Availability
Aeromotive 7.0 gpm brushless variable speed gear pumps deliver ground-shaking performance with advanced technology. Aeromotive took what they learned from their mechanical spur gear pumps and engineered it to work in a compact flow-through design, creating a fuel pump that is able to move more fuel at pressures up to 150 psi without a drop in flow. Aeromotive true variable speed controller offers the advantages of built-in pump speed control via a dedicated 0 to 5 V analog DC input signal. The controller capitalizes on Aeromotive's existing brushless technology by reducing fuel flow during low engine demand and decreasing an already low current draw, therefore minimizing both motor heat and the introduction of environmental via reduced fuel recycling. Features include: * E85 compatible, reduce maximum fwhp by 30 percent * Lighter than the traditional external mount pumps * Reduced current draw at higher, EFI pressures * Extended service life in methanol and ethanol * New integral spur-gear pumping mechanism * 90 psi continuous operating pressure and up to 150 psi peak pressure, base plus boost * Integral, external brushless controller for clean installation, cooler fuel, and enhanced reliability * ORB-12 inlet and ORB-10 outlet ports * Requires straight 12 V DC to 16 V DC power supply * Not compatible with pulse modulated systems or fuel pump speed controllers Supports: * EFI -- Up to 4,800 fwhp on gas--naturally aspirated -- Up to 3,400 fwhp on gas--forced air induction -- Up to 3,360 fwhp on E85--naturally aspirated -- Up to 2,380 fwhp on E85--forced air induction -- Up to 1,680 fwhp on methanol--naturally aspirated -- Up to 1,190 fwhp on methanol--forced air induction * Carbureted -- Up to 5,400 fwhp on gas--naturally aspirated -- Up to 3,800 fwhp on gas--forced air induction -- Up to 3,780 fwhp on E85--naturally aspirated -- Up to 2,400 fwhp on E85--forced air induction -- Up to 1,890 fwhp on methanol--naturally aspirated -- Up to 1,200 fwhp on methanol--forced air induction
( 1 )
$1,715.99
Snow Performance Stage 2.5 N54/N55 direct port water-methanol injection systems are engineered specifically for BMW models with N54/N55 engines. These systems can increase your pump gas octane by 25 points and makes more power efficiently with a cooler running engine! The Snow Performance Stage 2.5 N54/N55 direct port systems come complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings, offering un-surpassed quality, reliability, performance and ease of the installation. In addition, Snow Performance direct port injection plates are the easiest, and the best-way to mount the water-meth nozzles on BMW N54/N55 engines. Simply fit between the head and intake manifold and enjoy the placement of six Hyper-Sonic nozzles right where you need it! Additional features and benefits include: * The Stage 2 uses a progressive VC-50 controller that proportionally injects more or less according to boost pressure * Start and full points are adjustable for engagement and delivery curve to match what the engine requires * Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol, and allows cooling and performance improvements over a wide range for improved drivability * The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller--all in one! * 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) LED screen displays boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes, allowing you to tailor the controller to match your OEM gauges or mix and match up to two colors Snow Performance N54/N55 direct port kit includes: * Direct Port Injection Plate * OEM O-ring gaskets to seal between injection plate and head * Required hardware for installation * Hardlines plumbed to distribution rail * Six No. 2 nozzles installed in plate * High-flow water methanol solenoids * N54/N55 engine specific boost tap * Everything needed for installation
Not Yet Reviewed
$1,503.90
On Sale
FiTech Easy Street 600 hp Total Package EFI swap kits make it easier for classic car owners to upgrade to EFI, enhancing reliability with a single part number. Each complete package features FiTech's proven Easy Street 600 hp throttle body as the heart of the system, delivering smooth and reliable performance. Along with each Easy Street is a new direct-fit EFI-ready fuel tank with a Go Fuel internal pump module, a high-pressure internal fuel pump, and a complete steel braided hose kit to get the fuel to the classic gold-finished throttle body. A high-flow serviceable filter and AN-style fittings are also included, making all the connections a breeze to install. Choose the FiTech Total Package designed for your vehicle.
Not Yet Reviewed
$1,956.99
$1,761.29
You'd be crazy to throw water into a gas tank and expect to get anywhere—but power and torque can be increased if you inject it into the incoming air charge with Nitrous Express water/methanol injection systems. Cooling the air charge allows for increased timing and the resulting performance benefits. These versatile units have a wide-open throttle switch for naturally aspirated vehicles and an adjustable boost-activated switch for forced induction models. Nitrous Express systems inject a fixed amount of fluid when the WOT switch or boost is activated—and continues until the switch opens again. They reduce intake temperatures and the need for timing retard when used with nitrous. Stage III kits come complete with a high-output pump, 3 qt. reservoir, nozzle, boost/RPM activated progressive controller, switch, hardware, and detailed instructions. Water has always been used to cool motors down, but with Nitrous Express water/methanol injection systems … it'll be heating things up!
Not Yet Reviewed
$1,628.74
Nitrous Outlet nitrous oxide plate systems come out of the box ready to deliver superior atomization. They spray up to 200 hp, but are capable of flowing up to 400 hp with additional jetting and a -6 AN main feed line upgrade. You'll get race-proven performance from the unique 6-port discharge design, guaranteeing the perfect mixture of fuel to nitrous. Overview: * Max flow 400 hp * 400+ hp solenoids * Anodized black aluminum plate and bottle (if included) * Wide-open throttle activation switch * Hardware, electric, and jetting included * E85 compatible with different jetting * Jetting included for 50 to 200 hp
( 3 )
$1,513.99
—
$1,976.99
On Sale
FiTech has some of the best-engineered and priced throttle body systems on the market. Their LS EFI 500HP fuel injection systems bring incredible ingenuity to the market. FiTech fabricated many aluminum parts for these systems, including the low-profile 92mm billet throttle body, high-volume billet fuel rails, and an intake manifold with 1,500 to 6,500 rpm powerband and 3mm construction. Sequential spark and fuel control mates 36 lbs./hr. injectors, a plug-and-play wiring harness, and a color touchscreen self-learning ECU. This allows for programing two fan control outputs, most tach and speedometer output drivers, and target AFR and timing on the fly. A suction cup mounting bracket puts the controllers at your fingertips and allows for impressive visual aids. The optional transmission control feature is suitable for 4L60, 4L65, 4L70, or 4L80 GM transmissions. FiTech LS EFI 500HP fuel injection systems with transmission controller provide impressive power and performance, while allowing you to save a little green for your next tires. Additional features: * Black anodized aluminum parts for style and corrosion resistance * High-flow, cable-operated throttle body * Bosch wideband-controlled * Stainless oxygen sensor bung * Compatible with car and truck coils * AN fittings and fuel crossover * Works with custom cams * Designed for applications making at least 6 in. of vacuum at idle * 24X and 58X crank and cam compatible * Programmable touchscreen hand-held controller with data log features
( 41 )
$2,082.99
—
$2,433.99
$1,666.39
—
$1,947.19
Aeromotive A2000 fuel pump kits include everything needed for a complete Aeromotive system installation in a carbureted application. Designed to provide outstanding performance through matched component selection and correct installation, these systems support a wide range of performance levels, from 500 to 2,500 hp. Tired of fuel delivery problems? Aeromotive A2000 fuel pump kits are your solution. Order the model best suited for your vehicle. Kit components include: * A2000 pump * Fuel pressure regulator * Fuel filter * Port fittings * Braided stainless steel hose * Hose ends * Wiring * All necessary installation hardware
Not Yet Reviewed
$1,952.20
On Sale
Holley Sniper 2 EFI Base Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * For applications using a vehicle specific EFI conversion tank and fuel pump, or already having a fuel system capable of the required 55-65 psi, these systems are offered without a pump and fuel lines * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected
( 9 )
$1,949.95
—
$2,149.95
$1,753.95
—
$1,933.95
Why convert your LML's fuel system from a CP4 to a CP3? Since its introduction, the CP4 has proven to be less reliable and less capable than the CP3 used in previous Duramax platforms—resulting in costly repairs for owners when a CP4 fails. You can improve your LML Duramax's reliability and fueling capability, as well as avoid costly failure with Fleece Performance LML CP3 conversion kits. They provide OEM fit-and-finish features, like Fleece's exclusive molded hoses for the fuel feed and return, high flow CP3 fuel fittings, and their valley feed line to support aftermarket lift pump applications. Fleece Performance LML CP3 conversion kits are offered with or without pump and the pump kits come in two different style pumps—a Bosch CP3 injection pump or Bosch CP3 pump with heavy-duty 10mm cam. Choose the kit that is right for you. All kits include: * CP3 to rail high pressure fuel line * High-flow CP3 feed and return fuel fittings * Preformed fuel feed and return fuel hoses * CP3 mounting adapter * Dosing injector distribution block, feed and return lines * FCA extension harness * Low pressure fuel feed line * Hardware kit
Not Yet Reviewed
$1,999.00
Edelbrock Performer RPM Dual Quad Air-Gap manifold and carburetor kits provide everything needed to convert from a single carburetor intake to a powerful dual-quad carburetor intake system for small block Chevys. These kits include the new RPM Dual Quad Air-Gap intake, two 500 cfm Thunder Series AVS carburetors (one manual choke, one electric choke), Edelbrock high-tech progressive throttle linkage, a fuel line, and intake manifold gaskets. These kits are available in your choice of natural or the popular EndraShine finish.
( 7 )
$1,865.95
—
$1,972.95
On Sale
FiTech Ultimate LS EFI 500 hp fuel injection systems with Go Fuel in-tank module combines incredible engineering and construction for top-of-the-line performance. FiTech fabricated many billet aluminum parts for their Ultimate LS EFI 500 hp systems, including a 92mm throttle body, high-volume fuel rails, and a 1,500 to 6,500 rpm powerband intake manifold. They combine sequential spark and fuel control with 36 lbs./hr. injectors, a plug-and-play wiring harness, and a color touch screen self-learning ECU. This allows for programing two fan control outputs, most tach and speedometer output drivers, and target AFR and timing on the fly. The Go Fuel in-tank module universal billet assembly can be used on tanks with a depth of 6 to 15 inches. The billet aluminum was designed with the supply and return ports in a parallel position to help route the fuel lines easily and evenly. The vent port is on the other side to ease routing the line near the fill tube. The two fuel ports are threaded to accept -6 AN O-ring boss fittings for a secure, leak-free connection. Whether you're starting with a 5.3 junkyard dog or a crate motor, FiTech Ultimate LS EFI 500 hp systems with Go Fuel in-tank module will look and run exceptionally. Additional Ultimate LS features: * Optional GM transmission control feature is suitable for 4L60, 4L65, 4L70, or 4L80 * Black anodized aluminum parts for style and corrosion resistance * High-flow, cable-operated throttle body * Bosch wideband-controlled * Stainless oxygen sensor bung * Compatible with car and truck coils * AN fittings and fuel crossover * Works with custom cams * Designed for applications making at least 6 in. of vacuum at idle * 24X and 58X crank and cam compatible * Programmable touch screen hand-held controller with data log features * Suction cup mounting bracket
( 1 )
$2,089.99
—
$2,440.99
$1,671.99
—
$1,952.79
On Sale
Holley Sniper 2 EFI Return-Type Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, return line, external regulator, filters before/after the pump, fittings/hardware, and a low profile return-type drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected
Not Yet Reviewed
$1,849.95
—
$2,099.95
$1,663.95
—
$1,888.95
On Sale
Holley Sniper 2 EFI Returnless Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters before/after the pump, fittings/hardware, and a low profile returnless drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Pre-set, internally regulated pump only requires a single feed line to the Sniper 2 unit * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected
( 2 )
$1,949.95
—
$2,199.95
$1,753.95
—
$1,978.95
On Sale
FiTech Go EFI 2x4 Power Adder 1200 hp fuel injection systems are for the guys who have 671 and 871 roots superchargers or make up to 1200 hp naturally aspirated on their dual-quad setup. These easy self-tuning systems work out of the box on your 2x4 blower plate as an inline setup or can be side mounted using custom linkages. Also, the kits are a bolt-on for the most popular normally aspirated dual-quad and tunnel ram manifolds, including the Edelbrock line of dual-quad manifolds, without any adapters! They fit and look like they belong there because they were designed to fit from the start. One throttle body handles all of the brains, while the second holds four additional injectors. These can also be used in cross ram and tunnel ram configurations. Application notes: Chevrolet, Pontiac, Ford, Chrysler, Dodge, Plymouth, etc. engines making 250 hp up to 1200 hp with a dual quad intake manifold. Replacement for any dual-quad carburetors for engines with 250 hp up to 1200 hp. Use the same size air cleaner you would normally use for your dual-quad carburetors. Product features: * 2.5 BAR internal MAP sensor * Suitable for up to 1200 hp * (8) Flow matched injectors * (2) Fan control * Blower and turbo ready * Support for nitrous * Boost and nitrous timing * Ignition timing control * Built-in pressure regulator * Air/fuel ratio tuning * Pro-tuning laptop software * Bright aluminum or matte black finish * NOTE: Some models include Go Spark CDI box Kit contents: (2) Diecast throttle body (1) Oxygen bung kit (1) Hand-held controller (1) CTS sensor (1) Hand-held controller cable (1) CTS adapter (1) Windshield mount (1) Mini USB cable (1) 4+2-Pin Connector (2) Return plug (1) Oxygen sensor (1) Gasket kit
( 11 )
$2,236.00
—
$2,347.99
$1,900.60
—
$1,995.79
On Sale
Holley Sniper 2 EFI Returnless Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters before/after the pump, fittings/hardware, and a low profile returnless drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Pre-set, internally regulated pump only requires a single feed line to the Sniper 2 unit * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected
( 2 )
$1,849.95
—
$2,099.95
$1,663.95
—
$1,888.95
On Sale
Holley Sniper 2 EFI Return-Type Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, return line, external regulator, filters before/after the pump, fittings/hardware, and a low profile return-type drop-in pump module(1.275-inches above the tank mounting surface) that is designed for universal installation into fuel tanks that range from 7 to 12 in. deep * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected
Not Yet Reviewed
$1,949.95
—
$2,199.95
$1,753.95
—
$1,978.95
On Sale
FiTech Go EFI 2x4 625 hp system fuel injection master kits are inclusive EFI kits with fuel delivery solutions. In these master kits, FiTech mates their 2x4 TBIs with either a Go Fuel in-tank or fuel cell pump module, or Go EFI in-line pump kit to provide everything needed to convert your carbureted vehicle to EFI. The throttle bodies are offered in two finishes. Choose the master kit with your preferred finish and fuel delivery solution. Go EFI 2x4 625 hp system lets everyone know you mean business with a pair of 4-barrels crowned atop your engine! The 2x4 is supplied with two throttle bodies, one with the brains and integral ECU, the other with the brawn. Both bodies feature four injectors and will support up to 625 hp (naturally aspirated). The system is supplied with two throttle bodies, handheld controller, cable and windshield mount, throttle body vehicle side harness, WBO2 sensor, bung kit, coolant sensor, gasket, mini USB cable, instructions, and warranty information. Fuel delivery options: * Go Fuel in-tank pump modules are offered in different styles, including regulated versions, and in different flow rates. They include gaskets, terminals, and clamps. * Fuel cell pump modules are offered in two models—single or dual pump. Each style features a billet machined top assembly and an internal regulator to maintain 58 psi. No return line is needed, and the module is machined to fit 12-bolt flange fuel cells or can be installed on any tank with the supplied hardware. * Go EFI in-line pump kits provide a FiTech heavy-duty pump with 40 ft. of high-pressure fuel hose, two fuel filters, including a serviceable 10-micron filter, fittings, mounts, and clamps.
( 4 )
$2,042.99
—
$2,112.99
$1,736.54
—
$1,796.04
On Sale
FiTech Ultimate LS EFI 750 hp fuel injection systems with Force Fuel combines incredible engineering and construction for top-of-the-line performance. FiTech fabricated many billet aluminum parts for their Ultimate LS EFI 750 hp systems, including a 92mm throttle body, high-volume fuel rails, and a 1,500 to 6,500 rpm powerband intake manifold. They combine sequential spark and fuel control with 55 lbs./hr. injectors, a plug-and-play wiring harness, and a color touch screen self-learning ECU. This allows for programing two fan control outputs, most tach and speedometer output drivers, and target AFR and timing on the fly. Force Fuel sump kits use your stock low-pressure manual or EFI pump to feed their sump tank. The pump is submerged in fuel for cooler and quieter running, and delivers 58 psi of high-pressure fuel to the throttle body at a rate of up to 340 lph (89 gph). For excellent performance and overall ease of operation, buy FiTech Ultimate LS EFI 750 HP fuel injection systems with Force Fuel sump system. Additional Force Fuel sump system features: * Low fuel level in the fuel tank will not result in pump starvation when vehicle is on a steep incline * Generally mounted in the engine compartment, but can be attached to the vehicle's chassis. * Supplied high-pressure hose includes 5 ft. of high-quality EFI -06 fuel line and fittings for plumbing from the Fuel Command Center 2.0 to the EFI throttle body Additional Ultimate LS features: * Optional GM transmission control feature is suitable for 4L60, 4L65, 4L70, or 4L80 * Black anodized aluminum parts for style and corrosion resistance * High-flow, cable-operated throttle body * Bosch wideband-controlled * Stainless oxygen sensor bung * Compatible with car and truck coils * AN fittings and fuel crossover * Works with custom cams * Designed for applications making at least 6 inches of vacuum at idle * 24X and 58X crank and cam compatible * Programmable touch screen hand-held controller with data log features * Suction cup mounting bracket
Not Yet Reviewed
$2,457.99
$1,966.39
Stromberg BIG97 carburetors feature 55 percent increased airflow to put out a whopping 250 cfm! They have the same standard 97 outside shape, but use enlarged 1.175 in. venturi with a super-efficient 20 degree entry angle. The accelerator pump discharge jets are smaller, and flared exit cones build power by slowing down the mixture to reduce turbulence into the manifold plenum. The result is 250 cfm. Stromberg BIG97 Tri-Power carburetors feature: * Signature 97 outside shape and styling * Cast iron base * Reinforced airhorn * Early plenum effect: allows all cylinders to draw from both barrels, giving you dual-plane drivability with a single-plane style top-end horsepower * New power valve circuits improve fuel conditioning: feeds top-end enrichment directly into the emulsion tubes * Ported distributor vacuum: switch in the brass plug (included) and connect your distributor to improve combustion efficiency in cruising mode; you'll run smoother and cooler, with more torque and better fuel mileage * Big S-jet twin-ball inlet valve: accepts 5/16 in. hard line and standard Stromberg fuel fittings * Four finishes available: original equipment style, chrome, chrome/black, or barn find (patina)
( 3 )
$1,560.00
—
$1,645.00
Nitrous Express Holley Hi-Ram Plenum Plate Systems take full advantage of the Holley Hi-Ram intake manifold. The Hi-Ram plenum plate bolts right in between the upper and lower intake manifold making the install super clean and quick. These systems inject nitrous and fuel above each cylinder from the side of the runner providing direct port-like distribution without having a flow restricting nozzle or spray bar. The Hi-Ram nitrous plate is made from billet aluminum with passages machined directly into the plate so there is no need to worry about spray bars breaking or spinning. The systems come complete with billet aluminum and carbon fiber Lightning solenoids, stainless steel braided lines, wiring, switches and every nut, bolt and connector needed to install the system. The systems ordered with a nitrous bottle include a billet aluminum Lightning 500 bottle valve and the stainless bottle brackets.
Not Yet Reviewed
$1,624.48
—
$1,872.94
Nitrous Express nitrous refill pump stations will allow you to fill your own nitrous bottles. They include the control valve and nitrous transfer lines. The refill pump stations feature the run dry technology for easy transfer.
Not Yet Reviewed
$1,792.22
Nitrous Outlet Stinger Plate nitrous oxide systems feature a second generation Stinger plate designed to work with either 4150 or 4500 flanged carbureted-style intake manifolds. The new billet aluminum Stinger plate has a larger conical cone than the previous version and is based off of the same technology as the Nitrous Outlet Nitrous Puck, enabling them to delivering up to 600 hp with proper jetting. The plate features 15 discharge ports for nitrous and 15 discharge ports for fuel. The 15 atomized plumes of nitrous and fuel exit from the center of the stinger into the intake plenum in a 360 degree pattern, completely saturating the air intake charge as it enters the intake plenum for even distribution. Nitrous Outlet Stinger Plate nitrous oxide systems include nitrous and fuel solenoids, solenoid brackets, a main feed line, relay, harness, jetting, hardware, and wiring.
Not Yet Reviewed
$1,503.99
—
$1,655.99
The NXd Stacker nitrous systems are the pinnacle in economical, safe add-ons for your modified diesel truck. Nitrous Express is committed to advancing nitrous technology. With these systems, they have succeeded in boosting torque and horsepower, dramatically reducing exhaust temperatures, and eliminating that ugly black smoke cloud. They allow you to stack nitrous on your existing diesel chip. These Stacker systems include Lightning series solenoids, a nitrous bottle with a Lightning 45 bottle valve, stainless braided feed line, nickel plated fittings and all necessary hardware need for installation. For the most up-to-date technology, always look to Nitrous Express!
Not Yet Reviewed
$1,573.95
Never be satisfied with the status quo! It is time for the next generation in crossbar nitrous plate technology. The CNC machined design eliminates round spray bars resulting in excellent atomization and cylinder distribution without rotation, sagging, or the disruption of airflow. These CNC-machined plates include a nitrous bottle with a custom solenoid. The Lightning Series solenoids feature CNC aluminum bodies with an integrated purge port, which allows for connecting a purge valve directly to the body of the nitrous solenoid, for less plumbing and clean looks. The kits also come with fittings, lines, switches, relays, and every nut, bolt, and electrical connector needed for installation.
( 4 )
$1,569.05
—
$1,963.37
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
