Availability
Clevite's M-Series main bearings are special-purpose items. They have a nominal 0.006 in. thick babbit layer on hardened-steel backings and are intended for engines that have severe crankshaft deflections. They have enlarged chamfers and, for some applications, both the oil holes and the oil grooves are enlarged.
( 1 )
$130.99
Clevite P-Series main bearings are the oldest members of the Clevite 77 bearing family and are intended for high-revving engines. To compensate for the high-load factors and distortion in these engines, these bearings have higher eccentricity and a high crush factor. P-Series bearings are constructed of tri-metal cast copper lead. They have a steel back for support, a cast copper lead lining to withstand the loads of engine operation, and an electroplated babbit overlay on the running surface to provide searing surface qualities. In addition, the oil grooves on most applications extend all the way around both halves for better oiling. Clevite P-Series main bearings are an ideal design, producing a degree of conformability, embedability, slipperiness, and fatigue resistance, not found in original equipment and competitive bimetal bearings.
( 252 )
$11.99
—
$372.99
ACL Performance offers Race Series rod bearing sets for a wide range of vehicles. These high performance tri-metal engine bearings are designed to withstand higher RPM conditions. They feature a high-strength overlay plate with reduced thickness for improved fatigue properties. Select the crankshaft undersize and quantity recommended for your year/make and engine application. Additional details: * Hardened steel backs on all rod bearings to improve the support of the bearing lining and assist with bearing retention in the housing. * Increased crush for improved bearing retention * Elimination of flash plating on the back of the bearings to improve heat transfer through the bearings and to maximize the grip between the bearings and its housing * Increased eccentricity to compensate for bore distortion at high RPM and to assist in the formation of hydrodynamic oil films * 3/4 in. grooved main bearings to optimize bearing load carrying surface area and oil flow to the conrod bearings * Tight consistent wall tolerances to help you maintain consistent clearances * Enlarged ID chamfers on bearing edges (where required) to accommodate large fillet radius on performance crankshafts
( 8 )
$19.50
—
$264.99
Sealed Power engine products are a complete system of application-engineered replacement components, including pistons, piston rings, engine bearings, camshafts, oil pumps, timing components and valvetrain products. Sealed Power connecting rod bearings are available with different linings to meet every engine's needs. They're made using either tri-metal or aluminum bi-metal construction for the utmost in performance and durability for all stock rebuilds and mild performance applications. Tri-metal alloys feature a steel base coated with a sintered layer of copper-lead alloy, followed by layers of electro-plated nickel and babbit to produce the ultimate bearings. Bi-metal aluminum types carry all of the same features without the babbit, as specified by many of today's top engine builders. Sealed Power bearings are available for a multitude of engines in sizes ranging from standard to 0.060 in. oversized.
( 8 )
$8.99
—
$215.99
ACL Performance offers cam bearing sets for a wide range of vehicles from 1955 and up. The high performance tri-metal engine bearings are designed to withstand higher RPM conditions. Each direct-fit replacement bearing features a high-strength overlay plate with reduced thickness for improved fatigue properties. Oder the set recommended for your year/make and engine application. Additional details: *Hardened steel backs on all rod bearings to improve the support of the bearing lining and assist with bearing retention in the housing. * Increased crush for improved bearing retention * Elimination of flash plating on the back of the bearings to improve heat transfer through the bearings and to maximize the grip between the bearings and its housing * Increased eccentricity to compensate for bore distortion at high rpm and to assist in the formation of hydrodynamic oil film * 3/4 in. grooved main bearings GROOVED MAIN BEARINGS to optimize bearing load carrying surface area and oil flow to the conrod bearings * Tight consistent wall tolerances to help you maintain consistent clearances * Enlarged ID chamfers on bearing edges where required to accommodate large fillet radius on performance crankshafts
( 1 )
$26.79
—
$95.99
King AM-Series main bearing spacers are standard, aluminum-based parts designed for passenger cars with low-to-medium engine loads. They're sold as spacer sets for specific swaps, like adapting a Chevy 350 crankshaft into a 400 engine block, providing reliable, cost-effective, environmentally-friendly performance with excellent embeddability to protect crankshafts. Key features: * Material: Standard aluminum-based (Alecular) alloy, softest in King's line, ideal for everyday driving * Performance: Good embeddability to absorb small particles, preventing crank journal scoring, and durable for typical use * High-precision manufacturing for consistent thickness, ensuring uniform load distribution
( 1 )
$116.99
Manley offers Clevite main bearings to deliver the high performance you need for your high-revving engines. To compensate for the high-load factors and distortion in these engines, these bearings have higher eccentricity and a high crush factor. Constructed of tri-metal cast copper lead, they have a steel back for support, a cast copper lead lining to withstand the loads of engine operation, an electroplated babbit overlay on the running surface to provide searing surface qualities, and oil grooves for better oiling. For your Manley rotating assemblies, order Clevite bearings for conformability, embeddability, and fatigue resistance.
Not Yet Reviewed
$81.52
—
$125.28
Pro-X Racing Parts offers a complete line of piston pin bearings for the dirt bike, ATV, PWC, and 50cc/scooter segment. The pistons pin bearings are manufactured by the leading Japanese OEM factories, and all piston pin bearings are designed and developed to OEM specifications as direct-fit, cost-effective replacements. Choose the Pro-X piston pin bearings designed for your powersports machine.
Not Yet Reviewed
$10.99
—
$19.99
King TFC-Series engine main bearings feature a special factory applied nano-composite polymer coating—with no added thickness! The Top Fuel Line represents the culmination of the innovative and goal oriented research and production from King Engine bearings House. These bearings are available for a wide range of vehicles, especially year/make and engine applications from the 1960s and '70s. Additional details: TOP FUEL BEARINGS with K-40 POLYMER COATING: This coating composition was specially designed for engines experiencing continuous metal-to-metal contact, which is characteristic of the extreme loading and conditions found in various categories of drag racing. K-40 is used for Top Fuel, Funny Car, Pro Mod and similar applications—where bearings are required to resist metal-to-metal contact and deformation. Extreme loads cause the oil film to break down, allowing contact between the bearing and crankshaft surfaces. Maintaining low friction, even during the conditions of metal-to-metal contact, is crucial to the life of any engine bearing. King TFC bearings are designed to withstand the loading generated from 10,000 hp Top Fuel engines. TFC winning attributes: * HIGH STREGTH STEEL: able to withstand extreme loads * SPECIAL DUCTILE BRONZE LINING: will not crack under significant plastic deformation caused by high power engine (10,000 hp) * EXTRA THICK BABBIT LINING: strengthened by copper, excellent conformability * K-40 POLYMER LAYER: provides excellent anti-friction and anti-seizure properties during metal-to-metal contact
( 1 )
$197.99
—
$382.99
All Balls Racing wheel and carrier bearing seal kits are hands-down the most complete line of bearing seal kits on the market! They are available in a wide variety of powersports applications, from ATV and off-road to street bikes. These All Balls Racing wheel and carrier bearing seal kits have premium high-speed bearings that feature low-drag, double-lip seals on both sides to provide superior exclusion of water and dirt and improved grease retention. High performance Chevron SRI-II grease features special rust inhibitors for the most demanding applications. Type TC nitrile elastomer wheel seals are specifically designed to keep out water and dirt. Their rubber coated outside diameter helps to create an optimum seal at the hub.
( 20 )
$63.61
Need bearings? See the specialists at King. Their CA-Series rod bearings are a bi-metal silicon aluminum material offering high fatigue strength and a superior temperature threshold. When it comes to bearings, there is only one King Engine Bearings.
( 4 )
$8.99
—
$10.99
King SI-Series rod bearings are recommended for OE applications. They're designed for aftermarket gasoline or diesel engine rebuilding and performance engines with OE crankshafts. These direct replacements have an improved finish for reducing microscopic ferrite peaks on improperly ground or polished nodular cast iron crankshafts. King SI-Series rod bearings also feature improved oil clearance to reduce wear and increase engine life—which, in turn, lessens operating noise, vibration, and excess oil flow. Hundreds of sets are available; order the bearings recommended for your vehicle.
( 92 )
$8.99
King HP-Series rod bearings were developed mainly for drag race applications needing a material harder than the Babbitt top layer. These applications demanded a structure that could withstand high loads for short durations and still offer higher embeddability and compatibility. In response, King developed the HP-Series, featuring the Alecular metal structure. The HP-Series is also suited for many performance applications with nodular cast iron crankshafts, such as street, strip, and some levels of Circle Track racing. Order the set recommended for your vehicle. HP-Series bearings are particularly suitable for the following cases: * When a tri-metal bearing's Babbitt overlay extrudes over the sides, migrates to one end, or is physically removed by the crankshaft * When the intermediate layer of a tri-metal bearing is exposed, damaging the crank journal and requiring expensive grinding or replacement * When contaminants enter the oil stream, scratching and damaging the crankshaft journals
( 36 )
$66.99
—
$136.99
Give your engine the winning edge with King XP-Series coated main bearings. Built off the revolutionary XP-Series tri-metal construction, King's factory-applied pMaxKote™ nano-composite coating takes protection to the next level without adding any additional thickness! Order the replacement main bearings designed for fitment with your engine. pMaxKote™ provides: * Superior seizure resistance * Superior cavitation resistance * Superior wear resistance * Superior protection against oil starvation
( 7 )
$67.99
—
$338.99
King HP-Series main bearings are recommended for street and strip performance applications. They're designed for blown, turbocharged, NOS, and alcohol-fueled engines using aftermarket crankshafts. These main bearings have greater eccentricity for superior oiling at high rpm, and a chamfered surface for large radii crankshafts. HP-Series bearings also feature large, chamfered oil holes—and are available in 1/2 grooving for improved oiling to withstand high-rpm applications. Order the bearings designed for fitment with your specific engine.
( 48 )
$66.99
—
$172.99
King HP-Series cam bearings are precision-machined to tight tolerances to control installed oil clearances, reducing operating bearing pressure. These cam bearings are constructed from seamless steel tubing with a thin layer of lead based babbit material to reduce microscopic deflections. The babbit is quickly cooled in the casting process to achieve a very fine grain structure, doubling tensile strength, therefore, the HP-Series offers much more fatigue strength than conventional bearings, and can withstand racing spring loads, while maintaining the excellent surface characteristics of babbit. King also offers HP-Series bearings with a fluoropolymer coating. Bearings with this coating retain engine oil on the surface, even under extreme heat and pressure—a great advantage! Plus, being a lubricant, it provides backup during start-up and in the event of momentary oil starvation. Use track-tough King HP-Series cam bearings in your engine—and experience the difference.
( 13 )
$59.99
—
$256.99
Give your engine the winning edge with King XP-Series coated rod bearings. Built off the revolutionary XP-Series tri-metal construction, King's factory-applied pMaxKote nano-composite coating takes protection to the next level without adding any additional thickness! These high performance race bearing sets are available for fitment on a wide range of specific vehicle applications. pMaxKote provides: * Superior seizure resistance * Superior cavitation resistance * Superior wear resistance * Superior protection against oil starvation
( 10 )
$37.99
—
$406.99
Built with enhanced tri-metal, King XP-Series main bearings have a layered copper lead construction, with a nickel plate barrier and lead/tin/copper Babbitt overlay over a steel backing--in an adhesion process that provides superior stability and durability. King's advanced control measures hit a bull's-eye, maintaining wall thickness tolerances far tighter than their competitors: an amazing +/- .0001 in. The XP-Series main bearings are narrowed for large radii crankshafts and feature enlarged, chamfered oil holes with full, 3/4 in., or 1/2 in. grooving for improved oiling. They deliver consistent and reliable performance with a high-load capacity. These race-only Xtreme Performance (XP-Series) Tri-Lecular main bearings are proven track-tough to handle the ground-shaking power of your race engine. Hundreds of sets are available; order the bearings recommended for your vehicle.
( 43 )
$232.99
King XPG-Series coated rod bearings feature a unique lug design that eliminates the conventional lug recess, so no oil escapes and full oil pressure is maintained. With enhanced tri-metal copper/lead construction and nickel barrier, plus SecureBond adhesion, King XPG-Series coated rod bearings have a 20 percent higher load capacity—and better resist surface fatigue. They also feature King's factory-applied pMaxKote nano-composite coating that takes protection to the next level without adding any additional thickness! These replacement sets are available in different sizes for a variety of applications. For superior engine components, choose King.
Not Yet Reviewed
$40.99
—
$81.99
King XPG-Series coated main bearings feature a unique lug design that eliminates the conventional lug recess—so no oil escapes and full oil pressure is maintained. With enhanced tri-metal copper/lead construction and nickel barrier, plus SecureBond adhesion, these bearings have a 20 percent higher load capacity and will better resist surface fatigue. They also feature King's factory-applied pMaxKote nano-composite coating that takes protection to the next level without adding any additional thickness! XPG-Series sets are available for a variety of vehicle and engine applications.
Not Yet Reviewed
$153.99
Clevite camshaft bearings are manufactured to meet or exceed OEM parts when it comes to strength and durability. They will help to give your motor extra life, and their quality construction and superior materials will help to protect your vital engine parts from the harmful effects of friction. With thousands of applications, you're sure to find the bearings you need for your motor.
( 186 )
$37.99
King AM-Series rod bearings are recommended for street or marine applications. They have superior embeddability, which provides greater macro-particle and reduces scratching of the crank journals and tearing or weakening of the Babbitt overlays. The direct replacements feature tolerance control up to +/- .0001—and they're lead-free, making them environmentally friendly and user-safe. Order the King AM-Series rod bearings in the application designed for proper fitment with your vehicle.
( 29 )
$14.99
—
$16.99
Dura-Bond took their high performance bearings and coated them with a secondary dry film lubricant for added protection against oil starvation.
( 45 )
$68.99
Clevite M-Series rod bearings are special-purpose items. They have a nominal 0.006 in. thick babbit layer on hardened-steel backings--and are intended for engines that have severe crankshaft deflections. These rod bearings have enlarged chamfers, as well as dowel holes in the lower halves to accommodate the dowels used on aluminum rods. For some applications, both the oil holes and the oil grooves are enlarged.
Not Yet Reviewed
$19.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
