Availability
Showing In Stock Items. Show All 405 Items.
P-Series rod bearings are the oldest members of the Clevite 77 performance bearing family. They're intended for high-revving engines, especially those where the high rpm cause the rod bores to narrow. To compensate for this distortion, these direct replacements have higher eccentricity and a high crush factor. Clevite P-Series rod bearings are built on hardened-steel backings with extra-thin overlays, and their lower sections have dowel holes for use with aluminum rods, and there are extra-clearance variations available with an additional 0.001 in. of clearance. Order the model designed for your vehicle and engine application.
( 285 )
$20.99
—
$57.99
Clevite P-Series main bearings are the oldest members of the Clevite 77 bearing family and are intended for high-revving engines. To compensate for the high-load factors and distortion in these engines, these bearings have higher eccentricity and a high crush factor. P-Series bearings are constructed of tri-metal cast copper lead. They have a steel back for support, a cast copper lead lining to withstand the loads of engine operation, and an electroplated babbit overlay on the running surface to provide searing surface qualities. In addition, the oil grooves on most applications extend all the way around both halves for better oiling. Clevite P-Series main bearings are an ideal design, producing a degree of conformability, embedability, slipperiness, and fatigue resistance, not found in original equipment and competitive bimetal bearings.
( 251 )
$28.99
—
$52.99
For maximum performance and durability on the street or at the track, trust Fram HP Series oil filters. They offer twice the oil flow rate and four times the dirt-holding capacity of standard oil filters. Their extra-thick steel cans and heavier gauge tapping plates are designed to withstand the high pressures and flexing caused by demanding driving conditions. Tough steel end caps hold a spiral-shaped center tube to offer more durability and protection against collapse. Fram HP Series oil filters are compatible with all oil types and have been optimized for racing and high performance street cars. Additional features include: * Low-restriction racing media designed for high oil flow * 94 percent efficiency at 20 microns * Silicone anti-drainback valve on many applications * 10 to 18 gpm recommended maximum oil flow, depending on model * Maximum burst pressure: 350 to 500 psi, depending on model * Maximum operating pressure of 200 psi * Screen over bypass valve for extra protection against large contaminants * High-flow bypass valve * Flanged steel end caps
( 124 )
$23.99
—
$36.99
ARP High Performance Series head bolt kits are tough. They are rated at 180,000 psi--15 percent stronger than Grade 8 fasteners. They come available with a reduced wrenching hex head or 12-point head that help eliminate the need for valvetrain removal when re-torqueing cylinder heads.
( 1026 )
$45.99
—
$51.99
Clevite coated H-Series rod bearings were developed primarily for NASCAR racing, but are also well suited to other types of competition engines. They're especially good for engines that run at medium-to-high revs. They have hardened-steel backings with thin overlays and a high crush factor, plus a medium level of eccentricity. H-Series bearings feature Clevite's exclusive TriArmor coating, the industry's only moly/graphite treatment. The sophisticated blend, in a low-friction PTFE polymer base, offers extraordinary protection and lubricity. They also have enlarged chamfers at the sides for greater crank-fillet clearance and are made without flash plating for better seating. The Clevite coated H-Series rod bearings are available with various under-sizes, including 0.001 in. of clearance for polished journals.
( 10 )
$20.99
—
$25.99
King SI-Series main bearings are recommended for OE applications. These replacement bearings are designed for aftermarket gasoline or diesel engine rebuilding—and performance engines with factory crankshafts. The bearings have an improved crankshaft finish for reducing microscopic ferrite peaks on improperly ground or polished nodular cast iron crankshafts. King SI-Series main bearings feature improved oil clearance to reduce wear and increase engine life, which in turn reduces operating noise, vibration, and excess oil flow. Order the bearing set designed for fitment on your make and model.
( 79 )
$20.99
—
$55.99
ARP High Performance Series main bolts are rated at 180,000 psi and a popular premium replacement for OEM fasteners. Designed to meet the exacting standards and demands of professional engine builders, ARP bolts are forged from 8740 chromoly steel and feature a reduced wrenching head, large underhead radius, and rolled threads for the utmost in reliability. The threads are rolled after heat-treating which gives them about 2,000 percent better fatigue strength than most main bolts that are threaded prior to heat-treating. Hardened parallel-ground washers are included with each kit.
( 174 )
$35.99
—
$50.99
Sealed Power A-Series rod bearings can actually polish the journals on your crankshaft. That's because there's a small percentage of silicon mixed in with the aluminum and tin that make up the bearing-surface alloy. The silicon is there for wear resistance, but its toughness actually smoothes the journals of a crank with a surface that hasn't been optimized! This special surface alloy is laid over a high-strength 1010 steel backing and delivers improved seizure and corrosion resistance, as well as better wall variance control. It also helps to minimize debris embedding, which can score the crank's surface. Order the replacement bearings designed for your vehicle make and engine application.
( 33 )
$22.99
—
$55.99
Edelbrock's Signature series black valve covers are engineered for function and styled for good looks. They feature a powdercoated finish for long lasting good looks, and have stock-style breather baffles that prevent oil passage to the PCV valve. They accept all emissions equipment, including PCV valves, and include rubber grommets for the breather and PCV valve holes. The Edelbrock Signature Series black valve covers clear most aluminum rocker arms and moderate lift cams. Some applications come in a high-profile design that's 1 1/4 in. taller than stock, and clears most roller rockers and valvetrain components, and a low-profile design that clears air conditioning and alternator brackets.
( 122 )
$59.95
Howards Cams Performance Series C1010 pushrods are manufactured from .060 in. wall C1010 low-carbon steel material. They provide over 20 percent more column strength than OEM pushrods. Their advanced design eliminates ball breakage. They are heat-treated for use with guideplates and are designed for up to 500 lbs. of valve spring pressure.
( 57 )
$46.99
—
$52.99
Edelbrock's Elite series valve cover breathers are made of die-cast aluminum and are polished to a high shine. They have an Allen head bolt-on cover for access to their internal foam filter, and come available either with or without the famous Edelbrock script logo. These breathers will match your Elite series valve covers. They also come in your choice of a bolt-on 90 degree side-mount type, a bolt-on 30 degree top-mount style, or a push-in top-mount type. The internal foam filter element won't leak or clog, the way those other types of breathers on the market can.
( 49 )
$33.95
—
$40.95
ACL Performance offers Race Series rod bearing sets for a wide range of vehicles. These high performance tri-metal engine bearings are designed to withstand higher RPM conditions. They feature a high-strength overlay plate with reduced thickness for improved fatigue properties. Select the crankshaft undersize and quantity recommended for your year/make and engine application. Additional details: * Hardened steel backs on all rod bearings to improve the support of the bearing lining and assist with bearing retention in the housing. * Increased crush for improved bearing retention * Elimination of flash plating on the back of the bearings to improve heat transfer through the bearings and to maximize the grip between the bearings and its housing * Increased eccentricity to compensate for bore distortion at high RPM and to assist in the formation of hydrodynamic oil films * 3/4 in. grooved main bearings to optimize bearing load carrying surface area and oil flow to the conrod bearings * Tight consistent wall tolerances to help you maintain consistent clearances * Enlarged ID chamfers on bearing edges (where required) to accommodate large fillet radius on performance crankshafts
( 7 )
$37.99
—
$52.99
Edelbrock's Signature series chrome valve covers are engineered for function and styled for good looks. They're triple chrome plated for long lasting good looks and have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valves, and include rubber grommets for the breather and PCV valve holes. The covers clear most aluminum rocker arms and moderate lift cams. Some applications come in a high-profile design that's 1 1/4 in. taller than stock and clears most roller rockers and valvetrain components, and a low-profile design that clears air conditioning and alternator brackets.
( 157 )
$59.95
These Sealed Power MA Series main bearings can actually polish the journals on your crankshaft. That's because there's a small percentage of silicon mixed in with the aluminum and tin that make up the bearing-surface alloy. The silicon is there for wear resistance, but its toughness actually smoothes the journals of a crank whose surface hasn't been optimized! This special surface alloy is laid over a high-strength 1010 steel backing and delivers improved seizure and corrosion resistance, as well as better control of wall variance. It also helps to minimize debris embedding, which can score the crank's surface.
( 75 )
$35.99
—
$54.99
Sting the competition with the full-body design of Scorpion Race Series roller rocker arms. They're precision-crafted via high-tech manufacturing methods, then fully CNC-machined. These rockers offer more clearance for retainers and springs, and can easily handle .950 in. lift and 950 lbs. of open spring pressure. The surfaces are micro-polished and anodized for looks, protection, and maximum durability. Scorpion rocker arms are available in nearly 200 fitment options; order the set recommended for your application. More speed for your high performance passion! Additional features include: * Aerospace-grade 7000 Series aluminum for maximum strength and durability * Needle bearing fulcrum and roller tip * Precision-ground needle bearings * Centerless ground trunnion, ground pin, and roller * Burr-free trunnion through hole * Directed oiling * Large machined seat and thick-walled adjusting nut (polylock) * Pedestals machined from solid steel * Black oxide coated steel parts * 1.600 in. fulcrum width * Clear 1.625 in. O.D. valve springs
( 211 )
$26.41
—
$30.53
ARP Pro Series connecting rod bolts are precision CNC-machined to exacting specifications and designed for optimum reliability. They are heat-treated and threads are rolled to provide up to ten times more fatigue strength. This makes them far superior to standard OEM fasteners in terms of durability, and fully capable of handling the extra stress of high-combustion engines.
( 67 )
$24.99
—
$27.99
ARP Pro Series main bolts are application-specific and rated at 190,000 psi. Designed for use in competition engines, as well as to meet the exacting standards and demands of professional engine builders, ARP bolts are forged from 8740 chromoly steel and feature a reduced wrenching head, large underhead radius, and rolled threads for the utmost in reliability. The threads are rolled after heat-treating which gives them about 2,000 percent better fatigue strength than most main bolts that are threaded prior to heat-treating. Hardened parallel-ground washers are included with each kit.
( 14 )
$47.99
Federal Mogul CP-Series rod bearings feature classic tri-metal construction and are a good choice for either street or moderate competition use. They have rugged 1010 steel backings, covered by Federal Mogul's H-24 copper-lead alloy. On top of this is a nickel barrier, followed by the tri-metal (lead-tin-copper) overplate that gives these bearings their strength and fatigue resistance. The bearings are then entirely covered with a flash coating of tin. Order the set designed for use with your make/model and engine application.
( 115 )
$21.99
—
$92.99
Lokar's Midnight Series direct-mount engine dipsticks are a part of their black stainless steel products, assembled with matching black anodized aluminum fittings. The slim design allows for mounting inside of your headers, and the flexible inner dipstick measuring cable gives you an accurate reading of engine oil level. Order the model designed to fit your vehicle and engine block application.
( 2 )
$50.95
Specially developed for use with Diamond's pistons, the H-13 Series wrist pins are an H-13 tool steel alloy—quite possibly the best all-round wrist pin material for high horsepower "power adder" engines. Designed to further reduce reciprocating weight, the H-13 Series piston pins have a Rockwell hardness around Rc54, and easily accepts a DLC (Diamond-Like Carbon) coating. Make no mistake, during high-contact stress and impact loading applications, you'll want the confidence that the H-13 Series wrist pins can provide! Order the piston wrist pins designed for your application needs.
Not Yet Reviewed
$35.00
Continental OE Technology Series Multi-V belts are factory-style replacements covering virtually all vehicle applications. These new straight-ribbed multi-V belts offer original fit and function that professional technicians appreciate for their customers. The serpentine belts are constructed with advanced EPDM rubber compounds that improve durability and deliver a quieter ride. They're available in well over a hundred lengths, with rib options ranging from three to 14. Order the model recommended for your car, truck, van, SUV, or crossover.
( 325 )
$20.99
—
$53.99
ARP Pro Series cylinder head studs are cold-forged to ensure molecular integrity. They're heat-treated prior to thread rolling and machining. ARP Pro Series kits are also available with 12-point nuts, and all studs come complete with hardened parallel washers for an even load distribution and accurate torque readings. With hundreds of models ready to ship, these cylinder head fasteners can be ordered for virtually any style engine.
( 787 )
$34.99
ARP High Performance Series connecting rod bolts are made from seamless and defect-free 8740 chromoly steel. All ARP rod bolts are heat-treated before grinding and thread rolling and have a large underhead radius for greater strength. Guaranteed to pass magnetic inspection testing, these bolts are nearly five times stronger than OEM bolts. They're used in applications ranging from stock replacement to Circle Track, marine, and drag racing engines.
( 255 )
$42.99
—
$52.99
PAC Racing 1200 Series drag race valve springs are great for allowing you to get the most performance out of your engine. Select them when you're upgrading camshafts or doing engine rebuilds. The 1200 Series use a premium alloy that outperforms automotive industry standards; and PAC Racing processes the alloy to aerospace shot-peening standards to achieve superior fatigue dependability. This ensures that the springs maintain the load needed to perform during the most demanding times.
( 7 )
$25.31
—
$30.02
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
