Availability
Showing In Stock Items. Show All 211 Items.
Ford Performance presents the next generation 5.0L power all-in-one complete powertrain kit! The crew at Ford Performance spec'd out these kits to simplify the swap of the newest, most innovative 5.0L Coyote engine into just about any Ford vehicle. The Coyote power module teams the Mustang GT 460 hp 5.0L Coyote V8 with a state-of-the-art 10-speed automatic transmission, along with all the electronics and hardware to finish the installation. The engine features advances like direct and port fuel injection, twin independent variable camshaft timing, along with a lightweight plasma transferred wire arc spray aluminum engine block. The Coyote power module simplifies both the shopping and build experience by kitting up the right parts that are matched to deliver potent performance with civilized drivability. The engine control pack is truly plug-and-play to simplify the conversion to a modern electronically fuel injected V8 high performance engine. Build the Coyote project of your dreams with high-quality aftermarket parts by Ford Performance!
Not Yet Reviewed
$19,555.99
Tweak the software in your 2.0L EcoBoost engine and wake up your Focus ST. Ford Performance Parts 2013-18 Ford Focus ST calibration and spark plug kits will give you additional power with a more natural engine sound. Kits include a Ford Performance Parts cold spark plug set and the ProCal3 hand-held tuner (requires a laptop and internet access for calibration). Additional notes: * Maximum of 90 lbs.-ft. torque increase at 2800 rpm on 93 octane fuel * Significant torque increase up to 4200 rpm * Revised sound symposer software and calibration * Requires premium (91 octane or higher) fuel only * Spark plugs gapped to 0.028 in. (0.71mm) * Powertrain calibrations are developed and supported for U.S. and Canadian vehicles only * Calibration is 50-states emissions legal * Eligible for limited warranty when installed by a Ford or Lincoln dealer or ASE certified technician
( 6 )
$362.99
Haltech's Rebel LS ECU kits provide the most cost-effective, easy-to-install, start-up and drive aftermarket ECU experience. Designed for Gen 3 or 4 LS engines, the all-in-one kit concept simplifies your purchase decision, eliminating the need for costly additional accessory purchases. Each kit arrives with a Rebel ECU, main engine harness and adapter harnesses for throttle, injectors, T56 tranmission, (DBW -Gen 4) or (cable throttle and IAC – Gen 3) alternator, knock sensor, existing GM MAP, oil pressure sensors, along with a Bosch O2 and air temp sensor with weld bungs. Installation is a breeze, using a labeled and pre-terminated drop-in harness, which easily connects to existing factory LS sensors. Engine start-up is made easy through the Setup Wizard in the Haltech NSP software and the soon-to-be-released Haltech Connect app. Answer six questions – LS Engine type, cam, throttle body, MAP, injectors and coils with the Wizard prompting a throttle calibration and system check, ensuring an engine that will quickly start, idle and drive. Drivability is continually improved with Haltech's advanced self-learning while additional tuning for your N/A, turbocharged, supercharged or nitrous LS is achieved through Haltech's NSP software. Finally, the Rebel LS ECU kit is compatible with Haltech's plug-and-play CAN accessories, such as the iC-7 dash, keypads, PDM, EGT, wideband and flex-fuel sensors.
( 3 )
$1,495.00
Chevrolet Performance 480 hp LS3 engine controller kits include all of the components required to run your Chevrolet Performance Parts crate engine. They include an engine harness, a mass airflow meter with a mounting boss, oxygen sensors (2) with weld-in bungs (2), an accelerator pedal assembly, and a detailed instruction sheet. The kits have been specially preprogrammed for retrofitting a late model 6.2L LS3 Chevrolet engine in your street rod, hot rod, or muscle car.
( 1 )
$2,167.43
These Chevrolet Performance Parts LS 376/525 hp engine controller kits are designed for controlling your GM LS 525 hp engine. They include a new controller, engine harness, mass airflow meter, mass airflow meter mounting boss, accelerator pedal assembly, two oxygen sensors, two oxygen sensor mounting bosses, and an instruction manual.
( 1 )
$2,225.39
Holley HP EFI ECU and harness kits allow you to manage automotive functions—like the fuel and ignition of your engine, along with controlling nitrous, boost, or water/methanol. Select the model with options needed for your vehicle application. (Note: some models are engine-specific.) Features and notes: * Eight sequentially driven 8:2 peak and hold injector drivers capable of driving up to 16 low or high-impedance injectors are standard * 8-channel distributorless ignition (DIS) outputs capable of directly driving "smart" ignition coils or Holley DIS coils * Integrated, single-channel wideband oxygen sensor control. Works with NTK or Bosch sensors. More channels can be added via CAN bus. * Internal data-logging is standard, with a huge 2GB of memory * 4-stage progressive nitrous control * Turbo boost control * Integrated water/methanol injection control * Self-tuning fuel table strategy greatly simplifies tuning process * Individual cylinder fuel and spark control allow you to unlock your engine's potential * Compatible with 4, 6, and 8-cylinder engines * Unique lbs./hr.-based fueling strategy greatly simplifies tuning * Advanced idle, closed loop, and enrichment strategies allow for very stable operation * Fully potted and can be mounted in the engine compartment or interior * Sealed automotive and marine-grade connectors * Allows for use of common OEM sensors, as well as customer sensor calibration input * Ignition plug-and-play with GM 24x and 58x LSx engines, GM HEI, Ford TFI, magnetic, and hall effect trigger, and other ignition systems * 1-5 bar MAP sensor capability * 2-channel knock control sensor inputs for both one and 2-wire knock sensors * Dedicated fuel and oil pressure inputs * Control both stepper and PWM idle air control (IAC) motors * Speed density, Alpha-N, or combination fueling strategies * Four programmable high or low pulse width modulated (PWM) outputs and four fully configurable inputs can be configured for use * Lean or rich safety cutoff
( 25 )
$1,999.95
—
$3,849.95
Ready for standalone engine management at a budget price? Take control of your GM Gen V LT1, L83, or L86 engine with a Holley Terminator X Max GM Gen V LT direct injection kit! They're available to fit early non-WT drive-by-wire engines, as well as late WT drive-by-wire engines. Terminator X and X Max features and benefits: * Plug-and-play GM Gen V LT engine control, including GDI and VVT support * Ideal for swapping late model GM Gen V LT engines into vintage vehicles * 3.5 in. hand-held gets your engine running in no time with a step-by-step calibration wizard * GM LS and LT drive-by wire throttle body control (Terminator X Max only) * GM 4L60 and 4L80 transmission control (Terminator X Max only) * Included engine harness plugs directly into the factory LT DI injector sub harness * OEM Injectors supported, with part numbers provided in the handheld wizard or software * Genuine Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal – Cam Signal – VVT Status – Pump Control – and DI Injectors. This allows you to identify any critical engine issues at a glance * Built-in 1 bar MAP sensor, vacuum hose adapters included (1/8th, 1/4 and 3/16ths); or for Boosted applications, you can disable the internal MAP sensor, and utilize an external LT MAP sensor. The harness comes with the connector terminated, making the installation a snap * 4 inputs: 12 V, Ground, 5 V, and Frequency—for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (Fuel and Oil Pressure inputs are pre-terminated) * 4 Outputs: -- Ground -- PWM – for accessories such as fans, boost control, nitrous control, IAC kit, and more -- Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties -- Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR * Integrated data logging to the 3.5 in. hand-held SD card * Free EFI tuning software for complete control of your Terminator X powerplant Terminator X Max ECU Connections: * J1A - Main Harness Connector: This connector is primarily an "Input" connector. It contains all the sensor inputs and wide band oxygen sensor control. * J1B - Main Harness Connector: The second connector is the "J1B" connector (26 pin). This connector is the "output" connector. It has eight injector outputs and outputs for other devices. * MAP Sensor: Used on N/A applications, connect directly to full manifold vacuum port on the intake manifold. * Main Power: Connects to the Main Power Harness; these two wires MUST be wired directly to the battery terminals. * J3: Connection point for the drive-by-wire harness. * J4: Connection point for the transmission harness.
Not Yet Reviewed
$3,049.95
—
$3,549.95
HP Tuners ECM Upgrade Kits will give do-it-yourself enthusiasts and professional tuners a convenient option to perform the ECM upgrade on their 2017+ Chevy Silverado/GMC Sierra 6.6L Duramax in their own garage/shop. The best part? There's no need to remove the ECM from the truck. This means there's no risk of breaking tabs during the removal or reinstallation process, and the kit doesn't require any reprogramming or relearns. From start to finish, you can upgrade your E41 ECM in roughly 20 minutes—all you need is this upgrade kit, your MPVI2+ with Pro Feature Set or MPVI3 device with its supplied USB A to C cable, and a VCM Suite-compliant computer with the latest version of VCM Suite BETA. Once the ECM is upgraded, you'll experience the industry's most comprehensive diagnostics and tuning package using VCM Suite with full scan, data log, read, edit, and write capabilities. Plus, you'll experience the quickest write times in the industry in approximately 6 minutes! Product features and benefits: * No IMMO relearn * No crank relearn * No need to perform "Replace ECM" function
Not Yet Reviewed
$199.99
On Sale
The Holley EFI CAN Input/Output Module kit can be added to Holley EFI HP, Dominator, Terminator X and Terminator X Max EFI installation. This CAN module will add eight inputs and eight outputs to the system, which can be used to control additional accessories or provide critical sensor inputs. This module is perfect for anyone wanting to enhance the capabilities of their current ECU, yet have already tapped out their ECU's Input/Output channels. Product features: * Quickly expand your HP/Terminator X or even Dominator ECU's Input/Output control with 8 additional inputs and outputs * This module is perfect for anyone wanting their Holley EFI ECU to control more functions or monitor more data channels * HP and Terminator X EFI installations with only 4 inputs and 4 outputs can now add more functionality to their EFI system * The 554-165 kits contain a pre-terminated CAN harness, allowing you to quickly install the Holley EFI CAN Module to any existing Holley EFI installation * Pre-terminated flying leads makes installing new wires a breeze * Inputs can be used for things such as: - Switch 12 V toggle switches; can be configured for external mechanical relays, or setup as digital switches via a Holley EFI dash - Ground input for brake pedal switch - 5 V analog inputs for sensors like fuel pressure, oil pressure, or nitrous bottle pressure - Thermistor inputs for coolant temperature sensors * Outputs can be used for things such as: - Switch Low (ground); for relay control or activation - Switch Low PWM (ground); PWM fan control, PWM fuel pump control, or other PWM-controlled devices * Adjustable broadcast rate for each channel: from 0-100hz
( 3 )
$482.95
Add GM 6L80/90E transmission control to any existing vehicle utilizing a Terminator X Max ECU. A departure from traditional Holley EFI transmission control, the Terminator X Max ECU allows the ability to use 2007+ GM 6L80E and 6L90E transmissions by communicating via CAN with the internal TCM (Transmission Control Module). The supplied Holley EFI OBDII transmission tuning hand-held is used to adjust shift points, tire size and gear ratio. Terminator X V3 software provides the ability to dial in torque management to optimize the desired shifting characteristics when using a 6L80/90E transmission. The software also enables you to control the secondary shift mode within the transmission TCM and allows use of tap Up/Down shifting. Within Terminator X V3 PC Software: --- Virtual Torque Management Tables --- Virtual TPS Tables to dial in shift characteristics regardless of engine --- DBW and Timing torque reduction tables to create smooth shifts Within the Holley EFI OBDII Transmission Tuning Hand-held: --- Ability to read and clear TCM fault codes --- Ability to raise and lower shift points by MPH or RPM --- Support for Tap Up/Tap Down & Transmission's Secondary Shift Mode If you currently have a Terminator X ECU, upgrading to a Terminator X Max ECU can be easily done by plugging your main harness into the Max ECU and re uploading your existing calibration. Holley Terminator X MAX GM 6L80/90 transmission kit features: * Included TCM hand-held tuner with integrated wizard is required for setup in conjunction with the Terminator X 3.5 in. hand-held. Terminator X V3 software unlocks optional tuning parameters. * Plug-and-play with any engine controlled by a Terminator X Max ECU * Supports: Shift Mode - Tap Up / Tap Down, and torque management * Four loose wires: --- Power (Red): Supplies power to the transmission solenoids. This should be connected directly to the battery, or a constant battery source capable of supplying 5 amps --- Ground (Black): Connect to a good chassis/engine ground source --- Brake Switch (Light Blue/White): Wired to the brake light switch. This must be installed to a +12 V source (as most brake light switches are) --- Park/Neutral Safety (Yellow): Circuit for starter solenoid. When the transmission is in Park or Neutral, this yellow wire will be grounded (-). When the transmission is in gear this circuit will be open.
Not Yet Reviewed
$573.95
The 2019-2022 (22.5+ refresh not supported at this time) GM gas trucks have been locked down since their introduction. Owners of these trucks have been waiting patiently for a tuning solution, and DiabloSport has delivered in a big way! The new 8225-R kit includes an industry-leading inTune 3 handheld tuner, along with the locksmith device and harnesses required to unlock both the ECM and TCM in your truck. Once unlocked, the inTune 3 offers up tunes for 87, 91 and 93 octane fuels, as well as two transmission tunes to choose from. Beyond the preloaded tunes, DiabloSport offers a host of user adjustable parameters, like throttle response, speed limit, tire size, and of course, DFM disable! They've even added some new features for drivers of these newer trucks, like the ability to recall your last mode setting, or to retain your auto-start-stop setting. Get power you can feel—with DiabloSport! DiabloSport inTune 3 GM E90/T93 unlock kit features: * ECM and TCM unlock included * Unlock and tune at home * Preloaded tunes for multiple octane levels * Support for 5.3L and 6.2L V8 applications with 6, 8 or 10-speed transmissions * Disable Dynamic Fuel Management for full time V8 operation * Throttle Boost setting for adjustable throttle feel * Adjust speedometer for larger tires (26 – 38 in.) * Calibrate speedometer for gear change (3.42-5.13) * Remove speed limiter for increased top speed * Adjust engine rev limiter for increased RPM range (+/- 400 rpm) * Adjust engine idle speed in Park/Neutral and Drive * New 'Keep Auto Stop Start Setting' allows you to disable the system using the button on the dash—and it stays that way! * New 'Keep Drive Mode Setting' allows you to select a drive mode and it will remember that mode next time you start the truck!
( 1 )
$849.95
Chevrolet Performance Parts LS controller kits have everything that you need to properly tune your Chevrolet Performance Parts crate engine. Kits include: * ECU * Engine wiring harness * Mass airflow meter * Mass airflow meter mounting boss * Accelerator pedal assembly * Two oxygen sensors with mounting bosses * Detailed instruction sheet
( 1 )
$2,167.43
FAST EZ-EFI 2.0 Multi-Port Retro-Fit kits allow owners of existing factory or aftermarket multi-port fuel injected applications and intake manifolds to experience the benefits of an EZ-EFI 2.0 system with no limit on horsepower—because the systems are based on each customer's supplied injectors. The next generation of the revolutionary self-tuning EZ-EFI has been upgraded with more features than ever before. Yet it maintains ease of use that doesn't require a laptop or tuning experience. As with the original EZ-EFI, simply hook up the system, answer the Setup Wizard questions on the hand-held, and EZ-EFI 2.0 tunes itself as you drive. The new high-quality wiring harness (with a sleek mesh-type loom) uses commonly available late model OEM sensors for accuracy and durability. The EZ-EFI 2.0 has an updated hand-held, as well, featuring the industry's first color touch screen. Self-powered through the ECU rather than requiring an outside power source, it shares the same mounting points as the Garmin Nuvi GPS—meaning there are nearly limitless mounting options (suction cup mount is included with all kits). Serving as the Setup Wizard initially, it then becomes an electronic gauge screen. The hand-held has various advanced features, including screen hide/sleep function, expanded diagnostics and data screens, plus intuitive navigation. Electronic fuel pressure measurement is standard on all kits—and all kits work with wet nitrous systems, providing built-in nitrous timing retard and special nitrous AFR targeting. EZ-Ignition features an EZ-Solution option, meaning that it is plug-and-play with FAST Dual-Sync distributors for electronic timing control, or can be used with an EFI distributor of your choice and a FAST crank trigger. Or the system can be used to control fuel only and be used with a standard carb-type distributor where timing is set manually. Experience the advantage of fuel injection without the headaches; order a FAST EZ-EFI 2.0 Multi-Port Retro-Fit kit.
( 10 )
$1,589.95
Edge's EZ+Insight CTS3 L5P Duramax kits provide "EZ" power for your Duramax diesel paired with their Insight CTS3, giving you more control with added features, like the ability to read and clear trouble codes, perform a manual DPF Regeneration cycle, and of course, monitor everything going on under the hood. Get peace of mind with the data Insight provides real-time through a state-of-the-art color touch screen. Watch live data, like EGTs, boost, rail pressure, soot levels, DPF status, and even distance since your last regen. Edge EZ module makes a massive improvement in drivability without sacrificing longevity or the reliability of your emissions equipment. Their intuitive smartphone app offers on-the-fly tuning adjustments over five specific calibrations, and to further enhance your driving experience, each of the five power levels can be adjusted to run one of seven throttle pedal settings giving you the control over throttle feel, eliminating pedal lag. For extra value and savings, purchase an Edge EZ + Insight kit to give your L5P exactly what it needs.
Not Yet Reviewed
$999.95
The 2019-2022 (22.5+ refresh not supported at this time) GM gas trucks have been locked down since their introduction. Owners of these trucks have been waiting patiently for a tuning solution, and DiabloSport has delivered in a big way! The new 9225-R kit includes an industry-leading Trinity 2 on-dash tuner, along with the locksmith device and harnesses required to unlock both the ECM and TCM in your truck. Once unlocked, the Trinity 2 offers up tunes for 87, 91 and 93 octane fuels, as well as two transmission tunes to choose from. Beyond the preloaded tunes, DiabloSport offers a host of user adjustable parameters, like throttle response, speed limit, tire size, and of course, DFM disable! They've even added some new features for drivers of these newer trucks, like the ability to recall your last mode setting, or to retain your auto-start-stop setting. And it doesn't stop there with T2. The full color, 5 in. touch screen allows you to keep an eye on all your vital engine data. The on-screen gauges deliver all the info you want to see, in real time. Of course, it can also record data for playback on our DV2 software for further analyzation. T2 also enables you to set up virtual alerts, and supports the Expandable Accessory System (EAS) for adding and logging additional external sensors. The device is internet updateable, either through DiabloSport's Update Agent software or through its built in WiFi. Get power you can feel—with DiabloSport! DiabloSport Trinity 2 GM E90/T93 unlock kit features: * ECM and TCM unlock included * Unlock and tune at home * Preloaded tunes for multiple octane levels * Full-color 5 in. touch screen * Support for 5.3L and 6.2L V8 applications with 6, 8 or 10-speed transmissions * Disable Dynamic Fuel Management for full time V8 operation * Throttle Boost setting for adjustable throttle feel * Adjust speedometer for larger tires (26 – 38 in.) * Calibrate speedometer for gear change (3.42-5.13) * Remove speed limiter for increased top speed * Adjust engine rev limiter for increased RPM range (+/- 400 rpm) * Adjust engine idle speed in Park/Neutral and Drive * New 'Keep Auto Stop Start Setting' allows you to disable the system using the button on the dash—and it stays that way! * New 'Keep Drive Mode Setting' allows you to select a drive mode and it will remember that mode next time you start the truck! * Customizable gauge layouts and background images * Supports DiabloSport's Expandable Accessory System * Includes windshield mount
Not Yet Reviewed
$949.95
HalTech offers a variety of data acquisition components and accessories to facilitate engine management and automotive performance. These replacement idle air control kits include a billet 2-port housing with 2-screw style motor. They're built to fit and function like the originals. Matching plugs and pins are included.
Not Yet Reviewed
$185.00
Edge EAS Street Diesel kits give users the ability to monitor EGTs, boost pressure and fuel pressure—exactly what most diesel owners want to see. These kits are designed for those truck owners who have upgraded their rigs with larger turbos, performance lift pumps, and maybe even injectors, where the stock sensors just aren't enough anymore. The kits are ideal for hot street trucks, daily drivers, and towing applications. The EGT probe can easily be installed in the exhaust manifold for the most accurate cylinder temps. The EAS 0-100 psi sensor is the perfect sensor for an aftermarket turbo that can build more boost than the stock MAP sensor can read. The second 0-100 psi sensor can be easily installed on an aftermarket lift pump or anywhere in the low-pressure fuel side to monitor lift pump pressure, ensuring your injection system is getting all the fuel it needs. All-new Street Diesel kits save money over buying the three sensors separately and offer another great solution for those with aftermarket performance accessories on their diesel. Product details: * 1 EAS Starter Kit * 1 EAS EGT Probe * 2 EAS 0-100psi Pressure Sensors * 1 EAS Universal 5 V Harness Kit (accepts two pressure sensor kits)
Not Yet Reviewed
$399.95
Chevrolet Performance LT4 engine controller kits are fully integrated, stand-alone kits designed to run LT4 Series crate engines. Each kit features: * Engine Control Module (ECM—unique to LT4 automatic transmission/T56 manual transmission or 8-speed automatic transmissions) * LT4 engine harness—unique to each kit * Mass airflow sensor * Mass airflow sensor bracket * MAF bolt/screw/washer * Accelerator pedal * Oxygen sensors and mounting bosses * Fuel line pressure sensor * Fuel pump power module * Bolt/screw—M8 x 1.25 x 25 * Bolt/screw—M8 x 1.5 x 30 * Emblem * I-sheet (instruction sheet)
Not Yet Reviewed
$3,003.40
—
$3,961.31
HalTech Nexus R3 with universal wire-in harness kits are ideal for dedicated race cars, engine swaps and custom wiring jobs. The harness has a set of VCU connectors at one end and unterminated wires at the other. All the wires at the unterminated end are color-coded and clearly labeled. Connect your HalTech VCU to the terminated end and follow your wiring diagram for all the engine connections. Load your base map and you're ready to go! * Color-coded and labeled wires that match the detailed wiring diagram for a confusion free construction process. * The wiring diagram is accompanied by the full VCU manual and software located on the USB key provided with the VCU, or downloadable from the HalTech website. VCU OVERVIEW: * Nexus R3 combines the functionality of a power distribution module, a data logger, a wideband controller, and a state-of-the art engine management system in one powerful device HalTech calls a VCU (Vehicle Control Unit) * 4 x 25A (continuous) push-pull PWM capable (5 kHz) outputs (for power to injectors / coils, transbrake, thermofan, fuel pump) * 8 x peak/hold injector drivers (can be used as low side drive outputs) * 8 x low current ignition outputs (can be used as low side drive outputs) * 6 x low side drive outputs, PWM capable (DPOs) * 6 x push-pull /H-bridge outputs (8A, PWM capable), e.g. for electronic throttle * 11 x 0-5 V analog inputs with redundancy for electronic throttle and switchable 5 V pullup * Trigger and home inputs with differential inputs, adjustable thresholds and glitch filters * 6 x synchronous pulsed inputs, zero crossing or adjustable thresholds - cam sensor inputs, frequency inputs or 0-5 V analog inputs * 1 x on-board wideband controller, supporting NTK and LSU4.9 * 1 x on-board 4 bar MAP sensor * 2 x CAN ports with switchable termination * Suits: Engines with up to 8 cylinders or up to 4 rotors. Racing applications where advanced race features, data logging and power management control are required. * Includes: Nexus R3 VCU, SurLok connectors (red and black), WiFi antenna, mounting bolts, USB-C cable, USB-C dust cap, USB drive with NSP software. Nexus R3 universal wire-in engine harness.
Not Yet Reviewed
$2,799.00
Chevrolet Performance controllers are uniquely calibrated for installation in older vehicles—unlike the controllers from regular-production vehicles. That means many features required for late-model production vehicles are "turned off" because they are not required in older cars and trucks. This helps to prevent the unnecessary triggering of diagnostic trouble codes that could possibly affect performance or require additional calibration adjustments. These engine controller kits are designed exclusively for Chevrolet LS427 570 horsepower wet sump LS7 crate engines. If you have a late model Chevy, you'll want this kit! The kit includes: * Engine controller * Wiring harness * Mass airflow meter * Throttle pedal assembly * Oxygen sensors
Not Yet Reviewed
$1,889.51
BluePrint Engines strive to make your LS swap as simple as possible. To that end, BluePrint Engines LS engine compatible controller kits contain all the components and proper calibration to get your engine installed in your muscle car or truck, and have you tearing up the streets in no time. BluePrint takes a complete LS controller package, and specially calibrates the ECU to the optimum tuning required. They also leave the ECU unlocked so your dyno shop can further refine your tune after your swap is complete into your vehicle. Controller kit contents: * ECU * Engine harness * Mass airflow meter and mounting boss * Accelerator pedal assembly * Oxygen sensors and bungs
Not Yet Reviewed
$2,299.00
Edge EAS accessory starter kits allow you to connect multiple accessories daisy chain-style to your Evolution CS or CTS programmers. A variety of computer programmer accessories are available, such as a power supply or cable. EAS kits are expandable at any time.
Not Yet Reviewed
$73.05
Make something old, new again with this Edge upgrade kit that will convert a CS2 and CTS2 Juice with Attitude to the latest CTS3 display. This kit will include the new CTS3 monitor, a new window mount and update cable. This will allow total integration of the state-of-the-art CTS3 monitor for your currently installed Juice with Attitude system. The CTS3 monitor offers faster processing speeds, quicker load times, a more intuitive state-of-the-art swipe technology, crisper display, and sleeker look. This kit works for Dodge/Ram Cummins and GM Duramax applications only, and will not support the Ford Power Stroke platforms. For current owners running an Edge backup camera with their CTS2 Juice with Attitude system, a 98107 CTS3 camera adapter kit will be required to work with the CTS2 display. (NOTE: This upgrade kit does NOT include the required Juice modules, sensors, or wiring harnesses associated with it. This part number cannot be run as a standalone monitor and MUST be used in conjunction with a previously installed Juice CS2 or CTS2 system.)
Not Yet Reviewed
$499.95
Chevrolet Performance LS7 engine controller kits are calibrated to run your 2007-2013 LS7 crate engines. These module and harness kits are designed for easy plug-and-play installation, and are inclusive for all components needed to get your LS-family engine running. These Chevy Performance kits include: * Controller * Engine harness * Mass airflow meter and mounting boss * Accelerator pedal assembly * 2 oxygen sensors and bosses * Instruction sheet
Not Yet Reviewed
$2,189.98
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
