Availability
Showing In Stock Items. Show All 6 Items.
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 21 )
$999.95
When you're making extreme cylinder pressure with boost or nitrous on an inductive coil-per-plug ignition, lack of spark energy means you're leaving horsepower on the table. MSD Pro 600 CDI ignition kits with high-output coils answer this need. The Pro 600 CDI ignitions provide unrivaled spark energy and dependability. They have built-in protection for accidental reverse battery connection, over temperature protection, and LED diagnostics that can identify an issue with individual coils should a problem arise. They also feature a programmable power setting to allow racers to switch between 250 to 400 millijoule outputs, or the industry-leading output of 680 millijoules via an activation wire or software, meaning that you can turn it down for the long haul and then set it to kill mode at the strip, making the Pro 600 ideal for a Drag Week-style car and really any no-compromise vehicle. Perfectly complementing the Pro 600 ignition box in these MSD kits are high-output 8280 ignition coils, replacing the extremely capable 8232 coils used in the 8-channel capacitive discharge ignition kits. Available in red or black, the 8280 coils have the goods to back up their aesthetics with increased peak spark current, overall spark energy, and greater thermal efficiency. Designed for coil-near-plug engine management systems, the PRO 600 is also capable of easily converting any distributor-type ignition into a coil-near-plug system. Additional features and specifications: * Eight outputs of up to 680 millijoules of energy * All necessary wiring harnesses included * Continuous 600 millijoules operation without risk of failure from overheating * High-efficiency Alternating Current (AC) power delivery means less voltage draw from your battery or charging system * Over 50 kV output voltage when used with MSD suggested coils * Spark duration of greater than 300 microseconds * 6 V minimum required for starting and running * 12 V minimum required for 600 millijoules operation * Maximum operating voltage of 22 V * Direct plug-in to Holley EFI systems * Compatible with most EFI systems, including 5 V or 12 V drivers * Plug-in interface with MSD Power-Grid, Davis Profiler, and OEM LS-style coil harness * Diagnostic LEDs help troubleshoot issues should they arise * On-the-fly power output selection wire, selectable between low power and high power * Fits most coil-per-plug engines up to eight cylinders (including four and six cylinders) * Approved for NHRA Pro Mod Class
Not Yet Reviewed
$2,499.95
The new Ultra 6AL Plus ignition boxes deliver full MSD power in a compact, lighter package! The Ultra 6AL Series continues to use a high-speed controller that can make extremely quick compensations to the output voltage, multiple spark series, timing and rpm limits, while maintaining precise timing and accurate rev limiting. The circuits and controller of the MSD have been thoroughly filtered to create protection against Electro Magnetic Interference (EMI). Ultra 6AL Series features a capacitive discharge ignition design. (The majority of stock ignition systems are inductive ignitions, in which the coil must store and step up the voltage to maximum strength in between each firing. At higher RPM, since there's less time to charge the coil to full capacity, the voltage falls short of reaching maximum energy—which results in a loss of power or top end miss.) MSD Ultra 6AL Plus ignition box details: * High conversion efficiency ensures minimal heat generation and maximum spark energy output with less current draw from the battery * High RPM operation and maximum output using the Blaster HVC, PN 8252 or HVC II, PN 8253 * Powerful capacitive discharge of multiple sparks improves performance * Consistently high spark energy of 135mJ to 150mJ for every firing, from idle to redline RPM * Increase spark series duration lasts for 18 of crankshaft rotation * Easily installs on 4, 6, 8-cylinder engines with distributors * Operates on most 7 to 28 volt electrical systems * Connects to points, magnetic pickups, and hall/crank input distributors * Bluetooth connectivity to mobile app interface for settings and monitors * MSD CAN communication for easy connectivity to MSDView using a CAN MSD Hub and Power Grid USB or CAN-USB Bridge 89982 product * Straight USB port to easily connect to MSDView using a laptop * Fully protected against an open coil, shorted coil and open load * Compact design full MSD power * Quickens throttle response and improves starting * Tach Output * Launch, Burnout, and Step Retard activation inputs available. This ignition box has a built-in tri step RPM rev limit controlled by the mobile app * Mobile app available settings: Step retard value, Launch RPM value, Burnout RPM value, Max (Race) RPM Value * Programmable Step Retard: On Ramp time, Off Delay, Off Ramp Time, Engine RPM for activation * Programmable Start Retard through rotary switches: 0, 10, 20 degrees * Programmable cylinder selection through rotary switches: 4, 6, and 8 cylinders * Alerts and monitors available * High level of security connection from phone to Ignition box (encryption), including sequence in push button implementation * Maximum programmable retard of 35 degrees * Programmable timing curves in 2D plots or 3D tables (RPM vs Timing vs MAP Pressure); you can plot the 3-D graph and edit a table 20x20 either from mobile app (phone) or from MSDView (laptop) * Programmable Launch Timing (seconds vs degrees after launch wire activation) * MAP sensor interface up to 400 kPA (58 psi / 4 Bars) * Capable of programming cylinder selection and start retard without a computer or app for old school racers (like 6425 or 6428 box)
( 7 )
$467.95
Dyna 2Ki Programmable Ignitions not only add to, but extend, many features of the Dyna 2000 modules with a completely new design that fits under the cam cover. Every time power to the ignition is switched on, the 2Ki checks to see if the coil is shorted, mis-wired, or of the wrong type. If an error is detected, the 2Ki will immediately switch off and issue a warning. After starting, the 2Ki continuously monitors the status of the coil and wiring. All 2Ki ignitions are PC programmable: * 8-point fully-definable wide-open throttle curve * 8-point fully-definable part-throttle curve * Rev limit programmable in 50 rpm steps * Programmable dead cranking revs 0-10 * Programmable rear cylinder offset, total of +/- 10 degrees Data recording functions: * Total engine hours * Time at wide-open throttle * Number of engine starts * Longest time operating at wide-open throttle * Maximum rpm * Seconds near rev limit * Statistical analysis of time at rpm Additional features and benefits include: * Single-fire operation down to zero rpm for easier cranking and kicking * Operates in all combinations of single-fire or dual-fire with single plug or dual plug heads (when used with appropriate coils) * Eight advance curves to cover a broad range of engine builds and riding styles * Over-rev protection adjustable from 6000 to 7500 rpm * Adjustable timing retard for nitrous and turbo applications * VOES indicator; shows the status of the VOES switch, also indicates when retard mode is active * Built-in tach driver delivers stable tach signal even during rev limiting; can be used to activate shift lights, auto shifters, and other accessories * Easy static timing with built-in timing indicator (no timing light required) * Intelligent over-current and short circuit protection * Active dwell control continually adjusts coil current to maintain maximum spark energy up to redline while eliminating coil stress caused by overcharging at idle * High-efficiency design reduces battery draw for easier cold weather starting and lower charging system load * Ruggedized output--cannot be damaged by broken or disconnected spark plug wires * Over-voltage protected against momentary spikes (positive and negative) as well as surges caused by faulty voltage regulators or quick-charge battery boosters * Harness constructed with TXL cross-linked polyethylene automotive wire for exceptional resistance to abrasion, heat, and chemical attack * High-temp glass-braid jacket further increases the toughness of the harness and provides a tight, clean appearance * Wire colors closely match the factory harness for error-free installation * Manufactured with premium-quality components designed for operation in a high-temperature, high-vibration environment * One-piece aluminum housing and thermally-conductive epoxy encapsulation provide superior heat dissipation and outstanding shock, vibration, and moisture resistance * Advanced microprocessor technology * Quartz crystal accuracy.
Not Yet Reviewed
$418.99
Clearance
Harness the power of spark energy with ACES Fuel Injection Full House Multi-Coil Ignition Systems! Designed for coil-near-plug engine management systems, such as ACES Fuel Injection Jackpot EFI, GM LS platforms, and most other EFI systems, the Full House ignition helps make unrivaled spark energy and dependability. The Full House has built-in protection for accidental reverse battery connection, over-temperature protection, is fully waterproofed, and has LED diagnostics that can identify a problem with individual coils should one come up. A programmable power setting using the included high-resolution hand-held programmer allows users to switch between 250 to the industry-leading output of 750 millijoules via the hand-held wire or software, making the Full House ideal for street driven race cars. Turn it down for the cruise, and then set it to power mode at the track. Whether it's Pro Mod, Pro Street, or a sled dragging pull wagon, if you need to power your 8-coil ignition reliably, the ACES Fuel Injection Full House is the system for you! Additional features and specs: * 32-bit Power Architecture based MCU for automotive powertrain applications * Robust shielding for anti-interference, high stability hardware and software design * Real-time programmable ignition curve * Hand-held displays calibration data and all parameters in real time * Spark energy is adjustable by the full color, touch screen hand-held and the included ACES laptop tuning software * Eight channels ignition control with over 750 mJ spark energy * High-efficiency alternating current (AC) power delivery * Over 50 Kilovolts output voltage to drive ACES performance coil * Primary voltage over 565 V * Spark duration of greater than 300 microseconds * Operating voltage from 6-22 V * OE Spec waterproofing * Direct plug-in to Jackpot EFI systems * Compatible with most EFI systems using 5 V or 12 V drivers
Not Yet Reviewed
$1,499.99
$1,299.50
PerTronix Ignitor® solid-state ignition systems deliver more energy with greater timing accuracy. The secret lies in the trigger magnets, which spin with the rotor and operate a switching module that requires no external control box. These systems are immune to heat, oil, and debris—and install in about 15 minutes with only two wires to connect. They come with a switching module, hardware, and instructions. Ignitor® is an ideal choice for collector car restoration because it fits entirely under the distributor cap.
( 997 )
$141.00
—
$161.37
Modal Header