Filters
Clevite H-Series main bearings were developed primarily for NASCAR racing, but are well suited to other types of competition engines as well. They're especially good for engines that run at medium-to-high revs. They have steel backings with carefully selected overlays and a high crush factor, plus a medium level of eccentricity. H-Series bearings have enlarged chamfers at the sides for greater crank-fillet clearance and are made without flash plating for better seating. They are also available with either 180 degree or 360 degree oil grooves, as well as an extra 0.001 in. of clearance.
( 133 )
$100.99
—
$274.99
Clevite P-Series main bearings are the oldest members of the Clevite 77 bearing family and are intended for high-revving engines. To compensate for the high-load factors and distortion in these engines, these bearings have higher eccentricity and a high crush factor. P-Series bearings are constructed of tri-metal cast copper lead. They have a steel back for support, a cast copper lead lining to withstand the loads of engine operation, and an electroplated babbit overlay on the running surface to provide searing surface qualities. In addition, the oil grooves on most applications extend all the way around both halves for better oiling. Clevite P-Series main bearings are an ideal design, producing a degree of conformability, embedability, slipperiness, and fatigue resistance, not found in original equipment and competitive bimetal bearings.
( 248 )
$100.99
—
$222.99
Built with enhanced tri-metal, King XP-Series main bearings have a layered copper lead construction, with a nickel plate barrier and lead/tin/copper Babbitt overlay over a steel backing--in an adhesion process that provides superior stability and durability. King's advanced control measures hit a bull's-eye, maintaining wall thickness tolerances far tighter than their competitors: an amazing +/- .0001 in. The XP-Series main bearings are narrowed for large radii crankshafts and feature enlarged, chamfered oil holes with full, 3/4 in., or 1/2 in. grooving for improved oiling. They deliver consistent and reliable performance with a high-load capacity. These race-only Xtreme Performance (XP-Series) Tri-Lecular main bearings are proven track-tough to handle the ground-shaking power of your race engine. Hundreds of sets are available; order the bearings recommended for your vehicle.
( 39 )
$100.99
—
$239.99
Give your engine the winning edge with King XP-Series coated rod bearings. Built off the revolutionary XP-Series tri-metal construction, King's factory-applied pMaxKote nano-composite coating takes protection to the next level without adding any additional thickness! These high performance race bearing sets are available for fitment on a wide range of specific vehicle applications. pMaxKote provides: * Superior seizure resistance * Superior cavitation resistance * Superior wear resistance * Superior protection against oil starvation
( 10 )
$108.99
—
$254.99
King XP-Series rod bearings feature advanced metallurgical and geometric technologies that meet extreme performance loads. They were developed for all performance applications that use forged steel aftermarket crankshafts and produce high loads for extended periods. King focuses on one product—bearings—and nothing else. Their innovative race-only Xtreme Performance Max Black Tri-Metal rod bearings have a 24 percent stronger overlay and 17 percent more fatigue strength by using a micro process called SecureBond. Built with enhanced tri-metal, King XP-Series rod bearings layer copper-lead construction with a nickel plate barrier and a lead/tin/copper Babbitt overlay over a steel backing in an adhesion process that provides superior stability and durability. King's advanced control measures hit a bull's-eye, maintaining wall thickness tolerances far tighter than their competitors—at an amazing +/- .0001 in.! XP-Series rod bearings are narrowed on the crank cheek side with increased crush height for improved bearing-to-bore contact, heat transfer, and reduced spin potential in high-rpm applications.
( 63 )
$100.99
—
$247.99
ACL Performance Race Series main bearing sets deliver everything performance bearings should be by utilizing design, metallurgy, engineering, precision quality control, and of course, years of knowledge and experience. Main bearings feature multi-layered tri-metal copper alloy construction that blends characteristics to provide high strength and excellent seizure resistance. They are manufactured to exact tolerances ensuring a reliable fit and helping to maintain consistent clearances. Main bearings are augmented with extended grooves, as well as other bearing enhancements, like increased crush, bearing eccentricity, and enlarged I.D. chamfers. ACL Performance Race Series main bearing sets are produced in standard and extra clearance versions, with or without friction reducer coating, and with modifications to meet specific build requirements, such as narrowed bearings that permit additional edge clearance when running crankshafts with exceptionally large fillet radii. In the heat of competition proven technology always comes through. The choice for your build should always be ACL Performance Race Series engine bearings. Choose the main bearing set designed for your vehicle.
( 1 )
$100.99
—
$263.99
Dura-Bond took their high performance bearings and coated them with a secondary dry film lubricant for added protection against oil starvation.
( 40 )
$100.99
—
$175.99
If you liked the results that you used to get with Vandervell bearings--especially their higher conformability--then you should love Clevite V-Series rod bearings, which basically duplicate the Vandervell items. Built on un-plated, hardened-steel backings for better dimensional accuracy and bore contact, they have low-to-medium eccentricity. The biggest difference between V-Series and other Clevite 77 bearings is their lead-indium surface alloy, which gives them that extra conformability. V-Series bearings are available in narrower versions to provide greater crank-fillet clearance, as well as in extra-clearance variations that provide an additional 0.001 or 0.002 in. of clearance.
( 6 )
$256.99
—
$269.99
King HP-Series main bearings are recommended for street and strip performance applications. They're designed for blown, turbocharged, NOS, and alcohol-fueled engines using aftermarket crankshafts. These main bearings have greater eccentricity for superior oiling at high rpm, and a chamfered surface for large radii crankshafts. HP-Series bearings also feature large, chamfered oil holes—and are available in 1/2 grooving for improved oiling to withstand high-rpm applications. Order the bearings designed for fitment with your specific engine.
( 45 )
$100.99
—
$154.99
King HP-Series cam bearings are precision-machined to tight tolerances to control installed oil clearances, reducing operating bearing pressure. These cam bearings are constructed from seamless steel tubing with a thin layer of lead based babbit material to reduce microscopic deflections. The babbit is quickly cooled in the casting process to achieve a very fine grain structure, doubling tensile strength, therefore, the HP-Series offers much more fatigue strength than conventional bearings, and can withstand racing spring loads, while maintaining the excellent surface characteristics of babbit. King also offers HP-Series bearings with a fluoropolymer coating. Bearings with this coating retain engine oil on the surface, even under extreme heat and pressure—a great advantage! Plus, being a lubricant, it provides backup during start-up and in the event of momentary oil starvation. Use track-tough King HP-Series cam bearings in your engine—and experience the difference.
( 13 )
$103.99
—
$292.99
If you're building a serious performance engine, then you'll want to consider Speed-Pro Competition Series main bearings. They were developed in NASCAR and Pro Stock competition, so you know they're tough. The bearings are built on premium 1020AK steel backings and overlaid with Speed-Pro's super-duty H-14 alloy. That layer is then covered with a nickel barrier, followed by a thin lead-tin-copper overplate. However, unlike other performance bearings, there is no flash tin layer on top of that. Speed-Pro's engineers have determined that such a layer can actually move around under high loads—sometimes with undesirable consequences. Depending on the application, these main bearings have oil grooves for enhanced lubrication, while maintaining a maximum bearing surface area. They also feature Speed-Pro's exclusive contoured-flange thrust bearing technology for higher thrust-loading capacity. Competition Series main bearings are available in nearly a hundred configurations for countless vehicle and engine applications.
( 62 )
$101.99
—
$217.99
If you're building up a Dart block and want the best bearings with the correct sizing, then you'll want Dart cam bearings. They're fully grooved, made from steel-backed babbit, and specifically designed for high performance use. To all of this, Dart adds their own moly-PTFE coating for even better performance and durability. This coating is approximately 0.0005 in. thick, which translates into 0.001 in. less overall clearance.
( 33 )
$116.20
—
$234.84
Summit Racing™ offers Race Series main bearing sets for a wide range of applications—including many Chevrolet, Ford, Chrysler, Dodge, Jeep, Ram small block, big block, and Hemi engines from the early 1960s and up. Main bearings hold the crankshaft in place and allow it to rotate within the engine block. These performance replacements are machined from tri-metal copper-lead alloy, and are available in numerous upper/lower groove styles and engine crankshaft undersize options. Order the set recommended for your vehicle.
( 3 )
$113.99
—
$161.99
ACL Performance offers Race Series rod bearing sets for a wide range of vehicles. These high performance tri-metal engine bearings are designed to withstand higher RPM conditions. They feature a high-strength overlay plate with reduced thickness for improved fatigue properties. Select the crankshaft undersize and quantity recommended for your year/make and engine application. Additional details: * Hardened steel backs on all rod bearings to improve the support of the bearing lining and assist with bearing retention in the housing. * Increased crush for improved bearing retention * Elimination of flash plating on the back of the bearings to improve heat transfer through the bearings and to maximize the grip between the bearings and its housing * Increased eccentricity to compensate for bore distortion at high RPM and to assist in the formation of hydrodynamic oil films * 3/4 in. grooved main bearings to optimize bearing load carrying surface area and oil flow to the conrod bearings * Tight consistent wall tolerances to help you maintain consistent clearances * Enlarged ID chamfers on bearing edges (where required) to accommodate large fillet radius on performance crankshafts
( 5 )
$100.99
—
$249.99
If you liked the results you used to get with Vandervell bearings--especially their higher conformability--then you should love Clevite V-Series main bearings. Built on unplated steel backings, for better dimensional accuracy and bore contact, they have low-to-medium eccentricity. The biggest difference between V-Series and other Clevite 77 bearings is their lead-indium surface alloy, which gives them that extra conformability. Unlike Vandervell main bearings, Clevite V-Series main-bearing sets use a single-piece thrust bearing, so you don't need separate, assembled thrust bearings. Extra-clearance variations are available to provide an additional 0.001 or 0.002 in. of clearance.
( 5 )
$109.99
—
$254.99
Clevite coated H-Series main bearings were developed primarily for NASCAR racing, but are also well-suited to other types of competition engines. They are especially good for engines that run at medium-to-high revs. They have steel backings with carefully selected overlays and a high crush factor, plus a medium level of eccentricity. These H-Series bearings feature Clevite's exclusive TriArmor coating, the industry's only moly/graphite treatment. The sophisticated blend, in a low-friction PTFE polymer base, offers extraordinary protection and lubricity. Clevite H-Series bearings have enlarged chamfers at the sides for greater crank-fillet clearance and are made without flash plating for better seating. They come with 180 degree oil grooves, and can be ordered with an extra 0.001 in. of clearance if needed.
( 3 )
$142.99
—
$209.99
P-Series rod bearings are the oldest members of the Clevite 77 performance bearing family. They're intended for high-revving engines, especially those where the high rpm cause the rod bores to narrow. To compensate for this distortion, these direct replacements have higher eccentricity and a high crush factor. Clevite P-Series rod bearings are built on hardened-steel backings with extra-thin overlays, and their lower sections have dowel holes for use with aluminum rods, and there are extra-clearance variations available with an additional 0.001 in. of clearance. Order the model designed for your vehicle and engine application.
( 275 )
$102.99
—
$158.99
Give your engine the winning edge with King XP-Series coated main bearings. Built off the revolutionary XP-Series tri-metal construction, King's factory-applied pMaxKote™ nano-composite coating takes protection to the next level without adding any additional thickness! Order the replacement main bearings designed for fitment with your engine. pMaxKote™ provides: * Superior seizure resistance * Superior cavitation resistance * Superior wear resistance * Superior protection against oil starvation
( 6 )
$105.99
—
$308.99
King HP-Series rod bearings were developed mainly for drag race applications needing a material harder than the Babbitt top layer. These applications demanded a structure that could withstand high loads for short durations and still offer higher embeddability and compatibility. In response, King developed the HP-Series, featuring the Alecular metal structure. The HP-Series is also suited for many performance applications with nodular cast iron crankshafts, such as street, strip, and some levels of Circle Track racing. Order the set recommended for your vehicle. HP-Series bearings are particularly suitable for the following cases: * When a tri-metal bearing's Babbitt overlay extrudes over the sides, migrates to one end, or is physically removed by the crankshaft * When the intermediate layer of a tri-metal bearing is exposed, damaging the crank journal and requiring expensive grinding or replacement * When contaminants enter the oil stream, scratching and damaging the crankshaft journals
( 34 )
$100.99
—
$137.99
Today's engines operate under very demanding conditions. When these Sealed Power main bearing sets are used in performance applications, all components are pushed to their limits—and many must be changed to meet these special demands. Federal Mogul, a longtime supplier to both OEM and the aftermarket, has responded to this challenge with its tri-metal, copper-lead, high performance main bearing sets. They're tested in the lab and proven on the track. The bearings are available for various crankshaft undersizes, for direct replacement or performance usage on a wide range of specific applications.
( 96 )
$100.99
—
$246.99
Economical Dura-Bond standard cam bearings feature round babbit construction for low friction, outstanding conformability, and added embeddability.
( 92 )
$101.99
—
$226.99
King offers SX-Series main engine bearings for a variety of vehicles, including Jeep and RAM. The direct replacements are machined from tri-metal material and are sold in sets. Order the bearings recommended for your application.
( 1 )
$156.99
These Sealed Power MA Series main bearings can actually polish the journals on your crankshaft. That's because there's a small percentage of silicon mixed in with the aluminum and tin that make up the bearing-surface alloy. The silicon is there for wear resistance, but its toughness actually smoothes the journals of a crank whose surface hasn't been optimized! This special surface alloy is laid over a high-strength 1010 steel backing and delivers improved seizure and corrosion resistance, as well as better control of wall variance. It also helps to minimize debris embedding, which can score the crank's surface.
( 73 )
$104.99
—
$137.99
King SV-Series rod bearings provide movement with minimal power loss. Connecting rod bearings provide rotating motion of the crank pin within the connecting rod, which transmits cycling loads applied to the piston, and King SV-Series will provide this function well to handle your extreme load engines. These King SV-Series connecting rod bearings are copper-based and lead-free, offering great wear resistance, as well as load capacity.
( 3 )
$105.99
—
$236.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
