Availability
Summit Bucks
Daytona Twin Tec wideband exhaust gas oxygen sensors are replacements used in a variety of tuners, data-logging controllers, and gauges—including WEGO 3 and Twin Scan 3. Ensure that your performance calibrations are correct with an O2 sensor from Daytona.
( 1 )
$150.95
Summit Bucks
Dyna 2Ki Programmable Ignitions not only add to, but extend, many features of the Dyna 2000 modules with a completely new design that fits under the cam cover. Every time power to the ignition is switched on, the 2Ki checks to see if the coil is shorted, mis-wired, or of the wrong type. If an error is detected, the 2Ki will immediately switch off and issue a warning. After starting, the 2Ki continuously monitors the status of the coil and wiring. All 2Ki ignitions are PC programmable: * 8-point fully-definable wide-open throttle curve * 8-point fully-definable part-throttle curve * Rev limit programmable in 50 rpm steps * Programmable dead cranking revs 0-10 * Programmable rear cylinder offset, total of +/- 10 degrees Data recording functions: * Total engine hours * Time at wide-open throttle * Number of engine starts * Longest time operating at wide-open throttle * Maximum rpm * Seconds near rev limit * Statistical analysis of time at rpm Additional features and benefits include: * Single-fire operation down to zero rpm for easier cranking and kicking * Operates in all combinations of single-fire or dual-fire with single plug or dual plug heads (when used with appropriate coils) * Eight advance curves to cover a broad range of engine builds and riding styles * Over-rev protection adjustable from 6000 to 7500 rpm * Adjustable timing retard for nitrous and turbo applications * VOES indicator; shows the status of the VOES switch, also indicates when retard mode is active * Built-in tach driver delivers stable tach signal even during rev limiting; can be used to activate shift lights, auto shifters, and other accessories * Easy static timing with built-in timing indicator (no timing light required) * Intelligent over-current and short circuit protection * Active dwell control continually adjusts coil current to maintain maximum spark energy up to redline while eliminating coil stress caused by overcharging at idle * High-efficiency design reduces battery draw for easier cold weather starting and lower charging system load * Ruggedized output--cannot be damaged by broken or disconnected spark plug wires * Over-voltage protected against momentary spikes (positive and negative) as well as surges caused by faulty voltage regulators or quick-charge battery boosters * Harness constructed with TXL cross-linked polyethylene automotive wire for exceptional resistance to abrasion, heat, and chemical attack * High-temp glass-braid jacket further increases the toughness of the harness and provides a tight, clean appearance * Wire colors closely match the factory harness for error-free installation * Manufactured with premium-quality components designed for operation in a high-temperature, high-vibration environment * One-piece aluminum housing and thermally-conductive epoxy encapsulation provide superior heat dissipation and outstanding shock, vibration, and moisture resistance * Advanced microprocessor technology * Quartz crystal accuracy.
Not Yet Reviewed
$418.99
Summit Bucks
FAST XDi EZ-RUN distributors are convenient packages that save time and space. These units do not require an ignition box to fire the coil, and their standard-size caps offer more firewall and manifold clearance than HEI-style distributors. XDi EZ-RUN billet distributors feature mechanical and vacuum advance for easy setup and use. They also feature a built-in electronic module that can directly fire an ignition coil, while delivering accurate, dependable, and maintenance-free operation. Ideal for both carbureted and EFI conversion engines, EZ-RUNs are a perfect choice for daily drivers, musclecars, and street rods. FAST XDi EZ-RUN distributors are available for most domestic V8 applications. Choose the model designed for your year/make and engine application.
( 2 )
$297.95
—
$382.95
Summit Bucks
Performance Tool T-handle spark plug socket tools are exactly what you need for those confined, hard-to-reach spaces. They feature drop-forged steel construction and are chrome plated to resist corrosion. The tools also include a neoprene insert to grip and protect your plugs. Order the socket size needed for your application.
( 6 )
$9.99
Summit Bucks
When your motorcycle needs optimum performance from a small package, you'll want Dynatek Twin Fire II mini coils. Their primary and high-voltage terminals are machined from brass, they use high-impact thermoplastic housings, and their compact size easily fits on the bike. These mini coils accept 7 to 8.8mm wires, have a peak gap current over 50mA, and conduct over 40,000 V output. They are only usable with internal dwell control ignitions. Dynatek Twin Fire II mini coils incorporate two individual performance ignition coils into one easy-to-mount package.
Not Yet Reviewed
$153.99
Summit Bucks
Dynatek Dyna Dual S ignitions replace stock type ignition systems which are self-contained and fit under the stock timer cover. Dynatek Dyna Dual S ignitions unique hall-effect sensors are impervious to dirt and oil and spark scatter is almost eliminated. Dual S ignitions changes timing less than 3 degrees from 0-8,000 rpm and eliminates maintenance and extends spark plug life.
Not Yet Reviewed
$120.99
Summit Bucks
Dynatek 2000 digital HD2 ignition systems have become the standard for performance and versatility in aftermarket ignitions. These new modules include expanded advance curve functionality, with the option to use vacuum advance compensation. The new modules also include a special retard mode for use with turbocharged and nitrous bikes. They allow you to tailor the advance curve and rev limiter with four built-in advance curves and four independent rev limiter choices from 6,000 to 7,500 rpm. They are stock factory pick-ups and simply plug into the existing factory wiring harness on 1991-98 model bikes. An extension harness is available for installing the Dyna 2000 on 1990 and earlier bikes.
Not Yet Reviewed
$242.99
Summit Bucks
Performance Tool spark plug socket kits include 14mm, 18mm, 13/16 in., 5/8 in., and 3/4 in. sockets to cover most standard automotive applications. Made from durable vanadium steel and chrome plated for corrosion resistance, the 3/8 in. drive accessories are clearly labeled and will deliver years of reliable service.
( 4 )
$19.99
Summit Bucks
Dynatek 2000 digital HD1 ignition systems have become the standard for performance and versatility in aftermarket ignitions. These new modules include expanded advance curve functionality, with the option to use vacuum advance compensation. The new modules also include a special retard mode for use with turbocharged and nitrous bikes. They allow you to tailor the advance curve and rev limiter with four built-in advance curves and four independent rev limiter choices from 6,000 to 7,500 rpm and the new retard mode allows for a selection of ignition retard of 5, 7, or 10 degrees upon activation of retard input. They're stock factory pick-ups and simply plug into the existing factory wiring harness on 1991-98 model bikes. An extension harness is available for installing the Dyna 2000s on 1990 and earlier bikes.
Not Yet Reviewed
$242.99
Summit Bucks
Performance Tool spark plug sockets feature chrome vanadium or alloy steel construction for strength and durability, with a polished nickel chrome plated finish to resist corrosion. Each socket features recessed edges, and large openings to help reduce fastener rounding, and is size stamped for quick and easy identification. Performance Tool offers spark plug sockets in a choice of SAE or metric sizes, and in lengths, and styles to suit your needs.
( 7 )
$3.99
—
$12.99
Summit Bucks
Delphi mass airflow sensors are the OE parts that your vehicle should have come with! Their MAF sensors are new, not remanufactured, and feature fast response for outstanding performance over a wide range of ambient temperatures. Delphi mass airflow sensors are engineered to provide your ECM with continuous, precise information to ensure optimal performance, fuel economy, and reduced emissions. Give your vehicle new life--replace worn OE parts with Delphi mass airflow sensors.
( 99 )
$81.99
—
$191.99
Summit Bucks
Daytona Twin Tec internal ignitions mount in the nose cone while replacing the factory ignition. The results are a cleaner look by having less visible wire. This is good news to the custom builder. These ignitions feature adjustable advance modes and slopes that work on stock to modified applications. Daytona Twin Tec internal ignitions are protected by a billet aluminum housing and works with your factory rotor. Other features: * Digitally set rpm limit set in 100 rpm increments * Selectable single or dual fire mode * Selectable kick start mode * Selectable multi-spark mode for quick starting and smooth cruising * Coil outputs protected against short circuit * Optional USB interface and software for custom advance programming
Not Yet Reviewed
$402.95
—
$449.95
Summit Bucks
Dynatek TC88-2P ignitions are easy to install and make a big difference on takeoff and on smoothness. They are single-fire performance systems with eight rev limiter settings, constant full spark energy, and 16 programmable advance curves. Stock connectors and mounting make fine-tuning easy. Data recoding features the number of engine starts and total hours running, maximum rpm, and time at wide open throttle.
Not Yet Reviewed
$298.99
Summit Bucks
If you're experiencing an original equipment malfunction or simply looking for a more adaptable and tunable upgrade, Daytona Twin Tec TC88 Plug-In ignition modules offer timing advance modifications to accommodate stock-to-customized engines. Their adjustability factor and easy plug-in installation are the big reasons for their use, as well as their easy-to-dial-in digitally set rpm limits with a selectable multi-spark mode for quick starting and smooth cruising. Daytona Twin Tec's product focus is electronic fuel injection and ignition systems for Harley-Davidson® motorcycles. These modules support all sensors, including theft/security systems. An optional USB interface and software for programming custom advance curves are available.
Not Yet Reviewed
$386.95
Summit Bucks
Performance Tool fuse assortment kits are available in a variety of sizes, styles, and quantities to meet all of your automotive needs. Always be prepared; order the electrical fuse kit tailored to your replacement or custom build projects.
( 11 )
$3.99
—
$21.99
Summit Bucks
Performance Tool battery terminals are high-quality replacements to help ensure a strong start every time you turn the ignition. They're available in a variety of styles for applications such as autos, trucks, and marine. Why struggle with aging or corroded terminals? These small battery accessories are easy to install—and deliver the reliable performance you expect each day. Order the model best suited for your battery setup.
( 3 )
$3.99
—
$22.99
Summit Bucks
Dynatek single output performance replacement coils combine high-tech and quality design for maximum performance. They produce excellent spark energies and over 30,000 V output. It is recommended to use these coils with 5.0 ohms primary resistance for street use, and 3.0 ohms primary resistance for racing applications.
Not Yet Reviewed
$182.99
Summit Bucks
Tune your carburetor or fuel injection system with Daytona Twin Tec WEGO III wide-band exhaust gas oxygen sensor systems. These stand alone units have built in data logging so you can analyze the data logged and make the corrected changes. Daytona Twin Tec WEGO III wide-band exhaust gas oxygen sensor systems will log over 2 hours of data including AFR, and engine RPM. They are available in a single channel or dual channel unit. Other features: * Includes WEGO III unit, Bosch LSU4.2 wide-band oxygen sensor (2 for dual channel), 18x1.5mm weld nut (2 for dual channel), and software on CDROM. * Unit can be programmed to display Lambda or correct AFR values for any hydrocarbon fuel with a known stoichiometric ratio * Suitable for motorcycle, automotive, and other small engines * Measurement range is 10.3 to 19.5 gasoline AFR or 0.70 to 1.33 Lambda * Bright daylight readable blue LED display with automatic dimming * Built in USB interface * Fully encapsulated with water proof LED display
Not Yet Reviewed
$614.95
Summit Bucks
Just do it. Installing Daytona Twin Tec TC88 ignition kits are one of the best things you can do to your bike. With them, you'll pull harder, start faster, won't foul the plugs, and it'll idle great, too. If you're looking for a more adaptable and tunable upgrade and timing advance modifications to accommodate stock to customized engines, their adjustability factor and easy plug-in installation are the big reasons for their use, as well as the easy to dial-in, digitally set rpm limits with a selectable multi-spark mode for quick starting and smooth cruising. Daytona Twin Tec's product focus is electronic fuel injection and ignition systems for Harley-Davidson® motorcycles. These modules support all sensors, including theft/security systems, and include the TC88 ignition, coil, and wire sets. An optional USB interface and software for programming custom advance curves are available.
Not Yet Reviewed
$484.95
—
$595.95
Summit Bucks
Quarter Master Ultra-Duty starters give your race car a good start to a great finish! These mini starters are ready for track duty with massive cranking power, heavy-duty solenoid and bearing assemblies, and CNC-machined billet aluminum adapter mounts for increased torque and a precision flywheel fit. Quarter Master Ultra-Duty starters are ready to meet the temperatures and demands of your high-compression engine. Think you're saving money buying a less expensive starter? Inferior starters will leave you cold on the street and track--not good! Bolt on the power to get started--bolt on track-tested Ultra-Duty starters from Quarter Master.
( 2 )
$403.52
—
$689.71
Summit Bucks
Daytona Twin Tec Model 1006 and 1007 external ignition kits are external plug-in ignition modules for 1990 and later Harley-Davidson® Evolution Big-Twin and 1990-1993 Sportster models. They offer a wide timing advance adjustment range that accommodates stock to highly-modified engines. Features include: * Digitally set rpm limit in 100 rpm steps * Selectable single or dual-fire modes * Selectable multi-spark mode for quick starting and smooth cruising * Coil outputs protected against short circuits * Available USB interface and software for programming custom advance curves (sold separately) * Billet aluminum housing with black anodized finish * Easy plug-in installation
Not Yet Reviewed
$476.95
Summit Bucks
Secure your battery with Performance Tool battery hold-downs. They are available in a choice of styles to fit your needs. The cross bar style hold-downs feature a heavy-duty steel construction and are vinyl coated for corrosion resistance and includes hardware, while their universal hold-down strap has a solid rubber construction with nylon inserts for strength. The J-bolt and the L-bolt hold-down sets accommodate cross bar/frame designs. They have heavy-gauge steel construction and are zinc or chrome plated to resist corrosion. Select the battery hold-downs designed to fit your needs.
( 7 )
$5.99
—
$8.99
Summit Bucks
Motorcyclists, connect your Daytona Twin Tec controllers to your laptop with these special USB interface cables. They include all required adapters for ignition and fuel injection systems. These cables allow you to easily interface with all Dayton Twin Tec engine controls.
Not Yet Reviewed
$119.95
Summit Bucks
Daytona Twin Tec high output coils are the same size as the OEM version, but much stronger. These twin-cam coils have 0.5 ohm resistance, greater than 50mJ—and over 40,000 V output.
( 1 )
$119.95
—
$130.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
