Availability
Trail-Gear Power Flow power steering pump upgrade kits remedy a common flaw in Toyota trucks. The stock pump is just barely able to supply the volume and pressure needed to run hydraulic-assist steering—putting out 1,300 psi at only one gallon per minute. The original pump is not able to provide enough fluid to run both the stock steering and the demands of a ram, especially at low rpm. Drilling out the restrictor plates in a stock pump for more volume often leads to pump failure. The answer is a replacement "TC" style pump. This provides the full fluid volume your steering box and ram are looking for, even at idle. These kits include a 1,650 psi pump, pump bracket, reservoir, reservoir bracket, belt, fittings, hoses, and hardware. The pump kits are designed to work with stock or ram drilled IFS power steering boxes. Additional notes: * The pump and bracket are designed to fit all Toyota 4-cylinder 4WD motors from 1979-95 * A large power steering fluid cooler (included) is required on the low-pressure side of the system * Pump bracket works in conjunction with stock idler bracket * If your truck is not currently equipped with power steering, you will need to purchase the idler bracket and replace the steering gearbox with one designed for use with power steering * The stock fan belt will not work with this pump and will need to be replaced with a Napa 9430 belt. Belt is included with kit. * Note: Never use ATF fluid or a semi-synthetic blend. This will void the warranty. It's okay to use standard power steering fluid or a full synthetic.
( 2 )
$899.99
Trail-Gear FJ-80 knuckle rebuild kits are available with or without wheel bearings. The kits contain all of the replacement parts you need to service your steering knuckles. Trail-Gear FJ80 knuckle kits will service both left and right knuckles. Trail-Gear FJ-80 knuckle rebuild kits typically include: * Gaskets, felts, seals, washers and shims * Inner axle seals and outer felt covers
( 5 )
$129.99
—
$199.99
Looking for a steering box for your Toyota's steering system? Trail-Gear IFS remanufactured steering boxes are thoroughly flushed and rebuilt. All boxes are completely tested before shipping.
( 3 )
$699.99
Has it been a while since you serviced your knuckles? Trail-Gear knuckle rebuild kits contain all standard replacement parts, including gaskets, felts, seals, washers, and shims to do the job done right. They even include outer felt covers--a Trail-Gear exclusive! If you're using your truck in the rocks you will want to replace these covers when you service the knuckles. Kits are offered with or without wheel bearings. Service your knuckles with Trail-Gear knuckle rebuild kits.
( 4 )
$149.99
—
$199.99
Trail-Gear Samurai high steer kits are specifically engineered to work with stock Samurai axles--and they're a must-have for a "spring over axle" setup. They include solid-forged 8620 steel steering arms, a heavy-duty 1 1/4 in. x .250 in. wall DOM drag link and tie rod, FJ80 tie rod ends, and all necessary hardware. There's even a hard-to-find 1:10 taper reamer for reaming out your stock pitman arm. As with all Trail-Gear products, installation is easy, and these high steer kits fit all Suzuki Samurai engines.
( 4 )
$599.99
Trail-Gear heavy-duty transfer case mounts can handle the abuse of rock crawling and the ultra-low torque of dual cases. Stamped out of 1/4 in. thick steel plate and then welded on a jig to ensure the best fit possible, these mounts are fitted with polyurethane bushings and coated with zinc for lasting performance and durability. Eliminate the worries of a busted T-case mount on the trails with the installation of bomb-proof Trail-Gear heavy-duty transfer case mounts.
( 5 )
$59.99
—
$149.99
After years of development and testing, Trail-Gear fully loaded Six Shooter kits have set a new standard for Toyota knuckle strength and reliability. They totally eliminate the problem of broken steering knuckles and studs. The addition of two studs in each arm effectively prevents the steering arm from becoming loose or shearing off the studs under extreme loads. The knuckle housing was designed with thicker-than-stock material, and larger gussets have been added around the outside of the knuckle for extra strength. Precision CNC-machined, each set of knuckles and steering arms are inspected and tested for the highest quality of products that Trail-Gear can deliver. These kits include a special 6-hole shim pack for use between the top of the knuckle and the steering arm assembly. A minimum of four additional steering arm studs are required for installation.
( 3 )
$499.99
—
$699.99
Trail-Gear solid axle steering kits support your determination to put together your own SAS kit to lift your first-generation Tacoma. How, you ask? When you have trouble finding the right parts to link your steering to an IFS steering box, you know the answer--Trail-Gear. These TG solid axle kits utilize the same steering parts from their own SAS kits to take the guesswork out of making your own steering linkage. You'll receive an adjustable-length double-D steering shaft, a firewall plate, a steering shaft seal, and U-joints for both ends of the shaft. Trail-Gear is ready to lend a hand with their solid axle steering kits.
Not Yet Reviewed
$379.99
Trail-Gear pitman arms are designed from solid forged steel construction, and are ideal for use with crossover steering. Replacing your pitman arm is recommended if the original is worn-out or, in most cases, if your steering box is being changed out. These strong, extra-wide one-piece arms will allow the use of FJ80 tie rod ends. They're available in flat style or with the same drop as the factory pitman arm.
( 1 )
$129.99
Trail-Gear high steer crossover steering kits get you have you crawling over the rocks in no time. Stock steering just can't do the job like flexible crossover steering. TG high steer kits outfit your rig with the unbeatable quality of super beefy, solid forged steering arms, a heavy-duty pitman arm, rod ends, and durable .250 in. wall steering rods. They offer a precision fit for easy assembly and are available with flat arm or drop pitman arm, and 4-stud or 6-stud setups. Is your steering wheel on the right? TG also offers a right hand drive! If you're tired of broken stock steering arms, make the switch to Trail-Gear high steer crossover kits.
( 1 )
$549.99
—
$649.99
Got a broken OE rubber motor mount? Trail-Gear Bomb Proof engine mount kits offer the quality and strength you need. The base of these motor mounts is made from 1/4 in. plate. The surface plate that the motor sits on is made out of 3/8 in. material and has a Class 10.9 bolt that is mechanically locked to the engine mount plate--not just threaded in. Bomb Proof mounts are given a silver zinc plating that looks sharp and will last a lifetime. The bushings are made out of high-grade polyurethane for added durability, and the mount holes are slotted so that your install is easy. Upgrade your vehicle to Trail-Gear Bomb Proof engine mount kits.
( 9 )
$189.99
Truck owners are very impressed by the lineup of Trail-Gear Rock Assault Ram steering assist kits. For example, the Toyota kits feature a selection of various-sized stroke hydraulic rams--with high-temperature inner and outer seals for long life and no leaks. Each ram includes a 3/4 in. rod that's a full 50 percent stronger than other rods on the market. The specially formed 1/4 in. heavy-duty plate steel brackets make installation a snap. Here are the parts included in most Trail-Gear Rock Assault Ram steering assist kits: * Ram with high-temperature inner and outer seals * Rod ends with jam nut * Ram bracket for axle housing * Ram bracket for tie rod * Two hoses * Two JIC 90 degree elbows * Two 1/4 in. NPT x #6 JIC steering box fittings * Mounting hardware * Instructions with photos These kits do require: * Trail-Gear High Steer crossover steering with 1.25 in. tie rod * Tapped steering box
( 3 )
$449.99
Whether you are hitting the trail, or ripping through the desert, Trail-Gear Performance bump stops will allow you to get the most out of your vehicles suspension by eliminating harsh bottom outs. Offered in 2 in. and 2.5 in. body diameters, the 2.5 in. models will absorb more impact energy and are recommended by Trail Gear for vehicles over 5,000 lbs. or trucks with highly leveraged A-arms or trailing arms. Of course, both sizes are sure to improve your overall off-road experience. Trail-Gear Hydraulic smooth body bump stops are fully rebuildable, easily tunable through the Schrader valve on top, and TG's unique automatic velocity sensitive valving technology saves you time by eliminating the need to adjust shim packs. The bump stops also help prevent damage from occurring to expensive shocks and suspension components by absorbing impacts at full suspension compression. Trail-Gear smooth body, pin top bump stops are available in 2 in., 3 in., and 4 in. travel options, and can be purchased individually or in sets that will also include four 1/4 in. thick ASTM A36 steel weld-on universal mounting brackets. Choose the size, stroke, and quantity desired for your vehicle. Hydraulic bump stop details and benefits: * Zinc-Plated SAE 1020 steel body * Hard chromed SAE 1045 steel rod * 6061 T-6 aluminum seal housing with dual PTFE coated bronze rod guides * Viton® O-ring with U-cup seal * 6061 T-6 aluminum piston * Automatic velocity sensing valve * Anodized 6061 T-6 aluminum end cap with polyurethane wiper seal * Replaceable Delrin® contact pad for smooth and quiet operation * Tunable by adjusting the nitrogen pressure and or oil volume * Schrader valve with machined aluminum cap for quick and easy pressure adjustment * Zinc-plated steel locking nut * Adjustable from 75 to 300 psi; ships pre-charged to 200 psi--a great starting point for tuning your suspension
Not Yet Reviewed
$399.99
Trail-Gear heavy-duty steering kits solve feedback issues caused through the stock steering setup. Bigger tires and a lifted suspension are necessities for off-roading today—unfortunately, the combination can cause problems. TG kits will reduce steering vibrations, so you can enjoy a more comfortable driving experience. They offer kits for multiple applications that will strengthen your setup for more assurance on the trails. Trail-Gear steering kits include right and left-hand thread heavy-duty FJ80 tie rod ends, drag link, and hardware. The tie rods and drag link are made from hefty 1/4 in. thick wall DOM tubing. Your choice of kit may also include steering stabilizer with 9 in. stroke and hardware, or a hard-to-find 1:10 taper reamer for reaming out your stock pitman arm and steering arms.
Not Yet Reviewed
$299.99
—
$399.99
Trail-Gear double-shear brackets are made from 1/8 in. thick 4130 chromoly steel for fabrication strength. They're designed for double-shear mounting limit straps or seat belt tabs. The brackets are sized to mount a 1/2 in. bolt and require welding for mounting on your vehicle.
( 4 )
$9.99
Providing improved power steering for off-roading, Trail-Gear power steering pumps replace your stock models with high-performance reliability. Their TC-style pumps are built to handle extreme heat, with each one receiving a bench test to ensure quality. They are available in two styles -with or without an anodized aluminum pulley. When you are on the road, stock is okay--but for off-road, you need trail-tested gear. Order the Trail-Gear power steering pumps best suited for your application.
( 6 )
$399.99
—
$899.99
Lift kits and taller tires are a necessity when navigating serious off-road trails. Whether you need to make adjustments to pinion angles or tire fitment in the fender wells, Trail-Gear leaf spring perches have you covered. These 1/4 in. steel perches feature the standard center hole, with additional holes drilled 1 in. in front and behind the center to avoid crunching fender well sheet metal. When running longer rear springs for greater flex, you may need to move the axle forward—while larger tires with stock length springs sometimes hit the front, requiring the axle to be moved back. If you're adding a larger lift, it's advised to change the angle of the perches in order to set proper pinion angles. Properly mounted lift kits and taller tires can greatly improve your vehicle's off-road capabilities, but steep driveline angles and tires hitting the edges of fender wells will bring nothing but trouble. Give your vehicle many options with Trail-Gear leaf spring perches.
( 6 )
$39.99
Trail-Gear weld-in frame gussets are just what the doctor ordered for reinforcing tubing and plate in high-weight and high-stress areas. These strong steel gussets are ideal for tube chassis, roll cages, frames, or in most 90 degree corners where welding has occurred. There are numerous designs available--choose your Trail-Gear weld-in frame gussets for safe reinforcement.
( 8 )
$2.99
—
$39.99
With all of the choices on the market for solid axle conversion, you're probably wondering what makes Trail-Gear IFS Eliminator kits stand out? These kits contain the highest quality and most complete parts roster at an affordable price. Plus, Trail-Gear offers the package in three different ride heights! Kits include: * Front leaf springs (your choice of 3, 4, or 5 in. spring) * High Steer crossover steering kit * Front drop hanger with greasable bolts * Greasable 5 in. shackles * Frame tubes and jigs * Steering stabilizer kit * U-bolt flip kit * (2) Shock hoops * (2) Bilstein shocks * (2) Front brake lines * (2) Vented rotors * (2) Bump stop extensions * (2) Wheel spacers * (2) Bump stops * Front axle gusset * Axle diff armor * Knuckle service kit * Wheel bearing kit * Motor mount cover plates * Spring pad * Instructions
( 1 )
$1,799.99
If you're installing crossover steering, the time you'll save with one of these mounting kits is well worth the investment. They make swapping to the Trail-Gear IFS steering box much easier. The heavy-duty kits feature 3/16 in. inner and 1/4 in. outer frame reinforcing plates, with angled leading and trailing edges to avoid frame cracking. You'll also receive Grade 8 bolts, crimp nuts, and dependable DOM tubing to complete the project.
( 3 )
$89.99
If you need to relocate your rear shackle mounts in order to install longer suspension springs, it's the perfect time to upgrade to Trail-Gear leaf spring shackles. These 1/4 in. steel plate units are stronger than the original factory shackles, offering more security when scaling rough terrain. Trail-Gear leaf spring shackles will use your OEM bushings or stock replacements. Order the pair designed for your vehicle application.
( 5 )
$129.99
Whether you are hitting the trail, or ripping through the desert, Trail-Gear Performance bump stops will allow you to get the most out of your vehicles suspension by eliminating harsh bottom outs. Offered in 2 in. and 2.5 in. body diameters, the 2.5 in. models will absorb more impact energy and are recommended by Trail Gear for vehicles over 5,000 lbs. or trucks with highly leveraged A-arms or trailing arms. Of course, both sizes are sure to improve your overall off-road experience. Trail-Gear Hydraulic threaded body bump stops have anodized aluminum locking rings for quick and easy adjustment. They are fully rebuildable, easily tunable through the Schrader valve, and TG's unique automatic velocity sensitive valving technology saves you time by eliminating the need to adjust shim packs. The bump stops also help prevent damage from occurring to expensive shocks and suspension components by absorbing impacts at full suspension compression. Trail-Gear threaded body bump stops are available in 2 in., 3 in., and 4 in. travel options, and can be purchased individually or in sets that will also include four 1/4 in. thick ASTM A36 steel weld-on universal mounting brackets and spanner wrench. Choose the size, stroke, and quantity desired for your vehicle. Hydraulic bump stop details and benefits: * Zinc-Plated SAE 1020 steel body * Hard chromed SAE 1045 steel rod * 6061 T-6 aluminum seal housing with dual PTFE coated bronze rod guides * Viton® O-ring with U-cup seal * 6061 T-6 aluminum piston * Automatic velocity sensing valve * Anodized 6061 T-6 aluminum end cap with polyurethane wiper seal * Replaceable Delrin® contact pad for smooth and quiet operation * Tunable by adjusting the nitrogen pressure and or oil volume * Schrader valve with cap for quick and easy pressure adjustment * Adjustable from 75 to 300 psi; ships pre-charged to 200 psi--a great starting point for tuning your suspension
Not Yet Reviewed
$399.99
For all of you buggy racers or off-road runners, Trail-Gear has the ideal setup for mounting your limiting straps. These clevis strap kits are made from chromoly steel, then zinc plated to prevent corrosion. A threaded clevis shank, adjustment spring, and hardware are also included. Trail-Gear brings you an easy way to mount your straps and help protect your shocks on even the most extreme terrain.
( 5 )
$29.99
Building a fully hydraulic steering system can be quite a project. Thankfully, Trail-Gear has taken all of the guesswork out of the process with these complete, user-friendly hydraulic steering kits! Everything you will need is included, such as mounting brackets specifically designed for Toyota apps. The steering pump has an all-steel housing and emits 4.5 gpm of flow and 1,650 psi of pressure. Each high-pressure hose is steel-braided with crimped-on ends. These kits are available in 6, 8, and 10 in. ram sizes, and are ideal for use with links and most leaf spring applications. Kits include: * 6, 8, or 10 in. double-ended ram and clevis kit * Orbital (100 ml, 125 ml, or 160 ml) * Full hydraulic steering pump with pulley * Tie rod kit * Double-ended ram mounting kit * Steering column * Orbital mounting kit * Reservoir with filter * Cooler * Power steering belt * Complete hose kit * All necessary hardware
( 4 )
$449.99
—
$2,499.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
