Availability

2 Results Found For "kit"

Showing In Stock Items. Show All 2 Items.

Individual Parts

Part Groups

Results 1 - 2 of 2

MSD Direct Ignition Systems

The MSD Direct Ignition System (DIS) controller greatly simplifies the conversion from conventional distributor-type engines to a coil-per-plug configuration. Benefits include the elimination of distributor cap and rotor wear; reduced spark energy losses caused by long spark plug wires; and the ability to optimize your ignition tuning parameters. The integral 2.5 bar MAP sensor and optional temperature sensor input mean you get the most power and reliability out of your naturally aspirated or forced induction engine. Nitrous-fed engines benefit from the included Step Retard feature. Drag racers will appreciate the 2-Step rev limiter and Launch Retard features. Real-time DIS configuration and tune-up changes are a snap with easy-to-use MSDView software. Thanks to the real-time monitor feature of MSDView, and 8 MB of internal data storage in the DIS controller, data monitoring and logging have never been easier. The clearly labeled wiring harness, along with a full line of supporting components and accessories, take the difficulty and guesswork out of converting traditional distributor-type engines to a modern and efficient coil-per-plug ignition system. Features include: * Easily convert to a coil-per-plug ignition system * Pre-programmed timing maps * Fully programmable 2D and 3D timing maps provide complete timing control * Individual Cylinder Timing (ICT) allows precise tuning * Built-in 2.5 bar MAP sensor for boosted applications * Optional temperature sensor input to control timing based on temperature * Fully potted electronics and sealed connectors for maximum durability * Easily programmable through a Mini-USB communication port * Programmable max rev and launch RPM limiters provide engine protection * Consistent holeshots thanks to programmable launch timing retard * Single timing step retard ideal for pulling timing for nitrous applications * On-board data acquisition

4.0 out of 5 stars ( 5 )

$1,749.95

—

$1,999.95

FuelTech FTSPARK GEN II Ignition System

The FuelTech FTSPARK GEN II is an extremely high-energy Capacitive Discharge Ignition (CDI) system designed to meet the highest spark requirements for racing. It's developed for high-horsepower combinations and test-proven on 5,000+ horsepower engines! Compatible with any ECU on the market, this system is able to generate a spark with up to 750mJ (mJ=mili Joules) of energy—and is capable of firing the spark with 140 amps of current in the coil primary. With these features, FTSPARK generates a spark with approximately 5x more energy and 10x more current compared to a SparkPRO, ensuring a burn in any condition, especially in extremely rich air/fuel ratios. Models are available for 4-, 6-, or 8-coil applications. Technical description: * Programmable energy via CAN or digital input to adjust the energy level; - 475 V in the primary of the coil, which helps to prevent interference in the system * 140 amps of current in the primary of the coil with Racing CDI FuelTech coil for FTSPARK 750mJ * CAN communication with FuelTech PowerFT ECUs for diagnostic and datalogging * Automotive connector with gold-plated terminals * Serial bus (1 wire) allows the use of only one ECU output that triggers all ignition outputs (only with PowerFT) * Anodized aluminum and plastic case * Maximum working temperature: approximately 212 degrees F * Supply voltage for full power: 14-26 V. Minimum voltage for starting 8 V * Maximum operating frequency: 670 Hz * Compatible with other ECUs on the market. Check compatibility of your ECU with FuelTech tech support Contents of package: * One FTSPARK (GEN II750mJ or EXTREME) module * Installation and operation manual * Mounting hardware kit (4 rubber mounts, 8 washers and 8 nuts)

Not Yet Reviewed

$1,699.00

—

$2,099.00

1

Page 1 of 1