Availability
Showing In Stock Items. Show All 27 Items.
On Sale
Racepak's Vehicle Network (V-Net) is a "smart data" transfer network able to transmit multiple signals from sensors over a single cable. The key to the V-Net system is the modular connectors that attach each of the devices to the main cable. For a function or component to be monitored on the V-Net, the signal from that device must pass through a sensor and its module (essentially a miniature computer) that identifies and retrieves only the proper incoming signals and allows other signals to pass through. The sensor measures the input from the function or device (i.e. rpm, pressure, temperature, etc.), while the module converts the signal so it can be transmitted over the V-Net. Racepak analog pre-programmed V-Net modules with sensors are programmed to collect specific data and are ready for plug-and-play installation on the V-Net cable. Browse through the various types to determine which functions or components you want your V-Net system to monitor.
( 13 )
$259.95
—
$368.95
Racepak V-Net connector modules are used to convert the CAN data stream into a V-Net CAN bus data stream compatible with the Racepak V-Net system. This data is then available for use with the full range of Racepak V-net devices, including on-board displays, real-time telemetry, and data-logging applications. The Racepak V-Net connector modules provide setup capability to accommodate selection of scaling units, data-logging sample rates, and even custom sensor calibration.
( 2 )
$259.95
—
$399.95
AutoMeter CAN Bridge data modules are the ideal solution to streamline adding gauges or an InVision LCD dash to OBDII based engine and vehicle platforms (2008+). The intuitive CAN Bridge simply plugs into the diagnostic port and captures the existing sensor data and outputs up to six signals to drive a tachometer, speedometer, temperature, pressure, fuel level (0-90 ohm only), and volts on your vehicle. Quickly and easily setup your system to output the available parameters of your choice by utilizing the CAN Bridge data module's menu navigation buttons and OLED display. With this advanced CAN Bridge system from AutoMeter, you can now simplify your next instrumentation installation on your ride! Additional features: * Works with most OBD-II applications which is standardized across all OEMs starting in 2008 * Module includes OLED display and five push buttons to effortlessly navigate menus and program system for operation * Plug-and-play from OBDII to traditional round AutoMeter short sweep electric gauges, tachometers, electronic speedometers, and InVision LCD dashes * Six total channels available: tachometer, speedometer, fuel level (0-90 ohm only), temp, pressure, and volts * Simplifies instrumentation wiring and installation; no sensors to hookup, which means less wires to connect * Sensor data must be present on the data stream to function, otherwise a discrete sensor must be used
Not Yet Reviewed
$363.99
Racepak universal sensor modules provide an efficient and cost-effective way to add vehicle data sensors. Fully programmable, these modules feature rugged housings with securely mounted O-ring lids, four cable inputs with water-resistant cable strain reliefs, and four molded mounting pads for easier installation. Racepak USMs are designed to allow you to add Racepak or personally supplied sensors to their IQ3 logger dash. Multiple USM 4 sensor input modules can be used in your setup and will create a neat, professional look under your hood. Want to use sensors you already have to save some money? Racepak universal sensor modules are the way to go.
Not Yet Reviewed
$349.95
Racepak GPS V-Net modules allow you to add a GPS sensor to any non-GPS equipped V-Net data recorder. They utilize a standard V-Net tee connector and install into the Datalink II software, providing a speed channel for analytical, display, and odometer information.
Not Yet Reviewed
$429.95
Racepak un-programmed V-Net modules with sensors are customizable for a variety of applications. This makes them ideal whether replacing worn-out/damaged modules, or simply if you prefer your own programming for the V-Net system. The V-Net ID and sensor type parameters will not be pre-programmed on these modules. As with all V-Net modules connecting to the V-Net cable, they feature plug-and-play installation, and can be linked in any sequence. Repair or further customize your setup with Racepak un-programmed V-Net modules. Order the proper base pressure setting for your application.
Not Yet Reviewed
$329.95
Keep track of the movement of your shocks with one of these Racepak shock travel modules. Designed for use with Racepak shock travel sensors (sold separately), they do not require any programming and can accept inputs from up to four individual shock sensors. When used in conjunction with Racepak's shock travel kits, critical shock and chassis adjustments can now be made with confidence through the use of shock travel data.
Not Yet Reviewed
$329.95
Racepak V-Net modules work with the V-Net "smart data" transfer network to help you monitor a variety of functions and components on your vehicle. They feature plug-and-play installation on the V-Net cable for collecting the specific data you require. All connected modules are in series, so they can be installed and/or replaced in any sequence. Go ahead and build anything from a simple dash setup to a full-blown data acquisition system with Racepak V-Net modules. Browse through the various types to determine which functions or components you want your V-Net system to monitor.
( 1 )
$299.95
—
$329.95
On Sale
Racepak's Vehicle Network (V-Net) is a "smart data" transfer network able to transmit multiple signals from sensors over a single cable. The key to the V-Net system is the modular connectors that attach each of the devices to the main cable. For a function or component to be monitored on the V-Net, the signal from that device must pass through a sensor and its module (essentially a miniature computer) that identifies and retrieves only the proper incoming signals and allows other signals to pass through. The sensor measures the input from the function or component (i.e. rpm, pressure, temperature, etc.), while the module converts the signal so it can be transmitted over the V-Net. Racepak digital pre-programmed V-Net modules with sensors are programmed to collect specific data and are ready for plug-and-play installation on the V-Net cable. Browse through the various types to determine which functions or devices want your V-Net system to monitor.
Not Yet Reviewed
$349.95
—
$399.95
Racepak switch modules provide the ability to use existing switches in conjunction with a SmartWire module. Switches are connected to the spade connectors of the module, and switch data is routed to the SmartWire via a single cable. These modules allow your input for 16 remote switches. Adding a second switch module is quick and easy, through the use of a short jumper cable between the two modules. Racepak SmartWire switch modules are machined from billet aluminum and anodized black.
Not Yet Reviewed
$379.95
AEM 22-channel CAN sensor modules provide a way for users with carbureted vehicles to add an AEM CD digital dash display. They also let users with existing CAN-based devices add more channels to the display for viewing and/or data logging. These 22-channel modules convert analog, digital, and frequency inputs into an AEMnet CAN bus signal that can be transmitted to AEM's CD-5 carbon and CD-7 digital dashes. AEM Electronics 22-channel CAN sensor module includes: * Wiring harness with 36 in. flying leads and pre-wired CAN cable * IP65-rated enclosure is dust-tight and water-resistant * Daisy-chain two modules together for additional channels (modules sold individually) * Four dedicated 0-5 V analog inputs * Four temperature (thermistor) inputs * Four user-configurable inputs for 0-5 V, temp (including RTD) * One dedicated fuel level input (0 to 250 ohm range) * Six digital inputs, active low, protected to about 18 V, frequency, duty cycle or simple switch * One tach input, trigger when low, 12 V internal pull up * Two VR pair frequency inputs (crank, wheel, or driveshaft speeds) * Jumper selectable CAN bus speeds, 250k, 500k, 1M * Jumper selectable terminating resistor * Jumper selectable header length, 11 bit or 29 bit
Not Yet Reviewed
$413.95
Clearance
Racepak EFI V-Net Interface module cables are used to convert the serial data stream for an AEM EMS unit into a CAN bus data stream compatible with the RacePak V-Net System. Data from the module is then available for use with the full range of RacePak V-Net devices including on board displays, real time telemetry, and data logging applications.
Not Yet Reviewed
$389.95
$269.50
Computech DataMaxx Remote SD Modules are designed specifically for vehicles that are using magneto's. Magneto's disperse a wide range of electromagnetic noise and are necessary to get the SD circuit physically far away from that radius of noise corruption. The remote SD modules come with a 15 ft. cable and can also be used as a convenient way to mount them in an easy to reach location.
Not Yet Reviewed
$379.95
Computech DataMaxx EGT modules are designed to allow you to add up to four additional temperature sensors for exhaust gas temperature, cylinder head temperature, oil temperature, or water temperature to your DataMaxx main module. Their CAN-bus wiring only requires a single 4-conductor cable to connect the EGT module to the main module, simplifying installation.
Not Yet Reviewed
$349.95
On Sale
For your data recorder to be able to monitor an analog channel it must receive a signal that it can recognize. The Racepak Module PT2 convert the analog parameters to a standard 0-5 volt signal required by the recorder. The transducer module (combination sensor and signal conditioning modules) provides direct connection to the measured parameter, such as fuel or oil pressure. The signal conditioning module allows the connection of remote sensors, such as thermocouples or position sensors, to the data recorder.
Not Yet Reviewed
$399.95
On Sale
Racepak's Vehicle Network (V-Net) is a "smart data" transfer network able to transmit multiple signals from sensors over a single cable. The V-Net system uses modular connectors that attach each of the devices to the main cable. For a function or component to be monitored on the V-Net, the signal from that device must pass through a sensor and its module (essentially a miniature computer) that identifies and retrieves the proper incoming signal and allows other signals to pass through. The sensor measures the input from the function or device (i.e. rpm, pressure, temperature, etc.), while the module converts the signal so it can be transmitted over the V-Net. These pressure or temperature module/sensor combinations are the same as Racepak analog pre-programmed V-Net modules with sensors except that they have NOT been pre-programmed. Racepak analog programmable V-Net modules with sensors must be programmed using the Configuration File in Datalink software (not included).
Not Yet Reviewed
$329.95
Perfect your driving style with these FAST XFI 3-Axis accelerometer modules. These modules give you the ability to read and record positive, negative, and lateral g-forces in real time. This information can be very useful when setting up your suspension or perfecting your launches or cornering at the track. Get the most out of your street rod, hot rod, or track car with these FAST XFI 3-Axis accelerometer modules.
Not Yet Reviewed
$274.95
Racepak analog transducer boxes hold up to four drop-in pressure modules. They're perfect for Pro Stock and Pro Mod type race cars. The boxes allow you to run appropriate hose to your pressure source—and are available for naturally aspirated, nitrous oxide-injected, and supercharged applications.
Not Yet Reviewed
$369.95
—
$399.95
If your target is peak power, then AiM LCU-One Lambda controllers should be part of your engine-tuning plans. The precise mixture of air and fuel needs to be known for optimum performance. AiM Lambda controllers utilize proven wideband Bosch LSU 4.9 probes and can detect precise values from 0.65 to 1.6 to perfect your engine tuning. By offering configurability of Stoichiometric ratios, the LCU-Ones can be used on most gas, diesel, or alternative fuel engines. The controllers are available in three versions: CAN, analog, and CAN+analog. All of the data you need to hit peak efficiency--and keep it that way--is at your fingertips inside the AiM LCU-One Lambda controllers.
Not Yet Reviewed
$450.00
Racepak AF1 single channel air fuel sensor packages are designed to be utilized with any of Racepak's Vnet (canbus) series of data loggers. They are suitable for use with gasoline or alcohol, with calibration values available for either fuel types. The power supply requirement of 12 to 16 volts enables use with standard 12 volt or 16 volt high performance batteries. Racepak AF1 single channel air fuel sensor packages include: * Heat and water resistant controller with integrated Vnet module * Bosch LSU air/fuel sensor * Wiring harness * Installation instructions * Programmable 0-5 Volt analog output
Not Yet Reviewed
$499.95
FuelTech EGT-4 CAN conditioners are compatible with any Type K thermocouple (grounded junction or not). They feature a 4-channel signal conditioner with CAN bus communication for PowerFT ECUs that can be used to read EGTs, CHTs, oil, air, water or any other temperature using a Type K thermocouple. These units work as an input expander for PowerFT ECUs, freeing up four white input channels to be used for other purposes. With the possibility to use up to four EGT-4 modules in the same installation, as many as 16 different channels will be available for all sorts of data acquisition. PACKAGES AVAILABLE: * V8 / 2 units, harnesses and 8 sensors: -- with 2 harnesses -- 2 of each 42 in./36 in./30 in./24 in. Thermocouple sensors included -- Add second EGT-4 CAN unit * 6 cylinder / 2 units, harnesses and 6 sensors: -- with 2 harnesses -- 48 in./42 in./36 in./30 in./24 in./18 in. Thermocouple sensors included -- Add second EGT-4 CAN unit * 4 cylinder / harness and 4 sensors: -- with harness -- 42 in./36 in./30 in./24 in. Thermocouple sensors included * 4 rotor / harness and 4 sensors: -- with harness -- 4 of the 36 in. Thermocouple sensors included * 3 rotor / harness and 3 sensors: -- with harness -- 3 of the 36 in. Thermocouple sensors included * 2 rotor / harness and 2 sensors: -- with harness -- 2 of the 36 in. Thermocouple sensors included
Not Yet Reviewed
$399.00
Racepak V-Net 2-Axis G-Meters are sensor modules that add lateral and acceleration G-force measurement functionality to any Racepak V-Net display or logger dash. As with all V-Net modules connecting to the V-Net cable, they feature plug-and-play installation and can be linked in any sequence. Discover your optimal traction setup and get ahead of the curve with Racepak V-Net 2-Axis G-Meters.
Not Yet Reviewed
$329.95
Introducing the Holley EFI Single-Channel EGT kits! They keep you in-the-know about what's going on with your engine. Exhaust gas temperature data is critical information when your engine tune-up seems to be on the ragged edge. Knowing the exhaust temp can help you identify potential horsepower left on the table, or pinpoint any weak links in your max effort race engine. Holley offers these EFI Single-Channel EGT kits for non-Holley applications, as well as compatibility with HP Tuners, Dominator EFI, and Terminator X. Order the Holley EFI Single-Channel EGT kit to meet your application needs. Kit features, specs, and parts may include: * Single-Channel CANbus EGT controller module for quick and easy installation with Holley EFI—or Single-Channel Analog EGT controller with unterminated output wires for universal installations (please specify when placing order) * High-quality 1/4 in. stainless steel EGT weld bung * Robust 1/4 in. probe designed to withstand extreme cylinder pressures * Sensor (included) is designed to work with any engine combination, with an open reinforced tip for the fastest response rate and improved shielding
Not Yet Reviewed
$312.95
By installing Racepak wheelie bar load cells on both of your wheelie bars, you can create a record of how long and how hard the car was on the wheelie bars. In addition, you can determine if both wheelie bars are receiving equal loading and produce a visual record of how the car is reacting to a particular set-up. A V-Net module and pressure sensor (both sold separately) is attached to each load cell to monitor and graph the pressures generated in the load cells.
Not Yet Reviewed
$419.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
