Availability
Showing In Stock Items. Show All 156 Items.
ACDelco fuel tank pressure sensors are GM-recommended replacements for your vehicle's original components. These OE-style sensors help measure pressure changes within the fuel system. They are manufactured to fit many General Motors applications, providing the same performance, durability, and service life you expect.
( 4 )
$51.99
FAST MAP sensors, by monitoring intake manifold vacuum, measure the amount of load being placed on the engine. They relay engine load output to the ECU, which in turn adjusts fueling for optimum performance and economy. Choose between 1-bar, 2-bar, 3-bar, and 5-bar MAP sensors.
( 10 )
$131.95
Factory and aftermarket mass air meters can be a source of frustration for tuners. JMS Chip mass air modifiers filter the mass air signal, while also scaling the signal to extend the dynamic range of the sensor, cleaning up a noisy signal that could cause drivability issues. They feature a simple switch that allows you to choose between filtering the signal at idle or cruise, and a rotary switch to choose between 16 built-in levels of filtering--filter only as much as the signal needs to be cleaned. You can also choose to filter the signal based on the MAF frequency, or you can filter based on another input from a 0 to 5 V sensor. With seven unique filter ranges you can fine tune the filter to your problem area. JMS Chip mass air modifiers have advanced electronics housed in aluminum cases, complete OEM-grade plug-and-play wiring harnesses using shielded cable, additional cables for 0 to 5 V signal input, and optional on-board enable/disable switch.
( 1 )
$429.00
AEM unsealed BMS Satellites modules are connected to their Master via a high-speed serial interface (isoSPI), allow additional units to be daisy chained together to support numerous battery pack configurations, allows for custom battery packs, and integration into a sealed module. AEM unsealed Satellite modules are intended for installations into sealed custom battery packs, and the low-profile 90-degree connector allows for ease of packaging and service when installed into a sealed battery pack.
Not Yet Reviewed
$249.95
On Sale
AEM Mini Master battery management systems are comprised of three components: 1. VCU 2. BMS-18 Mini Master 3. BMS-18 Satellite(s) The BMS is implemented as two different module types: the Mini Master and the Satellite. Each module is capable of measuring up to 18 cells and three temperatures (thermistors), but the Master also contains the CAN communication interface and J1772 charging specific connections needed for each battery pack. The VCU communicates with the BMS via the Mini Master module and all battery packs need at least one Mini Master unit. The Satellites expand the capability of the Master by an additional 18 cells and three thermistors per additional Satellite connected. The Satellite modules are connected to their Master via a high-speed serial interface (isoSPI) that allows additional units to be daisy chained together, adding as many Satellites as necessary for the battery pack configuration. The VCU is responsible for all BMS control logic. All setup and calibration items can be modified using the AEMCal user interface. Features: * Add-on expansion for VCU products, enabling the VCU's battery management features * Distributed BMS architecture allows for easy support of distributed battery packs * Interfaces with J1772 charge port to automatically power up vehicle when charge plug is connected * Up to 16 BMS18 Satellites can be connected to a single BMS18 Mini Master to support up to 1,200 V systems
Not Yet Reviewed
$284.95
$156.95
Edge EAS expandable EGT sensors allows you to monitor temperatures in different locations. Edge accessory systems are designed for expandability, and this permits you to connect multiple exhaust gas temperature sensors to ensure that the added power is not creating excessive heat. With Edge expandable EAS EGT sensors, you can compare readings in different areas to be even more precise with your temperature data.
( 11 )
$177.95
—
$187.95
On Sale
Bully Dog sensor docking stations offer an unparalleled glimpse into the comparative health of your vehicle. These accessories for the GT and Watch Dog product lines make it easy to install aftermarket automotive sensors onto your modern vehicle, and then display those specific values. They support a multitude of different measuring device types, including pressure (oil and/or boost), speed, and temperature sensors (exhaust, transmission and/or air intake). Bully Dog sensor docking stations are a superb, easy way for you to instantly check on the well-being of your vehicle.
( 1 )
$156.99
—
$171.99
$141.29
—
$152.99
FuelTech NanoPRO oxygen sensor conditioners have a new design, and with it they are able to condition and read five different models of wide band lambda O2 sensors: * BOSCH LSU 4.2 * BOSCH LSU 4.9 * BOSCH LSU 5.2 * NTK lab grade sensor * NTK wideband o2 sensor Way more than an O2 conditioner, NanoPRO has a 12-way connector with three wire groups. One of them has the connector for the O2 sensor, the second makes the CAN communication with PowerFT ECUs and the third is responsible for power and analog output. These 3-in-1 tools feature an extended wideband reading scale with advanced new hardware for fast and precise readings. Additional features and benefits: * Waterproof (IP67 certified with product harness connected) * 2 in. color display with resistive touch screen * Compatible with 5 different models of O2 sensors * Different fuels AFR or lambda display unit options-- reading range can reach values slightly lower or higher than 0.21 Lambda, depending on the manufacturing characteristics of the sensor: -- Lambda (0.21 - 9.99) -- AFR Methanol (1.35 - 64.6) -- AFR Gasoline (3.09 - 146.6) -- AFR Ethanol (1.89 – 89.9) * CAN communication with PowerFT ECUs: -- Second display gauge function that allows display valuable information like Oil Pressure, Fuel Pressure, Boost, RPM, Engine Temperature and much more coming from the FTCAN 2.0, with the possibility of configuring up to five custom screens -- Switch Panel function, touch screen buttons or switches via CAN bus to the PowerFT ECU * Three configurable O2 sensor heating modes: Normal, Fast, and Current Limited, as well as activated by engine rpm or temperature * Advanced heater diagnostics in the PowerFT ECU datalogger * 0 to 5 V analog output for connection with any data acquisition or programmable injection system. * Maximum power supply voltage: 20 V
Not Yet Reviewed
$339.00
Holley Terminator X MAX engine management systems let you take control of your domestic V8 engine. They give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X MAX features real-time fuel learn, high-impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. Also, Holley offers the X MAX systems with either or both drive-by-wire (DBW) throttle body control or transmission control. All kits come fully loaded with base maps for common domestic V8 engine combinations to get you out of the garage and onto the road or track fast. Order the model recommended for your vehicle application. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors (will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM, and for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables can be used for any custom tables * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most V8 engines, as well as tuning and gauge display functions
( 89 )
$1,699.95
—
$3,299.95
Holley Terminator X engine management systems let you take control of your domestic V8 engine. These kits give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X features real-time fuel learn, high impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. All systems come fully loaded with base maps for common engine combinations to get you out of the garage and onto the road or track fast. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors. (Will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables: 4 x 1D tables, 1 x 1D per gear table, 4 x 2D tables, 1 x 2D per gear table * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most domestic V8 engines, as well as tuning and gauge display functions (not available with every kit)
( 92 )
$1,349.95
—
$2,949.95
Haltech's Rebel LS ECU kits provide the most cost-effective, easy-to-install, start-up and drive aftermarket ECU experience. Designed for Gen 3 or 4 LS engines, the all-in-one kit concept simplifies your purchase decision, eliminating the need for costly additional accessory purchases. Each kit arrives with a Rebel ECU, main engine harness and adapter harnesses for throttle, injectors, T56 tranmission, (DBW -Gen 4) or (cable throttle and IAC – Gen 3) alternator, knock sensor, existing GM MAP, oil pressure sensors, along with a Bosch O2 and air temp sensor with weld bungs. Installation is a breeze, using a labeled and pre-terminated drop-in harness, which easily connects to existing factory LS sensors. Engine start-up is made easy through the Setup Wizard in the Haltech NSP software and the soon-to-be-released Haltech Connect app. Answer six questions – LS Engine type, cam, throttle body, MAP, injectors and coils with the Wizard prompting a throttle calibration and system check, ensuring an engine that will quickly start, idle and drive. Drivability is continually improved with Haltech's advanced self-learning while additional tuning for your N/A, turbocharged, supercharged or nitrous LS is achieved through Haltech's NSP software. Finally, the Rebel LS ECU kit is compatible with Haltech's plug-and-play CAN accessories, such as the iC-7 dash, keypads, PDM, EGT, wideband and flex-fuel sensors.
( 3 )
$1,495.00
Ford Performance Parts 2018-20 Gen 3 Coyote control packs are designed to run 2018-20 5.0L Mustang GT Coyote (Gen 3) automatic transmission engines with 10R80 Mustang GT 10-speed transmissions. They include a unique control pack harness, which replaces the stock body harness. These Ford Performance control packs were designed for performance enthusiasts who want the Gen 3 Coyote package in their own custom build. Includes: * PCM with Ford Performance calibration (requires return-type fuel system; not compatible with return-less-type) * Electronic throttle control accelerator pedal, eliminating throttle cable routing problems * OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis * Power distribution module * Mustang GT air box * Mustang GT air inlet tube * MAF sensor * Upper and lower radiator hoses * HEGO sensors
Not Yet Reviewed
$2,201.99
Ready for standalone engine management at a budget price? Take control of your GM Gen V LT1, L83, or L86 engine with a Holley Terminator X Max GM Gen V LT direct injection kit! They're available to fit early non-WT drive-by-wire engines, as well as late WT drive-by-wire engines. Terminator X and X Max features and benefits: * Plug-and-play GM Gen V LT engine control, including GDI and VVT support * Ideal for swapping late model GM Gen V LT engines into vintage vehicles * 3.5 in. hand-held gets your engine running in no time with a step-by-step calibration wizard * GM LS and LT drive-by wire throttle body control (Terminator X Max only) * GM 4L60 and 4L80 transmission control (Terminator X Max only) * Included engine harness plugs directly into the factory LT DI injector sub harness * OEM Injectors supported, with part numbers provided in the handheld wizard or software * Genuine Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal – Cam Signal – VVT Status – Pump Control – and DI Injectors. This allows you to identify any critical engine issues at a glance * Built-in 1 bar MAP sensor, vacuum hose adapters included (1/8th, 1/4 and 3/16ths); or for Boosted applications, you can disable the internal MAP sensor, and utilize an external LT MAP sensor. The harness comes with the connector terminated, making the installation a snap * 4 inputs: 12 V, Ground, 5 V, and Frequency—for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (Fuel and Oil Pressure inputs are pre-terminated) * 4 Outputs: -- Ground -- PWM – for accessories such as fans, boost control, nitrous control, IAC kit, and more -- Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties -- Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR * Integrated data logging to the 3.5 in. hand-held SD card * Free EFI tuning software for complete control of your Terminator X powerplant Terminator X Max ECU Connections: * J1A - Main Harness Connector: This connector is primarily an "Input" connector. It contains all the sensor inputs and wide band oxygen sensor control. * J1B - Main Harness Connector: The second connector is the "J1B" connector (26 pin). This connector is the "output" connector. It has eight injector outputs and outputs for other devices. * MAP Sensor: Used on N/A applications, connect directly to full manifold vacuum port on the intake manifold. * Main Power: Connects to the Main Power Harness; these two wires MUST be wired directly to the battery terminals. * J3: Connection point for the drive-by-wire harness. * J4: Connection point for the transmission harness.
Not Yet Reviewed
$3,049.95
—
$3,549.95
Holley Dominator EFI vehicle management systems are intended for all engine applications, from street to high-end racing. They have nearly unlimited capabilities to control any power adder, input, or output that you can throw at them. Features include: * 12 sequentially driven 8:2 peak and hold injector drivers capable of driving up to 24 low or high-impedance injectors * 12-channel distributorless ignition outputs capable of directly driving smart ignition coils or Holley DIS coils * Plug-and-play control of factory GM 24x and 58x LSX engines * Integrated electronic transmission control--currently can control GM 4L60E and 4L80E * Integrated dual channel wideband oxygen sensor controls, work with NTK or Bosch sensors * Integrated drive by wire throttle body control, can control two drive by wire throttle bodies * 4-stage progressive nitrous oxide controller * Turbo boost control * Integrated water/methanol injection control * Integrated data acquisition and control allowed with massive amount of programmable inputs and outputs * Internal data logging standard with a huge 2 GB of memory * Self-tuning fuel table strategy greatly simplifies tuning process * Store and change between four calibrations * Individual cylinder fuel and spark control allows you to unlock your engine's potential
( 6 )
$2,349.95
—
$3,399.95
Looking to add a Ford Performance Parts crate engine to your custom built vehicle? Take the complexity and mystery out of wiring your new build with Ford Performance Parts crate engine control packs! Features include: * Unique controls pack harnesses to replace stock body harnesses; designed for custom-built vehicles * OBD-II diagnostic ports to assist in vehicle calibration uploads and diagnosis of problems * PCMs with Ford Performance Parts performance calibration (custom calibration required on some engines and for aftermarket intake systems) * Electronic throttle control accelerator pedals, eliminating throttle cable routing problems * Power distribution modules * Requires return-type fuel system, will not work with returnless fuel system
( 1 )
$1,949.99
FiTech Ultimate TPI standalone ECUs bring an old GM TPI-controlled engine (L98, LB9) into modern times. These standalone EFI kits plug into all existing sensors on a GM TPI engine and provides complete control of the engine. From timing control to self-learning fueling, FiTech Ultimate TPI standalone ECUs deliver new life into the GM TPI engine.
( 9 )
$847.00
—
$1,060.00
Ford Performance Parts 7.3L gas engine control packs include components and harness to install a 2020 to present Super Duty 7.3L gas engine with a 10R140 automatic transmission in a vehicle. The unique control pack harnesses replace the production body harness designed for custom vehicle builds. These kits require use of a conventional return-type fuel system. Note: Installation of PCM in a production vehicle will result in a "no start" situation.
Not Yet Reviewed
$2,285.99
—
$2,396.99
Holley HP EFI ECU and harness kits allow you to manage automotive functions—like the fuel and ignition of your engine, along with controlling nitrous, boost, or water/methanol. Select the model with options needed for your vehicle application. (Note: some models are engine-specific.) Features and notes: * Eight sequentially driven 8:2 peak and hold injector drivers capable of driving up to 16 low or high-impedance injectors are standard * 8-channel distributorless ignition (DIS) outputs capable of directly driving "smart" ignition coils or Holley DIS coils * Integrated, single-channel wideband oxygen sensor control. Works with NTK or Bosch sensors. More channels can be added via CAN bus. * Internal data-logging is standard, with a huge 2GB of memory * 4-stage progressive nitrous control * Turbo boost control * Integrated water/methanol injection control * Self-tuning fuel table strategy greatly simplifies tuning process * Individual cylinder fuel and spark control allow you to unlock your engine's potential * Compatible with 4, 6, and 8-cylinder engines * Unique lbs./hr.-based fueling strategy greatly simplifies tuning * Advanced idle, closed loop, and enrichment strategies allow for very stable operation * Fully potted and can be mounted in the engine compartment or interior * Sealed automotive and marine-grade connectors * Allows for use of common OEM sensors, as well as customer sensor calibration input * Ignition plug-and-play with GM 24x and 58x LSx engines, GM HEI, Ford TFI, magnetic, and hall effect trigger, and other ignition systems * 1-5 bar MAP sensor capability * 2-channel knock control sensor inputs for both one and 2-wire knock sensors * Dedicated fuel and oil pressure inputs * Control both stepper and PWM idle air control (IAC) motors * Speed density, Alpha-N, or combination fueling strategies * Four programmable high or low pulse width modulated (PWM) outputs and four fully configurable inputs can be configured for use * Lean or rich safety cutoff
( 25 )
$1,999.95
—
$3,849.95
For cars with an identity crisis (they don't know if they're a street car or a race car), XFI Sportsman electronic fuel injection systems fill a hole in the middle of the FAST lineup. They're designed to satisfy the enthusiast who does spend some time racing, but also spends time cruising. These EFI engine control systems will serve to simplify the tuning process and give you the capability to control the engine with greater control and precision than currently exists. When we say simple, we mean really simple--installation is a snap, and if you've ever worked with tuning software in the past, XFI's C-Com software will be familiar to you. If not, then you can use the self-tuning option and be off to the races as you learn the capabilities of your new system. The FAST systems ship with an ECU, wiring harnesses, wideband oxygen sensor, and electronic fuel pressure kit.
( 5 )
$1,712.95
—
$1,931.95
Chevrolet Performance LT4 engine controller kits are fully integrated, stand-alone kits designed to run LT4 Series crate engines. Each kit features: * Engine Control Module (ECM—unique to LT4 automatic transmission/T56 manual transmission or 8-speed automatic transmissions) * LT4 engine harness—unique to each kit * Mass airflow sensor * Mass airflow sensor bracket * MAF bolt/screw/washer * Accelerator pedal * Oxygen sensors and mounting bosses * Fuel line pressure sensor * Fuel pump power module * Bolt/screw—M8 x 1.25 x 25 * Bolt/screw—M8 x 1.5 x 30 * Emblem * I-sheet (instruction sheet)
Not Yet Reviewed
$3,003.40
—
$3,961.31
Edge EAS Street Diesel kits give users the ability to monitor EGTs, boost pressure and fuel pressure—exactly what most diesel owners want to see. These kits are designed for those truck owners who have upgraded their rigs with larger turbos, performance lift pumps, and maybe even injectors, where the stock sensors just aren't enough anymore. The kits are ideal for hot street trucks, daily drivers, and towing applications. The EGT probe can easily be installed in the exhaust manifold for the most accurate cylinder temps. The EAS 0-100 psi sensor is the perfect sensor for an aftermarket turbo that can build more boost than the stock MAP sensor can read. The second 0-100 psi sensor can be easily installed on an aftermarket lift pump or anywhere in the low-pressure fuel side to monitor lift pump pressure, ensuring your injection system is getting all the fuel it needs. All-new Street Diesel kits save money over buying the three sensors separately and offer another great solution for those with aftermarket performance accessories on their diesel. Product details: * 1 EAS Starter Kit * 1 EAS EGT Probe * 2 EAS 0-100psi Pressure Sensors * 1 EAS Universal 5 V Harness Kit (accepts two pressure sensor kits)
Not Yet Reviewed
$399.95
On Sale
Now you can monitor your exhaust gas temperature through your SCT device instrumentation system! These SCT exhaust gas temperature sensor kits allow you to monitor your exhaust gas temperature so you can tune for maximum performance. Product features: * Plug and play with SCT's devices * Works with SCT device warning lights * Easy installation * Monitor your vehicle's EGT temps
( 3 )
$166.99
$151.99
BluePrint Engines strive to make your LS swap as simple as possible. To that end, BluePrint Engines LS engine compatible controller kits contain all the components and proper calibration to get your engine installed in your muscle car or truck, and have you tearing up the streets in no time. BluePrint takes a complete LS controller package, and specially calibrates the ECU to the optimum tuning required. They also leave the ECU unlocked so your dyno shop can further refine your tune after your swap is complete into your vehicle. Controller kit contents: * ECU * Engine harness * Mass airflow meter and mounting boss * Accelerator pedal assembly * Oxygen sensors and bungs
Not Yet Reviewed
$2,299.00
Chevrolet Performance controllers are uniquely calibrated for installation in older vehicles—unlike the controllers from regular-production vehicles. That means many features required for late-model production vehicles are "turned off" because they are not required in older cars and trucks. This helps to prevent the unnecessary triggering of diagnostic trouble codes that could possibly affect performance or require additional calibration adjustments. These engine controller kits are designed exclusively for Chevrolet LS427 570 horsepower wet sump LS7 crate engines. If you have a late model Chevy, you'll want this kit! The kit includes: * Engine controller * Wiring harness * Mass airflow meter * Throttle pedal assembly * Oxygen sensors
Not Yet Reviewed
$1,889.51
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
