Computers, Chips & Programmers Ignitions & Electrical

Holley Terminator X Max GM Gen V LT Direct Injection Kits

Ready for standalone engine management at a budget price? Take control of your GM Gen V LT1, L83, or L86 engine with a Holley Terminator X Max GM Gen V LT direct injection kit! They're available to fit early non-WT drive-by-wire engines, as well as late WT drive-by-wire engines. Terminator X and X Max features and benefits: * Plug-and-play GM Gen V LT engine control, including GDI and VVT support * Ideal for swapping late model GM Gen V LT engines into vintage vehicles * 3.5 in. hand-held gets your engine running in no time with a step-by-step calibration wizard * GM LS and LT drive-by wire throttle body control (Terminator X Max only) * GM 4L60 and 4L80 transmission control (Terminator X Max only) * Included engine harness plugs directly into the factory LT DI injector sub harness * OEM Injectors supported, with part numbers provided in the handheld wizard or software * Genuine Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal – Cam Signal – VVT Status – Pump Control – and DI Injectors. This allows you to identify any critical engine issues at a glance * Built-in 1 bar MAP sensor, vacuum hose adapters included (1/8th, 1/4 and 3/16ths); or for Boosted applications, you can disable the internal MAP sensor, and utilize an external LT MAP sensor. The harness comes with the connector terminated, making the installation a snap * 4 inputs: 12 V, Ground, 5 V, and Frequency—for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (Fuel and Oil Pressure inputs are pre-terminated) * 4 Outputs: -- Ground -- PWM – for accessories such as fans, boost control, nitrous control, IAC kit, and more -- Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties -- Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR * Integrated data logging to the 3.5 in. hand-held SD card * Free EFI tuning software for complete control of your Terminator X powerplant Terminator X Max ECU Connections: * J1A - Main Harness Connector: This connector is primarily an "Input" connector. It contains all the sensor inputs and wide band oxygen sensor control. * J1B - Main Harness Connector: The second connector is the "J1B" connector (26 pin). This connector is the "output" connector. It has eight injector outputs and outputs for other devices. * MAP Sensor: Used on N/A applications, connect directly to full manifold vacuum port on the intake manifold. * Main Power: Connects to the Main Power Harness; these two wires MUST be wired directly to the battery terminals. * J3: Connection point for the drive-by-wire harness. * J4: Connection point for the transmission harness.

Not Yet Reviewed

$3,149.95

—

$3,649.95

On Sale

Holley HP EFI ECU and Harness Kits

Holley HP EFI ECU and harness kits allow you to manage automotive functions—like the fuel and ignition of your engine, along with controlling nitrous, boost, or water/methanol. Select the model with options needed for your vehicle application. (Note: some models are engine-specific.) Features and notes: * Eight sequentially driven 8:2 peak and hold injector drivers capable of driving up to 16 low or high-impedance injectors are standard * 8-channel distributorless ignition (DIS) outputs capable of directly driving "smart" ignition coils or Holley DIS coils * Integrated, single-channel wideband oxygen sensor control. Works with NTK or Bosch sensors. More channels can be added via CAN bus. * Internal data-logging is standard, with a huge 2GB of memory * 4-stage progressive nitrous control * Turbo boost control * Integrated water/methanol injection control * Self-tuning fuel table strategy greatly simplifies tuning process * Individual cylinder fuel and spark control allow you to unlock your engine's potential * Compatible with 4, 6, and 8-cylinder engines * Unique lbs./hr.-based fueling strategy greatly simplifies tuning * Advanced idle, closed loop, and enrichment strategies allow for very stable operation * Fully potted and can be mounted in the engine compartment or interior * Sealed automotive and marine-grade connectors * Allows for use of common OEM sensors, as well as customer sensor calibration input * Ignition plug-and-play with GM 24x and 58x LSx engines, GM HEI, Ford TFI, magnetic, and hall effect trigger, and other ignition systems * 1-5 bar MAP sensor capability * 2-channel knock control sensor inputs for both one and 2-wire knock sensors * Dedicated fuel and oil pressure inputs * Control both stepper and PWM idle air control (IAC) motors * Speed density, Alpha-N, or combination fueling strategies * Four programmable high or low pulse width modulated (PWM) outputs and four fully configurable inputs can be configured for use * Lean or rich safety cutoff

4.44 out of 5 stars ( 25 )

$2,719.95

$1,843.95

—

$3,949.95

Dorman Remanufactured ABS Control Modules

It's bad news when your wheels lock up and throw you into a skid. The problem could be with your anti-lock braking system. Dorman offers a full line of economical ABS control modules for use on dozens of makes/models. These units are remanufactured from quality materials and fully tested for performance. The modules read the data from your speed sensor and send the correct pressure to each wheel--enabling you to maintain steering control and stop quickly under most conditions. Dorman plug-and-play replacements are upgraded with durable main pump transistors to avoid pump relay burnout. When the ABS light on your dash comes on, retain control of the anti-lock brakes with a newer, dependable module from Dorman.

4.62 out of 5 stars ( 42 )

$351.95

ICT Billet ECM Bench Reader Diagnostic Tuning Tool Harnesses

ICT Billet ECM bench reader diagnostic tuning tool harnesses provide quality connections to ensure proper engine operation and easier diagnoses. Cheaper wire connectors may offer poor quality and conductivity issues, making your job harder. Don't chance it; choose ICT ECM bench reader harnesses. Features and benefits include: * Assembled with OEM-grade TXL wire * Plug-and-play for GM (Gen 3) LS series engine computers * Allows engine computer to be flashed and tuned off the vehicle * Assembled with OEM tooling, OEM Delphi connector, lock, seals, and terminals using OEM harness wire colors * Requires 12 V power source, using power and ground wire, and tuning cable/software for OBDII port

Not Yet Reviewed

$197.99

SCT X4 Power Flash Programmers

SCT X4 Power Flash programmers arrive to you pre-loaded with dyno-proven tune files for select vehicles, to unlock your vehicle's hidden potential! Programming your vehicle with one of SCT's pre-loaded tune files is as easy as 1-2-3. Simply plug the OBD-II connector into vehicle's OBD-II port, select the pre-loaded tune files using the simple to navigate menu and in minutes the X4 programs your vehicle for your particular driving style. Additional features and facts about SCT X4 Power Flash programmers include: * Stores up to 10 custom tune files * Full color LCD display * High-speed data logging/monitoring * Reads/clears DTC trouble codes * Dual analog inputs * Most popular vehicles supported * Installs quickly and easily * Easy restoration back to stock * User adjustable vehicle parameters * USB Interface cable included

4.01 out of 5 stars ( 99 )

$399.00

Edge Pulsar LT Modules

Edge Pulsar LT modules are a one-of-a-kind in-line module that offers feature combinations never before seen in a standalone module. With the Pulsar LT you will be able to adjust throttle response levels, tire size adjustments, TPMS options, speed limiter, and more without having to tune or modify the vehicle. The Pulsar LT connects directly to your vehicle's computer system and makes its changes in-line with the other modules. Utilizing steering wheel controls, the Edge Pulsar LT owners can make all the changes that they desire at any time, driving or parked. The Pulsar LT module, in truth, is multiple products in one. Sure, you can go out and purchase a throttle booster, and then a separate calibration product to adjust tire size and TPMS, and possibly find a custom tuner to adjust the speed limiter but why clutter your vehicle with expensive products that only provide part of the solution you are looking for. The Edge Pulsar LT modules deliver serious options, seamless control, and does so affordably, with an innovative single easy-to-use solution. Product features: * Plug-and-play installation using factory connectors * Multiple throttle sensitivity levels * On-the-fly adjustability via steering wheel controls * Speed limiter adjustment * TPMS Adjustment * Tire size speedometer correction * Axle ratio * Read and delete DTCs * Auto start/stop * AFM/DFM disable * Manual DPF Regeneration * Engine idle up * Allison transmission relearn * Features vary by vehicle model

Not Yet Reviewed

$789.95

Edge EZ Plug-In Modules

These Edge EZ modules unleash the potential of this monster by carefully monitoring rpm, timing, turbo boost pressure, and fueling parameters, and adjusting the fueling and timing to maximize power, torque, and drivability. The Edge EZ modules allow maximum fueling at full turbo boost, and provide an additional 40 to 70 hp and up to 220 ft.-lbs. of torque. Simply plug in the Edge EZ connectors into two stock connections, and you're ready to go. These modules can also be stacked with other upgrades to deliver even more power. They can't be beat for easy installation and power upgrades. Go ahead, install an EZ today and feel the incredible difference it makes!

4.38 out of 5 stars ( 8 )

$562.95

On Sale

aFe Scorcher Blue Modules

aFe Scorcher Blue modules increase fuel pressure, turbo boost, and overall vehicle performance—producing double-digit power gains. Designed with factory-style connectors, they easily connect to engine sensors for a quick and simple installation. The LED control switch can be routed through the firewall into the cabin for a hard-wired solution, or you can connect wirelessly to the module via Bluetooth with the smartphone app. It's a free app in the Apple and Google Play stores, and allows your smartphone to become a hand-held remote. The aFe Scorcher Blue module has four power settings: Stock (green), Sport (yellow), Sport+ (orange), and Race (red). This is the fastest way to safely gain significant horsepower. Order the model designed for your specific vehicle.

5.0 out of 5 stars ( 1 )

$581.00

$522.90

On Sale

aFe Scorcher HD Modules

aFe Scorcher HD modules include a high-quality case and wire harness with factory-style connectors for an easy plug-and-play installation. An LED light switch provides in-cabin, on-the-fly power adjustments. The four power settings are adjustable with one button and the LED light represent the settings: stock (green), sport (yellow), sport+ (orange) and race (red). The aFe Scorcher HD modules add significant power by altering pressure sensor signals to increase turbo boost and fuel pressure to improve vehicle efficiency, power, and throttle response. They use a high-quality aluminum extrusion black powdercoated enclosure casing and factory-style connectors which requires no modification to your factory harness. These factory-style connectors plug directly into the stock wiring harness connectors and sensors.

3.0 out of 5 stars ( 2 )

$451.00

—

$462.00

$405.90

—

$415.80

Haltech Nexus R3 VCU with Universal Wire-In Harness Kits

Haltech Nexus R3 with universal wire-in harness kits are ideal for dedicated race cars, engine swaps and custom wiring jobs. The harness has a set of VCU connectors at one end and unterminated wires at the other. All the wires at the unterminated end are color-coded and clearly labeled. Connect your Haltech VCU to the terminated end and follow your wiring diagram for all the engine connections. Load your base map and you're ready to go! * Color-coded and labeled wires that match the detailed wiring diagram for a confusion free construction process. * The wiring diagram is accompanied by the full ECU manual and software located on the USB key provided with the VCU, or downloadable from the Haltech website. VCU OVERVIEW: * Nexus R3 combines the functionality of a power distribution module, a data logger, a wideband controller, and a state-of-the art engine management system in one powerful device Haltech calls a VCU (Vehicle Control Unit) * 4 x 25A (continuous) push-pull PWM capable (5 kHz) outputs (for power to injectors / coils, transbrake, thermofan, fuel pump) * 8 x peak/hold injector drivers (can be used as low side drive outputs) * 8 x low current ignition outputs (can be used as low side drive outputs) * 6 x low side drive outputs, PWM capable (DPOs) * 6 x push-pull /H-bridge outputs (8A, PWM capable), e.g. for electronic throttle * 11 x 0-5 V analog inputs with redundancy for electronic throttle and switchable 5 V pullup * Trigger and home inputs with differential inputs, adjustable thresholds and glitch filters * 6 x synchronous pulsed inputs, zero crossing or adjustable thresholds - cam sensor inputs, frequency inputs or 0-5 V analog inputs * 1 x on-board wideband controller, supporting NTK and LSU4.9 * 1 x on-board 4 bar MAP sensor * 2 x CAN ports with switchable termination * Suits: Engines with up to 8 cylinders or up to 4 rotors. Racing applications where advanced race features, data logging and power management control are required. * Includes: Nexus R3 VCU, SurLok connectors (red and black), WiFi antenna, mounting bolts, USB-C cable, USB-C dust cap, USB drive with NSP software. Nexus R3 universal wire-in engine harness.

Not Yet Reviewed

$2,799.00

Dorman Remanufactured Transfer Case Control Modules

These Dorman remanufactured transfer case control modules are pre-programmed out of the box and install easily with plug-and-play wiring connectors. Factory transfer case control modules typically fail through corrosion under normal use; this results in the inability to shift in or out of 4WD mode. The modules are fully stress-tested for durability, so you can be sure that your 4WD won't get stuck in or out of gear next time.

4.37 out of 5 stars ( 19 )

$81.99

—

$226.95

On Sale

Holley Terminator X MAX Engine Management Systems

Holley Terminator X MAX engine management systems let you take control of your domestic V8 engine. They give you complete charge of your engine and self-learning fuel strategies, along with the proven, race-winning technology of Holley EFI—all at a budget-friendly price! Every MPFI Terminator X MAX features real-time fuel learn, high-impedance injector drivers, an integrated one-bar MAP sensor—and four programmable inputs and outputs, ideal for electric fans, boost control solenoids, progressive nitrous control, and much more. Also, Holley offers the X MAX systems with either or both drive-by-wire (DBW) throttle body control or transmission control. All kits come fully loaded with base maps for common domestic V8 engine combinations to get you out of the garage and onto the road or track fast. Order the model recommended for your vehicle application. Features include: * Holley EFI industry-leading, easy-to-use software suite allows full laptop access for advanced users * Real-time fuel map learn—takes the guesswork out of tuning your base fuel table * High-impedance injector drivers will safely power most standard injectors and Holley EFI injectors (will not control low-impedance injectors) * Bosch LSU 4.9 wideband relays AFR information to the ECU for accurate reading and precise tuning control * On-board one-bar MAP sensor is perfect for N/A or nitrous engine combos * MAP sensor vacuum hose adapters * 4 inputs: 12 V, ground, 5 V, and frequency * 4 outputs: Ground, PWM, and for accessories * Boost control: boost vs. time, boost vs. gear, boost vs. rpm, boost vs. speed, and boost safeties * Nitrous control: single channel of wet or dry, progressive or non-progressive, rich/lean safeties, and target closed loop AFR; adjustable through touch screen * Advanced tables can be used for any custom tables * On-board diagnostic LEDs allow you to identify any critical engine issues at a glance * The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDs must face up! * Plug-and-play compatible with more Holley EFI accessories * Available with or without a 3.5 in. touch screen LCD hand-held with easy-to-use calibration wizard; allows you to quickly build a base tune for most V8 engines, as well as tuning and gauge display functions

4.18 out of 5 stars ( 92 )

$1,849.95

—

$2,559.95

$1,663.95

—

$2,302.95

12 Results Found For "gm electrical connector"