Availability
Showing In Stock Items. Show All 24 Items.
Tear up the track with a Trick Flow® Track Heat® intake manifold! These aluminum dual plane manifolds feature a one-piece spider-type design with extended, high-flow runners and a raised plenum floor for more horsepower and torque. Other highlights include A319 aluminum construction, integral bosses for nitrous nozzles, and extra material for custom porting. These intake manifolds deliver peak power in the in the 3,000 to 7,000 rpm range and work with all square bore-style carburetors.
( 17 )
$524.99
On Sale
Holley LS split design carbureted intake manifolds are single-plane racing units designed with performance in mind. They feature a race-bred, 2-piece split feature that was previously only found on the most expensive race intakes. The manifolds will fit GM LS Gen III engines with cathedral port heads—and are intended for 4150-style square bore flanged carburetors or throttle body EFI. The LS Race single-plane intake manifold was designed for high performance/racing engine applications, 5.3 to 6.2+ liter displacement—and maximum engine speeds of 6,000 to 7,000 rpm, depending on the engine combination. This single-plane design provides optimal performance across the rpm spectrum, while providing maximum performance up to 7,000 rpm. Features include: * Maximum performance race design with hood clearance consideration * Lighter than other split race intakes * Split feature allows disassembly of the intake for direct access to internal plenum and port surfaces, making custom porting and matching a snap * Shoulder bolt locators and O-ring seal make reassembly simple and precise * 33 to 50 percent the price of other split race intakes * Vacuum port options: Two 1/8 in., one 1/4 in., and one 3/8 in. NPT ports at the carb flange
( 6 )
$725.95
$583.95
—
$749.95
On Sale
Holley LS Modular Lo-Ram EFI intake manifolds are designed for GM LS Gen III and IV engines equipped with GM LS1/LS2/LS6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications and a 105 mm throttle or similar models. The base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood in the front-feed configuration. The modular design allows the use of front-feed plenum entry, while intake design facilitates custom inlet duct and throttle body placement. Additional features and specs: * Cast aluminum construction with satin silver finish * Modular design allows the use of front-feed plenum entry * Clears 4th Gen Camaro and C5 Corvette cowls and hoods without modification * With forced-induction and the short runner length the engine rpm at which peak power occurs is more likely to be coupled to the supercharger or turbocharger being used * High-volume fuel rails and mounting hardware included with 3/4 in.-16 O-ring ports (8 AN) * Fuel rail kits include two sets of brackets; a set for long (usually standard length) fuel injectors and a set for short (such as Pico, or LS7) fuel injectors
( 8 )
$649.95
—
$749.95
$583.95
—
$673.95
Ford Performance has released the 2018-2023 Mustang GT intake manifold to be available as a replacement part for your 2018-2023 5.0L, or as an upgrade for your 2011-2017 5.0L Coyote engine. Custom calibration is required for the 2011-2017 models. When upgrading to this intake, you can expect improved horsepower and torque over the stock manifold. For the quality parts you need for your Ford, choose Ford Performance Parts.
( 3 )
$509.99
On Sale
Holley is the new standard in EFI! The Holley EFI LT1 Gen V Lo-Ram intake manifolds are designed for GM Gen V LT engines equipped with GM LT cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine application. The top-feed plenum base intake manifold is designed with a reduced overall height to fit under a stock or mildly modified hood. The Lo-Ram provides a low-profile modular intake manifold that's suitable for use with plenum mounted air-to-water intercoolers for boosted applications. Various Hi-Ram plenum top options are available to complement the top-feed base intake manifold kits and fabrication flanges are offered to aid fabrication of plenum tops for custom installations. Features: * Designed for GM Gen V engines equipped with GM LT type cylinder heads * As-cast aluminum (satin) and black powdercoat finishes available * 105mm diameter throttle body opening accepts OEM 4-bolt LS/LT DBW or Holley LS/LT throttle bodies * Engineered for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000-8,000 rpm, depending on the application * Low-height top-feed plenum profile to fit under a stock or mildly modified hood * Modular design and top entry plenum flange allows the use of popular Holley Hi-Ram plenum tops, as well as facilitating custom fabricated plenum tops—base manifold, plenum tops, and fabrication flanges available as separate kits * Designed for the accommodation of plenum mounted air-to-water intercoolers for boosted applications * Available models for OE direct fuel injection only and with port fuel injection provisions—for the port fuel injection option, the high-volume fuel rail kit includes hardware and brackets to accommodate long (usually standard length) fuel injectors or short * Kits with port injection provide high volume fuel rails with 3/4 in.-16 O-ring ports (8 AN) * Mounting hardware is included * 3.18 in. taller than a factory LT1 manifold
( 1 )
$1,049.95
$579.95
—
$749.95
Trick Flow® R-Series A460 Intake Manifolds deliver significant performance gains in 500-plus cubic inch engines. They are single quad intake manifolds made from lightweight A319 aluminum and include bosses for nitrous or fuel injection. The special one-piece, spider-type design with high-flow, extended individual runners and a raised plenum floor produces sizeable power increases in the 3,500-8,000 rpm range. Additional highlights include extra material for custom porting and a Dominator-style carb mounting pad. R-Series A460 manifolds can only be used with Trick Flow® PowerPort® A460 series cylinder heads.
( 3 )
$749.99
AFR Eliminator Series intake manifolds are the perfect way to "eliminate" your competition! These cast aluminum performance intakes have a 23-degree manifold configuration. They're designed for standard location intake port cylinder heads. Additional coolant outlets have been added at the rear of the manifold for custom cooling systems. Eliminator intakes can be run "as cast," right out of the box; however, AFR does recommend having the runner exits be "port matched" to your particular cylinder heads for optimal performance. Additional bungs have been cast into the top of the intake runners for EFI injectors or nitrous nozzles. Multiple heights and rpm ranges are available; order the manifold recommended for your application.
( 24 )
$669.90
On Sale
Developed with performance in mind, Holley EFI LS single plane split-design race intake manifolds feature a race bred, 2-piece split design that was previously found only on the most expensive race intakes. These manifolds will fit GM LS Gen III engines with cathedral port heads for high performance/racing engine applications with 5.3 to 6.2 liter displacement and maximum engine speeds of 6,000 to 7,000 rpm, depending on the engine combination. The single-plane design provides optimal performance across the rpm spectrum, while the split feature, which allows disassembly of the intake for direct access to internal plenum and port surfaces, makes custom porting and matching a snap. Shoulder bolt locators and an O-ring seal makes reassembly simple and precise.
( 4 )
$821.95
$628.95
—
$738.95
On Sale
Make Holley SBF Hi-Ram EFI intake manifold bases the foundation for your custom induction system. Their modular design allows them to accept a variety of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. Aggressive looks and bold styling make your bad intentions clear—whether you're drag racing, truck pulling, or making waves in your boat—when you start with the Holley Hi-Ram EFI intake manifold bases. SBF Hi-Ram EFI intake manifold base features and specs: * Manifold base only designed for 8.2 in. deck height * Cast aluminum construction * Available in natural cast aluminum (satin) or black powdercoat finish * EFI fuel rails are machined for -8 AN O-ring fittings, with passages large enough to accommodate high fuel flows and dampen pressure pulsations in the fuel system
( 1 )
$996.95
—
$1,049.95
$648.95
—
$682.95
Trick Flow® single plane, rectangular port R-series intake manifolds for your big block Chevy features high-flowing extended runners and raised plenum floors to increase horsepower and torque. They are designed for 500-plus cu. in. engines and deliver maximum power between 3,500 and 8,000 rpm. Plus, their integral bosses for nitrous injection and extra material for custom porting. For use with Dominator-style carbs.
Not Yet Reviewed
$699.99
On Sale
The design of Holley Hi-Ram GM LT1 lower manifolds allows for easy disassembly to do custom porting, use multiple tops, or create custom induction systems. Each runner has a large radius where it meets the plenum, as well as an optimized taper and cross-sectional area to perform in a wide variety of engine configurations. The bases are available with or without port EFI provisions. Are you looking for the ultimate performance? Begin with Holley LT Modular Hi-Ram lower intake manifolds. Features include: * Modular design with removable top * Overall height: 13.34 in. with EFI top (95mm or 105mm) * Overall height: 12.10 in. with carb-style top (2 x 4150 or 2 x 4500) * Height at plenum flange: 9.44 in. * Port size: 2.06 in. high x 1.53 in. wide * Runner length: approximately 6.5 in. * Large plenum volume of 549 cu. in. with 1 x 95mm or 1 x 105mm throttle body top * Available with or without injector ports in the runners * Intakes with injector ports include fuel rails with dual mounting (1.48 in. or 2.56 in.) O-ring to O-ring injector length * Anodized fuel rails, laser-etched, and machined for -8 AN O-ring fittings * Rear of plenum machined for MAP and three vacuum ports * Head flange has clearance for fuel supply to a high-pressure pump * Increased runner wall thickness for custom porting at the plenum-to-runner entry on each runner * O-ring seals at cylinder heads and plenum top * Top-mounted screws on plenum top (all except front two screws) * Available top options: 1 x 95mm, 1 x 105mm, 2 x 4150, 2 x 4500, or blank flange for custom throttle bodies (all sold separately) * 3,500-8,000+ rpm power band
Not Yet Reviewed
$749.95
$673.95
Designed for engines that work in the 3,500-8,000 rpm range, Trick Flow® Track Heat® intake manifolds for your Ford 429/460 deliver race-like power and torque. These single plane high-rise manifolds feature a one-piece spider design, high-flow extended individual runners, a raised plenum floor for improved fuel atomization and flow velocity, integral bosses for nitrous or fuel injection nozzles, and extra material for custom porting. These Track Heat® manifolds are made from A319 aluminum and are for use with square bore four barrel carbs.
( 6 )
$699.99
On Sale
Holley Sniper carbureted fabricated intake manifolds are budget-friendly, sheet metal style intake manifolds. Each manifold is precision-fixtured and welded for a perfect fit and structural integrity. They are available for carbureted Chevy LS, Ford Coyote, small block Chevy, big block Chevy, and small block Ford engines. Features include: * Available for single or dual carburetor applications * 3mm (1/8 in.) thick T6061 sheet aluminum construction * More durable than competitive intakes * Bead-blasted silver or black anodized finishes * 100 percent TIG-welded * Custom Holley Sniper logo
( 37 )
$912.95
$502.95
—
$764.99
On Sale
Holley is the new standard in EFI! The Holley EFI LT1 Gen V Ultra Lo-Ram intake manifold kits are designed for GM Gen V LT engines equipped with GM LT cylinder heads. They will work with OE or aftermarket cylinder heads. The Ultra Lo-Ram intake manifolds are designed for forced induction (supercharged or turbocharged) engine applications. The front-feed base intake manifold is designed with a lower overall height to fit under a stock or mildly modified hood. The Ultra Lo-Ram provides a very low-profile modular intake manifold along with various fabrication flanges to aid the fabrication of special throttle body adapters or inlet ducts for custom installations. Whether you're engine swapping your classic car or need to manage added horsepower in your twin-turbocharged drag radial race car, Holley EFI has the solutions you need to get your project up and running better than ever! Features: * Designed for GM Gen V engines equipped with GM LT type cylinder heads * As-cast aluminum (satin) and black powdercoat finishes available * 105mm diameter throttle body opening accepts OEM 4-bolt LS/LT DBW or Holley LS/LT throttle bodies * Engineered for forced induction (supercharged or turbocharged) engine applications with peak power at 7,000-8,000 rpm depending on the application * Only 0.97 in. taller than a factory LT1 manifold provides maximum clearance under a stock or mildly modified hood * Modular design and front entry plenum flange allows design and fabrication of special throttle body adapters or inlet ducts for custom installations—base manifold, plenum top, throttle body adapter available as separate kits * Clears C7 Corvette cowls and hoods without modification * Available for OE direct fuel injection only or with added port fuel injection provisions * Kits with port injection provide high volume fuel rails with 3/4-16 O-ring ports (8 AN). Mounting hardware is included * Ultra Lo-Ram kits with a burst panel flange are available, Ultra Lo-Ram billet burst panel duct is offered separately (PN: 300-608 clear anodized, PN: 300-608BK black anodized)
Not Yet Reviewed
$1,049.95
$558.95
—
$649.95
On Sale
Holley LS Modular Hi-Ram intake manifold bases could be the foundation for your custom induction system. Aggressive looks and bold styling make your bad intentions clear, whether you're drag racing, truck pulling, or making waves in your boat when you start with one of these Hi-Ram bases. Their modular design allows them to accept a wide range of carbureted and EFI tops. Plus, their runner length and tapered cross-section are designed to perform well for a wide range of engine configurations. When there's no limit on height, start your build with one of Holley's cost-effective LS Modular Hi-Ram intake manifold bases.
( 2 )
$771.95
$693.95
Offenhauser Triple Manifolds are ideal for situations where you want to get a nostalgic 3-carb look, but still have a custom appearance. They're designed to equalize fuel distribution to all cylinders, which improves fuel economy, and produces better power with smoother response across the rpm range. These manifolds are precision-machined from cast aluminum, some manifolds mount aftermarket 2-barrel carburetors and some are made for original equipment single-barrel carburetors. Offenhauser Triple Manifold intake manifolds are available for a variety of inline sixes and flathead V8s.
( 1 )
$563.99
Take the guesswork—along with meticulous work necessary for accurate port matching—out of dialing in your big cube engine build for huge power numbers with Trick Flow's R-Series 11R 227 port-matched carb-style EFI intake manifold. The A319 aluminum manifold's CNC Competition Ported runner treatment has been specially designed and machined with perfect port alignment on Twisted Wedge® 11R 227 cylinder heads. The high-flow, one-piece spider-type single plane design with raised plenum floor puts the powerband in the 3,500-7,500-plus RPM range. Custom-machined fuel injection nozzle ports accept standard Bosch and Siemens-type fuel injectors.
Not Yet Reviewed
$724.99
Take the guesswork—along with meticulous work necessary for accurate port matching—out of dialing in your big cube engine build for huge power numbers with Trick Flow® R-Series 11R 205 port-matched carb-style EFI intake manifold. The A319 aluminum manifold's CNC Competition Ported runner treatment has been specially designed and machined with perfect port alignment on Twisted Wedge® 11R 205 cylinder heads. The high-flow, one-piece spider-type single plane design with raised plenum floor puts the powerband in the 3,500 to 7,500-plus rpm range. Custom-machined fuel injection nozzle ports accept standard Bosch and Siemens-type fuel injectors.
Not Yet Reviewed
$724.99
Dorman intake manifolds are precision-engineered and durably manufactured to match the fit and function of the original manifold on specified vehicles. They are thoroughly tested to ensure top-quality OEM construction and superior reliability. Dorman manifolds are offered in different styles, and all will provide a trustworthy design with a perfect fit and reliable construction for your vehicle.
( 157 )
$539.21
On Sale
Edelbrock Pro-Flo XT EFI intake manifolds combine a user-friendly design with the latest technology. They're manufactured from aluminum and are available in a natural, polished, or black powdercoat finish for ultimate protection. Pro-Flo XT EFI intakes feature eight equal-length tapered runners and a large plenum. The fuel-injected manifolds are designed to deliver maximum horsepower and a broad torque curve throughout the 1,500 to 7,000 rpm range. Choose the model designed for your vehicle and cylinder head style application.
( 15 )
$746.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
