Availability
Showing In Stock Items. Show All 79 Items.
FiTech presents Ultimate LS standalone ECUs. These self-learning ECUs are offered with and without transmission control. So if you're considering utilizing a factory intake, throttle body, and injectors, FiTech Ultimate LS standalone ECUs will get your engine ready for optimal performance.
( 51 )
$567.00
LS Classic Series distributor and plug wire sets are the perfect way to top-off your vintage appearing LS swap. LS Classic Series starts with a set of high-quality 7mm Kevlar® spiral core spark plug wires with high-temp silicone pre-installed 90 degree coil boots and straight unterminated spark plug boots. The wires are 9 ft. long with 40 ohms of resistance per ft., giving you all the length and performance you need to remote mount your coils—so they're out of sight and out of mind. The plug wires first connect to the coils and then pass into the hollow cast-aluminum distributor body that is bolted to the engine's valley plate. The wires continue on to the spark plugs through the distributor for an authentic nostalgic look. Top-off your vintage appearing LS swap perfectly with one of these distributor and plug wire sets by LS Classic. Note: These distributors are designed to bolt to the back two bolts of LS Classic valley pans and will not clear valley plates with raised ribs or oil pressure sender bosses.
Not Yet Reviewed
$724.95
As LS engines make their way onto the race track MSD is ready with the Circle Track LS ignition controls. You're off to the races with MSD. Circle Track LS ignition controls feature: * Direct plug-in to factory GM LS sensors and coils * Preprogrammed to run the GM CT525 crate engine out of the box * Laptop programmable rpm limit, timing curve, and coil selection for custom tuning * Auto detects coils, cam sensor, and crank sensor * Will run 24x 1x, 58x 1x, and 58x 4x crank/cam sensor combinations * Self-powered with USB for laptop programming * Steady, accurate timing control * Dedicated plug for Tech Official
Not Yet Reviewed
$562.95
Holley LS extended-length main engine harnesses are 22 in. longer than previous harnesses. Designed to fit most 24x and 58x LS engines from 1997-2012, they are a perfect fit for installers wanting to mount any Holley EFI ECU inside of the passenger compartment where it is away from the elements, and easy to access, such as on a roll bar or under the passenger seat. Notes: * Plug-and-play with Dominator, HP, Terminator X, and Terminator X Max ECUs * LS1/6 harness interfaces with 24x crank and 1x cam sensors * LS2/3/7 harness interfaces with 58x crank and 4x cam sensors
( 1 )
$688.95
Haltech's Elite 2000/2500 GM Gen IV LS/LSX Non-DBW terminated harness is the fastest and most cost-effective way to wire your race car or engine conversion! Simply connect a handful of labelled wires and this plug-and-play product allows you to be up and running in just a few hours. When installed in conjunction with a Haltech Elite ECU, this harness opens the door to virtually limitless performance modification and tuning of your vehicle. * Injector Connector harness options: Bosch EV1 or Bosch EV6 * Quick start guide will walk you through installation of the harness * Guide is accompanied by the full ECU manual and Software located on the CD or USB key provided with the ECU to refer to while completing your installation and configuration * Programmable systems allow you to extract all the performance from your engine—by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions * Suits: Common U.S.-style Delco/Bosch GM alternator connector. Pre-wired to connect directly to OEM 7 Pin Coil Harness Connector. Manual transmission only. * Includes: Engine harness with fuse block and firewall grommet * Notes: Please confirm your alternator connector (See the product quick start guide) and order an alternator adapter if required. (HT-040090 or HT-040091) LS2 Ignition coils and harnesses are NOT included.
Not Yet Reviewed
$670.00
Haltech's Elite 2000/2500 GM Gen IV LS/LSX DBW Ready terminated harness is the fastest and most cost-effective way to wire your race car or engine conversion! Simply connect a handful of labeled wires and this plug-and-play product allows you to be up and running in just a few hours. When installed in conjunction with a Haltech Elite ECU, this harness opens the door to virtually limitless performance modification and tuning of your vehicle. * Injector Connector harness options: Bosch EV1 or Bosch EV6 * Quick start guide will walk you through installation * Guide is accompanied by the full ECU manual and software located on the CD or USB key provided with the ECU to refer to while completing your installation and configuration * Programmable systems allow you to extract all the performance from your engine—by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions * Suits: Common U.S.-style Delco/Bosch GM alternator connector. Pre-wired to connect directly to OEM 7 Pin Coil Harness Connector. Manual transmission only. * Includes: Engine harness with fuse block and firewall grommet. * Notes: Please confirm your alternator connector (See the product quick start guide) and order an alternator adapter if required. (HT-040090 or HT-040091) LS2 Ignition coils and harnesses are NOT included.
Not Yet Reviewed
$670.00
MSD ignition controls are the most successful aftermarket ignitions ever made. The multiple spark design has won races and championships in every type of motorsport. MSD ignitions are consistent, reliable and durable, even under extremely harsh conditions. The results speak for themselves--more power, easier starting, quicker throttle response, smooth idle, and improved fuel consumption.
( 37 )
$562.95
—
$564.95
Holley's EFI crank trigger kits provide accurate crank speed and position signals to Holley EFI systems in the most demanding, high-horsepower, racing applications. The crank position is measured every 10 degrees instead of every 45 degrees, like standard 4-magnet crank trigger systems. Holley's EFI crank trigger kits feature 1/4 in. thick, billet steel, 36-1 or 60-2 tooth-crank trigger wheels with black zinc oxide finish for superior corrosion resistance and striking good looks Other notable features include: * Crank wheels center off of balancer hubs, eliminating the need for centering rings * All billet, 6061-T6 aluminum sensor mounting brackets with "bright-dipped" black anodized finish and laser-etched Holley EFI logo * Custom 3-wire, ferrous-target, Hall-effect sensors with M12 x 1.0mm threads for finer gap adjustment * Grade 8 and mil-spec mounting hardware
( 6 )
$665.95
Meziere True Start 300 Series high-torque starters are recommended for all high-compression, large displacement engines up to 565 cu. in. and supercharged applications. They use an optimized planetary gear reduction to deliver maximum engine cranking speed—and supported nose to provide rigidity for reliable gear alignment. Their innovative billet aluminum head design provides the strongest drive gear support without an external nose support. The starter block features a full 360 degrees of clocking positions in 10 degree increments. Meziere True Start 300 Series high-torque starters feature a custom Bendix to ensure excellent longevity. Order the model designed for your vehicle application.
( 5 )
$662.40
Chevrolet Performance engine controllers are individual units for your LS crate engine. They are identical to those included in their kits. Maintain the intellect of your Gen III/IV LS or Gen V LT-powered project vehicle with the "brains" designed to work flawlessly--Chevrolet Performance engine controllers.
( 1 )
$740.79
JMS Chip Smart Spark Tran AM TA2 ignition systems are complete plug-and-play racing ignition systems specifically designed to be used on LS-based TA2 racing engines. These fully encapsulated devices are preprogrammed with approved TA2 ignition timing advance tables. This TA2 Super Speedway version has been designed after JMS Chip's Daytona sensors Smart Spark ignition system and then created to meet specific Trans Am TA2 racing requirements. Order the model you need. Product features and details: * Smart Spark TA2 SS—LS supports approved TA2 GM LS racing engines (carbureted LS engines with 58-tooth crank trigger) * Preprogrammed with approved TA2 ignition timing advance tables * Unit is sealed for the TA2 racing series * Status LEDs—display device and trigger input status * Fully encapsulated construction * Heavy-duty 12-pin Deutsch connectors used for signal connections
Not Yet Reviewed
$599.75
On Sale
MSD flying magnet crank triggers use four magnets permanently embedded in an aluminum wheel. As the crank rotates, the magnets pass a non-magnetic pickup, which triggers the ignition. These MSD systems include a trigger wheel, pickup, CNC-machined aluminum mounting bracket, and hardware.
( 52 )
$716.95
On Sale
MSD DynaForce starters are built with all-new components and hand-assembled in the USA. For maximum performance and reliability, all starters are dyno-tested and blueprinted before they leave the factory. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement during thousands of starts. MSD DynaForce starters feature a 3.4 hp motor—and a reduced 4.4:1 gear ratio delivers superior torque to start high-compression race engines up to an 18:1 ratio. They include a downsized housing that clears most headers and oil pans, and a billet aluminum mounting block that can be clocked in different positions for tighter clearance applications. These starters are available in a durable red or black powdercoat finish that's designed for maximum protection while looking good. They use a nickel plated, heavy-duty solenoid for optimum performance in severe environments. Order the model designed for fitment with your vehicle application.
( 242 )
$511.95
Granatelli Motor Sports Pro Series Xtreme coil packs output a whopping 65,000 V, making them the undisputed king of coils. Specifically designed for supercharged, turbocharged, and high-level nitrous applications, these Xtreme coils will not suffer the spark blowout common in weaker coils. And, thanks to Granatelli's patented isolator rings, there is 0 ohm resistance and no RFI/EMI interference. Up your engine's power to perform with a set of Pro Series Xtreme coil packs from Granatelli Motor Sports.
( 13 )
$712.22
—
$747.83
Upgrade your boat's charging system with MechMan high-output marine alternators. These certified high-output, 170 amp 6-phase alternators feature 12 diodes and twin rectifier plates for excellent durability with high-end audio installations. They include a 6-groove serpentine pulley and meet or exceed SAEJ1171, ISO 8846, and USCG Title 33 standards for ignition protection. MechMan marine units are hard black anodized, then grey enamel coated to provide the best possible corrosion resistance. All MechMan does is alternators. So, when you need a bolt-in, high performance charging solution for your boat, MechMan high-output marine alternators should be your choice.
Not Yet Reviewed
$519.00
Haltech's Elite 2000/2500 GM Gen III LS1/LS6 Non-DBW terminated harness is the fastest and most cost-effective way to wire your race car or engine conversion! Simply connect a handful of labelled wires and this plug-and-play product allows you to be up and running in just a few hours. When installed in conjunction with a Haltech Elite ECU, this harness opens the door to virtually limitless performance modification and tuning of your vehicle. * The quick start guide will walk you through installation * The guide is accompanied by the full ECU manual and software located on the CD or USB key provided with the ECU to refer to while completing your installation and configuration * Fully programmable systems allow you to extract all the performance from your engine—by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions. * Suits: Factory EV1 injector connectors and common U.S.-style Delco/Bosch GM alternator connector. Pre-wired to connect directly to OEM 7 Pin Coil Harness Connector. WBC1/2 CAN O2 wideband controller ready (controller and sensors not included) * Includes: Engine harness with fuse block and firewall grommet * Notes: Please confirm your alternator connector (See the product quick start guide) and order an alternator adapter if required. (HT-040090 or HT-040090) Ignition coils and harnesses are NOT included, Please order 8 x HT-020102 and/or HT-045657 if required.
Not Yet Reviewed
$670.00
Haltech's Elite 2000/2500 GM Gen III LS1/LS6 DBW Retrofit Ready terminated harness is the fastest and most cost-effective way to wire your race car or engine conversion! Simply connect a handful of labelled wires and this plug-and-play product allows you to be up and running in just a few hours. When installed in conjunction with a Haltech Elite ECU, this harness opens the door to virtually limitless performance modification and tuning of your vehicle. * The quick start guide will walk you through installation * The guide is accompanied by the full ECU manual and software located on the CD or USB key provided with the ECU to refer to while completing your installation and configuration * Programmable systems allow you to extract all the performance from your engine—by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions. * Suits: Retrofit of a GEN IV LS2/3 DBW throttle body. Common U.S.-style Delco/Bosch GM alternator connector. Pre-wired to connect directly to OEM 7 Pin Coil Harness Connector. WBC1/2 CAN O2 Wideband Controller ready (Controller and sensor(s) not included) Manual transmission only. * Includes: Engine harness with fuse block and firewall grommet * Notes: Please confirm your alternator connector (See the product quick start guide) and order an alternator adapter if required. (HT-040090 or HT-040091) Ignition coils and harnesses are NOT included, Please order 8 x HT-020102 and/or HT-045657 if required.
Not Yet Reviewed
$670.00
On Sale
MSD Smart Coils were developed to produce more spark energy while consuming less power without sacrificing voltage output. This means you get hotter spark at the plug to burn the maximum amount of fuel in each cylinder while using less power from your electrical system. Smart Coils are compatible with popular aftermarket electronic fuel injection systems and will run on traditional 12 V or 16 V electrical systems found in race applications. The coils feature unique elongated mounting holes to accommodate popular mounting brackets or allow them to bolt in place of an LS coil with 72mm bolt spacing.
( 1 )
$927.95
—
$995.95
$716.82
—
$717.30
On Sale
MSD Ignition's Multiple Spark Coils (MSC) will fit in place of the stock GM LS coils and connect directly to the factory connectors. Once installed, you'll have the power and performance of higher energy sparks, crowned with MSD's multiple spark discharge. Increased spark energy and voltage, along with multiple spark capabilities, help improve the combustion process of the fuel mixture to create an efficient burn. This results in improved throttle response, smooth idle and quick starts, plus increased high rpm performance!
( 26 )
$977.95
—
$991.95
$559.16
—
$749.96
Choose EFI main power wiring harnesses from Holley to meet your needs. Several choices are offered—TBI, LS applications, multi-point, and un-terminated harnesses—to feed and carry your engine's electrical supply. Get wired for electronic fuel injection with Holley EFI systems main wiring harnesses.
Not Yet Reviewed
$562.95
—
$588.95
On Sale
MSD Pro 600 CDI ignition high-output coils developed these powerful coils to provide unrivaled spark energy and dependability. The best choice to equip your Pro 600 CDI, they have the highest current and voltage available in a small compact design, creating over 200 millijoules of spark energy and leaving no horsepower untapped. Along with the unrivaled output of your Pro 600 CDI, MSD high-output coils, everything from Pro-mod's to pulling trucks can perform at a whole new level! Features and benefits: * Designed for extreme racing for the Pro 600 Capacitive Discharge Ignition * Capable of up to 50,000 V to ignite extreme cylinder pressures * Over 200 millijoules of spark energy makes them ideal for use with methanol, ethanol, and E85, as well as forced induction and power adder combinations * Supplied with hardware to mount horizontal or vertical position * Coils are designed to be mounted on Holley's LS valve covers, or OE LS passenger car coil brackets using 72mm bolt spacing * HEI-style secondary tower for secure coil wire connection
Not Yet Reviewed
$790.95
$608.22
HP Tuners Introduces VCM Suite MPVI4 Credit Pro packages, the latest evolution of their industry-leading OBDII interface. Built for professionals and enthusiasts alike, the computer programmers connect your vehicle to VCM Suite software (5.2+) for faster, smarter, and more powerful tuning and diagnostics than ever before. With upgraded hardware, expanded connectivity, and future-ready Wi-Fi capabilities, the MPVI4 redefines what's possible in performance calibration and data acquisition. Models are available with 0, 2, 4, 6, or 8 credits. HP Tuners VCM Suite MPVI4 Credit Pro packages feature: * Improved standalone logging: the most powerful device yet, capable of delivering standalone logging performance on par with VCM scanner and a wired connection * Upgraded hardware architecture: New internal processor for improved data throughput and flashing performance; 30x more memory than previous generation MPVI3 * High-speed USB-C connectivity: Faster, more reliable communication with your PC and vehicle * Bluetooth 5.2: Seamless wireless connection for scanning, logging, and TDN support * Wi-Fi ready (future update): Wireless VCM Suite connectivity coming soon * Enhanced storage and efficiency: Increased onboard memory for robust logging sessions * Improved OBDII fitment: A revised, tapered design means a more secure connection and better compatibility with even more makes/models * Built-In Pro feature set: Standard on every MPVI4, enabling standalone data logging and external sensor integration with PROLINK+ * RGB status LEDs: Clear visual indicators for power, connection, and activity status * Cross-Platform Compatibility: Works with VCM Suite (5.2+), TrackAddict, and RaceRender
( 2 )
$599.95
—
$699.93
SCT Livewire TS performance programmer and monitors let you tap your ride's hidden performance and excitement! SCT Livewire plus touch screens are easy to set-up, use, and navigate to quickly upgrade your boring factory-calibrated vehicle computer for a high performance driving experience. These tuner kits are available for both gas and diesel vehicles plus they include a windshield mount to keep your data at eye level. You're not like everyone else and your driving experience doesn't need to be mediocre! Power tune with SCT Livewire TS Plus performance programmer and monitors. SCT Livewire TS Plus features: * Color 4 in. touch screen display * Rear view camera input * Automatic on/off/sleep mode * Holds up to 10 custom tunes * Reads and clears DTC codes * Built-in performance calculator * High-speed data logging and monitoring * User adjustable tune options * User selectable graphics and gauge layouts * User adjustable warnings/alerts * Adjust for different size fuel injectors * Disable CMCV to prevent CEL * Remove, increase, or decrease vehicle's speed limiter * Increase or decrease idle speed * Disable traction control * Add or remove timing by rpm range * Add or remove fuel at wide open throttle * Change transmission shift pressure - automatic transmissions only * Set gear ratio to correct shift patterns and vehicle's speedometer * Set tire size to correct shift patterns and vehicle's speedometer * Stores vehicle's stock file before programming * Supports and holds custom tunes * Adjust electric fan engagement temperature Custom Tune File Adjustable Options: * Increase or decrease idle speed * Remove, increase, or decrease vehicle's rpm limiter in Drive * Remove, increase, or decrease vehicle's rpm limiter in Neutral * Remove, increase, or decrease vehicle's speed limiter * Adjust electric fan engagement temperature * Add or remove fuel at wide open throttle * Set gear ratio to correct shift patterns and vehicle's speedometer * Set tire size to correct shift patterns and vehicle's speedometer * Increase or decrease the wide open throttle shift points of each gear individually * Change transmission shift pressure - automatic transmissions only
( 53 )
$599.00
On Sale
When it comes to late model performance parts, nothing beats bolt-on and direct connection components—especially when they improve performance like these new replacement MSD Blaster ignition coils. They're designed with improved materials and windings to produce a stronger spark. This improved spark helps burn the fuel mixture more efficiently, resulting in smooth idle and heightened mid-range rpm power. Choose the OEM replacement designed for your year/make/model application.
( 628 )
$562.95
—
$727.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
