Availability
Showing In Stock Items. Show All 104 Items.
Go retro with Edelbrock Performer RPM LS1 intake manifold kits. These kits give you the opportunity to use a carburetor on your originally computer-controlled engines. Performer RPM LS1 kits include a wiring harness and an MSD ignition controller (compatible with 24x and 58x) which works with OE sensors to fire the coil-on-plug ignition system and offers a choice of six timing curves. A special throttle and transmission bracket that works with 700R-4, 200R-4 and Turbo 350 transmissions is included. Make your LS1 engine an easy retro-fit into any muscle car, street rod or marine application with American-made Edelbrock Performer RPM LS1 intake manifold kits.
( 10 )
$1,027.95
Offenhauser Dual Port intake manifolds feature completely separate runner systems for the primaries and secondaries for more power across the rpm range. At low-load, the primaries feed the air/fuel charge through the smaller bottom passages at near sonic speed, improving power and efficiency. When the secondaries open, their charge goes through the bigger, cooler upper passages. Then, in turn, it is rammed into the cylinders when it encounters the high-velocity mix from the primaries. The results are better fuel economy and a 15-30 percent power increase across the entire rpm range. These manifolds are available in a variety of styles and options for many year/make and engine applications.
( 45 )
$799.99
—
$841.99
On Sale
Holley offers EFI Hi-Ram intake manifolds for a variety of applications, including many vehicles from the 1950s, '60s, '70s, and '80s with a Chevy small block Gen I engine. Fuel rail kits are provided and have mounting for both long and short type fuel injectors. These manifolds offer the performance potential and the appearance of professionally prepared billet and fabricated racing intake manifolds at the affordable price of a cast-aluminum product. They deliver 21st century performance for the iconic small-block Chevy engine. * Model 300-950 is of standard Hi-Ram configuration with a "top-feed" plenum and a plenum top designed to accept up to an 105mm Gen IV LS 4-bolt throttle body, including drive-by-wire throttle bodies. * Model 300-951 is a hood-height friendly Hi-Ram variation which has a "front-feed" plenum and a forward-facing throttle body flange which accepts an up to 95mm LS 4-bolt throttle body, also, including DBW throttle bodies. It's an upgrade replacement for the Holley/Weiand Stealth-Ram intake manifold which was a popular manifold used to significantly improve the performance of 1985-92 GM 5.7L TPI fuel-injected engines. The 300-951 system installs under the OE hood for Gen 1, 2, and 3 Camaros and Firebirds. It should be compatible with most applications with a mild cowl induction hood. * Uses drive-by-wire or cable-actuated GM Gen IV LS 4-bolt throttle bodies * Throttle cable bracket is supplied in the kit * GM Gen IV LS MAP sensor port. Also has provisions for (1) 1/8 NPT, (1) 1/4 NPT, (1) 3/8 NPT fittings to the plenum * Power band: 1,500-8,000 rpm * Black anodized EFI fuel rails are machined for -6 AN O-ring fittings and come included with these EFI Hi-Ram kits * Plenum top gasket type – 3/32 in. round O-ring cord * Cast 356-T6 aluminum construction, natural, satin as-cast aluminum finish * Requires the use of early type GM or small cap MSD or Holley distributors. Not compatible with HEI distributors * 1.95 in. tall x 1.25 in. wide port flange openings
( 2 )
$999.95
$898.95
—
$1,049.95
Old school looks, modern performance, and advanced manufacturing all rolled into one—Trick Flow's® R-Series Tunnel Wedge intake manifold for Ford 390-428 delivers just that. Part of the original Tunnel Wedge's cool factor was its appearance, so Trick Flow® took special care to match the looks of the legendary OEM version while improving upon its performance. Trick Flow® was able to maintain the original carburetor locations—but on the inside of the manifold, Trick Flow® overhauled the port design for more airflow and incorporated a new O-ring sealed bottom plate. Cast in premium-grade A319 aluminum, the manifold is topped with carb flanges machined for original Ford FE Tunnel Wedge-style square bore carburetors. Mounting hardware is included.
( 4 )
$999.99
On Sale
The Trinity Series intake manifolds is BTR's latest offering in high-quality cast aluminum intake manifolds for LS7 engines. Their short runner, 3-piece design allows for the ultimate in application flexibility and is similar in concept to billet intakes costing thousands more. Optimum operating range is 6000-8500 rpm and is primarily intended to bridge the gap between N/A and Boosted applications. These intake manifolds utilize the high LT1 throttle body position and accepts DBW or cabled throttle bodies, yet will fit in the tight confines of the C7, C6, C5 Corvette, as well as the popular F-body platforms. BTR Trinity Series intake manifolds come semi-assembled and includes all hardware required to bolt it on. Additional features: * Available in choice of silver or black satin texture powdercoat finishes * Design incorporates two runners and an interchangeable plenum * Both the port mouth radius and the port match are CNC-machined * Seal is generated by eight entrapped O-rings at the runner/plenum interface and is clamped by M6 stainless steel socket head cap screws * Port seals are achieved SAE O-rings seated in a dovetailed O-ring groove * Incorporates two ports on the side of the throttle body boss and on the rear * Runners and plenums can be purchased separately
( 1 )
$929.99
—
$999.99
$836.99
—
$899.99
On Sale
Holley LS Modular Lo-Ram EFI intake systems have a top-feed plenum entry configuration, designed to allow the currently available Hi-Ram 105mm plenum tops to be fitted to a low-profile base intake manifold. The short runner, low-profile base intake manifold intended for forced induction applications and was conceived to package with an air-to-water plenum-mounted intercooler—with a shorter overall height than is possible with other existing intake manifolds. Using a modular design, the top-feed plenum configuration with 105mm top keeps the overall height at just 9.07 in.! Additional features and specs include: * Cast aluminum construction * Modular design allows the use of the included top-feed plenum entry * Designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads * Will also work with OE or aftermarket cylinder heads * Designed for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000 to 8,000 rpm, depending on application * Low height to aid the packaging of a plenum-mounted air-to-water intercooler in a top-feed configuration (or to fit under a stock or mildly modified hood in the front-feed configuration) * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits come with two sets of brackets—a set for long (usually standard length) fuel injectors, and a set for short (such as Pico or LS7) fuel injectors
( 1 )
$1,099.95
$988.95
On Sale
Victor intake manifolds make use of Edelbrock's extensive knowledge of induction technology to produce maximum power and torque and are designed for all forms of competition. These single-plane, high-rise manifolds are arguably the most popular and flexible manifolds in racing today. You'll find them on oval tracks, in drag racing, and on NASCAR engines because they boost power where these engines need it the most--from 3,000 rpm to 8,500 rpm. All Victors have extra material for port matching and are available to fit either square bore or Dominator carb flanges.
( 24 )
$1,017.95
Dart dual plane intake manifolds are designed to improve torque, add horsepower, and make that otherwise stock engine look a little more aggressive. They are manufactured from durable cast aluminum and are machined to tight tolerances for excellent flow characteristics. The manifolds' optimized runner length and plenum style offer improved low end to midrange performance.
( 3 )
$814.95
Edelbrock Performer EPS intake manifold and carburetor kits contain all of the necessary pieces to upgrade your induction system. They include an Edelbrock Performer EPS aluminum intake manifold with either a natural aluminum finish or an EnduraShine finish, an intake gasket set, intake manifold bolts, a carburetor stud kit, and a Performer Series 600 cfm electric choke carburetor. The EnduraShine finish is a bright silver chrome finish that resists discoloration from heat and features a clearcoated top coat to enhance abrasion and chemical resistance. The Edelbrock Performer EPS intake uses an all-new runner design tuned to produce substantial torque increases. Ready for a change? Try Edelbrock Performer EPS intake manifold and carburetor kits for your musclecar, hot rod, truck, or ordinary street vehicle.
( 60 )
$830.95
Designed for 1988-96 Ford trucks (under 8,600 GVW) with fuel-injected 5.8L V8 engines, the modular design of these Edelbrock manifolds incorporates the latest airflow technology for maximum torque gains in the mid range. Other features include a broad power range from idle to 5,500 rpm and a removable plenum cover that allows access to runners. The base manifold is CNC port-matched to the upper manifold for maximum power, and they accept all stock hardware. The upper is powdercoated light titanium gray, and the base is as-cast.
( 11 )
$1,132.95
On Sale
Holley LS Modular Lo-Ram EFI intake manifolds are designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications and a 105 mm throttle or similar models. The base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood in the front-feed configuration. The modular design allows the use of front-feed plenum entry, while intake design facilitates custom inlet duct and throttle body placement. Additional features and specs: * Cast aluminum construction with satin silver finish * Modular design allows the use of front-feed plenum entry * Clears 4th Gen Camaro and C5 Corvette cowls and hoods without modification * With forced-induction and the short runner length the engine rpm at which peak power occurs is more likely to be coupled to the supercharger or turbocharger being used * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits include two sets of brackets; a set for long (usually standard length) fuel injectors and a set for short (such as Pico, or LS7) fuel injectors
( 8 )
$949.95
—
$1,016.95
$853.95
—
$914.95
On Sale
Holley EFI LS Mid-Rise intake manifolds are designed for your high performance race engine. They're an excellent choice for street and performance street/strip applications. They're intended for big cube and high-rev applications without height limitations. The modular design of these manifolds offers a runner length and as-cast tapered cross-section design that works for a wide range of engine configurations. The included fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. Build maximum performance with EFI LS Mid-Rise intake manifold bases from Holley.
( 7 )
$1,099.95
$988.95
Prepare your pony for the street and strip! The Edelbrock Performer 5.0 RPM II manifolds are designed for 1986-95 5.0L Mustangs and have shown significant gains in horsepower over existing designs in the 1,500 to 6,500 rpm range. That makes these intakes ideally suited for street and strip applications. The manifolds consist of a V-shaped crossover with an increasing cross-sectional area, which passes over to eight large tapered runners. The upper manifold is powdercoated light titanium gray.
( 5 )
$990.95
—
$1,081.95
On Sale
Holley EFI LS Hi-Ram intake manifold bases are cost-effective alternatives to fabricated sheet metal for high performance applications where induction system height is not limited. Coupling these cast aluminum Hi-Rams with the high flowing LS-style cylinder heads has outstanding potential for N/A and forced induction applications at a budget-minded cost. These modular lower manifolds accept a wide range of carbureted and EFI tops, making them attractive to builders and fabricators as the perfect foundations for custom induction systems. Fuel rails are included and machined for -8 AN O-ring fittings with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system. The aggressive, bold, race-bred styling of Holley GM LS modular Hi-Ram lower manifolds will make bad intentions clear for drag race, muscle car, marine, off-road, sand rails, pulling trucks, track, and street-rod applications.
( 1 )
$899.95
—
$999.95
$808.95
—
$898.95
Edelbrock Performer RPM Air-Gap LT1/LT4 intake manifolds utilize a proven short runner tunnel-ram style that provides that next level of performance you have been looking for. They are both direct stock replacements for OEM equipment with all required emissions features. The Edelbrock Performer RPM Air-Gap LT1/LT4 intake manifolds are manufactured from aluminum and feature a natural finish. Edelbrock's patended Air-Gap design delivers a cooler and denser air stream for maximum power output. They are designed to work with either stock, 52mm or 58mm Edelbrock throttle bodies, and will accept OEM fuel rails.
( 4 )
$822.95
These Performer RPM FE intake manifolds from Edelbrock are designed for high-performance street Ford FE V8s with standard low/medium-rise or Edelbrock Performer RPM FE heads. Their dual-plane constant cross-sectional area design builds low and mid-range acceleration, while optimized runner paths make top-end horsepower. These manifolds have a provision for adding the PCV or breather flange at the rear, and no exhaust crossover passage.
( 37 )
$865.95
Edelbrock Victor tunnel ram intake manifold bases are a modern updated design to their very successful Victor Ram 2-R Tunnel Ram intakes, which were first released over 35 years ago. They are designed for use with 468-582 C.I.D. standard-deck Chevrolet V8 engines with conventional rectangular port cylinder heads. This new and improved design has 7 in. long runners with close to 5.5 square-inches at the plenum, making them 25 percent larger than the current Victor Ram 2-R Tunnel Ram bases. These are the ideal intake manifolds for any modern high horsepower demanding application.
( 1 )
$979.95
—
$1,060.95
On Sale
Holley's low-profile intake manifold for Ford's 7.3L Godzilla engine, when paired with a 20-340/20-340BK oil pan and accessory drive kit, allows for easy installation into vintage vehicles, kit cars, and other space-restricted applications while retaining the factory hood. The design focus for these manifolds was equal cylinder distribution and great street manners. The low-profile intake manifolds offer a much cleaner alternative to the original plastic intake; they provide anywhere from 2 to 3.5 in. of additional clearance, will correct the OE throttle body angle by 55 degrees, and increase the opening to 92mm. With three throttle body options, sturdy cast aluminum construction, a removable lower panel, and long runners to maintain the 7.3L's already substantial torque offering, this is a must-have for any Godzilla project. Throttle Body Options: * 1) 1986-1993 5.0L Mustang style drive-by-cable throttle bodies * 2) 2020-2023 7.3L drive-by-wire throttle body * 3) 2020-2023 GT500 drive-by-wire throttle body (requires P/N 300-903) Compatible Engine Components: * 1) Factory accessories as well as Holley accessory drives (except for 20-380 and 97-409) * 2) Factory fuel rails and Holley 534-265 / 534-266 billet rails Intake manifold features: * Lower profile (2+ inches) than the OE intake manifold * Sturdy cast aluminum construction that will hold up to the elements and forced induction * Perfect complement to Holley's Godzilla accessory drive and oiling system (20-320 / 20-320BK / 20-340 / 20-340BK) for fitment into tight engine bays * Removable lower intake panel that can be removed for additional porting, nitrous, etc. * Incorporates long runners for solid low-end torque * Includes throttle body gasket and all necessary O-rings and adapters to mount to the engine * Compatible with OE or Holley accessory drives and OE or Holley fuel rails * Corrects OE throttle body angle by 55 degrees * Available in natural or black powdercoat finish
Not Yet Reviewed
$927.95
$834.95
On Sale
FiTech Ultimate LS Loaded intake manifold kits are just like the systems, but without the ECU and hand-held controller. FiTech Ultimate LS Loaded intake manifold kits will have: * Low-profile 92mm or 102mm (750 hp kits only) inlet aluminum fabricated intake with 1,500 to 6,500 rpm powerband, 3mm construction, TIG-welded, black anodized with embossed FiTech logo * CNC-machined with O-ring gaskets and hardware included * High-flow cable operated 92mm or 102mm (750 hp kits only) throttle body * Parabolic inlet machining for smooth throttle transitions, same as OE * Throttle body features progressive linkage pulley with double-return spring and adjustable stop * Billet fuel rails with AN fittings and fuel crossover * 36 or 55 (750 hp kits only) lbs./hr. flow-matched injectors
( 6 )
$965.00
$820.25
These Ford Performance Parts 4.6L 3-valve performance intake manifolds feature high-flow runners and an open plenum design for maximum flow, while still fitting underneath stock Mustang hoods. They are manufactured from lightweight composite plastic and have been tested up to 20+ psi; perfect for use in forced induction applications. Ford Performance Parts 4.6L 3-valve performance intake manifolds include a set of intake gaskets to complete the installation. Additional technical information: * Works well with Ford Performance M-6550-3V hot rod camshafts, M-6049-N3VPA high performance CNC-ported 3V cylinder heads, and M-9926-3V 62mm throttle bodies * Less heat soak than aluminum intakes * MAP sensor mounting boss for speed-density applications * Calibration required (not included) * Throttle body not included * Does not fit with Ford Performance strut tower braces
( 11 )
$786.99
Edelbrock Victor spread-port intake manifolds are specifically designed for high-rpm drag racing engines using Brodix Big Duke or Dart Big Chief cylinder heads. They feature a runner section area of approximately 4.75 sq. in. The intake manifolds require port matching to the cylinder head for optimum performance and will produce higher top-end horsepower while maintaining consistency and throttle response.
Not Yet Reviewed
$887.95
—
$955.95
On Sale
Holley Sniper EFI fabricated intake manifolds are budget-friendly and performance laden! These durable Holley hi-ram manifolds feature 3mm (1/8 in.) thick T-6061 sheet aluminum construction with 100 percent TIG welds. The EFI versions have 92mm or 102mm throttle body openings, as well as runners with tapered tops to increase velocity and evenly distribute airflow. They also include 3/8 in. fuel rail kits and, of course, are branded with the Holley Sniper EFI logo. Budget and performance go hand-in-hand when it comes from Holley in the form of their Sniper EFI fabricated intakes. Order the model and options recommended for your make/engine application.
( 17 )
$949.95
$763.95
—
$899.95
On Sale
Holley modular Ultra Lo-Ram intake manifold kits feature a design custom-made for LS engines equipped with LS cathedral port cylinder heads, as well as OEM or aftermarket models. They provide an ideal solution for forced-induction (supercharged or turbocharged) engine applications and select throttle bodies—plus the base intake manifold features a lower overall height to fit under a stock or mildly modified hood. The included fuel rail kits come with two sets of brackets: a set for long (usually standard length) fuel injectors and a set for short (such as Pico or LS7) fuel injectors. The Holley LS modular Ultra Lo-Ram EFI intake manifolds best suited for your application also allow the use of front-feed plenum entry. More product features, items, and notes include: * Designed for forced-induction engine applications with peak power at 7,000 to 8,000 rpm (depending on the application) * Intake design facilitates custom inlet duct and throttle body placement * Allows design and fabrication of special throttle body adapters or inlet ducts for custom installations * Different finishes available for the best look to match your ride * Mounting hardware * With forced induction and the short runner length, the engine rpm at which peak power occurs is more likely to be coupled to the supercharger or turbocharger you use
Not Yet Reviewed
$999.95
—
$1,049.95
$898.95
—
$943.95
Trick Flow® Track Heat® EFI intake manifolds deliver a perfect balance of airflow distribution and velocity. The result is excellent low-end torque and superior horsepower from 1,500 to 6,500 rpm. These units are available in kits with a natural finish aluminum lower manifold and an aluminum upper plenum in your choice of silver powdercoat, black powdercoat, and natural finishes. The manifolds have a 75mm throttle body inlet and are designed for use on non-EGR engines. Additional features: * Small cross-section with 12.200 in. runners * Overall height to the upper manifold flange is 10.200 in. * Overall height to the lower manifold flange is 4.625 in. * 2.000 in. x 1.200 in. port size at head * 2.000 in. x 1.200 in. port size at mating flange The upper plenums and lower manifold are also available separately.
( 3 )
$888.99
—
$892.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
