Availability
MSD Blaster coils put out 45,000 V, which are 15,000 more than stock. They also have an oil-filled metal canister and will fit stock mounting brackets.
( 431 )
$54.45
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 21 )
$999.95
GM performance fans will be geeked to learn about MSD's direct plug-in 2-Step launch controls for LS engines. These units are easy to install with factory-style connectors for a splice-free installation. When you're staged, you can hold the pedal to the floor, while the rpm stays at a consistent level, producing consistent launches.
( 85 )
$349.95
On Sale
Do you need to upgrade your ignition system due to a recent Sniper EFI installation, but have no idea which option is best? Introducing Holley Sniper EFI HyperSpark distributors. These billet distributors use a hall-effect crank signal sensor, providing a noise-free RPM signal to the Sniper ECU. HyperSpark distributors include a patented clear installation cap that eliminates any confusion when installing the distributor. They're an easy plug-and play solution to add timing control and complete your Sniper EFI installation. Many options are available; choose the model recommended for your year/make and engine application.
( 120 )
$449.95
—
$499.95
On Sale
ACCEL Performance replacement distributors are perfect for your daily driver or street machine. They're built with all-new components and high performance ACCEL electronics. Each model's design features the materials and accessories that make for an easy installation while providing the fit, form, and function you need. Order the ACCEL Performance replacement distributor designed for your engine when you need a quality substitute or want better performance.
( 146 )
$212.95
$125.95
—
$465.95
Replace your stock LT1 Optispark distributor with our all-new Summit Racing™ LT1 Optispark I or II distributors. These distributors feature an aluminum housing with heavy-duty oilite bushings, and a glass-reinforced cap with high dielectric strength and aluminum terminals.
( 121 )
$240.99
—
$261.99
PerTronix Ignitor® solid-state ignition systems deliver more energy with greater timing accuracy. The secret lies in the trigger magnets, which spin with the rotor and operate a switching module that requires no external control box. These systems are immune to heat, oil, and debris—and install in about 15 minutes with only two wires to connect. They come with a switching module, hardware, and instructions. Ignitor® is an ideal choice for collector car restoration because it fits entirely under the distributor cap.
( 988 )
$117.95
—
$127.45
Finally, all-out performance distributors to replace the OEM GM LT1 Optisparks--MSD's Pro-Billet LT1 distributors. They feature a precision-machined billet aluminum housing that fits in place of the factory piece, a new pickup assembly, a trick timing adjustment mechanism, and a new MSD distributor cap and rotor. The pickup is an advanced optical encoder that has proven to be very reliable and stable through extreme rpm and conditions. The rotor is bolted to a drive assembly that is indexed to the shaft, and is stabilized through the use of a large ball bearing assembly. The distributors use an adjustment screw to advance or retard the timing by up to 5 degrees.
( 64 )
$799.95
Get more power from a high-energy ignition than you ever expected with a brand new Summit Racing™ blueprinted HEI distributor. They feature a 50,000 V coil, medium weight advance springs, and an aluminum housing. The distributor shafts are guided by precisely aligned bushings for durability in extended street use, and most models include an adjustable vacuum advance. Separate advance springs are available, so you can fine-tune to your hearts content. Be in it to win it—with the Summit Racing™ blueprinted HEI distributor designed to fit your application.
( 1212 )
$262.99
On Sale
Precise timing control—Holley EFI dual-sync distributors are built with two Hall effect sensors for crankshaft and camshaft signals. The distributors can be used as just a crankshaft speed input or provide a camshaft sync signal for sequential fueling operation. They're also useful for crank and cam signals when running coil-on-plug applications. Dozens of models are available; order the one recommended for your vehicle/engine application. Some features of Holley EFI dual-sync distributors include: * CNC-machined billet aluminum housings with integrated LEDs for easy setup * Hardened steel distributor gear * Precision-machined shutter wheels that ensure accurate timing—even at very high RPM * Designed to be plug-and-play with Holley systems, but may be used with other EFI systems that support Hall effect crankshaft and camshaft sensors * Housings are available in a variety of finishes
( 35 )
$499.95
—
$579.95
Our Summit Racing™ billet distributors provide reliable spark throughout the rpm range, so they'll deliver the performance you need, no matter what you drive--race car, street machine, or hauler. The affordable distributors have high-dollar features that outperform the competition, like a lightweight aluminum housing that's precision CNC-machined for strength and stability, polished steel shafts with sealed ball bearings for stable operation through 10,000 rpm, and a maintenance-free, high-output magnetic trigger for accurate and reliable performance. The distributors have a black alkyd cap and an adjustable mechanical advance, so you can precisely tune the curve to your engine setup. Some models also feature vacuum advance. An ignition box is required for use with Summit Racing™ billet distributors.
( 163 )
$189.99
—
$265.99
Manufacturer Rebate
PerTronix Flame-Thrower plug and play billet distributors with Ignitor II® module are designed to provide maximum ignition performance and easy installation, all at a price that you can afford. They allow you to upgrade your outdated points or stock electronic distributor with a performance-proven unit. The distributors feature the patented Ignitor II® electronic ignition module and a CNC-machined 6061 T-6 polished billet housing. PerTronix electronics are compatible with any inductive ignition system coil, but high-rpm performance can be improved when they are used with the low-resistance (0.6 ohm) Flame-Thrower II coil. Their stand-alone design makes them plug-in units that require no additional ignition, but they are compatible with multi-spark CD ignition boxes for outstanding versatility. Additional features include a tempered shaft, an upper roller bearing, and an oil-impregnated sintered bronze lower bushing. The PerTronix Flame-Thrower plug and play billet distributors with Ignitor II® module come with a factory-set performance curve, a mechanical advance limiting adjustment, and a small, high-dielectric strength cap and rotor for applications with little clearance.
( 343 )
$364.95
—
$437.45
PerTronix Ignitor lobe sensor solid-state ignition systems replace breaker points and troublesome factory units with a dependable, self-contained, and maintenance-free electronic ignition system. The Ignitor has been called the "stealth" ignition because of its quick installation and nearly undetectable presence under your distributor cap. There is no "black box" to clutter the engine compartment. PerTronix Ignitor has proven itself in applications ranging from race cars to tractors. Order the model recommended for your vehicle, engine, and distributor application. Product features: * Delivers twice the voltage to your spark plugs—increasing horsepower, fuel economy, and spark plug life * 2:1 improvement over "points" in current fall time for increased coil output * No points to burn or moving parts to wear out * No magnetic sleeve or ring needed; uses existing distributor lobe for sensor trigger * Epoxy molding makes the module impervious to dirt, oil, grease, and moisture * Stable timing—no need for any adjustments * Will trigger most multi-spark CD ignitions * Available for 6 and 12 V negative and positive ground systems
( 204 )
$119.66
Summit Racing™ Electronic Distributor Conversion kits allow you to Convert your factory single point distributor to a true 1 wire solid state ignition. Simply remove and replace your points and condenser with the solid state breakerless ignition module. Simple stealth 1 wire hookup is perfect for 100 point type restorations as it is undetectable. Never deal with breakdowns or adjusting worn or burned points again with a Summit Racing™ Electronic Distributor Conversion kit. • 1 Wire Hook-Up, just connect to the original points wire • Completely stock appearing • Fits inside 57-74 Delco Window cap distributors • Auto-standby prevents coil damage or dead battery if the ignition is accidentally left on • Active dwell control maintains high rpm spark energy while reducing coil heating at idle. • Hall effect rotary-vane sensor design compensates for worn bearings and distributor end play. • Magnetic sensor is unaffected by oil, dirt or other contaminants, unlike optical systems. • Over-voltage/over-current protected against damage from high amp battery chargers, reversed battery, or improper wiring • No distributor modification, disassembly, or removal is required , use SUM-RP20594 For New Repl. Black Ground Wire To Finish The Conversion.
( 9 )
$167.99
Not ones to leave well enough alone, the engineers at PerTronix set out to improve upon their highly successful Ignitor® ignition conversion systems. The Ignitor II® conversion systems have all of the same quality features as the original Ignitor®, plus a powerful microprocessor controller to deliver, on average, 4x more available energy between 3,000 and 5,000 rpm than standard ignition systems. They're an ideal choice for collector car restoration because they fit entirely under the distributor cap. Order the model recommended for your year/make, distributor and engine application. Features include: * Compatible with 12 V negative ground systems and any induction coil * High-rpm performance is improved when used with the PerTronix Flame-Thrower II super low- resistance (0.6 ohms) 45,000 V coil * Adaptive dwell maintains peak energy throughout the entire rpm range, reducing misfires while improving engine performance * Develops, on average, 2x more available plug voltage * Peak current level is reached just prior to spark for maximum energy without heat build-up, increasing coil and module life * Never change points again * Adjusts spark timing at higher rpm to compensate for the inherent electronic delay * Senses startup and develops more energy for quicker, easier starting * Built-in reverse polarity and over-current protection shuts down the system, preventing component damage * Cannot be used with solid core spark plug wires; suppression-style or spiral-wound spark plug wires must be used
( 290 )
$152.66
—
$181.45
MSD HEI coils increase spark energy when used with MSD HEI HEAT modules. Now you can replace your stock coil with these high-energy unitized coils for HEI distributors. They have low-inductance, high-temperature windings which charge the coil faster to give you increased spark energy at higher rpm. The premium epoxy filled construction is designed to withstand harsh race applications, as well as the wear and tear that daily usage dishes out, and still deliver more spark energy to the spark plugs.
( 35 )
$122.95
MSD Digital GM high-energy modules with rev limiters allow you to adjust the rpm limit between 5,000 and 9,000 rpm. True high-performance modules built for HEI distributors, they produce 50 percent higher coil drive currents than the stock module. This saturates the coil faster, which gives you more spark energy at top speeds. The results are increased horsepower and rpm range, and improved starting. When used with MSD's HEI coil, these plug-in modules create a potent high-energy spark to 9,000 rpm. MSD GM HEI modules replace all 4-pin modules used in HEI distributors with a vacuum advance canister. They can be used with factory, aftermarket, or MSD HEI distributors.
( 66 )
$177.95
Replace your stock HEI module with Davis Unified Ignition Dyna-modules for a crisper, smoother running engine. They have more electronic dwell than your stock, so the coil saturates longer and produces a more intense spark. Dyna-modules are available in different pin quantities to meet your application, and mount easily on the side of your distributor housing with minimal wiring. Quicker starting, better throttle response, and more low-end power can be gained with Performance Distributors Dyna-modules.
( 121 )
$69.99
—
$112.50
On Sale
MSD Pro-Billet Ready-to-Run EFI distributors are the perfect upgrade when you start making serious power with your EFI Ford or Chevy. They use a stock-style trigger pickup and come with plug-in connectors. Installation is simple by removing the stock distributor, then plugging in and bolting the new one in place! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. These distributors will smooth out the engine's idle, improve starting, and perform at a much higher rpm. Their housings are machined from billet aluminum, using state-of-the-art CNC mills and lathes. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing for accuracy through the entire rpm range. Chevy models also feature an extra-long sintered bushing at the bottom and an extra oil tract machined into the bottom of the housing for improved lubrication. The tract delivers oil directly to the cam and distributor gears. All of the shafts receive a QPQ coating for low friction wear, and resistance against corrosion from humidity and ozone buildup. The Chevrolet models have also been tested by the Underwriter's Laboratory, and are certified to meet or exceed safety standards for marine ignition systems as set by the U.S. Coast Guard.
( 91 )
$499.95
MSD Pro-Billet distributors share the same CNC machining techniques as the rest of the MSD distributor line. They feature a housing that's machined from high-quality 6061-T6 aluminum for durability and show-quality looks. Their oversized shaft receives a QPQ coating for friction reduction and corrosion resistance, with the added strength of two sealed ball bearings that guide the shaft accurately at well over 10,000 rpm. An extra-long sintered bushing replaces the ball bearing at the bottom of Chevrolet models. TIG-welded on top of the polished steel shaft is MSD's accurate mechanical advance assembly. The weights are supported by nylon pads that allow the advance to operate smoothly throughout the rpm range. For all-out racing, the advance mechanism can also be easily locked out. To accurately trigger the ignition, a high-output magnetic pickup is bolted to the base. This pickup produces a precise trigger signal that will never vary more than one degree at any rpm. A durable gear is installed for performance applications, and an MSD red cap with brass terminals and race rotor is supplied. They're available in standard and small diameter models for applications with limited clearance, and require the use of a separate ignition box such as an MSD 6, 7, 8, or 10 Series ignition.
( 399 )
$517.95
MSD Blaster coils give your GM maximum voltage output! With windings and construction similar to MSD's Blaster 2 coils, these have an increased turns ratio, plus lower primary resistance than your stock coils. The Blasters will work with stock GM coil ignition systems, as well as MSD-equipped cars and trucks. Looking to get a little more output voltage from your GM ignition system? Just bolt in one of these MSD Blaster Coils.
( 87 )
$78.15
These PerTronix Ignitor III® solid-state ignition systems feature an adaptive dwell that maintains peak energy throughout the entire rpm range, reducing misfires while improving engine performance. Peak current level is reached just prior to spark for maximum energy without the heat buildup, increasing coil performance and module reliability. They adjust spark timing at higher rpm to compensate for the inherent electronic delay, sense startup, and develop more energy for quicker, easier starting. The PerTronix Ignitor III® solid-state ignition systems have a built-in LED for user feedback confirmation of the rev limiter setting.
( 82 )
$179.10
MSD puts their years of experience to work in making these top-notch iron distributor gears. Their high grade, ductile iron is micro polished for a smooth and scuff-free finish then Melonite QPC coated to reduce friction and initial wear. Excessive clearance causes timing fluctuation throughout the rpm range, resulting in lost horsepower, so MSD also designed these oversized gears for tighter mesh between the camshaft and distributor drive gears.
( 58 )
$59.25
Ensure that you have the finest distributor cap available by using one of these MSD replacement distributor caps. They're designed with performance in mind, are molded from a high-quality, voltage-insulating material, and use low-resistance terminals for maximum conductivity .
( 195 )
$46.09
—
$72.69
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
