Availability
Showing In Stock Items. Show All 52 Items.
P-Series rod bearings are the oldest members of the Clevite 77 performance bearing family. They're intended for high-revving engines, especially those where the high rpm cause the rod bores to narrow. To compensate for this distortion, these direct replacements have higher eccentricity and a high crush factor. Clevite P-Series rod bearings are built on hardened-steel backings with extra-thin overlays, and their lower sections have dowel holes for use with aluminum rods, and there are extra-clearance variations available with an additional 0.001 in. of clearance. Order the model designed for your vehicle and engine application.
( 285 )
$35.99
—
$49.99
King SI-Series main bearings are recommended for OE applications. These replacement bearings are designed for aftermarket gasoline or diesel engine rebuilding—and performance engines with factory crankshafts. The bearings have an improved crankshaft finish for reducing microscopic ferrite peaks on improperly ground or polished nodular cast iron crankshafts. King SI-Series main bearings feature improved oil clearance to reduce wear and increase engine life, which in turn reduces operating noise, vibration, and excess oil flow. Order the bearing set designed for fitment on your make and model.
( 79 )
$22.99
—
$53.99
Sealed Power A-Series rod bearings can actually polish the journals on your crankshaft. That's because there's a small percentage of silicon mixed in with the aluminum and tin that make up the bearing-surface alloy. The silicon is there for wear resistance, but its toughness actually smoothes the journals of a crank with a surface that hasn't been optimized! This special surface alloy is laid over a high-strength 1010 steel backing and delivers improved seizure and corrosion resistance, as well as better wall variance control. It also helps to minimize debris embedding, which can score the crank's surface. Order the replacement bearings designed for your vehicle make and engine application.
( 33 )
$28.99
—
$34.99
Clevite coated H-Series rod bearings were developed primarily for NASCAR racing, but are also well suited to other types of competition engines. They're especially good for engines that run at medium-to-high revs. They have hardened-steel backings with thin overlays and a high crush factor, plus a medium level of eccentricity. H-Series bearings feature Clevite's exclusive TriArmor coating, the industry's only moly/graphite treatment. The sophisticated blend, in a low-friction PTFE polymer base, offers extraordinary protection and lubricity. They also have enlarged chamfers at the sides for greater crank-fillet clearance and are made without flash plating for better seating. The Clevite coated H-Series rod bearings are available with various under-sizes, including 0.001 in. of clearance for polished journals.
( 10 )
$25.99
These Summit Racing™ main bearings are just what you need to freshen up your engine. Why? They use silicon aluminum bi-metal construction. Silicon aluminum is the choice for many of today's engine manufacturers because of its high fatigue strength and superior temperature threshold. Bearing wear is dramatically reduced and the fatigue strength is greatly improved.
( 96 )
$56.99
For stock replacement rod bearings with perfect fit and function, choose Chevrolet Performance. Available for your LS-Series and big block engines, these rod bearings offer worry-free performance for your big horsepower. When you need originals, go to the original--Chevrolet Performance connecting rod bearings.
Not Yet Reviewed
$21.99
—
$37.99
Federal Mogul CP-Series rod bearings feature classic tri-metal construction and are a good choice for either street or moderate competition use. They have rugged 1010 steel backings, covered by Federal Mogul's H-24 copper-lead alloy. On top of this is a nickel barrier, followed by the tri-metal (lead-tin-copper) overplate that gives these bearings their strength and fatigue resistance. The bearings are then entirely covered with a flash coating of tin. Order the set designed for use with your make/model and engine application.
( 115 )
$28.99
—
$39.99
Economical Dura-Bond standard cam bearings feature round babbit construction for low friction, outstanding conformability, and added embeddability.
( 94 )
$39.99
More and more manufacturers have shifted to aluminum bearings in their OE engines and Clevite AL-Series rod bearings are designed to be the highest-quality replacement bearings in the industry. They carry on the tradition and reputation that Clevite has built throughout the course of time. AL Series engine bearings feature a 100 percent lead-free aluminum silicon bi-metal material, which includes 60 percent more silicon than the leading competitor's bi-metal material for better conditioning of journal surfaces. These bi-metal bearings also offer greater wear resistance than the leading competitor's bi-metal material, as well as greater seizure resistance. Clevite AL-Series bearings feature 100 percent bored inside diameters for precision and surface characteristics and, where appropriate, straight-shell main bearings utilizing an "umbrella" groove that allows for superior oil control and improved pressure.
( 26 )
$29.99
—
$35.99
For high load applications, King SM-Series rod bearings contain the strongest aluminum-based material offered by King. The alloy is strengthened by the addition of manganese and chromium. King SM-Series connecting rod bearings feature a traditional steel-backing, plus an aluminum bonding layer and the aluminum bearing alloy. These replacement sets are available for a variety of vehicle applications.
( 1 )
$22.99
—
$48.99
Today's engines operate under very demanding conditions. Sealed Power has responded to this challenge with their babbit high performance cam bearings. They feature high embedability and conformability and a special "sacrificial" design that enables the bearing surface to deform under extreme loads, preventing any wear and damage to the camshaft.
( 115 )
$33.99
—
$39.79
King SV-Series rod bearings provide movement with minimal power loss. Connecting rod bearings provide rotating motion of the crank pin within the connecting rod, which transmits cycling loads applied to the piston, and King SV-Series will provide this function well to handle your extreme load engines. These King SV-Series connecting rod bearings are copper-based and lead-free, offering great wear resistance, as well as load capacity.
( 3 )
$23.99
—
$28.99
ACL Performance offers Race Series rod bearing sets for a wide range of vehicles. These high performance tri-metal engine bearings are designed to withstand higher RPM conditions. They feature a high-strength overlay plate with reduced thickness for improved fatigue properties. Select the crankshaft undersize and quantity recommended for your year/make and engine application. Additional details: * Hardened steel backs on all rod bearings to improve the support of the bearing lining and assist with bearing retention in the housing. * Increased crush for improved bearing retention * Elimination of flash plating on the back of the bearings to improve heat transfer through the bearings and to maximize the grip between the bearings and its housing * Increased eccentricity to compensate for bore distortion at high RPM and to assist in the formation of hydrodynamic oil films * 3/4 in. grooved main bearings to optimize bearing load carrying surface area and oil flow to the conrod bearings * Tight consistent wall tolerances to help you maintain consistent clearances * Enlarged ID chamfers on bearing edges (where required) to accommodate large fillet radius on performance crankshafts
( 7 )
$44.99
—
$45.99
Give your engine the winning edge with King XP-Series coated rod bearings. Built off the revolutionary XP-Series tri-metal construction, King's factory-applied pMaxKote nano-composite coating takes protection to the next level without adding any additional thickness! These high performance race bearing sets are available for fitment on a wide range of specific vehicle applications. pMaxKote provides: * Superior seizure resistance * Superior cavitation resistance * Superior wear resistance * Superior protection against oil starvation
( 10 )
$38.99
—
$46.99
King SI-Series rod bearings are recommended for OE applications. They're designed for aftermarket gasoline or diesel engine rebuilding and performance engines with OE crankshafts. These direct replacements have an improved finish for reducing microscopic ferrite peaks on improperly ground or polished nodular cast iron crankshafts. King SI-Series rod bearings also feature improved oil clearance to reduce wear and increase engine life—which, in turn, lessens operating noise, vibration, and excess oil flow. Hundreds of sets are available; order the bearings recommended for your vehicle.
( 92 )
$20.99
—
$31.99
Chevrolet Performance main bearings are OEM replacements made to stand up to the demanding operating conditions, high heat, and strenuous loads of today's engines. These main bearings are constructed from high-quality materials for exceptional fatigue strength and wear rates. You can depend on Chevrolet Performance for high-quality, reliable replacement parts to keep your engine running strong.
( 1 )
$48.99
King MC-Series engine main bearings are available for a wide range of vehicles, including models from Chevrolet, GMC, Ford, Cadillac, Hummer, Isuzu, Pontiac, and Saab. These stock replacements are machined from bi-metal silicon aluminum and sold in sets of 5 or 6, depending on your application. Main bearings hold the crankshaft in place and allow it to rotate within the engine block.
Not Yet Reviewed
$53.60
King XP-Series rod bearings feature advanced metallurgical and geometric technologies that meet extreme performance loads. They were developed for all performance applications that use forged steel aftermarket crankshafts and produce high loads for extended periods. King focuses on one product—bearings—and nothing else. Their innovative race-only Xtreme Performance Max Black Tri-Metal rod bearings have a 24 percent stronger overlay and 17 percent more fatigue strength by using a micro process called SecureBond. Built with enhanced tri-metal, King XP-Series rod bearings layer copper-lead construction with a nickel plate barrier and a lead/tin/copper Babbitt overlay over a steel backing in an adhesion process that provides superior stability and durability. King's advanced control measures hit a bull's-eye, maintaining wall thickness tolerances far tighter than their competitors—at an amazing +/- .0001 in.! XP-Series rod bearings are narrowed on the crank cheek side with increased crush height for improved bearing-to-bore contact, heat transfer, and reduced spin potential in high-rpm applications.
( 66 )
$29.99
—
$50.99
ACDelco GM Genuine Parts camshaft bearings are true OE parts installed during production of or validated by General Motors for GM applications. They're designed, engineered, and tested to rigorous standards to ensure the correct fit and function in your vehicle. These bearings are machined from steel-backed bronze alloy and are available in a variety of diameters. For a stress-free install and predictable performance, service your vehicle with direct-fit replacement parts from ACDelco.
( 2 )
$32.99
King Engine BB-Series cam bearings are recommended for OE rebuild applications. These cam bearings are babbitt on steel, and are precision machined and then micro-finished to offer long-lasting durability. Save yourself a costly rebuild with King Engine BB-Series cam bearings—stock replacements that been proven, time and time again, to get the job done.
( 14 )
$22.99
Considering an LS engine swap? Advance Adapters crankshaft bushing spacers will help to make the fit a perfect match. Simply bolting the old-style converter to your LS engine won't work without the proper spacer. These steel accessories create the required distance, so the nose of the torque converter fits with the crank. Keep your crankshaft and add one of these Advanced Adapters bushing spacers.
( 1 )
$28.39
Considering an LS engine swap? TCI pilot extension adapters will help to make the fit a perfect match. Simply bolting the old-style converter to your LS engine will not work without the proper spacer. TCI spacers will create the required distance, so the nose of the torque converter fits properly with the crankshaft.
Not Yet Reviewed
$52.95
ACDelco offers engine crankshaft thrust washer bearings for a broad range of cars, trucks, vans, and SUVs. These performance-grade replacements are designed, engineered, and tested to rigorous standards—backed by General Motors. They are OE parts validated specifically for Chevrolet, Buick, GMC, Hummer, and Pontiac vehicles. Order the thrust washers recommended for your application.
( 1 )
$44.99
Today's engines operate under very demanding conditions. When these Sealed Power main bearing sets are used in performance applications, all components are pushed to their limits—and many must be changed to meet these special demands. Federal Mogul, a longtime supplier to both OEM and the aftermarket, has responded to this challenge with its tri-metal, copper-lead, high performance main bearing sets. They're tested in the lab and proven on the track. The bearings are available for various crankshaft undersizes, for direct replacement or performance usage on a wide range of specific applications.
( 97 )
$29.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
