Filters
Get access to even more vehicle data using HP Tuners Prolink+ cables to wire in up to two analog signals and one CAN bus signal simultaneously. Prolink+ cables are designed specifically for MPV12+ and MPV13. Specifications: * Two dedicated 0 to 5 V analog inputs * One CAN bus input--500kbps * 100Hz sampling rate * M8 connector to 5 wire harness * For MPVI2+ and MPVI3 interfaces Note: MPVI2+ interfaces must purchase Pro Feature Set to be able to use the PROLINK+ cable.
( 6 )
$49.99
AutoMeter OBD-II Signal Splitters provide remote mount connections for additional devices. These units are low-profile splitter/pass-throughs, and are ideal for AutoMeter products like AirDrive, DashLink, DashControl and SmartConnect instrumentation. They also provide additional, easy-to-access connection points for other onboard devices requiring access to the OBD-II data stream. Other features of AutoMeter OBD-II Signal Splitters are: * Connects to existing vehicle OBD-II port, providing two remote mount connections * 10 in. straight through leads with strain reliefs between 16-pin male and female connectors compatible with J1962 OBD-II Standards * Please note: device and vehicle compatibility may vary. Signal splitter designed to maintain OBD-II data signal integrity across two remote connection points, but does not correct for data bus termination, traffic conflicts, or compatibility of attached devices.
( 11 )
$43.99
The Edge accessory system (EAS) was created with future expandability in mind. The architecture of the EAS allows users to connect multiple accessories daisy-chain style to the evolution CS or CTS. This means Edge can create optional accessories that can be added to the products by the owner at any time. An optional exhaust gas temperature (EGT) probe is one example of an optional accessory that will be offered by Edge. These replacement (or add-on) EGT leads are computer chip programmer input cables. Get the most from your specific accessory system with lead probe cables.
( 2 )
$40.95
Take advantage of your BRP vehicle's full potential with an HP Tuners OBDII adapter cable. Plug the gray insert directly into your BRP's diagnostic port and the black OBDII-end into your MPVI2, MPVI2+, or MPVI3 interface for full functionality. This OBDII adapter cable is required for tuning any supported BRP vehicles, including Can-Am and Sea-Doo.
Not Yet Reviewed
$49.99
Want to maximize the performance of your current HP Tuners setup? HP Tuners offer computer programmer accessories, from USB cables to OBD-2 cables, EIO plugs, and more. These quality hardware components can be used as replacements for worn or misplaced originals, or to upgrade your existing setup.
( 14 )
$34.99
—
$49.99
Looking for a safe, simple way to mount your FiTech color touch screen tuner? FiTech's Premium magnetic handheld mounts provide an easy and effective way to secure the touch screen controller. They allow you to mount the touch screen nearly anywhere in your car with a sturdy, adjustable stand equipped with two extremely strong magnets to firmly secure the handheld through vibrations, shocks, bumps, and even during spirited track laps! FiTech Premium magnetic handheld mounts are supplied with the injection molded stand, a mounting disc to apply to the dash or console, and a mounting plate designed specifically for the FiTech color touch screen handheld monitor. You can position the tuner where you can easily view the engine parameters and tuning of your FiTech EFI system.
( 2 )
$51.00
Edge OBDII Pass-Through Signal Splitters allow two products to be simultaneously plugged into the OBDII port—such as an Edge Insight monitor unit and another product, including (but not limited to) power running boards or other potential OBDII powered products. These new OBDII splitters are fully populated with a 16-pin pass-through, pinned connector. Products may vary on what can be running at the same time. Not recommend for use with two monitors or tuners plugged in at the same time.
Not Yet Reviewed
$54.09
Edge cast aluminum pillar display mounts offer a more permanent and vehicle-specific mount for their CTS3 based devices. The mounts are specifically engineered for an OEM look and fitment to place your CTS3 monitor in the perfect viewing position without obstructing your view of the road. They provide a sturdy mounting location to replace Edge's standard suction cup style mounts. Coated in a sleek matte black finish, they offer a clean look in any interior and can be painted for a custom finish, if desired. Order the model recommended for your vehicle. Additional details: * Cast aluminum for rigidity and solid mounting * Custom molded for vehicle specific fitment * Paintable finish for complete end user customization * No drilling required, mounts using existing A-Pillar grab handle location * Locates monitor in optimum viewing position * Hardware and dual T-slot mount included * Works with all CTS3 devices, including Insight, Evolution, and Juice * Also works with older CTS2 and CS2 style monitors * May work with other aftermarket mounts that use similar uni-ball construction
( 3 )
$54.29
—
$56.32
Edge OBDII to HDMI cables are direct replacement components for connecting your Edge CS2 or CTS2 comprehensive gauge display (sold separately) to your vehicle's OBDII port. These connector cables are made to last through your tuning needs.
( 1 )
$21.47
Bully Dog replacement pyrometer probes are designed to read exhaust gas temperatures consistently and accurately. They feature a thread-in style port and connect easily to your Bully Dog pyrometer gauge.
Not Yet Reviewed
$50.99
Keep an eye on your X4 and the road ahead with SCT suction cup mounts for your windshield. These mounts securely hold your programmer with an industrial-strength suction cup, allowing you to safely monitor critical system data without blocking your view. You don't want to hold your X4 while driving, and often there's no passenger to assist you. The solution is quick, easy, and economical--SCT suction cup mounts.
( 6 )
$22.99
Banks Power universal OBD II splitters allow you to connect two devices to the OBDII port. The plug is a right angle for minimal interference. Notes: * For use with Banks devices and retractable steps * Not intended for use with Banks devices AND third-party OBD monitors * Most ECMs will only communicate with one diagnostic device at a time. Using a splitter will result in the vehicle's ECM having to choose between devices. One of your devices will not operate properly.
Not Yet Reviewed
$30.00
Painless VATS computer chips allow you to bypass the factory programming, making the wiring in your engine swap a snap. Since 1989, most GM fuel injection systems have incorporated a Vehicle Anti-Theft System (VATS) programmed into the stock EPROM or PCM. This means the engine will not run if it is transplanted into a vehicle without the original vehicle steering column and decoder module. If you have one of these engines and your computer has the factory programming, you need Painless VATS computer chips to make your job trouble-free.
( 11 )
$49.99
—
$52.99
Bully Dog RAM suction cup mounting kits position your performance device for the best in-use experience possible. Featuring a strong and effective suction cup, stout arms, and a custom T-slot adapter, each of these kits is specifically designed to work with your GT or WatchDog unit. Brace your device on the proper pedestals for secure, safe usage--Bully Dog RAM suction cup mounting kits.
( 1 )
$32.79
SCT single program and 5-program, 4-bank custom eliminator switch chips are tuned for specific car and truck applications. Order the module recommended for your vehicle. Features include: * Can be custom tuned by one of SCT's Custom Tuning dealers worldwide * Installation only takes 10-15 minutes with standard hand tools * Perfect for nitrous or towing applications. Switch tunes on the fly or at the track * Mountable switch panel for easy access to switching tune files * Built-in anti-theft selection that disables PCM and prevents the vehicle from starting NOTE: This product does not support any changes to your vehicle's emission system.
( 2 )
$33.79
SCT magnetic windshield mounts feature heavy-duty suction cup bases that securely adhere to windshield glass and four ultra-strong neodymium magnets that ensure your device stays front-and-center--no matter what terrain you travel. Each of these SCT BDX window mounts include a 90 degree HDMI elbow that not only eliminates potential strain on your port, but also ensures your wires stay tucked perfectly for the cleanest setup around.
Not Yet Reviewed
$25.79
SCT Livewire TS+ window mounts are designed specifically to help utilize all of the innovative features of your Livewire TS+ tuner/programmer. Use these mounts to attach your module to the vehicle window, so you can easily and safely read the display at a glance. You can affix the Livewire TS+ vertically or landscape-style for the perfect viewing angle. Keep your real-time gauges and data monitoring safely visible with SCT Livewire TS+ window mounts.
Not Yet Reviewed
$25.79
Open up the power of your diesel engine using Bully Dog GT diesel unlock cables. They feature pre-terminated connections and hook up directly to your Bully Dog GT diesel tuner.
( 2 )
$41.99
Gale Banks is an innovative engineer in the world of diesel performance, and his company is a leader in the aftermarket industry. Banks Power interconnect cables allow your vehicle to communicate with their various parts to ensure the best outcome. These cables allow Banks tuners and/or SpeedBrakes to connect with the vehicle's OBD-II port in order for the tuner, the vehicle, and the iQ, if so equipped, to communicate with each other. Banks Power interconnect cables are designed to communicate across all of their platforms to obtain maximum performance and bring your vehicle to life.
Not Yet Reviewed
$23.00
—
$38.00
DiabloSport inTune replacement OBD II cables are service parts for the DiabloSport inTune i2, I-1000, and I-1000-DCX "iPod" style connectors. This cable works for all Tune i2 products, but should only be used on inTune I-1000 and I-1000DCX with a build date after March 2013. These diagnostic link connector cables transmit data to or from your automotive performance programmer. * To check your inTune or inTune DCS build date, look for the white date code sticker on the product box. Using this cable with units made before March 2013 could cause damage to the OBD-II connection on your inTune device.
Not Yet Reviewed
$53.05
SCT Livewire TS+ pod adapters allow you to make use of any existing 2 1/16 in. gauge pods. Designed specifically for Livewire TS+ gauge tuners, these adapters make convenient A-pillar mounting a snap. The T-slot and optional ball mount design ensure a quick and easy installation of your tuner. Procure a clean and secure mounting location with SCT Livewire TS+ pod adapters.
Not Yet Reviewed
$22.79
HalTech's DTM-4 power supply cables allow +12 V to be sourced from a +12 V switched supply within the vehicle wiring harness for powering up the HalTech CAN wideband. The DTM-4 power supply cable was included in the WB1 and WB2 kits and conveniently offered separately.
Not Yet Reviewed
$47.00
ACDelco computer mounting brackets are GM-recommended replacement parts. These original equipment brackets deliver the ideal fit and function to restore support of your computer. Keep your computer mounted securely; order the ACDelco replacement brackets designed for your application. .
( 2 )
$20.99
—
$43.99
Denali Electronics DataDim dual-intensity controllers enable Denali driving lights to switch between half and full intensity with your vehicle's original high-beam switch. Simply plug this controller into the harness end included with their LED light kits to enable dual-intensity functionality. All Denali 2.0 light pods are equipped with a dedicated 3rd-wire dimming circuit. It allows the use of an external signal for reliably controlling intensity of the LED chip at the source. Order a Denali DataDim dual-intensity controller for driving light harness to set the intensity level for all your vehicle's lights with your high-beam switch. In the box: * DataDim dual-intensity controller * Dual-intensity trigger wire
( 1 )
$54.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
