LEDs for easy setup * Hardened steel distributor gear * Precision-machined shutter wheels that ensure accurate timing—even at very high RPM * Designed to be plug-and-play with Holley systems, but may be used with other EFI systems that support Hall effect crankshaft and camshaft sensors * Housings are available in a variety of finishes
( 37 )
$579.95
—
$649.95
MSD Pro-Billet crank distributors are built specifically for racing engines with almost no room for a distributor, due to tunnel rams or blowers. These units are equipped with a special low-profile crab-style distributor cap, allowing them to fit into extremely tight areas. The housing features two optional O-rings at the bottom that improves oil control by preventing oil pressure loss. Also, a small oil bleed hole (located in the base) sprays oil on the distributor and camshaft gears to prevent excessive wear. Since these are racing distributors, there is an adjustable slip collar to make up for engines that have had the distance between the mounting surface and the gear modified. Crowning the Pro-Billet crank distributor is MSD's own crab cap. This incorporates spark plug-style terminals for a better connection and grip to the plug wires. Order the model recommended for your vehicle and engine application.
( 20 )
$499.95
PerTronix Flame-Thrower magnetic trigger billet distributors are perfect alternatives to the more expensive distributors that competitors offer. These distributors feature a precision magnetic pickup coil and reluctor for extremely accurate signaling at low and high rpm. An over-molded magnetic pickup coil supports windings, while providing excellent resistance to corrosion. Tyco Mate-N-Lok connectors work with most ignition system harnesses. A specially engineered reluctor made from lightweight FC-0208 alloy offers superior dimensional stability for symmetrical spark separation. PerTronix Flame-Thrower magnetic trigger billet distributors are compatible with most capacitive discharge ignition boxes.
( 12 )
$340.55
—
$379.30
If your points eliminator module happens to burn out, or you're performing maintenance to your system, be sure to have the right parts for the job--ACCEL points eliminator replacement models. These modules are direct replacements for those in your ACCEL points eliminator kit.
( 15 )
$99.95
Summit Bucks
FAST XDi EZ-RUN distributors are convenient packages that save time and space. These units do not require an ignition box to fire the coil, and their standard-size caps offer more firewall and manifold clearance than HEI-style distributors. XDi EZ-RUN billet distributors feature mechanical and vacuum advance for easy setup and use. They also feature a built-in electronic module that can directly fire an ignition coil, while delivering accurate, dependable, and maintenance-free operation. Ideal for both carbureted and EFI conversion engines, EZ-RUNs are a perfect choice for daily drivers, musclecars, and street rods. FAST XDi EZ-RUN distributors are available for most domestic V8 applications. Choose the model designed for your year/make and engine application.
( 2 )
$382.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
