Availability
Showing In Stock Items. Show All 135 Items.
Add GM 6L80/90E transmission control to any existing vehicle utilizing a Terminator X Max ECU. A departure from traditional Holley EFI transmission control, the Terminator X Max ECU allows the ability to use 2007+ GM 6L80E and 6L90E transmissions by communicating via CAN with the internal TCM (Transmission Control Module). The supplied Holley EFI OBDII transmission tuning hand-held is used to adjust shift points, tire size and gear ratio. Terminator X V3 software provides the ability to dial in torque management to optimize the desired shifting characteristics when using a 6L80/90E transmission. The software also enables you to control the secondary shift mode within the transmission TCM and allows use of tap Up/Down shifting. Within Terminator X V3 PC Software: --- Virtual Torque Management Tables --- Virtual TPS Tables to dial in shift characteristics regardless of engine --- DBW and Timing torque reduction tables to create smooth shifts Within the Holley EFI OBDII Transmission Tuning Hand-held: --- Ability to read and clear TCM fault codes --- Ability to raise and lower shift points by MPH or RPM --- Support for Tap Up/Tap Down & Transmission's Secondary Shift Mode If you currently have a Terminator X ECU, upgrading to a Terminator X Max ECU can be easily done by plugging your main harness into the Max ECU and re uploading your existing calibration. Holley Terminator X MAX GM 6L80/90 transmission kit features: * Included TCM hand-held tuner with integrated wizard is required for setup in conjunction with the Terminator X 3.5 in. hand-held. Terminator X V3 software unlocks optional tuning parameters. * Plug-and-play with any engine controlled by a Terminator X Max ECU * Supports: Shift Mode - Tap Up / Tap Down, and torque management * Four loose wires: --- Power (Red): Supplies power to the transmission solenoids. This should be connected directly to the battery, or a constant battery source capable of supplying 5 amps --- Ground (Black): Connect to a good chassis/engine ground source --- Brake Switch (Light Blue/White): Wired to the brake light switch. This must be installed to a +12 V source (as most brake light switches are) --- Park/Neutral Safety (Yellow): Circuit for starter solenoid. When the transmission is in Park or Neutral, this yellow wire will be grounded (-). When the transmission is in gear this circuit will be open.
Not Yet Reviewed
$573.95
A faulty transmission control module can leave you stranded in a hurry—but ACDelco has a direct replacement for your vehicle application. Each module has been thoroughly tested to offer the same function and performance as the OEM parte. Restore smooth shifting with a new transmission control module from ACDelco.
( 1 )
$166.99
Clearance
ACDelco GM Genuine Parts transmission control modules are GM-recommended replacements for your vehicle's original components. They manage the operation of your vehicle's automatic transmission, and they contain the module and solenoid valves all in one unit. These original equipment transmission control modules have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
( 1 )
$115.99
$115.50
Pacific Performance Engineering heavy-duty PTO side cover plates are designed to add strength to the center of the transmission case and eliminate transmission oil seepage at the mating surface. They are manufactured from durable cast aluminum, and feature cooling fins double the surface area (60.74 sq. in.) when compared to stock (30.62 sq. in.). Thereby increasing heat dissipation from the transmission oil. The plates include mounting hardware and gaskets to complete the installation.
( 2 )
$80.99
Take the complexity out of wiring your Gen 4X 5.0L Coyote crate engine with a Ford Performance Parts control pack. Ford Performance Parts 2021-23 Coyote 5.0L control packs are available to run the crate engine with a Mustang 10R80 automatic transmission or a manual transmission. Choose the control pack needed for your build. Control packs feature: * PCM with unique Ford Performance calibration * Electronic throttle pedal eliminating cable routing issues * Unique harness replaces the stock body harness and is designed for custom vehicle installation * OBD-II port for trouble-shooting/code reading * Power distribution module, air box, air inlet tube, upper and lower radiator hoses, and HEGO sensors are included * Requires return-type fuel system
( 1 )
$2,462.99
FiTech presents Ultimate LS standalone ECUs. These self-learning ECUs are offered with and without transmission control. So if you're considering utilizing a factory intake, throttle body, and injectors, FiTech Ultimate LS standalone ECUs will get your engine ready for optimal performance.
( 50 )
$567.00
—
$1,202.00
Ready for standalone engine management at a budget price? Take control of your GM Gen V LT1, L83, or L86 engine with a Holley Terminator X Max GM Gen V LT direct injection kit! They're available to fit early non-WT drive-by-wire engines, as well as late WT drive-by-wire engines. Terminator X and X Max features and benefits: * Plug-and-play GM Gen V LT engine control, including GDI and VVT support * Ideal for swapping late model GM Gen V LT engines into vintage vehicles * 3.5 in. hand-held gets your engine running in no time with a step-by-step calibration wizard * GM LS and LT drive-by wire throttle body control (Terminator X Max only) * GM 4L60 and 4L80 transmission control (Terminator X Max only) * Included engine harness plugs directly into the factory LT DI injector sub harness * OEM Injectors supported, with part numbers provided in the handheld wizard or software * Genuine Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal – Cam Signal – VVT Status – Pump Control – and DI Injectors. This allows you to identify any critical engine issues at a glance * Built-in 1 bar MAP sensor, vacuum hose adapters included (1/8th, 1/4 and 3/16ths); or for Boosted applications, you can disable the internal MAP sensor, and utilize an external LT MAP sensor. The harness comes with the connector terminated, making the installation a snap * 4 inputs: 12 V, Ground, 5 V, and Frequency—for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (Fuel and Oil Pressure inputs are pre-terminated) * 4 Outputs: -- Ground -- PWM – for accessories such as fans, boost control, nitrous control, IAC kit, and more -- Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties -- Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR * Integrated data logging to the 3.5 in. hand-held SD card * Free EFI tuning software for complete control of your Terminator X powerplant Terminator X Max ECU Connections: * J1A - Main Harness Connector: This connector is primarily an "Input" connector. It contains all the sensor inputs and wide band oxygen sensor control. * J1B - Main Harness Connector: The second connector is the "J1B" connector (26 pin). This connector is the "output" connector. It has eight injector outputs and outputs for other devices. * MAP Sensor: Used on N/A applications, connect directly to full manifold vacuum port on the intake manifold. * Main Power: Connects to the Main Power Harness; these two wires MUST be wired directly to the battery terminals. * J3: Connection point for the drive-by-wire harness. * J4: Connection point for the transmission harness.
Not Yet Reviewed
$3,049.95
—
$3,549.95
Ford Performance Parts 2018-20 Gen 3 Coyote control packs are designed to run 2018-20 5.0L Mustang GT Coyote (Gen 3) automatic transmission engines with 10R80 Mustang GT 10-speed transmissions. They include a unique control pack harness, which replaces the stock body harness. These Ford Performance control packs were designed for performance enthusiasts who want the Gen 3 Coyote package in their own custom build. Includes: * PCM with Ford Performance calibration (requires return-type fuel system; not compatible with return-less-type) * Electronic throttle control accelerator pedal, eliminating throttle cable routing problems * OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis * Power distribution module * Mustang GT air box * Mustang GT air inlet tube * MAF sensor * Upper and lower radiator hoses * HEGO sensors
Not Yet Reviewed
$2,201.99
FiTech Ultimate TPI standalone ECUs bring an old GM TPI-controlled engine (L98, LB9) into modern times. These standalone EFI kits plug into all existing sensors on a GM TPI engine and provides complete control of the engine. From timing control to self-learning fueling, FiTech Ultimate TPI standalone ECUs deliver new life into the GM TPI engine.
( 9 )
$954.00
—
$1,060.00
Ford Performance Parts 2018 Coyote 5.0L control packs take the complexity and mystery out of wiring the engine. These engine management systems include a powertrain control module (PCM) with Ford Performance calibration, as well as an electronic throttle control accelerator pedal (which eliminates throttle cable routing problems). A unique control pack harness replaces the stock body harness and is designed for custom vehicle builds. It features an OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis. Mustang Coyote 5.0L control packs include a power distribution module, air box, air inlet tube, MAF sensor, upper and lower radiator hoses, and HEGO sensors. Additional notes: * PCM with Ford Performance calibration requires a return-type fuel system; it will not work with a return-less fuel system * Supercharged versions, modified engines, and modified applications require custom calibration * Installation of this PCM in a 2018 Mustang GT will result in a no-start condition * For 2011-14 engines, use control pack M-6017-A504VA * For 2015-17 manual transmission version control pack, use M-6017-504V * For 2015-17 automatic transmission version control pack, use M-6107-M50A
( 2 )
$2,266.99
Take the complexity and mystery out of wiring your late model, 2018-2023 5.0L Mustang Coyote engine with the Ford Performance Coyote 5.0L control packs! These engine management systems are designed to run Ford Performance 5.0L Mustang Coyote engines. 2018-2023 Coyote 5.0L control packs features: * Includes PCM with Ford Performance calibration * Includes electronic throttle control accelerator pedal which eliminates throttle cable routing problems * Unique control pack harness replaces stock body harness and is designed for custom vehicle builds * Features OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis * Includes power distribution module, air box, air inlet tube, MAF sensor, upper and lower radiator hoses and HEGO sensors * PCM with Ford Performance calibration requires return type fuel system, will not work with returnless fuel system * Supercharged versions, modified engines, and modified applications require custom calibration Note: Not for use with 2018+ F-150 Engines. Installation of this PCM in a 2018+ Mustang GT will result in a no-start condition.
Not Yet Reviewed
$2,394.99
HalTech Nexus R3 with universal wire-in harness kits are ideal for dedicated race cars, engine swaps and custom wiring jobs. The harness has a set of VCU connectors at one end and unterminated wires at the other. All the wires at the unterminated end are color-coded and clearly labeled. Connect your HalTech VCU to the terminated end and follow your wiring diagram for all the engine connections. Load your base map and you're ready to go! * Color-coded and labeled wires that match the detailed wiring diagram for a confusion free construction process. * The wiring diagram is accompanied by the full VCU manual and software located on the USB key provided with the VCU, or downloadable from the HalTech website. VCU OVERVIEW: * Nexus R3 combines the functionality of a power distribution module, a data logger, a wideband controller, and a state-of-the art engine management system in one powerful device HalTech calls a VCU (Vehicle Control Unit) * 4 x 25A (continuous) push-pull PWM capable (5 kHz) outputs (for power to injectors / coils, transbrake, thermofan, fuel pump) * 8 x peak/hold injector drivers (can be used as low side drive outputs) * 8 x low current ignition outputs (can be used as low side drive outputs) * 6 x low side drive outputs, PWM capable (DPOs) * 6 x push-pull /H-bridge outputs (8A, PWM capable), e.g. for electronic throttle * 11 x 0-5 V analog inputs with redundancy for electronic throttle and switchable 5 V pullup * Trigger and home inputs with differential inputs, adjustable thresholds and glitch filters * 6 x synchronous pulsed inputs, zero crossing or adjustable thresholds - cam sensor inputs, frequency inputs or 0-5 V analog inputs * 1 x on-board wideband controller, supporting NTK and LSU4.9 * 1 x on-board 4 bar MAP sensor * 2 x CAN ports with switchable termination * Suits: Engines with up to 8 cylinders or up to 4 rotors. Racing applications where advanced race features, data logging and power management control are required. * Includes: Nexus R3 VCU, SurLok connectors (red and black), WiFi antenna, mounting bolts, USB-C cable, USB-C dust cap, USB drive with NSP software. Nexus R3 universal wire-in engine harness.
Not Yet Reviewed
$2,799.00
Painless Performance OEM computers feature a stock calibration made for your specific vehicle while removing the VATS (vehicle anti-theft system) making them the perfect solution for your engine swap. Some tuning may be required for your specific application, but the computer will allow you to start your vehicle and get it to a local tuner. Make your engine swap easier with Painless Performance computers.
( 8 )
$199.99
Get ready to "Push the Boundaries" with HP Tuners CORE standalone engine control units! Created and designed for gearheads and craftsmen who need the utmost level of customization, CORE ECUs deliver superior control over your powerplant with many features that go beyond the constraints of factory ECUs. They provide all the necessary sensor interfaces, ignition drivers, injection drivers, and output drive stages required for total engine control. Bringing the CORE ECU to life is HP Tuners' VCM Live software, combining the diagnostics and calibration elements into a single, user-friendly interface. HP Tuners CORE ECUs are designed for all levels of LS swaps and high-performance motorsports builds. Currently CORE supports Gen 3 and Gen 4 LS engines with a 24x crank and 1x cam trigger along with 58x crank and 4x cam triggers. Drag, circuit, off-road racing; drifting, rally, or restomods, no matter what your high performance application, HP Tuners CORE ECU will provide everything you need for total control, performance, and ease of use. Order yours today. Key features: * Up to 16 injector control (fuel) and 8 coil packs (spark) * Sequential injection * Flex Fuel support * Dual throttle body capability * Two built-in Lambda controllers * Internal datalogging--up to 150 channels at 1kHz * 3 CAN bus networks (2 CAN and 1 HPT net) and ethernet connectivity * Turbo boost and anti-lag control * Single-stage On/Off and progressive nitrous control * Launch control * Map switching * A/C control, alternator control, etc.
Not Yet Reviewed
$1,999.99
Ford Performance Parts 7.3L gas engine control packs include components and harness to install a 2020 to present Super Duty 7.3L gas engine with a 10R140 automatic transmission in a vehicle. The unique control pack harnesses replace the production body harness designed for custom vehicle builds. These kits require use of a conventional return-type fuel system. Note: Installation of PCM in a production vehicle will result in a "no start" situation.
Not Yet Reviewed
$2,285.99
—
$2,396.99
Shifnoid Outlaw bump boxes allow for a smooth transition during the dragstrip staging process. These trans-brake controllers are critical to cars that need to rev up before final staging (such as turbo cars), but are also used by many non-turbo bracket racers. The ability to slide through the pre-stage beams and into the staged beams with precise tuning cuts down on rocking, bumping, and red light starts. These boxes are easy to use. Simple adjustments can be made to accommodate different tracks, power levels, and rpms. One-touch operation results in better focus, consistent launching, and improved reaction times.
( 1 )
$207.99
HalTech Nexus R5 VCUs feature innovative, yet user-friendly technology, setting a new market standard for engine management and power distribution systems. HalTech Nexus R5 VCUs are 5-in-1 tools; an ECU, a PDM, a high-speed Wi-Fi module, dual channel wideband controller, and a data logger--all natively interconnected with each other and all are programmable with one single piece of software. Features: * 18 Injector drivers * 12 Ignition drivers * 12 8A outputs * 4 25A outputs * 23 AVI * 10 SPI * 8 DPO * 2 Knock control * 2 DBW control * Flex Fuel Support * Inertial measurement sensor * 4-channel oscilloscope * 3 Independent CAN bus systems * Wireless communication * 150 channel, 1kHz data logging with 512mb of logging space * Dual channel O2 wideband controller capable of running LSU4.9 and NTK sensors * Automatic transmission control Nexus R5 kits include: * Nexus R5 VCU * SurLok connectors (red and black) * Wi-Fi antenna RP-SMA 108mm * Mounting bolts * USB-C cable * USB-C dust cap * USB drive with NSP software * Reverse mount VCU label * Quick-start guide and wiring diagrams
Not Yet Reviewed
$4,299.00
These performance modules from JET will improve the performance of your Ford car or truck with very little work. Perfect for vehicles with little or no modifications, they're programmed for power increases under hard throttle conditions such as towing and wide-open throttle. They offer a full range of DST programming of the air/fuel ratio, ignition advance, and transmission, and are fully track and dyno-tested to ensure the most possible power without affecting drivability or fuel economy.
( 45 )
$284.96
JET Stage 2 performance chips/modules have been programmed to deliver peak power increases under hard throttle conditions, such as towing and wide-open throttle. These modules offer a full-range of DST programming of the air/fuel ratio, ignition advance, and transmission, and are fully track and dyno tested to ensure the most possible power without affecting day-to-day drivability. Stage 2 power chips/modules must use the following for proper performance: * 180 degree thermostat * 91 octane or greater fuel * Free-flowing exhaust
( 109 )
$141.71
—
$292.46
HalTech's Nexus R3 ECU combines the functionality of a power distribution module, a data logger, a wideband controller, and a state-of-the art engine management system in one powerful device HalTech calls a VCU (Vehicle Control Unit). Product features: * 4 x 25 amp (continuous) push-pull PWM capable (5 kHz) outputs (for power to injectors / coils, transbrake, thermofan, fuel pump) * 8 x peak/hold injector drivers (can be used as low side drive outputs) * 8 x low current ignition outputs (can be used as low side drive outputs) * 6 x low side drive outputs, PWM capable (DPOs) * 6 x push-pull / H-bridge outputs (8A, PWM capable), e.g. for electronic throttle * 11 x 0-5 V analog inputs with redundancy for electronic throttle and switchable 5 V pullup * Trigger and home inputs with differential inputs, adjustable thresholds, and glitch filters * 6 x synchronous pulsed inputs, zero crossing or adjustable thresholds - cam sensor inputs, frequency inputs or 0-5 V analog inputs * 1 x on-board wideband controller, supporting NTK and LSU4.9 * 1 x on-board 4 bar MAP sensor * 2 x CAN ports with switchable termination * Offers an excellent solution for your engine management needs * Applications: Universal * What's in the box: (1) Nexus R3 VCU
Not Yet Reviewed
$2,399.00
Superchips Flashpaq F5 Pro tuners put your vehicle's tune in your hands. These handheld devices read stock vehicle files and load custom-tuned files built through HP Tuners custom tuning software (there are no pre-loaded tunes). Find your favorite HP Tuners dealer and work with them to build the perfect tune for your setup. F5 Pro devices will hold up to four custom tunes and monitor/log up to eight vehicle PIDs. No matter what aftermarket parts you've installed, you can deliver power levels designed specifically for the upgrades you have added to your ride. Superchips Flashpaq F5 Pro tuners feature high-definition color screens and were designed with simplicity and functionality in mind—making it easier than ever to select your custom power level and have instant horsepower gains and drivability improvements!
( 8 )
$630.95
Hypertech ThermoMaster Power Chips replace your stock PROM, which holds the settings for fuel flow and spark advance. This is a Stage 2 chip that optimizes the spark and fuel curves for max performance. The ThermoMaster Power Chip is designed for use with a 160 deg. thermostat and premium pump gas (91 Octane or better). Maximize the performance of your ride with a Hypertech ThermoMaster Power Chip!
( 30 )
$122.99
—
$230.99
Hypertech Street Runner Power Chips replace your stock PROM, which holds the settings for fuel flow and spark advance. This is a Stage 1 chip that improves the spark and fuel curves for better performance. It provides max power at wide-open throttle but does not affect the idle or part-throttle settings. This means your mileage and emissions aren't affected! The Street Runner Power Chip is designed for use on a stock vehicle using premium pump gas (91 Octane or better). Wake up your ride with a Hypertech Street Runner Power Chip!
( 40 )
$109.99
—
$219.99
On Sale
Holley Terminator X MAX engine management systems let you take control of your domestic V8 engine. They give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X MAX features real-time fuel learn, high-impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. Also, Holley offers the X MAX systems with either or both drive-by-wire (DBW) throttle body control or transmission control. All kits come fully loaded with base maps for common domestic V8 engine combinations to get you out of the garage and onto the road or track fast. Order the model recommended for your vehicle application. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors (will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM, and for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables can be used for any custom tables * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most V8 engines, as well as tuning and gauge display functions
( 89 )
$1,789.95
$1,163.95
—
$3,299.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
