Availability
Showing In Stock Items. Show All 8 Items.
Holley Terminator X engine control modules are standalone units intended for use as service components for your Terminator X EFI installation. Each ECU features real-time fuel learn, high-impedance injector drivers, an integrated 1 Bar MAP sensor, and four programmable inputs and outputs. The inputs and outputs are ideal for electric fans, boost control solenoids, or progressive nitrous control. Order your Holley EFI Terminator X Service ECU today. Features: * Compatible with Terminator X harnesses * OEM (Original Equipment Manufacturer) injectors supported with part numbers provided in the handheld wizard or software * Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * Eight built-in multi-color diagnostic LEDs allow you to quickly identify a variety of potential system issues, such as: -- A failed TPS (Throttle Position Sensor) Autoset -- Faulty crank or cam sensors -- Potential oxygen sensor issues * Built-in 1 Bar MAP (Manifold Air Pressure) sensor -- On boosted applications, you can disable the internal MAP sensor and utilize an external MAP sensor * Four inputs—12 V, Ground, 5 V, and Frequency for things, such as: -- Additional pressure sensors -- Activation triggers for nitrous activation -- A trans-brake (Fuel and Oil Pressure Inputs are pre-terminated) * Four outputs--Ground, PWM, and accessories such as: -- Fans, boost control, nitrous control, IAC kit, and more * Boost control: -- Boost vs. Time/Gear/RPM/Speed, and boost safeties * Nitrous control: -- Single channel of wet or dry -- Progressive or non-progressive -- Rich/lean safeties -- Target closed loop AFR * Advanced tables: -- Four 1D tables -- One 1D per gear table -- Four 2D tables -- One 2D per gear table * Free EFI tuning software for complete control of your Terminator X powerplant
Not Yet Reviewed
$849.95
DIYAutoTune MegaSquirt Gen 2 plug-and-play engine management systems are standalone units designed as direct-fit, factory ECU replacements offered for a variety of foreign and domestic vehicles. These powerful and cost-effective options typically require an hour or less for installation, and each includes a base map to get the motor fired up easily and ready for fine-tuning to match your engine's needs--from mild to wild. MegaSquirt Gen 2 ECUs get the job done with an impressive feature list that will let you do a lot more than you'd expect anywhere near this price point. DIY AutoTune MSPNP Gen 2 ECUs typically feature: * Fully plug-and-play installation--no wiring required for basic functionality * Base map is pre-loaded to help your engine start on the first turn of the key * Real-time tuning and data-logging with a laptop connection * Supports most aftermarket wideband sensors * 16 x 16 fuel tables allow high-resolution tuning * 12 x 12 ignition tables * Multiple acceleration enrichment strategies * Closed-loop idle speed control * Air conditioner control * Onboard peak and hold drivers support both high and low impedance injectors--no external ballast resistor is needed * Allows removal of stock airflow meter or stock MAF sensor, if so equipped * 12 x 12 air fuel ratio target tables for use with wideband oxygen sensor for precise tuning and table trim * Built-in 2-step rev limiter/launch control with flat shift * Real-time barometric correction * Internal 4-bar MAP sensor reads up to 44 psi of boost * Over-boost protection * Closed-loop boost control (requires boost solenoid kit) * Knock sensor input with adjustable sensitivity * Headphone output for knock sensor--listen for knock while you tune! * Table switching input--change fuel and spark maps on the fly for different fuels, nitrous activation, etc. * Input for flex fuel sensor--switch between E85 and gasoline on the fly! * CAN Bus connector allows interconnection of other MegaSquirt-compatible devices for additional functions, like: EGT input, automatic transmission controller, additional sensors ... the possibilities are limitless! * MegaSquirt Gen 2 plug-and-play ECU * MSPNP RS232 serial tuning cable, 6 ft. (USB adapter sold separately, if needed) * Tuning software and documentation USB stick * 6 ft. vacuum hose for MAP signal and "T" fitting * Four screws for ECU mounting
( 2 )
$869.99
Fear not, fuel injection fans! FAST has just made it easier than ever to convert your engine from a carburetor to fuel injection, using these FAST EZ-EFI Self-Tuning engine management systems. The most important feature is the self-tuning operation that does not require chasing components, expert tuning experience, or a laptop computer to tune. Simply hook them up, answer the basic Wizard setup questions on the included hand-held display, and the systems truly tune themselves. FAST EZ-EFI Self-Tuning systems include a wide-band oxygen sensor and wiring harness.
( 3 )
$801.95
FiTech presents Ultimate LS standalone ECUs. These self-learning ECUs are offered with and without transmission control. So if you're considering utilizing a factory intake, throttle body, and injectors, FiTech Ultimate LS standalone ECUs will get your engine ready for optimal performance.
( 51 )
$959.00
FiTech Ultimate TPI standalone ECUs bring an old GM TPI-controlled engine (L98, LB9) into modern times. These standalone EFI kits plug into all existing sensors on a GM TPI engine and provides complete control of the engine. From timing control to self-learning fueling, FiTech Ultimate TPI standalone ECUs deliver new life into the GM TPI engine.
( 9 )
$847.00
—
$1,060.00
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
