Availability
These Pacer Performance LED logic modules filter out turn signal input on all vehicles that use combined brake and turn signal lamps. These modules are required when using a single light as a third LED brake light. Works on most domestic models.
( 10 )
$14.99
Morimoto X3B LED third brake flash modules can be added to your X3B brake light setup to automatically pulse the brake light optics 3x before staying on when you step on the brake pedal. Though the standard optics and powerful 3W LEDs in the X3B brake lights are already highly visible day and night, the addition of this module makes sure that followers will notice when you step on the brakes. This feature has become standard on many of the most modern trucks and cars. The X3B Rapid Flash module is 100 percent plug-and-play with the Morimoto X3B brake lights and can be connected in seconds. It is not compatible with other aftermarket products or OEM units.
Not Yet Reviewed
$36.00
Denali PowerHub2 power distribution modules allow you to safely connect up to six electronic devices to your vehicle in a clean, professional manner—by consolidating all the battery connections and fuses into one compact housing. The modules feature six fused accessory circuits with both positive and negative terminals. Each circuit is rated for up to 15 amps, while the whole PowerHub unit is rated up to 30 amps. The six outputs can be individually set as "always on" or "switched," which will turn your accessories on/off with the ignition of the motorcycle.
( 2 )
$169.99
Over time, daytime running lamp modules typically wear from continuous use, ultimately affecting the headlamp's operation. Dorman's solution is to remedy the problem with quality replacement daytime running lamp modules. Dorman offers module replacements in applications to conveniently restore your car, truck, or Jeep's headlamp operation for safe driving--so you can see and be seen!
Not Yet Reviewed
$82.99
Moroso electric float switches allow single-point detection of coolant high/low levels through a sidewall of your tanks using "normally open" or "normally closed" contacts. Wire these 30-watt-rated switches into your OEM low-coolant-level circuits or use them as switches for aftermarket coolant-level lights. They include a bung so that the level sensor option can be added by drilling and welding to the coolant tank. The combination of highly skilled craftsmen and highly accurate machinery guarantees that the tradition of quality continues with each and every one of Moroso's products.
( 1 )
$57.99
American Autowire memory retainer assemblies are an auto-resetting breaker that keeps your clock and tunes active, while still keeping the car from being started with the master disconnect switch off. Master disconnect switches are great for security, but you hate resetting your clock and radio presets every time you turn that switch. Creative car guys used to wire a low-amp fuse jumper to keep the basic systems on when the master disconnect switch was off, but every time you forget to switch it back to "on" before starting, the car the fuse would pop. These assemblies simply install between the two posts of the master disconnect switch to maintain the circuit for up to 2 amps continuous or 4 amps max load.
( 5 )
$32.30
—
$41.80
ARB LINX line pressure control kits are used in conjunction with the optional pressure control upgrade. The kits offer "set and forget" simplicity to tire inflation, as well as remote control over your airbag suspension. LINX kits are perfect for easy and accurate adjustment of tire pressures, or controlling a set of air bags with the wireless mobile display--whether inside or outside (up to 10 meters away) your vehicle. Take full advantage of the ARB LINX pressure control module, when you couple your ARB air compressor with their pressure control kits. ARB kits include: * Pressure regulator valve * Transducer * Wiring looms
Not Yet Reviewed
$295.00
ARB LINX air bag isolation kits provide the ability to independently adjust the pressure and ride height in each air bag. Leveling your vehicle from side-to-side becomes an easy on-display adjustment--perfect when loads are added unevenly to your vehicle. Take full advantage of ARB LINX air suspension module, and your air suspension, by adding these suspension isolation kits. Each of the kits includes solenoids and wiring loom.
Not Yet Reviewed
$200.00
Wire both right and left lights with Hagan Street Rod Necessities LED Hi/Lo modules. They are offered in two choices for 4 in. and under or 6 in. and over LEDs.
Not Yet Reviewed
$12.00
Dorman remanufactured totally integrated power modules require no programming. They restore your vehicle's electrical system to original operation, regulating proper voltage distribution to functions you invariably rely upon, including the windshield wipers, the headlamps, the radio, the climate control and much more. Made from high-quality materials to meet or exceed OE power modules.
( 30 )
$569.95
RedVision by REDARC provides an unprecedented level of control and automation to your truck, caravan, camper, RV or work vehicle. Control accessories such as lights, fridges, TVs and inverters via the physical screen or your Bluetooth connected mobile device. At just 1-inch thick with in-built smart fusing, the TVMS Rogue control module offers a small footprint, great for vehicles with limited space. Dimmable outputs make the Rogue RedVision system ideal for lighting and low-powered devices such as fridges and fans. When paired with a Manager30 and RedVision Display (both sold separately), TVMS Rogue provides real time and accurate state of charge, power input/output, and ambient temperature information. Two analogue tank level inputs offer accurate monitoring of multiple tanks, and the Rogue is compatible with most common tank level sensors. NOTE: TVMS Rogue is compatible with RedVision Display units (DISP4300-RC) manufactured from January 2023, serial numbers beginning with 23. Displays manufactured from July 22 to Jan 23 (serial numbers beginning 2207 - 2212) are upgradable.
Not Yet Reviewed
$679.00
ARB LINX vehicle accessory control modules offer a smart way to declutter your dash, while providing better control of your vehicle's accessories. Tailor made for off-roading and overlanding, LINX interface systems allow you to move your switches and buttons to a simple, sleek touchscreen for fingertip control, and include 6 pre-installed modules. ARB LINX vehicle accessory interface systems are built on expandable platforms, so they will continue to evolve your on and off-road driving experiences, both now and in the future. ARB LINX includes: * LINX display screen--was specifically designed to withstand the extremes of heat and cold. It has a metal coupling on the back to connect to gimbal mount. The display supports USB, Bluetooth, Wi-Fi, and GPS connectivity and complies with FCC, CE, and RCM certifications. * LINX controller--powers system and comes assembled with din rail on back to secure unit * USB charge cable--used to power and charge the LINX display, and provides the communications channel between the LINX controller and LINX display. * Wiring looms * LINX gimbal mount with magnets ARB LINX pre-installed modules include: * Front and Rear Traction * Compressor and Pressure Control * Battery Monitoring * Speedometer * Air Suspension Control * Accessory Switchboard
Not Yet Reviewed
$659.95
ARB LINX wiring harnesses are optional accessory wiring that will assist in integrating seamlessly with your vehicle and a LINX accesory interface.
Not Yet Reviewed
$14.00
—
$33.95
These Standard Motor Products replacement coolant level sensors provide the PCM with an analog input signal, along with an oxygen sensor, to go into the closed loop mode of controlling the fuel mixture. They are designed to provide actual engine temperature information to the PCM. The PCM then feeds the sensors a fixed reference voltage of usually 5 volts when the engine is on. The resistance in the sensors is high when cold, and drops as the sensors warm up, to alter the voltage signal back to the PCM. Are you experiencing temperature problems with your vehicle? Try one of these Standard Motor Products replacement coolant level sensors to eliminate any chance of problems.
( 4 )
$34.99
MSD relay modules are designed to be easily installed in most automotive electrical systems where a high amperage relay is needed. These relay modules are perfect use with high amperage electric fuel pumps and high CFM electric cooling fans. The relay housing comes with a labeled lid that snaps into place providing a clean installation and protecting the main power stud and triggers from contamination or accidental contact. MSD offers these relay modules with different channel outputs, select the model that's designed to meet your application needs. Features include: * 7 V to 20 V supply to fit a wide variety of applications * Independent 40A outputs, to supply power to most aftermarket fuel pumps and electric fans * Configurable single-wire activation with Ground (-) input or 12 V (+) input, with removal of the Tie-Bar * Removable cover for easy accessibility * Low-profile JCASE fuses provide ample protection in case of a short * LED status indicators, show you which channel is triggered at a glance
( 11 )
$57.49
—
$158.95
Holley trans-brake input protection modules allow for an ECU input to be safely connected directly to the 12 V side of the trans-brake solenoid. They are designed to protect the ECU input from damaging fly-back voltage, which occurs when the trans-brake is released. Not using one of them will cause damage to the ECU over time.
( 4 )
$59.25
On Sale
Hoop up your Atomic TCU with MSD Atomic transmission control module harnesses. They are designed to fit your specific transmission model and have the proper wiring connector for a direct fit.
( 7 )
$299.95
$164.95
—
$329.95
Digital Guard Dawg PBS-X modules add push-button start to vehicles with an existing alarm. It's the perfect solution for those who want to add the convenience and elegance of a keyless push-button start system to a vehicle which already has a high-end alarm system with traditional keyless entry installed. The system operates using your alarm's existing alarm remote transmitters—and eliminates the need to carry two different transmitters with you. PBS-X modules use a standard negative output signal found on all traditional alarms to activate and deactivate the system's push-button start functions at the same time your current alarm system arms and disarms. As you approach your vehicle and press the unlock button of your alarm transmitter, the Digital Guard Dawg PBS-X start button LED will illuminate. Just get in, place your foot on the brake and press the start button to fire up your engine!
( 4 )
$398.99
Digital Guard Dawg hands-free security modules are proven protection for your vehicle! This is the first RFID "hands-free" security system designed for any ATV, UTV, motorcycle, or any other 12 V vehicle. Using technology similar to RFID security systems found on many new luxury automobiles, the M-1 automatically arms and disarms your security system without ever lifting a finger. You simply carry a small RFID device called a "Dawg Tag" with you—and your security functions are all handled automatically whenever you walk away from or return to your vehicle. The Dawg Tag only allows your vehicle to be started when you are next to it. Dawg Tags are dual-mode (manual/automatic) and motion activated with over 6 billion codes. One tag can operate multiple motorcycles—and M-1's silent protection won't drain your battery like common alarms. Installation is quick with the M-1 module's simple 2-wire plus +/- harness.
( 12 )
$135.00
Aeromotive VaporWorx GM fuel module plugs with wiring pigtails feature genuine Delphi connector, terminals, and seals with 12-gauge/20-gauge XLPE cross-linked insulated wiring. Each of the wires are 12 in. long.
Not Yet Reviewed
$28.95
MechMan indicator light module connectors are for use on GM vehicles with MechMan alternators and equipped with a 2-pin regulator and a RVC (Regulated Voltage Control) sensor. Simply plug module into your vehicle's factory harness and tie out of the way. This will eliminate the check charging system code (battery light). These are especially popular for the customer who wants to bypass the RVC system so that they can run a stand-alone alternator. The reason for this is that when run in the factory form on these model vehicles there will be fluctuating voltage and normally, they will charge at a lower voltage. Although this is all normal since the PCM is controlling the voltage in order to acquire max fuel economy, some will opt to go with a standalone unit to acquire a higher and more stable voltage.
Not Yet Reviewed
$29.99
ARC relay modules are available in 1 through 5-position units and should be used to purge or stage solenoid operations for fuel pumps. These modules feature a plug-in fuse and 40 amp relay, which can be operated by switching to 12 V or GND.
( 2 )
$38.99
—
$312.99
ACDelco GM Genuine Parts HVAC blower control modules manage the temperature, air distribution, blower fan, and air conditioning functions in automatic climate control systems, and they are GM-recommended replacements for your vehicle's original component. These original equipment HVAC control modules have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
( 4 )
$72.99
—
$164.99
Why not add some "progressive" pizazz to your turn signals? Scott Drake sequential control modules can be used to wire any multiple lamp configurations on custom vehicle lighting projects. They're an easy and affordable upgrade for your Mustang—delivering results seen by every driver behind you. These programmable plug-and-play modules feature variable rate adjusters and color-coded wire harnesses. Projects that have separate brake and turn signal circuits require a sequential module for each circuit.
( 2 )
$184.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
